Agria 2500 Hydro Owner's manual

Before commissioning the machine, read operating

instructions and observe warnings and safety instructions.

Operating Instructions No.

998 783-B 03.10



Briggs & Stratton Petrol Engine

- Recoil Starter Version

- Electric Starter Version

Yanmar Diesel Engine

- Electric Starter Version

Two-Wheel TractorTwo-Wheel Tractor

Two-Wheel Tractor

2500 Hydro2500 Hydro

2500 Hydro

OriginalOriginal

Original

OperatingOperating

Operating

InstructionsInstructions

Instructions

2 agria-Two-Wheel Tractor 2500 Hydro

Please complete:

Machine Type No.:.......................

Identification No.:

..........................................................

Engine Type:..............................

Engine No.:................................

Date of Purchase:......................

For name plate, refer to

page 3/fig. A/4

For engine type and number, refer

to page 64/Fig. C/4 petrol engine

to page 68/Fig. D/17 diesel engine

Please state these data when order-

ing spare parts to avoid wrong deliv-

eries.

Only use original agria spare

parts!

Specifications, figures and dimen-

sions stated in these instructions are

not binding. No claims can be de-

rived from them. We reserve the right

for improvements without changing

these instructions.

This delivery comprises:



Operating instructions



Two-wheel tractor



Tool kit

Symbols

Warning – danger

Important information

Fuel

Fuel filter

Air filter

Choke

Forward

Reverse

Fast

Slow

Hydraulic system

PTO

Brake

Parking brake

Closed (locked)

Open (unlocked)

Clockwise

Lifting point

Grease gun

Lubrication point

 - Service

= contact your agria-workshop

see separate engine

operating instructions!

Symbols, Name Plate

agria-Two-Wheel Tractor 2500 Hydro 3

Fig. A

Fig. B

Designation of Parts

12

11

8

7

10

1

2

6

5

4

3

9

28 27 26

22

1

21

1110

3

31 30

24

23

32

4

29 25

33

4 agria-Two-Wheel Tractor 2500 Hydro

Fig. A:

1 Inspection and filling opening for transmission / hydraulic oil

3 Idle speed shifting mechanism (bypass)

4 Nameplate (machine identification no.)

10 Lower steering handle

11 Steering bar

21 Eye bolt with cap nut, top

22 PTO-shaft

23 Eye bolt with cap nut, bottom

24 Transmission oil drain screw

25 Clamping lever for axle adjustment

26 Brake drum

27 Wheel hub

28 Oil filter cartridge

29 Hook for loading Belt

30 Engine

31 Stand

32 Weight mounting device

33 Socket (version diesel engine)

Fig. B:

1 Safety circuit lever

2 Lever for lateral steering bar adjustment

3 Lever for hydraulic steering gear left

4 Lever for hydraulic steering gear right

5 Lever for stepless adjustment of driving speed and forward-reverse

driving

6 Speed adjusting lever

7 Eccentric lever for central brake

8 Operating mechanism for PTO clutch

9 Signal light for PTO

10 Ignition lock

11 Ratchet bolt for height adjustment of steering

12 Operating hour counter/speed counter

Designation of Parts

agria-Two-Wheel Tractor 2500 Hydro 5

Amount of Delivery ........................... 2

Recommendations

Lubricants ......................................... 6

Maintenance and Repair .................. 6

Fuel ................................................... 7

Designation of Parts

.......................................3, 64, 68

1. Safety Instructions....... 8 - 13

2. Specifications

Dimensions ...............................14, 15

Wheel combinations/Track Widths . 16

Machine ..........................................18

Vibration Acceleration Value........... 19

Petrol Engine .................................. 19

Diesel Engine ................................. 20

Noise Levels .............................19, 20

Operation on Slopes.................19, 20

3. Devices and Operating Elements

Engine............................................. 21

Speed Control Lever....................... 22

Ignition lock..................................... 22

Warning signal ................................ 22

Safety circuit ................................... 23

PTO circuit ...................................... 23

Setting the Driving Speed

and Direction .................................. 24

Coasting Operation......................... 24

Hydraulic Steering .......................... 25

Brake Central.................................. 25

Steering Handle.............................. 26

Steering Handle Swinging Buffer ... 27

Lifting points ................................... 27

Drive Wheels .................................. 28

Axle Adjustment ............................. 29

Mounting/Dismounting

Implements .....................................30

Implements .....................................31

Battery ............................................ 32

Fuse ................................................ 32

4. Commissioning and

Operation

Commissioning the Machine .. 33,

34

Starting the Petrol Engine . 35, 37

Shutting off the Petrol Engine .....

........................................... 36, 38

Starting the Diesel Engine....... 39

Shutting off the Diesel Engine. 40

Operation ................................. 41

Danger Zone............................ 41

Working on Slopes .................. 42

5. Maintenance

Petrol Engine .................... 43 - 44

Diesel Engine ................... 45 - 48

Battery ..................................... 49

Machine ............................ 50 - 53

- Transmission/Hydraulic Oil .... 50

- Drive Wheels ......................... 51

- Brake ..................................... 51

- Wheel motors ........................ 51

- Hydraulic Hoses .................... 51

- Safety Circuit ......................... 52

- Adjustments on Levers.......... 52

- Steering Tower....................... 53

- Guide Channel ...................... 53

General Maintenance .............. 53

Storage .................................... 54

Varnishes, Wear Parts...... 55

Electrical Wirings ......56 - 57

6. Troubleshooting.....58 - 61

Inspection and

Maintenance Chart........... 62

Maintenance Schedule ..

63, 66

Conformity Declaration ... 69

Note fold-out pages!

Fig. A + B............................. 3

Fig. C (Petrol Engine)....... 64

Fig. D (Diesel Engine) ...... 68

3

5

6

2

1

4

Index

6 agria-Two-Wheel Tractor 2500 Hydro

Lubricants and

Anti-Corrosive Agents

Use the specified lubricants for engine

and transmission (see “Specifications”).

We recommend using bio-lubricating

oil or bio-lubricating grease for “open”

lubricating points or nipples (as speci-

fied in the operating instructions).

We recommend using bio anti-corrosive

oil for preservation of machines and im-

plements (do not apply on painted ex-

ternal covers). Oil can be brushed or

sprayed on.

Anti-corrosive agents are kind to the

environment and degrade fast.

Using ecologically safe bio-lubricants

and bio-anti-corrosives, you contribute

to environmental protection and to the

wellbeing of humans, animals and

plants.

Maintenance and

Repair

The trained mechanics of your agria

workshop carry out expert maintenance

and repair.

You should only carry out major main-

tenance work and repairs on your own,

if you have the proper tools and knowl-

edge of machines and internal combus-

tion engines.

Do not hammer against the flywheel with

a hard object or metal tools as it might

crack and shatter in operation causing

injuries and damage. Only use suitable

tools for pulling the flywheel.

Recommendations

agria-Two-Wheel Tractor 2500 Hydro 7

Petrol Engine

This engine runs smoothly on commer-

cial unleaded regular and supergrade

petrol as well as on leaded supergrade

petrol.

Do not add oil to petrol.

If, for environmental reasons, you use

unleaded petrol, make sure the fuel is

drained completely when shutting down

the engine for more than 30 days. This

is to prevent resin residues from depos-

iting in the carburetor, fuel filter, and

tank. Or add a fuel stabilizer.

For further instructions refer to "Engine

Preservation".

Recommendations Fuel

Diesel Engine

This Diesel engine runs on conventional

Diesel fuel of a min. cetane rating of 45.

Do not use Diesel fuel oil substitutes,

they may be harmful to the fuel system.

Fuel should be free of water or dust.

Winter operation:

To ensure reliable winter operation use

“winter diesel fuel”, to be purchased at

filling stations.

At outside temperatures of below -

15°C , take the following additional pre-

cautions:

add commercial flow conditioners

or

add paraffine oil to depress diesel pour-

point:

Paraffine winter summer

oil: diesel diesel

fuel fuel

pour-point

50% app. -31°C app. -25°C

30% app. -26°C app. -15°C

10% app. -20°C app. - 9°C

As a last resort, you can add up to 30%

of regular petrol to avoid paraffine de-

posits. However, this has negative ef-

fects on consumption rate and

performance.

8 agria-Two-Wheel Tractor 2500 Hydro

1

Before starting the engine, read the

operating instructions and note:

Warning

This symbol marks all paragraphs in

these operating instructions which affect

your safety. Pass all safety instructions

to other users and operators.

Due Use

The two-wheel tractor is a hand-

controlled automatic single-axle

machine which can power and/or pull

various implements approved by the

manufacturer. Areas of application are

for such as turning over the ground,

mowing grass and meadowland, snow

clearance and sweeping (due use).

Any other type of operation is

considered undue. The manufacturer is

not liable for any damage resulting from

undue use, for which the risk lies with

the user alone.

When the single-axle tractor/the tool

carrier/the multi-purpose machine is

used on public roads, the local national

road traffic rules must be observed, e.g.

reflectors, lights.

The single-axle tractor/the tool carrier/

The multi-purpose machine is not

intended for use with a trailer on public

roads or as as a tractor unit without

implements.

Due use includes compliance with

manufacturer’s instructions on

operation, maintenance and repair.

Any unauthorized changes to the two-

wheel tractor render manufacturer

liability null and void.

1. Safety Instructions

General Instructions on

Safety and Accident

Prevention

Basic Rule:

The standard accident prevention

regulations must be adhered to, as well

as all other generally accepted rules

governing operational safety,

occupational health and road traffic

regulations.

For drives on public roads, the latest

traffic code applies.

Accordingly, check the two-wheel tractor

for road and operational safety each

time you take up operation.

Only persons familiar with the two-wheel

tractor and instructed on the hazards of

operation are allowed to use, maintain

and repair the two-wheel tractor.

Young persons of 16 years or younger

may not operate the two-wheel tractor!

Only work in good light and visibility.

Operator’s clothes should fit tightly.

Avoid wearing loosely fitting clothes.

Wear solid shoes.

Note the warning and instruction signs

on the two-wheel tractor for safe

operation. Compliance is for your own

safety.

When transporting the two-wheel tractor

on vehicles or trailers outside the area

to be cultivated, ensure that the engine

is shut off.

agria-Two-Wheel Tractor 2500 Hydro 9

1

Careful with rotating tools – keep at a

safe distance!

Beware of coasting tools. Before you

start any maintenance or repair on them,

wait until tools have come to a complete

stop.

Foreign powered parts shear and crush!

Riding on the attachment during opera-

tion is not permitted.

Implements and weights affect the driv-

ing, steering, braking, and tip-over char-

acteristics of the two-wheel tractor.

Therefore, ensure steering and braking

functions are sufficient. Match operating

speed to conditions.

Do not change settings of governor. High

engine speed increases risk of

accidents.

Working Area and Danger

Zone

The user is liable to third parties work-

ing within the two-wheel tractor’s

working range.

Staying in the danger zone is not per-

mitted.

Check the immediate surroundings of

the two-wheel tractor before you start it.

Watch out for children and animals.

Before you start work, clear the area

from any foreign object. During opera-

tion, always watch out for further objects

and remove them in time.

For operation in enclosed areas, ensure

that a safety distance is kept to enclo-

sures to prevent damage to tools.

Operation and

Safety Devices

Before you start the engine

Become familiar with the devices and

operating elements and their functions.

Above all, learn how to turn the engine

off quickly and safely in an emergency

situation.

Ensure that all protective devices are

mounted and positioned to provide pro-

tection.

With no implement mounted, make sure

PTO-shaft is covered with the protec-

tive cap.

Starting the engine

Do not start engine in closed rooms. The

carbon monoxide contained in the ex-

haust fume is extremely toxic when in-

haled.

Before you start the engine set all oper-

ating elements to neutral or idling posi-

tion.

For starting the engine, do not step in

front of the two-wheel tractor and the

implement.

Do not use assist-starting liquids when

using electrical assist-starting devices

(jumper cable). Danger of explosion.

Operation

Never leave the operator’s position at

the steering handle while two-wheel

tractor is at work.

Never adjust the operating handles dur-

ing work – danger!

1. Safety Instructions

10 agria-Two-Wheel Tractor 2500 Hydro

1

For all works with the two-wheel tractor,

in particular for turning, the machine

operator must keep the distance to the

machine given by the steering handles.

Riding on the implement during opera-

tion or in transport is not permitted.

If clogging occurs in the implement, shut

off the engine and clean the implement

with an appropriate tool.

In case of damage to the two-wheel

tractor or to the implement, immediately

shut off the engine and have it repaired.

If steering causes problems, immedi-

ately bring the two-wheel tractor to a halt

and turn it off. Have the malfunction re-

moved without delay.

To prevent the two-wheel tractor from

sliding on slopes make sure it is secured

by another person using a bar or a rope.

This person must stay at a higher posi-

tion than the vehicle and at a safe dis-

tance from the attachment at work.

If possible, always work across the

slope.

End of Operation

Never leave the two-wheel tractor unat-

tended with the engine running.

Before you leave the two-wheel tractor,

shut off the engine. Then close fuel taps.

Secure two-wheel tractor against unau-

thorized use. If two-wheel tractor is

equipped with ignition key, remove the

key. For all other versions, remove spark

plug connector.

Implements

Only mount implements with the engine

and PTO shut off.

Always use appropriate tools and wear

gloves when changing implements and

parts thereof.

For mounting and dismounting imple-

ments bring stand into proper position

and ensure stability.

Secure two-wheel tractor and imple-

ments against rolling off (parking brake,

wheel chocks).

Beware of injuries while coupling imple-

ments. Work with particular care.

Hitch implements as specified and only

couple at specified points.

Secure two-wheel tractor and implement

against unauthorized use and rolling off

when you leave the machine. If neces-

sary, install transport or security devices

and secure.

Mowing Implement

Handle with care! Sharp blades of the

cutter bar may cause injuries! Remove

knife guards only for mowing and refit

immediately after work has finished.

For transport and storage always mount

the knife guards. Secure finger bars ad-

ditionally with tension springs.

Do not transport the dismounted cutter

bar without knife guards.

1. Safety Instructions

agria-Two-Wheel Tractor 2500 Hydro 11

1

When mounting and dismounting the

cutter bar, make sure all blades are pro-

tected by the knife guards.

To exchange the knife and to mount/dis-

mount the knife driver, make sure that

you turn screws away from cutting

blades.

For grinding the mowing knives, always

wear safety goggles and gloves.

Weights

Fit weights properly and at specified

points.

Maintenance

Never carry out any maintenance or

cleaning with the engine running.

Before you work on the engine, always

remove spark plug connector.

Check regularly and, if necessary, re-

place all protecting devices and tools

subject to wear and tear.

Replace damaged cutting tools.

Always wear safety gloves and use

proper tools when exchanging cutting

tools.

Do not carry out repairs like welding,

grinding, drilling, etc. on structural and

safety-relevant parts (e.g. hitch)!

Keep two-wheel tractor and implement

clean to avoid risk of fire.

Check nuts and bolts regularly for tight

fit and re-tighten, if necessary.

Ensure that you re-install all safety and

protective devices and adjust them prop-

erly after maintenance and cleaning.

Only use original agria spare parts. All

other commercial spare parts must cor-

respond to quality and technical require-

ments specified by agria.

Storage

It is not allowed to store the two-wheel

tractor in rooms with open heating.

Never park the two-wheel tractor in

closed rooms with fuel left in tank. Fuel

vapours are hazardous.

Engine, Fuel, and Oil

Never let the engine run in closed rooms.

Extreme danger of intoxication! For the

same reason, also replace damaged ex-

haust pipe immediately.

Be careful when handling fuel. Great

danger of fire! Never refill fuel close to

open fire, inflammable sparks or hot en-

gine parts. Do not refill fuel in closed

rooms. Do not smoke when refilling!

Refill only with the engine shut off and

cooled down.

1. Safety Instructions

12 agria-Two-Wheel Tractor 2500 Hydro

1

Do not spill any fuel, use a proper filling

device (e.g. funnel).

In case of fuel-spillage, pull the two-

wheel tractor away from the spillage

before you start the engine.

Make sure fuel is of specified quality.

Store fuel in approved cans only.

Liquids leaking under high pressure, e.g.

fuel, can penetrate the skin and cause

severe injuries. Immediately see a doc-

tor.

Store anti-corrosive agents and stabi-

lizing liquids out of reach of children. If

sickness and vomiting occur, see a doc-

tor. If fuel has contacted eyes, rinse

them thoroughly, avoid inhaling of va-

pours.

Read and observe enclosed instruc-

tions.

Before you dispose of opened and

seemingly empty pressurised tins (e.g.

of assist-starting liquids) make sure they

are completely empty. Empty them in

ventilated places safe from spark for-

mation or flames. If necessary, dispose

of tins in hazardous waste deposits.

Be careful when draining hot oil, dan-

ger of burns.

Make sure oil used is of specified qual-

ity. Storage is in approved cans only.

Dispose of oil, greases, and filters

seperately and properly.

Hydraulic System

The hydraulic system is subjected to

high pressure.

When connecting hydraulic motors, en-

sure the specified connection of the hy-

draulic hoses.

Hydraulic oil emerging under high pres-

sure may penetrate the skin and cause

serious injuries.

In case of injuries, immediately consult

a physician – risk of infections.

Prior to works on the hydraulic system,

render the latter pressureless and shut

down engine (specialized workshop).

When searching leakages, use suitable

aids considering the risk of injuries (spe-

cialized workshop).

Regularly check hydraulic hose lines for

damage and ageing and replace them,

if necessary.

Only use original agria hydraulic hoses.

Tyres and

Tyre Air Pressure

When working on wheels, make sure

two-wheel tractor is parked properly and

secured against rolling off.

Any repairs are to be carried out by

trained mechanics only and with the

appropriate tools.

Regularly check tyre air pressure. Ex-

cessive pressure may cause bursts.

1. Safety Instructions

agria-Two-Wheel Tractor 2500 Hydro 13

1

Use appropriate tyre air pressure for op-

eration with implements.

Re-tighten attachment bolts of drive-

wheels or check tightness when doing

maintenance work.

Electrical System and

Battery

When working on the electrical system,

make sure the battery is disconnected

(negative pole) (for two-wheel tractors

equipped with battery).

Make sure to connect battery properly

– first connect positive pole and then

negative pole. Disconnect in reverse or-

der.

Be careful with battery gases – explo-

sive!

Avoid spark discharge and open flames

near batteries.

Remove plastic cover (if included) to

recharge battery to prevent highly ex-

plosive gases from building up.

Be careful when handling battery acid!

Only use specified fuses. Stronger fuses

will destroy the electrical system – dan-

ger of fire.

Always cover positive pole with speci-

fied cover or terminal cap.

Persons having a pacemaker may not

touch live parts of the ignition system

when the engine is running.

1. Safety Instructions

Explanation of

Warning Signs

Before any clean-

ing, maintenance,

and repair work

shut off the engine

and pull ignition key.

Do not work without

protective covers

mounted. Before

starting the engine,

bring covers in

proper position.

With engine run-

ning, keep at a safe

distance from cut-

ting knife.

Do not touch mov-

ing machinery

parts. Wait until

they have come to

a complete stop.

With engine run-

ning, keep at a safe

distance.

Signs

When working with the

machine, wear individual

protective ear plugs.

Wear protective gloves.

Wear solid shoes.

14 agria-Two-Wheel Tractor 2500 Hydro

2

Dimensions two-wheel tractor:

A

min

A

max

B BF BH c

e

max

e

min

H HH + / - L

1

RH

min

RH

max

VH

L

VH

R



(e max)



(e min)

5.00-10 AS

20x8.00-10

21x11.00-8

5.00-12 AS

23x8.50-12

23x10.50-12

290

21°

18,5°

620

980

1000

17°

23°

890

(mm)

2010

870270

640 810 780 125 610

950 1120

930 1100

360 190

240

BR and S see track widths table page 16

2. Specifications

Machine

agria-Two-Wheel Tractor 2500 Hydro 15

A

min

A

max

B BF BH c

e

max

e

min

H HH + / - L2

RH

min

RH

max

VH

L

VH

R

Η

(e max)

Η

(e min)

5.00-10 AS

20x8.00-10

21x11.00-8

5.00-12 AS

23x8.50-12

23x10.50-12

870

620

240

640 810 780 125 610

890 240 23°

21°

18,5°

1655

995

1015

1165

1185

(mm)

17°270

190

290

360

980

1000

Dimensions tool carrier:

BR and S see track widths table page 16

2. Specifications

Machine

2

16 agria-Two-Wheel Tractor 2500 Hydro

2. Specifications

2

B

A S i A S i A S i A S i A S i A S i A S i

1

23x8.50-12 AS

660 445 230 880 665 450 720 505 290 940 725 510 780 565 350 1000 785 570 840 625 410 1060 845 630

2

23x10.50-12 AS 790 515 240 870 595 320 850 575 300 930 655 380 910 635 360 990 715 440 970 695 420 1050 775 500

3 5.00-12 AS

620 465 310 800 645 490 680 525 370 860 705 550 740 585 430 920 765 610 800 645 490 980 825 670

4 5.00-10 AS 610 480 350 760 630 500 670 540 410 820 690 560 730 600 470 880 750 620 790 660 530 940 810 680

5 20x8.00-10 R 700 510 320 790 600 410 760 570 380 850 660 470 820 630 440 910 720 530 880 690 500 970 780 590

6 21x11.00-8 Terra

790 515 240 860 585 310 850 575 300 920 645 370 910 635 360 980 705 430 970 695 420 1040 765 490

60 90 9030 6030

B V

+B1

V

+B2

V

+B3

V

+B4

V

+B5

V V

A S i A S i A A A A A A A

1

23x8.50-12 AS 1330 1115 450 1310 1430 1190 1364

#BEZUG!

2

23x10.50-12 AS 1320 1045 320 1300 1420 1180 1354 #BEZUG!

3 5.00-12 AS 1250 1095 490 1230 1350 1110 1284

4 5.00-10 AS 890 760 335 1210 1080 500 1020 1244 1094

5 20x8.00-10 R 1240 1050 410 1170

6 21x11.00-8 Terra 1319 1040 311

60 220

2500 Hydro

(mm)

Wheel Combinations/ Track Widths

60 6030

30

90

220A

220 V

V

60

agria-Two-Wheel Tractor 2500 Hydro 17

2. Specifications

Tyre Tread Profile Use Item No.

5.00-10 field tyre general maintenance 0190 112

5.00-12 field tyre general maintenance 3490 411

20x8.00-10 grass tyre grass maintenance 3490 511

21x11.00-8 terra tyre

general maintenance

- Reduction of the

ground pressure, ideal

for use in biotopes and

wet fields

3490 611

23x8.5-12 wide-track field tyre general maintenance 5990 611

23x10.5-12 wide-track field tyre general maintenance 5990 711

10" traction cage wheels working on slopes 5917 011

12" traction cage wheels working on slopes 5917 021

2

Intermediate flanges, Use of the drive wheels

30= intermediate flange 30 mm 2516 011

60= intermediate flange 60 mm 2416 011

90 = track-width adjuster 90 mm 5519 031

V = intermediate flanges Vario 5916 211

220 = track-width adjuster 220 mm 5616 511

220A = track-width adjuster 220 mm with balancer

5519 011

18 agria-Two-Wheel Tractor 2500 Hydro

Transmission:.....................Hydrostat

Driving speeds:

Forward ............................. 0–6.0 km/h

Reverse............................ 0 - 4.0 km/h

PTO:....................................... 805 rpm

gear independent

at 3600 engine rpm

direction of rotation:

clockwise, looking on PTO,

constant in forward and reverse

PTO clutch .................electromagnetic

Steering: ............................................

completely hydraulic manual lever

steering

Steering handle:............ without tools

.................................height adjustable

side adjustable in each case 25°

swivelling 180°

Oil for transmission and hydrostat:

optionally:



hydraulic oil: ............. Mobil ATF 220



Bio-hydraulic oil:

Synthetic ester basis ................ HEES

Viscosity as per ISO................. VG 46

Purity class ........min. 16/13-ISO 4406

e.g.

ARAL: .......................... Vitam EHF 46

BP: ............................... Biohyd SE 46

ESSO:....................................... HE 46

FUCHS: .................... Plantohyd S 46

PANOLIN: .....................HLP Synth 46

Filling volume at

First filling: ........................... abt. 4.5 l

Oil change: ............................ abt.4.0 l

Oil filter: . Screw-type cartridge AW 14

Weights:

Empty weight: (with fuel tank filled up):

without with

drive-wheels 23x8.50-12

Vanguard

Recoil starter 190.8 kg 224 kg

Vanguard

Electric starter 198.8 kg 239 kg

Yanmar Electric starter 216,8 / 257 kg

Tyres:..................................optionally:

0190 112 ..................... 5.00-10 field tyre

3490 411 ..................... 5.00-12 field tyre

3490 511 ............20x 8.00-10 grass tyre

3490 611 .............. 21x11.00-8 terra tyre

5990 611 23x8.50-12 wide track field tyre

5990 711 23x10.50-12 wide track field tyre

partially track-width adjusters are

required, see page 16

Tyre air pressure at:

5.00-10..................................... 1.5 bar

5.00-12..................................... 1.5 bar

21x11.00- 8.............................. 0.8 bar

20x8.00- 10.............................. 0.8 bar

23x8.50-12............................... 1.3 bar

23x10.50-12............................. 1.3 bar

5917 011 .......traction cage wheels10"

.....................................for 5.00-10 AS

5917 021 .......traction cage wheels12"

for 5.00-12; 23x8.50-12; 23x10.50-12)

Drive-wheel application . see page 17

Drive-wheel attachment.. see page 28

2. Specifications

Machine

2

agria-Two-Wheel Tractor 2500 Hydro 19

2

Petrol Engine

Manufacturer: ........ Briggs & Stratton

Type: ................Vanguard OHV 13 HP

..................................... 245 437-0284

Version: ....................... Fan-air-cooled

1 cylinder-4-stroke

OHV engine (petrol)

Bore:........................................ 89 mm

Stroke:..................................... 63 mm

Cubic capacity: ....................390 ccm

Output: ............... 9.7 kW (13 SAE-hp)

at 3600 rpm

Max torque:...... 25.1 Nm at 2400 rpm

Spark plug: ................. Bosch FR8DC

Champion RC12YC

Spark plug gap 0.76 mm

Ignition:

Electr. magnetic ignition, contactless

ignition point is pre-set

Radio remote screened ............ as per

VDE 0879

Valve clearance (engine cold):

Intake .................................... 0.05 mm

Outlet .................................... 0.10 mm

Starter: ........ Recoil or electric starter

depending on version

Generator:.............................12V 16A

Battery: E-starter version .. 12V 20Ah

Flat plug fuse 15A

Fuel: ...................... Commercial petrol

min. octane number 90 RON

(refer to fuel recommendations)

Fuel tank capacity: ............. abt. 7.9 l

Fuel consumption:...........312 g/kWh

Air filter: .......... Dry filter element with

foamed preliminary filter

Carburetor: ........................ Horizontal

float carburetor

Rated speed: ......................3600 rpm

Top no-load speed: ............3800 rpm

Idling speed:.......................1750 rpm

Engine oil:

Filling quantity................approx. 0.96 l

Multi-grade oil

at ambient temperature -15° to +45°C:

SAE 10W-40 API-SC (or higher)

at ambient temperature -25° to +15°C:

SAE 10W-20 API-SC (or higher)

without OIL GARD

Noise level:



in accordance with EN 709 appendix

C, respectively EN 12733 appendix B:

Noise level at operator’s ear:

- without implement .... L

P

= 80,5 dB(A)

- Portal mowing drive.. L

P

= 86,2 dB(A)

- Rotary mower 80 ...... L

P

= 85,6 dB(A)

- Safety Mulcher 90 ... L

P

= 86,2 dB(A)



in accordance with 2000/14/EG,

appendix III, part B, chapter 32 lawn

mower:

Acoustic power level:

- without implement ..... L

P

= 99,1dB(A)

- Portal mowing drive L

P

= 106,3 dB(A)

- Rotary mower 80 .... L

P

= 105,6 dB(A)

- Safety Mulcher 90 . L

P

= 106,3 dB(A)

Vibration acceleration value:

In accordance with 2002/44/EC and EN 12733

on handlebar grip with: .......................

- Rotary mower 80 ........... a

hw

3,3 m/s

2

-Safety Mulcher 90 ........ a

hw

4,78 m/s

2

Operability on Slopes:

Engine is suited for use on slopes (with

oil level at “max” = upper level mark)

Continuous operation

.........................45° inclination (100%)

2. Specifications

Petrol Engine

2

20 agria-Two-Wheel Tractor 2500 Hydro

2. Specifications

Diesel Engine

2

Diesel Engine

Manufacturer: ........................ Yanmar

Type:

Electric starter version................ L100

Recoil starter version.................. L100

Version: ....................... Fan-air-cooled

1-cylinder-4-stroke diesel engine

Bore:........................................ 86 mm

Stroke:..................................... 70 mm

Cubic capacity: ................... 406 ccm

Output: ............... 7.4 kW at 3600 rpm

Max torque:......... 27 Nm at 1700 rpm

Injection pressure:................ 200 bar

Valve lash (engine cold)

Intake: ........................0.15 ± 0.02 mm

Outlet: ........................0.15 ± 0.02 mm

Starter: ........ Recoil or electric starter,

depending on version

Battery: ..............................12V 18Ah

Glass fuse............. 15A (30 x 6.5 mm)

Generator:............................12V 90W

Fuel: ....................... conventional fuel,

Min. cetane rating: ...........................45

(refer to fuel recommendations)

Fuel filter:

Coarse-mesh strainer ...... in filler neck

Fine-mesh strainer.............in fuel tank

drain hole

Fuel tank capacity: ........approx. 5.5 l

Air filter: .......... Dry filter element with

foamed preliminary filter

and cyclone pre-separator

Rated speed: ......................3600 rpm

Top no-load speed: ............3800 rpm

Idling speed:.......................1700 rpm

Lubrication: ....... Pressure lubrication

via gear pump

Full flow oil filter

Engine oil:

Filling quantity................approx. 1.65 l

Multi-grade oil

at ambient temperature -15° to +45°C:

SAE 10W-40 API-SC (or higher)

at ambient temperature -25° to +15°C:

SAE 5W-20 API-SC (or higher)

Noise level:

Noise level at operator’s ear...............

..............................................88 dB(A)

(In accordance with EN 709 and EN

1553)

Acoustic power level:........... 99 dB(A)

(In accordance with 84/538 EEC at

85% of rated engine speed)

Vibration acceleration value:

In accordance with 2002/44/EG and EN 12733

on handlebar grip with: .......................

-without mounted implement ..............

....................................... a

eq

4,77 m/s

2

-Rotary mower 80 .......... a

eq

5,35 m/s

2

-Safety mulcher 90 ........ a

eq

4,38 m/s

2

-Stone burier U80 .......... a

eq

5,90 m/s

2

Operability on Slopes:

Engine is suited for use on slopes

(oil level at “max” = upper mark)

Continuous operation possible

up to ..................20° inclination (37 %)

Page is loading ...

Agria 2500 Hydro Owner's manual

This manual is also suitable for

Agria 2500 Hydro Owner's manual

Related papers

Other documents