Ibiza Light LEDBAR6-RC Owner's manual

Page is loading ...

MANUAL - LEDBAR3/6/12-RC

2

LEDBAR RGBW 4-IN-1

WITH DMX & REMOTE CONTROL

INSTRUCTION MANUAL

IMPORTANT SAFETY INSTRUCTIONS AND DANGER WARNINGS

• Please read these instructions carefully, they include important information about the installation, usage and

maintenance of this product.

• Please keep this User Guide for future reference. If you sell the unit to another user, be sure that he also

receives this instruction booklet.

• Always make sure that you are connecting to the proper voltage, and that the line voltage you are connec-

ting to is not higher than that stated on the decal or rear panel of the xture.

• This product is intended for indoor use only!

• It is essential that the device is earthed. A qualied person must carry out the electric connection.

• To prevent risk of re or shock, do not expose xture to rain or moisture. Make sure there are no ammable

materials close to the unit while operating.

• The unit must be installed in a location with adequate ventilation, at least 20in (50cm) from adjacent sur-

faces. Be sure that no ventilation slots are blocked.

• Always disconnect from power source before servicing or replacing fuse and be sure to replace with same

fuse size and type.

• Secure xture to fastening device using a safety chain. Never carry the xture solely by its head. Use its

carrying handles.

• Maximum ambient temperature (Ta) is 104° F (40°C). Do not operate the xture at temperatures higher than

this.

• In the event of a serious operating problem, stop using the unit immediately. Never try to repair the unit

by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please contact the

nearest authorized technical assistance center. Always use the same type of spare parts.

• Don’t connect the device to a dimmer pack.

• Make sure the power cord is never crimped or damaged.

• Never disconnect the power cord by pulling or tugging on the cord.

• Avoid direct eye exposure to the light source while it is on.

• The product is for decorative purposes only and not suitable as a household room illumination.

• DISCONNECT DEVICE: Where the MAINS plug or an appliance coupler is used as the disconnect device, the

disconnect device shall remain readily operable.

SPECIFICATIONS:

Ref. LEDBAR3-RC LEDBAR6-RC LEDBAR12-RC

Input voltage AC100~240V 50/60Hz

Consumption 24W 48W 96W

LED source 3 x 8W RGBW 4-in-1 6 x 8W RGBW 4-in-1 12 x 8W RGBW 4-in-1

Beam angle 25°

Flash rate 0-20Hz

Fuse 0.5A 0.5A 1A

Control Signal DMX signal

Channel 8 / 4-1 / 4 / 3 / 2 Channels

Dimensions 265×87×129mm 605 x 145 x 120 mm 1150 x 145 x 120mm

Weight 1.2kg 2.5kg 3.5kg

EN

3

MANUAL - LEDBAR3/6/12-RC

SETUP

Disconnect the power cord before replacing a fuse and always replace with the same type fuse.

FUSE REPLACEMENT

• With a at head screwdriver wedge the fuse holder out of its housing.

• Remove the damaged fuse from its holder and replace with exactly the same type of fuse.

• Insert the fuse holder back in its place and reconnect power.

• The fuse is located inside this compartment. Remove using a at head screwdriver.

FIXTURE LINKING

You will need a serial data link to run light shows of one or more xtures using a DMX-512 controller or to run

synchronized shows on two or more xtures set to a master/slave operating mode. The combined number of

channels required by all xtures on a serial data link determines the number of xtures that the data link can

support.

Important: Fixtures on a serial/data link must be daisy chained in one single line. Maximum recommended

serial data link distance: 100 meters (1640 ft.) Maximum recommended number of xtures on a serial data link:

32 xtures

DATA CABLING

To link xtures together you must use data cables. If you choose to create your own cable, please use da-

ta-grade cables that can carry a high quality signal and are less prone to electromagnetic interference.

CABLE CONNECTORS

Cabling must have a male XLR connector on one end and a female XLR connector on the other end.

DMX connector conguration

Termination reduces signal errors. To avoid signal transmission problems and interference, it is always advisable

to connect a DMX signal terminator.

CAUTION

Do not allow contact between the common and the xture’s chassis ground. Grounding the common can cause

a ground loop, and your xture may perform erratically. Test cables with an ohm meter to check correct polarity

and to make sure the pins are not grounded or shorted to the shield or each other.

SETTING UP A DMX SERIAL DATA LINK

1. Connect the (male) 3 pin connector side of the DMX cable to the output (female) 3 pin connector of the

controller.

2. Connect the end of the cable coming from the controller which will have a (female) 3 pin connector to the

input connector of the next fixture consisting of a (male) 3 pin connector.

3. Then, proceed to connect from the output as stated above to the input of the following fixture and so on.

MASTER/SLAVE FIXTURE LINKING

1. Connect the (male) 3 pin connecter side of the DMX cable to the output (female) 3 pin connecter of the first

fixture.

2. Connect the end of the cable coming from the first fixture which will have a (female) 3 pin connecter to the

input connecter of the next fixture consisting of a (male) 3 pin connecter. Then, proceed to connect from

the output as stated above to the input of the following fixture and so on

3. Often, the set up for Master-Slave and Stand-alone operation requires that the first fixture in the chain be

initialized for this purpose via either settings in the control panel or DIP-switches. Secondarily, the fixtures

that follow may also require a slave setting. Please consult the '' Operating Instructions» section in this

manual for complete instructions for this type of setup and configuration.

INPUT

COMMON

DMX +

DMX-

Resistance 120 ohm

1/ 4w between pin 2

(DMX-) and pin 3

(DMX+) of the last

fixture.

MANUAL - LEDBAR3/6/12-RC

4

HOW TO CONTROL THE UNIT

Access control panel functions using the four panel buttons located directly un-

derneath the LCD Display.

Button Function

MENU Used to access the menu or to return to a previous menu option

UP Scrolls through menu options in ascending order

DOWN Scrolls through menu options in descending order

ENTER Used to select and store the current menu or option within a menu

When a menu function is selected, the display will show immediately the rst available option for the selected

menu function. To select a menu item, press <ENTER>.

Master mode: any unit cans work for master xture,

Slave mode: must be setting DMX address value for Slave.

DMX code setting: d1~d512

MANUAL SETTING MODE ON LED DISPLAY

Mode Programming Description

DMX mode Addr

8CH

d001-d512

4-1CH

4CH

3CH

2CH

Static colors Stat S 01-17 Static colors

Auto Auto Au 1-2 Auto program

Sound Mode Soun So 1-2 Sound Program

Speed SPEE SP 1-9 Speed

Mic Sensitivity SEnS SE 1-9 MIC sensitivity

Edit color Colo

r000-255 Red (0-100%)

g000-255 Green (0-100%)

b000-255 Blue (0-100%)

U000-255 White (0-100%)

Dimming dIMM dI1-dI 9 Master dimming

Silent scene SILE on/oFF Silent scene in Sound controlled program

Slave SLAV Slave Slave

Infrared InFr on/oFF Enable or Disable IR remote

DMX CHANNEL MODES

8-CH mode

CH1 0-255 Master dimming (0-100%)

CH2 0-255 Stroboscope (Rate 0-100%)

CH3 0-255 Red (0-100%)

CH4 0-255 Green (0-100%)

CH5 0-255 Blue (0-100%)

CH6 0-255 White (0-100%)

CH7

0-9 No function

10-19 Red

20-29 Green

30-39 Blue

5

MANUAL - LEDBAR3/6/12-RC

CH7

40-49 White

50-59 Yellow

60-69 Magenta

70-79 Cyan

80-89 Dark orange

90-99 Green yellow

100-109 Salmon

110-119 Turquoise

120-129 Light Green

130-139 Orange

140-149 Lavender

150-159 Light blue

160-169 Dark blue

170-255 Pink

CH8

0-9 No function

10-69 Color blending (rate)

70-129 Color change (rate)

130-189 Sound color blending (rate)

190-255 Sound color change (rate)

4-1 CH Mode

CH1 0-255 Master dimming (0-100%)

CH2 0-255 Stroboscope (Rate 0-100%)

CH3

0-9 No function

10-19 Red

20-29 Green

30-39 Blue

40-49 White

50-59 Yellow

60-69 Magenta

70-79 Cyan

80-89 Dark orange

90-99 Green yellow

100-109 Salmon

110-119 Turquoise

120-129 Light Green

130-139 Orange

140-149 Lavender

150-159 Light blue

160-169 Dark blue

170-255 Pink

CH4

0-9 No function

10-69w Color blending (rate)

70-129 Color change (rate)

130-189 Sound color blending (rate)

190-255 Sound color change (rate)

MANUAL - LEDBAR3/6/12-RC

6

4-CH Mode

CH1 0-255 Red (0-100%)

CH2 0-255 Green (0-100%)

CH3 0-255 Blue (0-100%)

CH4 0-255 White (0-100%)

3-CH Mode

CH1 0-255 Red (0-100%)

CH2 0-255 Green (0-100%)

CH3 0-255 Blue (0-100%)

2-CH Mode

CH1 0-255 Master dimming (0-100%)

CH2

0-9 No function

10-19 Red

20-29 Green

30-39 Blue

40-49 White

50-59 Yellow

60-69 Magenta

70-79 Cyan

80-89 Dark orange

90-99 Green yellow

100-109 Salmon

110-119 Turquoise

120-129 Light Green

130-139 Orange

140-149 Lavender

150-159 Light blue

160-169 Dark blue

170-255 Pink

IR REMOTE CONTROLLER

BLACK OUT Mode

1. Press BLACK OUT o existing modes, Press BLACK OUT to return the last modes.

AUTO Mode

1. Press <AUTO> on the IRC.

2. Press <+> or <–> to choose between the dierent AUTO programs.

SOUND Mode

1. Press <SOUND> on the IRC.

2. Press <+> or <–> to choose between the dierent SOUND programs.

STROBE Mode

1. Press <STROBE> on the IRC.

2. Press <+> or <–> to adjust the strobe rate.

3. Press <STROBE> again to turn o the strobe.

7

MANUAL - LEDBAR3/6/12-RC

MANUEL D'UTILISATION

SPEED Mode

1. Press <SPEED> on the IRC.

2. Press <+> or <–> to adjust the auto/sound program speed.

SENSITIVITY Mode

1. Press <SENSITIVITY> on the IRC.

2. Press <+> or <–> to adjust the microphone sensitivity value on the light.

DMX/% Mode

To enable DMX or disallow DMX on the product

Manual Mode

1. Press <MANUAL> on the IRC.

2. Press <R>, <G>, <B>and <W> to choose your color.

3. Press <+> or <–> to choose static colors.

FADE Mode

1. Press <FADE> on the IRC.

2. Press < FADE > again to turn o the FADE.

Number 1-9

1. Press digit <1> to <9> to change dierent brightness on the light.

Electric products must not be put into household waste. Please bring them to a recycling

centre. Ask your local authorities or your dealer about the way to proceed.

BARRE A LED RGBW 4-EN-1

AVEC DMX & TELECOMMANDE

CONSIGNES DE SECURITE

• Lisez attentivement ce manuel qui contient des informations importantes sur l’installation, l’utilisation et

l’entretien de cet appareil.

• Conservez le manuel pour référence ultérieure. Si l’appareil change un jour de propriétaire, assurez-vous que

le nouvel utilisateur est en possession du manuel.

• Assurez-vous que la tension secteur convient à cet appareil et qu’elle ne dépasse pas la tension d’alimenta-

tion indiqué sur la plaque signalétique de l’appareil.

• Uniquement pour utilisation à l’intérieur!

• L’appareil doit être impérativement relié à la terre.

• An d’éviter tout risque d’incendie ou de choc électrique, ne pas exposer cet appareil à la pluie ou à l’humi-

dité. Assurez-vous qu’aucun objet inammable ne se trouve à proximité de l’appareil pendant son fonction-

nement.

• Installez l’appareil à un endroit bien ventilé à une distance minimum de 50cm de toute surface. Assurez-vous

que les fentes de ventilation ne sont pas bloquées.

• Débranchez l’appareil du secteur avant toute manipulation ou entretien. Lorsque vous remplacez le fusible,

utilisez uniquement un fusible qui présente exactement les mêmes caractéristiques que l’ancien.

• Sécurisez l’appareil sur le dispositif de xation au moyen d’une chaîne. Ne portez jamais l’appareil en le te-

nant par le boîtier. Tenez-le par l’étrier.

• La température ambiante ne doit pas dépasser 40°C. Ne pas faire fonctionner l’appareil à des températures

supérieures.

• En cas de dysfonctionnement, arrêtez immédiatement l’appareil. N’essayez jamais de réparer l’appareil par

vous-même. Une réparation mal faite peut entraîner des dommages et des dysfonctionnements. Contactez

un service technique agréé. Utilisez uniquement des pièces détachées identiques aux pièces d’origine.

• Ne pas brancher l’appareil sur un variateur.

FR

Page is loading ...

21

HANDLEIDING - LEDBAR3/6/12-RC

CH4 0-255 Groen (0-100%)

CH5 0-255 Blauw (0-100%)

CH6 0-255 Wit (0-100%)

CH7

0-9 Geen functie

10-19 Rood

20-29 Groen

30-39 Blauw

CH7

40-49 Wite

50-59 Geel

60-69 Magenta

70-79 Cyan

80-89 Donker oranje

90-99 Geel-groen

100-109 Salmon

110-119 Turquoise

120-129 Licht Groen

130-139 Oranje

140-149 Lavender

150-159 Licht blauw

160-169 Donker blauw

170-255 Pink

CH8

0-9 Geen functie

10-69 Color blending (snelheid)

70-129 Color change (snelheid)

130-189 Sound color blending (snelheid)

190-255 Sound color change (snelheid)

4-1 kanaals modus

CH1 0-255 Master dimming (0-100%)

CH2 0-255 Stroboscoop (snelheid 0-100%)

CH3

0-9 Geen functie

10-19 Rood

20-29 Groen

30-39 Blauw

40-49 Wite

50-59 Geel

60-69 Magenta

70-79 Cyan

80-89 Donker oranje

90-99 Geel-groen

100-109 Salmon

110-119 Turquoise

120-129 Licht Groen

130-139 Oranje

140-149 Lavender

150-159 Licht blauw

160-169 Donker blauw

170-255 Pink

HANDLEIDING - LEDBAR3/6/12-RC

22

CH4

0-9 Geen functie

10-69w Color blending (snelheid)

70-129 Color change (snelheid)

130-189 Sound color blending (snelheid)

190-255 Sound color change (snelheid)

4-kanaals modus

CH1 0-255 Rood (0-100%)

CH2 0-255 Groen (0-100%)

CH3 0-255 Blauw (0-100%)

CH4 0-255 Wit (0-100%)

3-kanaals modus

CH1 0-255 Rood (0-100%)

CH2 0-255 Groen (0-100%)

CH3 0-255 Blauw (0-100%)

2-kanaals modus

CH1 0-255 Master dimming (0-100%)

CH2

0-9 Geen functie

10-19 Rood

20-29 Groen

30-39 Blauw

40-49 Wite

50-59 Geel

60-69 Magenta

70-79 Cyan

80-89 Donker oranje

90-99 Geel-groen

100-109 Salmon

110-119 Turquoise

120-129 Licht Groen

130-139 Oranje

140-149 Lavender

150-159 Licht blauw

160-169 Donker blauw

170-255 Pink

Page is loading ...

www.ibiza-light.com

42

Imported from China by LOTRONIC S.A.

Avenue Zénobe Gramme 9

B-1480 Saintes

LEDBAR3-RC

LEDBAR6-RC

LEDBAR12-RC

Ibiza Light LEDBAR6-RC Owner's manual

This manual is also suitable for

Ibiza Light LEDBAR6-RC Owner's manual

in other languages

Related papers

Other documents