Philips M555 Datasheet

www.philips.com/welcome

Extended user

documentation

Always there to help you

Register your product and get support at

M550

M555

Question?

Contact

Philips

1EN

Contents

1 Important safety instructions 3

2 Your phone 4

What is in the box 4

Overview of the phone 4

Overview of the base station 6

Display icons 6

3 Get started 7

Connect the base station and charger 7

Install the handset 7

Congure your phone (country

dependent) 8

Change the remote access PIN code 8

Charge the handset 9

Check the battery level 9

What is standby mode? 9

Check the signal strength 9

4 Calls 11

Make a call 11

Answer a call 11

End a call 11

Mute the microphone 12

Adjust the earpiece/speaker volume 12

Make a second call 12

Answer a second call 12

Switch between two calls 12

Make a conference call with the

external callers 12

5 Intercom and conference calls 13

Make a call to another handset 13

Transfer a call 13

Make a conference call 13

6 Text and numbers 15

Enter text and numbers 15

Switch between uppercase and

lowercase 15

7 Phonebook 16

View the phonebook 16

Search a record 16

Call from the phonebook 16

Access the phonebook during a call 16

Add a record 16

Edit a record 17

Delete a record 17

Delete all records 17

8 Call log 18

Call list type 18

View the call records 18

Save a call record to the phonebook 18

Return a call 18

Delete a call record 18

Delete all call records 19

9 Redial list 20

View the redial records 20

Redial a call 20

Save a call record to the phonebook 20

Delete a redial record 20

Delete all redial records 20

10 Phone settings 21

Sound settings 21

ECO+ mode 21

Name the handset 22

Set the date and time 22

Set the display language 22

11 Telephone answering machine 23

Turn the answering machine on or off 23

Set the answering machine language 23

Set the answer mode 23

Announcements 23

Incoming messages 24

Set the ring delay 25

Remote access 25

12 Services 27

Call list type 27

2 EN

Auto conference 27

Select the recall duration 27

Dial mode 27

Register additional handsets 28

Unregister the handsets 28

Restore default settings 28

13 Technical data 29

14 Notice 30

Declaration of conformity 30

Use GAP standard compliance 30

Compliance with EMF 30

Disposal of your old product and

batteries 30

15 Frequently asked questions 32

16 Appendix 34

Text and number input tables 34

17 Index 36

3EN

1 Important safety

instructions

Power requirements

• This product requires an electrical supply

of 100-240 volts AC. In case of power

failure, the communication can be lost.

• The voltage on the network is classied

as TNV-3 (Telecommunication Network

Voltages), as dened in the standard EN

60950.

Warning

• The Electrical network is classied as hazardous. The

only way to power down the charger is to unplug the

power supply from the electrical outlet. Ensure that the

electrical outlet is always easily accessible.

To avoid damage or malfunction

Caution

• Use only the power supply listed in the user

instructions.

• Use only the batteries listed in the user instructions.

• Risk of explosion if battery is replaced by an incorrect

type.

• Dispose of used batteries according to the instructions.

• Do not dispose of batteries in re.

• Always use the cables provided with the product.

• Do not allow the charging contacts or the battery to

come into contact with metal objects.

• Do not let small metal objects come into contact with

the product. This can deteriorate audio quality and

damage the product.

• Metallic objects may be retained if placed near or on

the handset receiver.

• Do not use the product in places where there are

explosive hazards.

• Do not open the handset, base station or charger as

you could be exposed to high voltages.

• For pluggable equipment, the socket-outlet shall

be installed near the equipment and shall be easily

accessible.

• Handsfree activation could suddenly increase the

volume in the earpiece to a very high level: make sure

the handset is not too close to your ear.

• This equipment is not designed to make emergency

calls when the power fails. An alternative has to be

made available to allow emergency calls.

• Do not allow the product to come into contact with

liquids.

• Do not use any cleaning agents containing alcohol,

ammonia, benzene, or abrasives as these may harm

the set.

• Do not expose the phone to excessive heat caused by

heating equipment or direct sunlight.

• Do not drop your phone or allow objects to fall on

your phone.

• Active mobile phones in the vicinity may cause

interference.

About operating and storage temperatures

• Operate in a place where temperature is

always between 0°C to +40°C (up to 90%

relative humidity).

• Store in a place where temperature is

always between -20°C and +45°C (up to

95% relative humidity).

• Battery life may be shorter in low

temperature conditions.

4 EN

2 Your phone

Congratulations on your purchase and welcome

to Philips!

To fully benet from the support that Philips

offers, register your product at www.philips.

com/welcome.

What is in the box

Base station (with two connectors)

Handset

Charger (with one connector)

Power adapter

Line cord*

Guarantee

Short user manual

Note

• * In some countries, you have to connect the line

adapter to the line cord, then plug the line cord to the

telephone socket.

Overview of the phone

4XLFNVWDUWJXLGH

g

f

e

d

c

b

a

n

m

l

k

j

i

h

5EN

a Earpiece

b REDIAL/C

• Delete text or digits.

• Cancel operation.

• Access the redial list.

c

• End the call.

• Exit the menu/operation.

• Press and hold to switch the handset

on or off.

d

• Scroll down on the menu.

• Decrease the earpiece/speaker volume.

• Access the call log in standby mode.

e

• Press and hold to enter a pause.

• Switch to upper/lower case during

editing.

f

Mute or unmute the microphone.

g Microphone

h Battery door opening

i

• Turn the speaker phone is on/off.

• Make and receive calls through the

speaker.

o

p

q

j

• Press and hold to make an intercom

call (for multi-handset versions only).

• Set the dial mode (pulse mode or

temporary tone mode).

k

• Press to enter a space during text

editing.

• Press and hold to lock/unlock the

keypad in standby mode.

l

• Make and receive calls.

• Recall key

m MENU/OK

• Access the main menu.

• Conrm selection.

• Enter the options menu.

• Select the function displayed on the

handset screen directly above the key.

n

• Scroll up on the menu.

• Increase the earpiece/speaker volume.

• Access the phonebook in standby

mode.

o Loudspeaker

p LED indicator

• Off: no new event

• On: for two seconds when putting the

handset on the base station.

• Flashing: new miss calls/new messages

on answering machine, new voice mails,

new text messages (if applicable)

• Flashing quickly: new incoming call

q Handset back cover

6 EN

Overview of the base station

a

• Find handsets.

• Press and hold to enter registration

mode.

Display icons

In standby mode, the icons shown on the main

screen tell you what features are available on

your handset.

Icon Descriptions

When the handset is off the base

station/charger, the bars indicate the

battery level (from full to low).

When the handset is on the base

station/charger, the bars keep scrolling

until charging is complete.

The empty battery icon ashes and

you hear an alert tone.

The battery is low and needs

recharging.

The number of bar indicates the

connection status between the

handset and base station. The more

bars are shown, the better the signal

or the connection is.

It remains steadily on when browsing

answered incoming calls in the call log.

It indicates an outgoing call in the

redial list.

a

It ashes when there is a new missed

call or when browsing the unread

missed calls in call log.

It remains steadily on when browsing

the read missed calls in call log.

It ashes when receiving incoming call.

It remains steadily on during a call.

The speaker is on.

The ringer is off.

Answering machine: it ashes when

there is a new message or when

the memory is full. It displays when

the telephone answering machine is

turned on.

It ashes when there is a new voice

message.

It remains steadily on when the voice

messages are already viewed in the

call log.

The icon is not shown when there is

no voice message.

This feature is network dependent.

/

It is displayed when you scroll up/

down a list/increase and decrease the

volume.

There are more digits on the right.

Press REDIAL/C to read.

ECO+ The ECO+ mode is activated.

7EN

3 Get started

Caution

• Make sure that you have read the safety instructions in

the 'Important safety instructions' section before you

connect and install your handset.

Connect the base station and

charger

Warning

• Risk of product damage! Ensure that the power supply

voltage corresponds to the voltage printed on the back

or the underside of the phone.

• Use only the supplied power adapter to charge the

batteries.

Note

• If you subscribe to the digital subscriber line (DSL) high

speed internet service through your telephone line,

ensure you install a DSL lter between the telephone

line cord and the power socket. The lter prevents

noise and caller ID problems caused by the DSL

interference. For more information on the DSL lters,

contact your DSL service provider.

• The type plate is located on the bottom of the base

station.

1 Connect each end of the power adapter

to:

• the DC input jack at the bottom of the

base station;

• the power socket on the wall.

2 Connect each end of the line cord to:

• the telephone socket at the bottom of

the base station;

• the telephone socket on the wall.

3 Connect each end of the power adapter

to (for multi handset version only):

• the DC input jack at the bottom of the

extra handset charger.

• the power socket on the wall.

Install the handset

The batteries are pre-installed in the handset.

Pull the battery tape off from the battery door

before charging.

8 EN

Caution

• Risk of explosion! Keep batteries away from heat,

sunshine or re. Never discard batteries in re.

• Use only the supplied batteries.

• Risk of decreased battery life! Never mix different

brands or types of batteries.

Note

• Charge the batteries for 8 hours before rst use.

• If the handset becomes warm when the batteries are

being charged, it is normal.

Warning

• Check the battery polarity when inserting in the

battery compartment. Incorrect polarity may damage

the product.

Congure your phone

(country dependent)

1 When using your phone for the rst time,

you see a welcome message.

2 Press MENU/OK.

Set the country/language

Select your country/language, then press

MENU/OK to conrm.

» The country/language setting is saved.

Note

• The country/language setting option is country

dependent. If no welcome message is displayed, it

means the country/language setting is preset for your

country. Then you can set the date and time.

To re-set the language, see the following steps.

1 Select [Phone setup] > [Language], then

press MENU/OK to conrm.

2 Select a language, then press MENU/OK

to conrm.

» The setting is saved.

Set the date and time

Tip

• To set the date and time later, press REDIAL/C to skip

this setting.

1 Press MENU/OK.

2 Select [Phone setup] > [Date & time],

then press MENU/OK to conrm.

3 Press the numeric buttons to enter the

date, then press MENU/OK to conrm.

» The time setting menu is displayed on

the handset.

4 Press the numeric buttons to enter the

time.

• If the time is in 12-hour format, press

/ to select [am] or [pm] (Country

dependent).

5 Press MENU/OK to conrm.

Change the remote access

PIN code

Note

• The default answering machine remote access PIN

code is 0000 and it is important to change it to ensure

the security.

9EN

1 Press MENU/OK.

2 Select [Answ. Machine] > [Remote

access] > [Change PIN], then press

MENU/OK to conrm.

3 Enter the old PIN/passcode, then press

MENU/OK to conrm.

4 Enter the new PIN/passcode, then press

MENU/OK to conrm.

5 Enter the new PIN/passcode again, then

press MENU/OK to conrm.

» The setting is saved.

Charge the handset

Charge your handset by docking it in either

direction. When the handset is placed correctly

on the base station, you hear a docking tone

(see 'Set the docking tone' on page 21). The

LED at the back of the handset ashes once.

» The handset starts charging.

Note

• Charge the batteries for 8 hours before rst use.

• If the handset becomes warm when the batteries are

being charged, it is normal.

• Over time, capacity of batteries decreases. This is a

normal battery behavior.

Your phone is now ready to use.

Check the battery level

The battery icon displays the current battery

level.

When the handset is off the

base station, the bars indicate the

battery level (full, medium and

low).

The empty battery icon ashes.

The battery is low and needs

recharging.

If you are on the phone, you hear warning

tones when the batteries are almost empty.

The handset turns off when the batteries are

completely empty.

What is standby mode?

Your phone is in standby mode when it is idle.

The standby screen displays the handset name,

handset number, date and time.

Check the signal strength

The number of bars indicates

the connection status between

the handset and base station. The

more bars are shown, the better

the connection is.

• Make sure the handset is connected to the

base station before you make or receive

calls and carry out the phone functions

and features.

• If you hear warning tones when you are

on the phone, the handset is almost out

of battery or the handset is out of range.

Charge the battery or move the handset

nearer to the base station.

10 EN

Note

• When ECO+ is on, the signal strength is not displayed.

11EN

4 Calls

Note

• When the power fails, the phone cannot access

emergency services.

Tip

• Check the signal strength before you make a call or

when you are in a call (see 'Check the signal strength'

on page 9).

Make a call

You can make a call in these ways:

• Normal call

• Predial call

You can also make a call from the redial list (see

'Redial a call' on page 20), phonebook list (see

'Call from the phonebook' on page 16) and call

log (see 'Return a call' on page 18).

Normal call

1 Press or .

2 Dial the phone number.

» The number is dialed out.

» The duration of your current call is

displayed.

Predial call

1 Dial the phone number

• To erase a digit, press REDIAL/C.

• To erase all digits, press and hold

REDIAL/C.

• To enter a pause, press and hold .

2 Press or to dial out the call.

Note

• The call timer displays the talk time of your current call.

• If you hear warning tones, the phone is almost out of

battery or out of range. Charge the battery or move

the phone close to the base station.

Answer a call

When the phone rings, you can select from the

following options:

• press or to answer the call.

• press REDIAL/C to turn off the ringer of

this call.

Warning

• When the handset rings or when the handsfree is

activated, keep the handset away from your ear to

avoid ear damage.

Note

• If you have subscribed for a caller ID service with

the service provider, you will see the caller number

displayed on the handset. If the number is saved in the

phonebook, the name will be displayed.

Tip

• When there is a missed call, a notication message

appears.

End a call

You can end a call in these ways:

• Press ;

• Place the handset to the base station

or charging cradle.

12 EN

Mute the microphone

1 Press during a call.

» The handset displays [Mute on].

» The caller cannot hear you, but you

can still hear his voice.

2 Press again to unmute the microphone.

» You can now communicate with the

caller.

Adjust the earpiece/speaker

volume

Press / to adjust the volume during a call.

» The earpiece/speaker volume is

adjusted and the phone is back to the

call screen.

Make a second call

Note

• This service is network dependent.

1 Press during a call.

» The rst call is put on hold.

2 Dial the second number.

» The number displayed on the screen is

dialed out.

Answer a second call

Note

• This service is network dependent.

When there is a periodical beep to notify you

of an incoming call, you can answer the call in

these ways:

1 Press and to answer the call.

» The rst call is put on hold, and you

are now connected to the second call.

2 Press and to end the current call and

answer the rst call.

Switch between two calls

Press and .

» The current call is put on hold, and you

are now connected to the other call.

Note

• This feature is country dependent.

Make a conference call with

the external callers

Note

• This service is network and country dependent. Check

with the service provider for additional charges.

When you are connected to two calls, press

, then .

» The two calls are combined and a

conference call is established.

13EN

5 Intercom and

conference calls

Note

• This feature is available for multi- handset versions only.

An intercom call is a call to another handset

that shares the same base station. A conference

call involves a conversation between you,

another handset user and the outside callers.

Make a call to another

handset

Note

• If the base station only has 2 registered handsets, press

and hold

to make a call to another handset.

1 Press and hold .

» The handsets available for intercom are

displayed.

2 Select a handset number, then press

MENU/OK to conrm.

» The selected handset rings.

3 Press on the selected handset.

» The intercom is established.

4 Press REDIAL/C or to cancel or end

the intercom call.

Note

• If the selected handset is busy, [Busy] is displayed on

the handset screen.

While you are on the phone

You can go from one handset to another during

a call:

1 Press and hold .

» The current caller is put on hold.

2 Select a handset number, then press

MENU/OK to conrm.

» Wait for the other side to answer your

call.

Switch between calls

Press and hold to switch between the

outside call and the intercom call.

Transfer a call

1 Press and hold during a call.

» The handsets available for intercom are

displayed.

2 Select a handset number, then press

MENU/OK to conrm.

3 Press when the other side answers

your call.

» The call is now transferred to the

selected handset.

Make a conference call

A 3-way conference call is between you,

another handset user and the outside callers. It

requires two handsets to share the same base

station.

During an external call

1 Press and hold to initiate an internal call.

» The external caller is put on hold.

14 EN

» For multi-handset versions, The

handsets available for intercom are

displayed. Then go to step 2.

» For two-handset versions, the other

handset rings. Then go to step 3.

2 Select or enter a handset number, then

press MENU/OK to conrm.

» The selected handset rings.

3 Press on the selected handset.

» The intercom is established.

4 Press MENU/OK.

» You are now in a 3-way conference

call with an external call and a selected

handset.

5 Press to end the conference call.

During the conference call

• Press REDIAL/C or press and hold to

put the external call on hold and go back

to the internal call.

» The external call is put on hold.

• Press MENU/OK to establish the

conference call again.

Note

• If a handset hangs up during the conference call, the

other handset remains connected to the external call.

15EN

6 Text and

numbers

You can enter text and numbers for handset

name, phonebook records, and other menu

items.

Enter text and numbers

1 Press once or several times on the

alphanumeric key to enter the selected

character.

2 Press REDIAL/C to delete a character.

Press and hold REDIAL/C to delete all

characters. Press

and to move the

cursor left and right.

3 Press to add a space.

Note

• For information on key mapping of characters and

numbers, see the chapter 'Appendix'.

Switch between uppercase

and lowercase

By default, the rst letter of each word in a

sentence is uppercase and the rest is lowercase.

Press and hold

to switch between the

uppercase and lowercase letters.

16 EN

7 Phonebook

This phone has a phonebook that stores up

to 100 records. You can access the phonebook

from the handset. Each record can have a name

up to 14 characters long and a number up to

24 digits long.

There are 2 direct access memories (keys

and ). Depending on your country, keys

and are preset to the voice mail number

and information service number of your service

provider respectively. When you press and hold

on the key in standby mode , the saved phone

number is dialed automatically.

View the phonebook

Note

• You can view the phonebook on one handset only

each time.

1 Press or press MENU/OK >

[Phonebook] > [View] to access the

phonebook list.

2 Select a contact and view the available

information.

Search a record

You can search the phonebook records in these

ways:

• Scroll the contacts list.

• Enter the rst character of the contact.

Scroll the contact list

1 Press or press MENU/OK >

[Phonebook] > [View] to access the

phonebook list.

2 Press and to scroll through the

phonebook list.

Enter the rst character of a contact

1 Press or press MENU/OK >

[Phonebook] > [View] to access the

phonebook list.

2 Press the alphanumerical key that matches

the character.

» The rst record that starts with this

character is displayed.

Call from the phonebook

1 Press or press MENU/OK >

[Phonebook] > [View] to access the

phonebook list.

2 Select a contact in the phonebook list.

3 Press to make the call.

Access the phonebook during

a call

Press MENU/OK, select the contact, then press

MENU/OK to view the number.

Add a record

Note

• If your phonebook memory is full, the handset displays

a notication message. Delete some records to add

new ones.

1 Press MENU/OK.

2 Select [Phonebook] > [Add new].

3 Enter the name, then press MENU/OK to

conrm.

4 Enter the number, then press MENU/OK

to conrm

» Your new record is saved.

17EN

Tip

• Press and hold to insert a pause.

Note

• The phonebook overwrites the old number with the

new number.

Tip

• Press once or several times on the alphanumeric key to

enter the selected character.

• Press REDIAL/C to delete the character. Press and

to move the cursor left and right.

Edit a record

1 Press MENU/OK.

2 Select [Phonebook] > [Edit].

3 Select a contact, then press MENU/OK to

conrm.

4 Edit the name, then press MENU/OK to

conrm.

5 Edit the number, then press MENU/OK to

conrm.

» The record is saved.

Delete a record

1 Press MENU/OK.

2 Select [Phonebook] > [Delete].

3 Select a contact, then press MENU/OK to

conrm.

» The handset displays a conrmation

request.

4 Press MENU/OK to conrm.

» The record is deleted.

Delete all records

1 Press MENU/OK.

2 Select [Phonebook] > [Delete all].

» The handset displays a conrmation

request.

3 Press MENU/OK to conrm.

» All records (except the 2 direct access

memory records) are deleted.

18 EN

8 Call log

The call log stores the call history of all missed

or received calls. The incoming call history

includes the name and number of the caller,

call time and date. This feature is available if you

have registered to the caller ID service with

your service provider.

Your phone can store up to 50 call records. The

call log icon on the handset ashes to remind

you of any unanswered calls. If the caller allows

the display of his identity, you can view his

name or number. The call records are displayed

in chronological order with the most recent

received call at the top of the list.

Note

• Make sure that the number in the call list is valid before

you can call back directly from the call list.

The icons shown on the screen tell you

whether they are missed/received calls.

Icons Description

It remains steadily on when browsing

answered incoming calls in the call log.

It ashes when there is a new missed

call or when browsing the unread

missed calls in call log.

It remains steadily on when browsing

the read missed calls in call log.

Call list type

You can set if you can see all calls or missed

calls from the call log.

Select the call list type

1 Press MENU/OK.

2 Select [Services] > [Call list type], then

press MENU/OK to conrm.

3 Select an option, then press MENU/OK to

conrm.

View the call records

1 Press .

» The incoming call log is displayed.

2 Select a record, then press MENU/OK

and [View] select for more available

information.

Save a call record to the

phonebook

1 Press .

» The incoming call log is displayed.

2 Select a record, then press MENU/OK to

conrm.

3 Select [Save number], then press MENU/

OK to conrm.

4 Enter and edit the name, then press

MENU/OK to conrm.

5 Enter and edit the number, then press

MENU/OK to conrm.

» The record is saved.

Return a call

1 Press .

2 Select a record on the list.

3 Press to make the call.

Delete a call record

1 Press .

» The incoming call log is displayed.

Page is loading ...

Philips M555 Datasheet

This manual is also suitable for

Philips M555 Datasheet

Related papers

Other documents