Agria 2500 Owner's manual

Category
Lawnmowers
Type
Owner's manual

This manual is also suitable for

Before commissioning the machine, read operating
instructions and observe warnings and safety instructions.
Operating Instructions No.
998 783-B 03.10
Briggs & Stratton Petrol Engine
- Recoil Starter Version
- Electric Starter Version
Yanmar Diesel Engine
- Electric Starter Version
Two-Wheel TractorTwo-Wheel Tractor
Two-Wheel TractorTwo-Wheel Tractor
Two-Wheel Tractor
2500 Hydro2500 Hydro
2500 Hydro2500 Hydro
2500 Hydro
OriginalOriginal
OriginalOriginal
Original
OperatingOperating
OperatingOperating
Operating
InstructionsInstructions
InstructionsInstructions
Instructions
2 agria-Two-Wheel Tractor 2500 Hydro
Please complete:
Machine Type No.:.......................
Identification No.:
..........................................................
Engine Type:..............................
Engine No.:................................
Date of Purchase:......................
For name plate, refer to
page 3/fig. A/4
For engine type and number, refer
to page 64/Fig. C/4 petrol engine
to page 68/Fig. D/17 diesel engine
Please state these data when order-
ing spare parts to avoid wrong deliv-
eries.
Only use original agria spare
parts!
Specifications, figures and dimen-
sions stated in these instructions are
not binding. No claims can be de-
rived from them. We reserve the right
for improvements without changing
these instructions.
This delivery comprises:
Operating instructions
Two-wheel tractor
Tool kit
Symbols
Warning – danger
Important information
Fuel
Fuel filter
Air filter
Choke
Forward
Reverse
Fast
Slow
Hydraulic system
PTO
Brake
Parking brake
Closed (locked)
Open (unlocked)
Clockwise
Lifting point
Grease gun
Lubrication point
- Service
= contact your agria-workshop
see separate engine
operating instructions!
Symbols, Name Plate
agria-Two-Wheel Tractor 2500 Hydro 3
Fig. A
Fig. B
Designation of Parts
12
11
8
7
10
1
2
6
5
4
3
9
28 27 26
22
1
21
1110
3
31 30
24
23
32
4
29 25
33
4 agria-Two-Wheel Tractor 2500 Hydro
Fig. A:
1 Inspection and filling opening for transmission / hydraulic oil
3 Idle speed shifting mechanism (bypass)
4 Nameplate (machine identification no.)
10 Lower steering handle
11 Steering bar
21 Eye bolt with cap nut, top
22 PTO-shaft
23 Eye bolt with cap nut, bottom
24 Transmission oil drain screw
25 Clamping lever for axle adjustment
26 Brake drum
27 Wheel hub
28 Oil filter cartridge
29 Hook for loading Belt
30 Engine
31 Stand
32 Weight mounting device
33 Socket (version diesel engine)
Fig. B:
1 Safety circuit lever
2 Lever for lateral steering bar adjustment
3 Lever for hydraulic steering gear left
4 Lever for hydraulic steering gear right
5 Lever for stepless adjustment of driving speed and forward-reverse
driving
6 Speed adjusting lever
7 Eccentric lever for central brake
8 Operating mechanism for PTO clutch
9 Signal light for PTO
10 Ignition lock
11 Ratchet bolt for height adjustment of steering
12 Operating hour counter/speed counter
Designation of Parts
agria-Two-Wheel Tractor 2500 Hydro 5
Amount of Delivery ........................... 2
Recommendations
Lubricants ......................................... 6
Maintenance and Repair .................. 6
Fuel ................................................... 7
Designation of Parts
.......................................3, 64, 68
1. Safety Instructions....... 8 - 13
2. Specifications
Dimensions ...............................14, 15
Wheel combinations/Track Widths . 16
Machine ..........................................18
Vibration Acceleration Value........... 19
Petrol Engine .................................. 19
Diesel Engine ................................. 20
Noise Levels .............................19, 20
Operation on Slopes.................19, 20
3. Devices and Operating Elements
Engine............................................. 21
Speed Control Lever....................... 22
Ignition lock..................................... 22
Warning signal ................................ 22
Safety circuit ................................... 23
PTO circuit ...................................... 23
Setting the Driving Speed
and Direction .................................. 24
Coasting Operation......................... 24
Hydraulic Steering .......................... 25
Brake Central.................................. 25
Steering Handle.............................. 26
Steering Handle Swinging Buffer ... 27
Lifting points ................................... 27
Drive Wheels .................................. 28
Axle Adjustment ............................. 29
Mounting/Dismounting
Implements .....................................30
Implements .....................................31
Battery ............................................ 32
Fuse ................................................ 32
4. Commissioning and
Operation
Commissioning the Machine .. 33,
34
Starting the Petrol Engine . 35, 37
Shutting off the Petrol Engine .....
........................................... 36, 38
Starting the Diesel Engine....... 39
Shutting off the Diesel Engine. 40
Operation ................................. 41
Danger Zone............................ 41
Working on Slopes .................. 42
5. Maintenance
Petrol Engine .................... 43 - 44
Diesel Engine ................... 45 - 48
Battery ..................................... 49
Machine ............................ 50 - 53
- Transmission/Hydraulic Oil .... 50
- Drive Wheels ......................... 51
- Brake ..................................... 51
- Wheel motors ........................ 51
- Hydraulic Hoses .................... 51
- Safety Circuit ......................... 52
- Adjustments on Levers.......... 52
- Steering Tower....................... 53
- Guide Channel ...................... 53
General Maintenance .............. 53
Storage .................................... 54
Varnishes, Wear Parts...... 55
Electrical Wirings ......56 - 57
6. Troubleshooting.....58 - 61
Inspection and
Maintenance Chart........... 62
Maintenance Schedule ..
63, 66
Conformity Declaration ... 69
Note fold-out pages!
Fig. A + B............................. 3
Fig. C (Petrol Engine)....... 64
Fig. D (Diesel Engine) ...... 68
3
5
6
2
1
4
Index
6 agria-Two-Wheel Tractor 2500 Hydro
Lubricants and
Anti-Corrosive Agents
Use the specified lubricants for engine
and transmission (see “Specifications”).
We recommend using bio-lubricating
oil or bio-lubricating grease for “open”
lubricating points or nipples (as speci-
fied in the operating instructions).
We recommend using bio anti-corrosive
oil for preservation of machines and im-
plements (do not apply on painted ex-
ternal covers). Oil can be brushed or
sprayed on.
Anti-corrosive agents are kind to the
environment and degrade fast.
Using ecologically safe bio-lubricants
and bio-anti-corrosives, you contribute
to environmental protection and to the
wellbeing of humans, animals and
plants.
Maintenance and
Repair
The trained mechanics of your agria
workshop carry out expert maintenance
and repair.
You should only carry out major main-
tenance work and repairs on your own,
if you have the proper tools and knowl-
edge of machines and internal combus-
tion engines.
Do not hammer against the flywheel with
a hard object or metal tools as it might
crack and shatter in operation causing
injuries and damage. Only use suitable
tools for pulling the flywheel.
Recommendations
agria-Two-Wheel Tractor 2500 Hydro 7
Petrol Engine
This engine runs smoothly on commer-
cial unleaded regular and supergrade
petrol as well as on leaded supergrade
petrol.
Do not add oil to petrol.
If, for environmental reasons, you use
unleaded petrol, make sure the fuel is
drained completely when shutting down
the engine for more than 30 days. This
is to prevent resin residues from depos-
iting in the carburetor, fuel filter, and
tank. Or add a fuel stabilizer.
For further instructions refer to "Engine
Preservation".
Recommendations Fuel
Diesel Engine
This Diesel engine runs on conventional
Diesel fuel of a min. cetane rating of 45.
Do not use Diesel fuel oil substitutes,
they may be harmful to the fuel system.
Fuel should be free of water or dust.
Winter operation:
To ensure reliable winter operation use
“winter diesel fuel”, to be purchased at
filling stations.
At outside temperatures of below -
15°C , take the following additional pre-
cautions:
add commercial flow conditioners
or
add paraffine oil to depress diesel pour-
point:
Paraffine winter summer
oil: diesel diesel
fuel fuel
pour-point
50% app. -31°C app. -25°C
30% app. -26°C app. -15°C
10% app. -20°C app. - 9°C
As a last resort, you can add up to 30%
of regular petrol to avoid paraffine de-
posits. However, this has negative ef-
fects on consumption rate and
performance.
8 agria-Two-Wheel Tractor 2500 Hydro
1
Before starting the engine, read the
operating instructions and note:
Warning
This symbol marks all paragraphs in
these operating instructions which affect
your safety. Pass all safety instructions
to other users and operators.
Due Use
The two-wheel tractor is a hand-
controlled automatic single-axle
machine which can power and/or pull
various implements approved by the
manufacturer. Areas of application are
for such as turning over the ground,
mowing grass and meadowland, snow
clearance and sweeping (due use).
Any other type of operation is
considered undue. The manufacturer is
not liable for any damage resulting from
undue use, for which the risk lies with
the user alone.
When the single-axle tractor/the tool
carrier/the multi-purpose machine is
used on public roads, the local national
road traffic rules must be observed, e.g.
reflectors, lights.
The single-axle tractor/the tool carrier/
The multi-purpose machine is not
intended for use with a trailer on public
roads or as as a tractor unit without
implements.
Due use includes compliance with
manufacturer’s instructions on
operation, maintenance and repair.
Any unauthorized changes to the two-
wheel tractor render manufacturer
liability null and void.
1. Safety Instructions
General Instructions on
Safety and Accident
Prevention
Basic Rule:
The standard accident prevention
regulations must be adhered to, as well
as all other generally accepted rules
governing operational safety,
occupational health and road traffic
regulations.
For drives on public roads, the latest
traffic code applies.
Accordingly, check the two-wheel tractor
for road and operational safety each
time you take up operation.
Only persons familiar with the two-wheel
tractor and instructed on the hazards of
operation are allowed to use, maintain
and repair the two-wheel tractor.
Young persons of 16 years or younger
may not operate the two-wheel tractor!
Only work in good light and visibility.
Operator’s clothes should fit tightly.
Avoid wearing loosely fitting clothes.
Wear solid shoes.
Note the warning and instruction signs
on the two-wheel tractor for safe
operation. Compliance is for your own
safety.
When transporting the two-wheel tractor
on vehicles or trailers outside the area
to be cultivated, ensure that the engine
is shut off.
agria-Two-Wheel Tractor 2500 Hydro 9
1
Careful with rotating tools – keep at a
safe distance!
Beware of coasting tools. Before you
start any maintenance or repair on them,
wait until tools have come to a complete
stop.
Foreign powered parts shear and crush!
Riding on the attachment during opera-
tion is not permitted.
Implements and weights affect the driv-
ing, steering, braking, and tip-over char-
acteristics of the two-wheel tractor.
Therefore, ensure steering and braking
functions are sufficient. Match operating
speed to conditions.
Do not change settings of governor. High
engine speed increases risk of
accidents.
Working Area and Danger
Zone
The user is liable to third parties work-
ing within the two-wheel tractor’s
working range.
Staying in the danger zone is not per-
mitted.
Check the immediate surroundings of
the two-wheel tractor before you start it.
Watch out for children and animals.
Before you start work, clear the area
from any foreign object. During opera-
tion, always watch out for further objects
and remove them in time.
For operation in enclosed areas, ensure
that a safety distance is kept to enclo-
sures to prevent damage to tools.
Operation and
Safety Devices
Before you start the engine
Become familiar with the devices and
operating elements and their functions.
Above all, learn how to turn the engine
off quickly and safely in an emergency
situation.
Ensure that all protective devices are
mounted and positioned to provide pro-
tection.
With no implement mounted, make sure
PTO-shaft is covered with the protec-
tive cap.
Starting the engine
Do not start engine in closed rooms. The
carbon monoxide contained in the ex-
haust fume is extremely toxic when in-
haled.
Before you start the engine set all oper-
ating elements to neutral or idling posi-
tion.
For starting the engine, do not step in
front of the two-wheel tractor and the
implement.
Do not use assist-starting liquids when
using electrical assist-starting devices
(jumper cable). Danger of explosion.
Operation
Never leave the operator’s position at
the steering handle while two-wheel
tractor is at work.
Never adjust the operating handles dur-
ing work – danger!
1. Safety Instructions
10 agria-Two-Wheel Tractor 2500 Hydro
1
For all works with the two-wheel tractor,
in particular for turning, the machine
operator must keep the distance to the
machine given by the steering handles.
Riding on the implement during opera-
tion or in transport is not permitted.
If clogging occurs in the implement, shut
off the engine and clean the implement
with an appropriate tool.
In case of damage to the two-wheel
tractor or to the implement, immediately
shut off the engine and have it repaired.
If steering causes problems, immedi-
ately bring the two-wheel tractor to a halt
and turn it off. Have the malfunction re-
moved without delay.
To prevent the two-wheel tractor from
sliding on slopes make sure it is secured
by another person using a bar or a rope.
This person must stay at a higher posi-
tion than the vehicle and at a safe dis-
tance from the attachment at work.
If possible, always work across the
slope.
End of Operation
Never leave the two-wheel tractor unat-
tended with the engine running.
Before you leave the two-wheel tractor,
shut off the engine. Then close fuel taps.
Secure two-wheel tractor against unau-
thorized use. If two-wheel tractor is
equipped with ignition key, remove the
key. For all other versions, remove spark
plug connector.
Implements
Only mount implements with the engine
and PTO shut off.
Always use appropriate tools and wear
gloves when changing implements and
parts thereof.
For mounting and dismounting imple-
ments bring stand into proper position
and ensure stability.
Secure two-wheel tractor and imple-
ments against rolling off (parking brake,
wheel chocks).
Beware of injuries while coupling imple-
ments. Work with particular care.
Hitch implements as specified and only
couple at specified points.
Secure two-wheel tractor and implement
against unauthorized use and rolling off
when you leave the machine. If neces-
sary, install transport or security devices
and secure.
Mowing Implement
Handle with care! Sharp blades of the
cutter bar may cause injuries! Remove
knife guards only for mowing and refit
immediately after work has finished.
For transport and storage always mount
the knife guards. Secure finger bars ad-
ditionally with tension springs.
Do not transport the dismounted cutter
bar without knife guards.
1. Safety Instructions
agria-Two-Wheel Tractor 2500 Hydro 11
1
When mounting and dismounting the
cutter bar, make sure all blades are pro-
tected by the knife guards.
To exchange the knife and to mount/dis-
mount the knife driver, make sure that
you turn screws away from cutting
blades.
For grinding the mowing knives, always
wear safety goggles and gloves.
Weights
Fit weights properly and at specified
points.
Maintenance
Never carry out any maintenance or
cleaning with the engine running.
Before you work on the engine, always
remove spark plug connector.
Check regularly and, if necessary, re-
place all protecting devices and tools
subject to wear and tear.
Replace damaged cutting tools.
Always wear safety gloves and use
proper tools when exchanging cutting
tools.
Do not carry out repairs like welding,
grinding, drilling, etc. on structural and
safety-relevant parts (e.g. hitch)!
Keep two-wheel tractor and implement
clean to avoid risk of fire.
Check nuts and bolts regularly for tight
fit and re-tighten, if necessary.
Ensure that you re-install all safety and
protective devices and adjust them prop-
erly after maintenance and cleaning.
Only use original agria spare parts. All
other commercial spare parts must cor-
respond to quality and technical require-
ments specified by agria.
Storage
It is not allowed to store the two-wheel
tractor in rooms with open heating.
Never park the two-wheel tractor in
closed rooms with fuel left in tank. Fuel
vapours are hazardous.
Engine, Fuel, and Oil
Never let the engine run in closed rooms.
Extreme danger of intoxication! For the
same reason, also replace damaged ex-
haust pipe immediately.
Be careful when handling fuel. Great
danger of fire! Never refill fuel close to
open fire, inflammable sparks or hot en-
gine parts. Do not refill fuel in closed
rooms. Do not smoke when refilling!
Refill only with the engine shut off and
cooled down.
1. Safety Instructions
12 agria-Two-Wheel Tractor 2500 Hydro
1
Do not spill any fuel, use a proper filling
device (e.g. funnel).
In case of fuel-spillage, pull the two-
wheel tractor away from the spillage
before you start the engine.
Make sure fuel is of specified quality.
Store fuel in approved cans only.
Liquids leaking under high pressure, e.g.
fuel, can penetrate the skin and cause
severe injuries. Immediately see a doc-
tor.
Store anti-corrosive agents and stabi-
lizing liquids out of reach of children. If
sickness and vomiting occur, see a doc-
tor. If fuel has contacted eyes, rinse
them thoroughly, avoid inhaling of va-
pours.
Read and observe enclosed instruc-
tions.
Before you dispose of opened and
seemingly empty pressurised tins (e.g.
of assist-starting liquids) make sure they
are completely empty. Empty them in
ventilated places safe from spark for-
mation or flames. If necessary, dispose
of tins in hazardous waste deposits.
Be careful when draining hot oil, dan-
ger of burns.
Make sure oil used is of specified qual-
ity. Storage is in approved cans only.
Dispose of oil, greases, and filters
seperately and properly.
Hydraulic System
The hydraulic system is subjected to
high pressure.
When connecting hydraulic motors, en-
sure the specified connection of the hy-
draulic hoses.
Hydraulic oil emerging under high pres-
sure may penetrate the skin and cause
serious injuries.
In case of injuries, immediately consult
a physician – risk of infections.
Prior to works on the hydraulic system,
render the latter pressureless and shut
down engine (specialized workshop).
When searching leakages, use suitable
aids considering the risk of injuries (spe-
cialized workshop).
Regularly check hydraulic hose lines for
damage and ageing and replace them,
if necessary.
Only use original agria hydraulic hoses.
Tyres and
Tyre Air Pressure
When working on wheels, make sure
two-wheel tractor is parked properly and
secured against rolling off.
Any repairs are to be carried out by
trained mechanics only and with the
appropriate tools.
Regularly check tyre air pressure. Ex-
cessive pressure may cause bursts.
1. Safety Instructions
agria-Two-Wheel Tractor 2500 Hydro 13
1
Use appropriate tyre air pressure for op-
eration with implements.
Re-tighten attachment bolts of drive-
wheels or check tightness when doing
maintenance work.
Electrical System and
Battery
When working on the electrical system,
make sure the battery is disconnected
(negative pole) (for two-wheel tractors
equipped with battery).
Make sure to connect battery properly
– first connect positive pole and then
negative pole. Disconnect in reverse or-
der.
Be careful with battery gases – explo-
sive!
Avoid spark discharge and open flames
near batteries.
Remove plastic cover (if included) to
recharge battery to prevent highly ex-
plosive gases from building up.
Be careful when handling battery acid!
Only use specified fuses. Stronger fuses
will destroy the electrical system – dan-
ger of fire.
Always cover positive pole with speci-
fied cover or terminal cap.
Persons having a pacemaker may not
touch live parts of the ignition system
when the engine is running.
1. Safety Instructions
Explanation of
Warning Signs
Before any clean-
ing, maintenance,
and repair work
shut off the engine
and pull ignition key.
Do not work without
protective covers
mounted. Before
starting the engine,
bring covers in
proper position.
With engine run-
ning, keep at a safe
distance from cut-
ting knife.
Do not touch mov-
ing machinery
parts. Wait until
they have come to
a complete stop.
With engine run-
ning, keep at a safe
distance.
Signs
When working with the
machine, wear individual
protective ear plugs.
Wear protective gloves.
Wear solid shoes.
14 agria-Two-Wheel Tractor 2500 Hydro
2
Dimensions two-wheel tractor:
A
min
A
max
B BF BH c
e
max
e
min
H HH + / - L
1
RH
min
RH
max
VH
L
VH
R
(e max)
(e min)
5.00-10 AS
20x8.00-10
21x11.00-8
5.00-12 AS
23x8.50-12
23x10.50-12
290
21°
18,5°
620
980
1000
17°
23°
890
(mm)
2010
870270
640 810 780 125 610
950 1120
930 1100
360 190
240
240
BR and S see track widths table page 16
2. Specifications
Machine
agria-Two-Wheel Tractor 2500 Hydro 15
A
min
A
max
B BF BH c
e
max
e
min
H HH + / - L2
RH
min
RH
max
VH
L
VH
R
Η
(e max)
Η
(e min)
5.00-10 AS
20x8.00-10
21x11.00-8
5.00-12 AS
23x8.50-12
23x10.50-12
870
620
240
640 810 780 125 610
890 240 23°
21°
18,5°
1655
995
1015
1165
1185
(mm)
17°270
190
290
360
980
1000
Dimensions tool carrier:
BR and S see track widths table page 16
2. Specifications
Machine
2
16 agria-Two-Wheel Tractor 2500 Hydro
2. Specifications
2
B
A S i A S i A S i A S i A S i A S i A S i
1
23x8.50-12 AS
660 445 230 880 665 450 720 505 290 940 725 510 780 565 350 1000 785 570 840 625 410 1060 845 630
2
23x10.50-12 AS 790 515 240 870 595 320 850 575 300 930 655 380 910 635 360 990 715 440 970 695 420 1050 775 500
3 5.00-12 AS
620 465 310 800 645 490 680 525 370 860 705 550 740 585 430 920 765 610 800 645 490 980 825 670
4 5.00-10 AS 610 480 350 760 630 500 670 540 410 820 690 560 730 600 470 880 750 620 790 660 530 940 810 680
5 20x8.00-10 R 700 510 320 790 600 410 760 570 380 850 660 470 820 630 440 910 720 530 880 690 500 970 780 590
6 21x11.00-8 Terra
790 515 240 860 585 310 850 575 300 920 645 370 910 635 360 980 705 430 970 695 420 1040 765 490
60 90 9030 6030
B V
+B1
V
+B2
V
+B3
V
+B4
V
+B5
V V
A S i A S i A A A A A A A
1
23x8.50-12 AS 1330 1115 450 1310 1430 1190 1364
#BEZUG!
2
23x10.50-12 AS 1320 1045 320 1300 1420 1180 1354 #BEZUG!
3 5.00-12 AS 1250 1095 490 1230 1350 1110 1284
4 5.00-10 AS 890 760 335 1210 1080 500 1020 1244 1094
5 20x8.00-10 R 1240 1050 410 1170
6 21x11.00-8 Terra 1319 1040 311
60 220
2500 Hydro
(mm)
(mm)
Wheel Combinations/ Track Widths
60 6030
30
90
90
220A
220 V
V
V
60
agria-Two-Wheel Tractor 2500 Hydro 17
2. Specifications
Tyre Tread Profile Use Item No.
5.00-10 field tyre general maintenance 0190 112
5.00-12 field tyre general maintenance 3490 411
20x8.00-10 grass tyre grass maintenance 3490 511
21x11.00-8 terra tyre
general maintenance
- Reduction of the
ground pressure, ideal
for use in biotopes and
wet fields
3490 611
23x8.5-12 wide-track field tyre general maintenance 5990 611
23x10.5-12 wide-track field tyre general maintenance 5990 711
10" traction cage wheels working on slopes 5917 011
12" traction cage wheels working on slopes 5917 021
2
Intermediate flanges, Use of the drive wheels
30= intermediate flange 30 mm 2516 011
60= intermediate flange 60 mm 2416 011
90 = track-width adjuster 90 mm 5519 031
V = intermediate flanges Vario 5916 211
220 = track-width adjuster 220 mm 5616 511
220A = track-width adjuster 220 mm with balancer
5519 011
18 agria-Two-Wheel Tractor 2500 Hydro
Transmission:.....................Hydrostat
Driving speeds:
Forward ............................. 0–6.0 km/h
Reverse............................ 0 - 4.0 km/h
PTO:....................................... 805 rpm
gear independent
at 3600 engine rpm
direction of rotation:
clockwise, looking on PTO,
constant in forward and reverse
PTO clutch .................electromagnetic
Steering: ............................................
completely hydraulic manual lever
steering
Steering handle:............ without tools
.................................height adjustable
side adjustable in each case 25°
swivelling 180°
Oil for transmission and hydrostat:
optionally:
hydraulic oil: ............. Mobil ATF 220
Bio-hydraulic oil:
Synthetic ester basis ................ HEES
Viscosity as per ISO................. VG 46
Purity class ........min. 16/13-ISO 4406
e.g.
ARAL: .......................... Vitam EHF 46
BP: ............................... Biohyd SE 46
ESSO:....................................... HE 46
FUCHS: .................... Plantohyd S 46
PANOLIN: .....................HLP Synth 46
Filling volume at
First filling: ........................... abt. 4.5 l
Oil change: ............................ abt.4.0 l
Oil filter: . Screw-type cartridge AW 14
Weights:
Empty weight: (with fuel tank filled up):
without with
drive-wheels 23x8.50-12
Vanguard
Recoil starter 190.8 kg 224 kg
Vanguard
Electric starter 198.8 kg 239 kg
Yanmar Electric starter 216,8 / 257 kg
Tyres:..................................optionally:
0190 112 ..................... 5.00-10 field tyre
3490 411 ..................... 5.00-12 field tyre
3490 511 ............20x 8.00-10 grass tyre
3490 611 .............. 21x11.00-8 terra tyre
5990 611 23x8.50-12 wide track field tyre
5990 711 23x10.50-12 wide track field tyre
partially track-width adjusters are
required, see page 16
Tyre air pressure at:
5.00-10..................................... 1.5 bar
5.00-12..................................... 1.5 bar
21x11.00- 8.............................. 0.8 bar
20x8.00- 10.............................. 0.8 bar
23x8.50-12............................... 1.3 bar
23x10.50-12............................. 1.3 bar
5917 011 .......traction cage wheels10"
.....................................for 5.00-10 AS
5917 021 .......traction cage wheels12"
for 5.00-12; 23x8.50-12; 23x10.50-12)
Drive-wheel application . see page 17
Drive-wheel attachment.. see page 28
2. Specifications
Machine
2
agria-Two-Wheel Tractor 2500 Hydro 19
2
Petrol Engine
Manufacturer: ........ Briggs & Stratton
Type: ................Vanguard OHV 13 HP
..................................... 245 437-0284
Version: ....................... Fan-air-cooled
1 cylinder-4-stroke
OHV engine (petrol)
Bore:........................................ 89 mm
Stroke:..................................... 63 mm
Cubic capacity: ....................390 ccm
Output: ............... 9.7 kW (13 SAE-hp)
at 3600 rpm
Max torque:...... 25.1 Nm at 2400 rpm
Spark plug: ................. Bosch FR8DC
Champion RC12YC
Spark plug gap 0.76 mm
Ignition:
Electr. magnetic ignition, contactless
ignition point is pre-set
Radio remote screened ............ as per
VDE 0879
Valve clearance (engine cold):
Intake .................................... 0.05 mm
Outlet .................................... 0.10 mm
Starter: ........ Recoil or electric starter
depending on version
Generator:.............................12V 16A
Battery: E-starter version .. 12V 20Ah
Flat plug fuse 15A
Fuel: ...................... Commercial petrol
min. octane number 90 RON
(refer to fuel recommendations)
Fuel tank capacity: ............. abt. 7.9 l
Fuel consumption:...........312 g/kWh
Air filter: .......... Dry filter element with
foamed preliminary filter
Carburetor: ........................ Horizontal
float carburetor
Rated speed: ......................3600 rpm
Top no-load speed: ............3800 rpm
Idling speed:.......................1750 rpm
Engine oil:
Filling quantity................approx. 0.96 l
Multi-grade oil
at ambient temperature -15° to +45°C:
SAE 10W-40 API-SC (or higher)
at ambient temperature -25° to +15°C:
SAE 10W-20 API-SC (or higher)
without OIL GARD
Noise level:
in accordance with EN 709 appendix
C, respectively EN 12733 appendix B:
Noise level at operator’s ear:
- without implement .... L
P
= 80,5 dB(A)
- Portal mowing drive.. L
P
= 86,2 dB(A)
- Rotary mower 80 ...... L
P
= 85,6 dB(A)
- Safety Mulcher 90 ... L
P
= 86,2 dB(A)
in accordance with 2000/14/EG,
appendix III, part B, chapter 32 lawn
mower:
Acoustic power level:
- without implement ..... L
P
= 99,1dB(A)
- Portal mowing drive L
P
= 106,3 dB(A)
- Rotary mower 80 .... L
P
= 105,6 dB(A)
- Safety Mulcher 90 . L
P
= 106,3 dB(A)
Vibration acceleration value:
In accordance with 2002/44/EC and EN 12733
on handlebar grip with: .......................
- Rotary mower 80 ........... a
hw
3,3 m/s
2
-Safety Mulcher 90 ........ a
hw
4,78 m/s
2
Operability on Slopes:
Engine is suited for use on slopes (with
oil level at “max” = upper level mark)
Continuous operation
.........................45° inclination (100%)
2. Specifications
Petrol Engine
2
20 agria-Two-Wheel Tractor 2500 Hydro
2. Specifications
Diesel Engine
2
Diesel Engine
Manufacturer: ........................ Yanmar
Type:
Electric starter version................ L100
Recoil starter version.................. L100
Version: ....................... Fan-air-cooled
1-cylinder-4-stroke diesel engine
Bore:........................................ 86 mm
Stroke:..................................... 70 mm
Cubic capacity: ................... 406 ccm
Output: ............... 7.4 kW at 3600 rpm
Max torque:......... 27 Nm at 1700 rpm
Injection pressure:................ 200 bar
Valve lash (engine cold)
Intake: ........................0.15 ± 0.02 mm
Outlet: ........................0.15 ± 0.02 mm
Starter: ........ Recoil or electric starter,
depending on version
Battery: ..............................12V 18Ah
Glass fuse............. 15A (30 x 6.5 mm)
Generator:............................12V 90W
Fuel: ....................... conventional fuel,
Min. cetane rating: ...........................45
(refer to fuel recommendations)
Fuel filter:
Coarse-mesh strainer ...... in filler neck
Fine-mesh strainer.............in fuel tank
drain hole
Fuel tank capacity: ........approx. 5.5 l
Air filter: .......... Dry filter element with
foamed preliminary filter
and cyclone pre-separator
Rated speed: ......................3600 rpm
Top no-load speed: ............3800 rpm
Idling speed:.......................1700 rpm
Lubrication: ....... Pressure lubrication
via gear pump
Full flow oil filter
Engine oil:
Filling quantity................approx. 1.65 l
Multi-grade oil
at ambient temperature -15° to +45°C:
SAE 10W-40 API-SC (or higher)
at ambient temperature -25° to +15°C:
SAE 5W-20 API-SC (or higher)
Noise level:
Noise level at operator’s ear...............
..............................................88 dB(A)
(In accordance with EN 709 and EN
1553)
Acoustic power level:........... 99 dB(A)
(In accordance with 84/538 EEC at
85% of rated engine speed)
Vibration acceleration value:
In accordance with 2002/44/EG and EN 12733
on handlebar grip with: .......................
-without mounted implement ..............
....................................... a
eq
4,77 m/s
2
-Rotary mower 80 .......... a
eq
5,35 m/s
2
-Safety mulcher 90 ........ a
eq
4,38 m/s
2
-Stone burier U80 .......... a
eq
5,90 m/s
2
Operability on Slopes:
Engine is suited for use on slopes
(oil level at “max” = upper mark)
Continuous operation possible
up to ..................20° inclination (37 %)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70

Agria 2500 Owner's manual

Category
Lawnmowers
Type
Owner's manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI