Evoqua W3T350215 User manual

Brand: Evoqua

Model: W3T350215

Type: User manual

This manual is also suitable for

WALLACE & TIERNAN DEPOLOX 5 Series

INSTRUCTION MANUAL

DEPOLOX® 5 E

WALLACE & TIERNAN

FLOW CELL

DEPOLOX® 5 E flow cell

In some countries, DEPOLOX, OSEC, Barrier, Chem-Ad and Wallace & Tiernan are trademarks of Evoqua, its subsidiaries or

affiliated companies. No part of this document may be reproduced in any form (printed, photocopy, microfilm, or any other

procedure) or saved, processed, copied, or distributed using electronic data systems - without the express prior written con-

sent of Evoqua Water Technologies GmbH.

All information in this document is considered reliable and corresponds to the generally applicable technical standards. Evo-

qua assumes no responsibility for the completeness of this information. Users are responsible for making sure that the pro-

duct is suitable for specific applications. Evoqua assumes no liability for specific or indirect damage or consequential

damage arising from the sale, resale or misuse of its products.

NOTICE

Translation of the original instruction.

DEPOLOX® 5 E flow cell Contents

Contents

1. Introduction ............................................................................... 5

1.1 Target groups ..........................................................................................................5

1.2 Conventions.............................................................................................................5

2. Safety......................................................................................... 6

2.1 Intended use............................................................................................................6

2.2 General safety instructions .....................................................................................6

2.3 Specific operating phases........................................................................................7

2.4 Warranty conditions................................................................................................7

2.5 Exclusion of liability.................................................................................................7

3. Description................................................................................. 8

3.1 Versions...................................................................................................................8

3.2 Configuration options............................................................................................11

3.3 Spare Parts/extensions..........................................................................................12

3.4 Optional accessories..............................................................................................12

3.5 Design and functions.............................................................................................12

3.6 Sensors ..................................................................................................................14

3.7 Technical Data .......................................................................................................15

4. Installation ............................................................................... 18

4.1 Scope of supply .....................................................................................................18

4.2 Transport and storage...........................................................................................18

4.3 Ambient conditions ...............................................................................................19

4.4 Mechanical installation .........................................................................................19

4.5 Installation of the module.....................................................................................20

4.6 Removing and fitting the housing cover ...............................................................23

4.7 Installing the optional strainer ..............................................................................23

4.8 Connecting the sample water inlet .......................................................................23

4.9 Connecting the sample water outlet.....................................................................24

4.10 Sample water take-off options..............................................................................25

4.11 Installing the fine filter ..........................................................................................27

4.12 Removing the felt ring...........................................................................................28

4.13 Removing and replacing transport caps................................................................28

4.14 Filling electrode cleaning sand ..............................................................................29

4.15 Connecting sensors with DFMe electronics module ...........................................30

4.16 Fitting the sens (optional) .....................................................................................31

4.17 Installing calibration aids.......................................................................................32

4.18 Commissioning ......................................................................................................32

4.19 Shutting down .......................................................................................................33

4.20 Recommissioning ..................................................................................................33

4.21 Retrofit kits............................................................................................................34

Contents DEPOLOX® 5 E flow cell

5. Maintenance............................................................................ 37

5.1 Maintenance intervals .......................................................................................... 37

5.2 Maintenance parts kits ......................................................................................... 37

5.3 Checking for leakage............................................................................................. 37

5.4 Checking electrode cleaning sand......................................................................... 37

5.5 Checking electrolyte solution level....................................................................... 38

5.6 Checking diaphragms............................................................................................ 38

5.7 Replacing or cleaning electrode cleaning sand, electrolyte solution,

reference electrode and diaphragms .................................................................. 38

5.8 Cleaning or replacing the fine filter ...................................................................... 40

5.9 Cleaning flow rate monitor and check valve......................................................... 40

5.10 Cleaning ................................................................................................................ 41

6. Spare parts, Accessories and Retrofit kits ................................. 42

6.1 DEPOLOX® 5 E flow cell (module type D01) – non-pressurized version

W3T350215........................................................................................................... 42

6.2 DEPOLOX® 5 E flow cell (module type D01) – pressurized version W3T350216 .. 45

6.3 Cell body, DEPOLOX® 5 E flow cell........................................................................ 48

6.4 DFMe electronics module..................................................................................... 50

6.5 3-electrode measuring cell ................................................................................... 51

6.6 CAN bus extension cable for connection to DFMe electronics module................ 51

6.7 Sensors.................................................................................................................. 52

6.8 Accessories............................................................................................................ 54

6.9 Retrofit kits/extensions......................................................................................... 54

7. EC Declaration of Conformity and Certificate............................ 55

DEPOLOX® 5 E flow cell 1. Introduction

1. Introduction

1.1 Target groups

This instruction manual provides the informa-

tion for installation, operating and mainte-

nance personnel. It is required for operation

and maintenance of the DEPOLOX® 5 E flow

cell (module type D01).

All persons working with the DEPOLOX® 5 E

flow cell must have read and understood the

instruction manual, in particular, the safety

instructions it contains.

1.1.1 Documentation Structure

This instruction manual is intended for opera-

tors of the DEPOLOX® 5 E flow cell. It contains

important information for safe, trouble-free,

and efficient operation of the DEPOLOX® 5 E

flow cell. Observing these instructions will

help prevent risks, reduce repair costs and

downtimes, and increases the reliability and

service life of the DEPOLOX® 5 E flow cell

Chapters Installation, Commissioning, and

Maintenance are intended only for trained

and authorized service personnel. These chap-

ters contain important information on the

assembly, configuration, commissioning and

start-up, maintenance and repair that should

only be performed by this target group.

1.2 Conventions

This instruction manual contains a number of

notes with different priorities that are labeled

with pictograms.

DANGER

Immediate danger to life and limb! If the

situation is not corrected, death or serious

injury will result.

WARNING

Danger to life and limb! If the situation is not

corrected, death or serious injury can result.

ATTENTION

If this note is not observed, moderate or

minor injury or damage to equipment can

result.

WARNING

Electrocution hazard.

ATTENTION

Environmental hazard!

Do not throw away or burn the batteries!

Batteries must be disposed of at a collection

point.

NOTICE

These notes indicate a material risk or pro-

vide useful information to make working

with the DEPOLOX® 5 E

flow cell

easier.

2. Safety DEPOLOX® 5 E flow cell

2. Safety

2.1 Intended use

The DEPOLOX® 5 E flow cell (module type

D01) in combination with the installed sensors

and the 700 P electronics module (module

type E01) or 700 M electronics module

(module type E01) is intended only for measu-

rement and control in the treatment of drin-

king water, process water, industrial water,

wastewater, and swimming and bathing pool

water.

The operational safety of DEPOLOX® 5 E flow

cell is guaranteed only if it is used in accor-

dance with its intended application. It may

only be used for the purpose defined in the

order and under the installation, operating

and ambient conditions specified in this inst-

ruction manual.

All inspection and maintenance work must be

carried out in accordance at the specified

intervals.

Compliance with the intended use also inclu-

des reading this instruction manual and obser-

ving all the instructions it contains.

The operator bears full and sole responsibility

if this unit is put to any use which does not

comply strictly and exclusively with this inten-

ded use.

2.2 General safety instructions

The manufacturer places great value upon

safety when working with the unit. This was

already taken into account in the design of the

system, by the integration of safety features.

Safety regulations

The safety instructions in this documentation

must be observed. Additional industry-wide or

in-house safety regulations also continue to

apply.

Safety warnings on the unit

All safety instructions attached to the unit

itself must be observed. These instructions

must always be clearly legible and complete.

State-of-the-art technology

The unit has been constructed in accordance

with state-of-the-art technology and the

accepted safety regulations. However, if the

unit is used by persons who have not been

adequately instructed, risks to life and limb of

such persons or third parties and damage to

the unit itself or to other property cannot be

ruled out. Work not described in this instruc-

tion manual must be performed only by aut-

horized personnel.

Personnel

The operator of the overall system must

ensure that only authorized and qualified spe-

cialized personnel are permitted to work with

and on the unit within their defined scope of

authority. "Authorized, specialized personnel"

refers to trained technicians employed by the

operator, the manufacturer, or, if applicable,

the service partner. Only qualified electricians

must perform work on electrical components.

Spare parts / components

Trouble-free operation of the unit is only gua-

ranteed if original spare parts and compo-

nents are used in precisely the combination

described in this instruction manual. Failure to

observe this instruction may incur the risk of

malfunction or damage to the unit.

Extensions and conversions

Never attempt to perform any modifications,

extensions or conver-sions on the unit that

could have an adverse affect on safety with-

out the written approval of the manufacturer.

Electrical power

Only qualified electricians or trained person-

nel supervised by a qualified electrician are

permitted to perform any work on electrical

components and must do so in accordance

with valid electro-technical regulations.

During normal operation, the controller must

remain closed. Connect power cables in accor-

dance with the wiring diagram.

DANGER

Risk of injury or death!

The DEPOLOX® 5E flow cell must not be

used with flammable liquids.

DANGER

Risk of injury or death!

External voltages can be connected even

with the operating voltage switched off.

DEPOLOX® 5 E flow cell 2. Safety

IT security

The manufacturer offers IT security mecha-

nisms for its products to support secure sys-

tem operation. We recommend checking on a

regular basis to see what information is availa-

ble regarding IT security developments for

your products. Information on this can be

found on the Internet.

For the safe operation of an installation, it is

furthermore necessary to integrate the auto-

mation components into a holistic IT security

concept which comprises the entire system

and is in accordance with latest state of the art

technology. In the process, implemented pro-

ducts deriving from other manufacturers

should be taken into account.

Disposal

Ensure safe and environment-friendly disposal

of agents and replaced parts. Dispose of the

electronics waste in accordance with valid

local and national regulations.

2.3 Specific operating phases

• Never employ any working methods

which could affect safety!

• Never operated with flammable liquids.

• The flow cell may only be operated with

the housing closed!

• Inspect the flow cell at least once daily for

externally visible damage and faults!

Inform the responsible person/authority

immediately of any detected changes

(including any changes in the operating

performance)!

• Have malfunctions remedied immedia-

tely!

• During installation and maintenance

work, secure the flow cell against being

switched back on!

• If stipulated, disconnect all parts from the

power supply before performing any

inspection, maintenance or repair work.

Then first test the disconnected compo-

nents to ensure they do not carry any vol-

tage.

• Never use corrosive cleaning agents (e.g.

spirit, scouring agents)!

2.4 Warranty conditions

The following must be observed for compli-

ance with warranty conditions. If any of the

conditions are not met, the warranty is void.

• Installation and commissioning by the

manufacturer or trained and authorized

specialist personnel, e.g. from contracted

companies.

• Intended use

• Observation of the operational parame-

ters and settings.

• The unit may only be operated by trained

personnel.

• An operating log book must be kept (only

in the public sector).

• Only approved calibration chemicals may

be used.

• The unit must not be exposed to frost.

• The prescribed maintenance work must

be carried out.

• Use of original spare parts.

2.5 Exclusion of liability

We are not liable for any damages incurred

during installation or use of these hardware

and software components. This applies speci-

fically to trouble-free interaction with the

software and hardware components you

choose.

We accept no liability for any loss sustained by

the buyer (in particular, lost profits, lost infor-

mation and service interruptions) arising

through the use of the flow cell nor for other

damage. You are solely responsible for the ins-

tallation!

The content of the instruction manual has

been checked to make sure that it matches

the hardware and software described. Never-

theless, deviations cannot be ruled out, and

we therefore assume no liability for full con-

formity. The details in this instruction manual

are checked regularly and any necessary cor-

rections included in subsequent issues.

3. Description DEPOLOX® 5 E flow cell

3. Description

The DEPOLOX® 5 E flow cell (module type D01)

is part of the Pool Management System DEPO-

LOX® 5 E 700 P and the measuring and control

unit DEPOLOX® 5 E 700 M.

The DEPOLOX® 5 E flow cell (module type D01)

is a special flow cell adapter for sample water.

In combination with the 700 P electronics

module (module type E01) or 700 M electro-

nics module (module type E01) and the integ-

rated sensors, the DEPOLOX® 5 E flow cell

measures and controls parameters free chlo-

rine, pH value, redox voltage and temperature.

To determine parameters total chlorine, com-

bined chlorine and conductivity, further sen-

sors can e installed.

DEPOLOX® 5 E flow cell is available in both a

non-pressurized and a pressurized version.

The two versions differ in the number of sen-

sors that can be installed and in the design of

the sample water outlet. The non-pressurized

version is characterized by a free sample water

outlet. With the pressurized version, the sam-

ple water is returned into the system’s circuit.

The for sensors required for the measurement

tasks (optional) and the LED glow stick are

inserted or screwed into the mounting hole in

the cell body cover.

The maintenance-free flow control valve is the

main hydraulic part of DEPOLOX® 5 E flow cell.

It has the task of keeping the sample water

flow constant, irrespective of fluctuations in

operating pressures.

The multi-sensor monitors the correct flow

and records the temperature of the sample

water. The metallic sensor housing guarantees

good sample water earthing. The continuous

hydromechanical cleaning of the electrode of

the three-electrode measuring cell effectively

prevents natural contamination of the elec-

trode surfaces and ensures long-term stable

chlorine measurement.

DFMe electronics module converts the analog

sensor signals for digital transmission to 700 P

electronics module or 700 M electronics

module. If a membrane sensor for total chlo-

rine TC3 CAN (optional) is used, this is connec-

ted directly to DFMe electronics module or

routed through the CAN connection on con-

ductivity module SiDiSens (optional) to DFMe

electronics module. The conductivity sensor

(optional) is connected to DFMe electronics

module through conductivity module SiDi-

Sens.

3.1 Versions

The DEPOLOX® 5 E flow cell (module type D01)

can be comined with 700 P electronics module

(module type E01) or 700 M electronics

module (module type E01). The following ver-

sions are available:

• Pool Management System DEPOLOX® 5 E

700 P

• Measuring and control unit DEPOLOX® 5 E

700 M

3.1.1 Pool Management System

DEPOLOX® 5 E 700 P

The DEPOLOX® 5 E flow cell (module type

D01) is factory-configured according to the

customer’s specific requirements with the 700

P electronics module (module type E01) accor-

ding to the variant code. The scope of delivery

differs in the versions of DEPOLOX® 5 E flow

cell, the sensors, electronics components and

accessories. The variant code consists of 12

digits and is printed on both the type plate and

packaging sticker.

Part no. DEPOLOX® 5 E flow cell

W3T350215 Non-pressurized version

W3T350216 Pressurized version

DEPOLOX® 5 E flow cell 3. Description

Example

CPMNL4RLBDEOO

Selection of sensor measuring module for

free chlorine

Sensor measuring module DEPOLOX® Pool E

Sensor measuring module DEPOLOX® 5 E

Selection of sensor measuring module for pH value

P Sensor measuring module pH value

O No sensor measuring module pH value

Selection of sensor measuring module for

ORP (Redox) voltage

Sensor measuring module ORP voltage

No sensor measuring module ORP voltage

Selection of sensor measuring module for

total chlorine

NSensor measuring module total

chlorine TC

ONo sensor measuring module total

chlorine

Selection of sensor measuring module for

conductivity

L Sensor measuring module conductivity

No sensor measuring module conductivity

Selection of analog output

4 4-way mA analog output

O No 4-way mA analog output

Selection of relay board

R Additional relay board 4-way

O No additional relay board 4-way

Selection of DEPOLOX® 5 E flow cell

L Flow cell non-pressurized version

F Flow cell pressurized version

Selection of LED lighting

B LED glow stick for flow cell

Selection of language for instruction manual

DE Instruction manual in German

EN Instruction manual in English

FR Instruction manual in French

D2 Instruction manual in German/English

not used

3. Description DEPOLOX® 5 E flow cell

3.1.2 Measuring and control unit

DEPOLOX® 5 E 700 M

The measuring and control unit DEPOLOX® 5 E

700 M is available in various versions. They

mainly differ in the versions of the DEPOLOX®

5 E flow cell (module type D01) (non-pressuri-

zed or pressurized) as well as the sensors. The

measuring and control unit DEPOLOX® 5 E 700

M consists of the following:

• 700 M electronics module (module type

E01)

• DEPOLOX® 5 E flow cell (module type

D01) with 3-electrode measuring cell for

free chlorine (chlorine dioxide or ozone)

• Non-pressurized version or

pressurized version

•LED glow stick

• 4-way mA output card

• Eight relay outputs

Optional:

• pH reference electrode

• Redox reference electrode

• Membrane sensor for total chlorine TC3

CAN

• Conductivity sensor

DEPOLOX® 5 E 700 M - Non-pressurized version

Part no.

electrode measuring cell for free chlorine

(chlorine dioxide or ozone)

pH reference electrode

Redox reference electrode

Membrane sensor for

total chlorine TC3 CAN

Conductivity sensor

W3T371112 X

W3T371113 X X

W3T371114 X X X

W3T371115 X X X X

W3T371116 X X X X X

DEPOLOX® 5 E 700 M - Pressurized version

Part no.

electrode measuring cell for free chlorine

(chlorine dioxide or ozone)

pH reference electrode

Redox reference electrode

Membrane sensor for

total chlorine TC3 CAN

Conductivity sensor

W3T370967 X

W3T370968 X X

W3T370969 X X X

W3T370970 X X X X

NOTICE

The pressurized version can be retrofitted

with the total chlorine membrane sensor TC3

CAN. Please note that the standard cell body

cover must be replaced by an optional cell

body cover, part no. W3T417351.

DEPOLOX® 5 E flow cell 3. Description

3.2 Configuration options

Designation

DEPOLOX® 5 E flow cell

non-pressurized

version pressurized version

pressurized

version with cell

body cover

W3T417351

(optional)

A 3-electrode measuring cell (free chlorine)

B Membrane sensor for total chlorine TC3 CAN

C Conductivity sensor

D Redox combined measuring and reference electrode

ELED glow stick

F pH combined measuring and reference electrode

3-electrode measuring cell

(free chlorine) XXX

Membrane sensor for total

chlorine TC3 CAN X-X

pH combined measuring and

reference electrode XXX

Redox combined measuring

and reference electrode XXX

Conductivity sensor X X X

Sample water temperature

(multi-sensor) XXX

Flow rate monitor (multi-sensor)

XXX

Sample water earthing

(multi-sensor) XXX

Sample water fine filter

(fine filter). Only when using

membrane sensors

(X) - (X)

LED glow stick X X X

Shut-off ball valve at sample

water inlet XXX

Shut-off ball valve at sample

water outlet -XX

DEF

FED

DEF

3. Description DEPOLOX® 5 E flow cell

3.3 Spare Parts/extensions

3.4 Optional accessories

Please find order numbers in chapter 6.

• Strainer (chapter 4.8)

• Booster pump (chapter 4.8)

• Pressure reducing valve (chapter 4.8)

• PVC- or PE hose and hose connectors

(chapter 4.8)

• CAN bus extension cable (chapter 4.4)

3.5 Design and functions

3.5.1 Overall design

Abb. 1 DEPOLOX® 5 E flow cell, non-pressurized

A Cover for holding the sensors and LED

glow stick (cell body cover)

B Plastic housing with removable housing

cover

C Cell body

D DFMe electronics module

E Calibration holding clip

F 3-electrode measuring cell with electrolyte

tank

G Cap of the 3-electrode measuring cell

H Sample water outlet, in pressurized versi-

on also with ball valve

I Sample taking unit (drain)

J Sample water inlet

K Shut-off ball valve

L Filter unit

M Check valve housing

N Flow control valve

OMulti-sensor

P Module SiDiSens conductivity (optional)

Part No. Designation

W3T320090* Sensor measuring module

DFMe Total chlorine TC3 CAN

W3T417351* Cell body cover, fully pressu-

rized version

W3T320088 Sensor measuring module

DFMe pH

W3T320089 Sensor measuring module

DFMe ORP (Redox)

W3T320091

Sensor measuring module

DFMe Conductivity LF325 -

60 mS/cm

W3T320092

Sensor measuring module

DFMe Conductivity LF325

600 µS/cm

NOTICE

*The pressurized version can be retrofitted

with the total chlorine membrane sensor TC3

CAN. Please note that the standard cell body

cover must be replaced by an optional cell

body cover (part no. W3T417351), see chap-

ter 4.21.2).

HIJ

DEPOLOX® 5 E flow cell 3. Description

3.5.2 Function

The sample water is connected on the input

side to the shut-off ball valve via the G1/2”

connection. The input pressure must be

around 0.25 to 3.0 bar. To guarantee a cons-

tant flow, the minimum input pressure must

not be less than 0.25 bar. Otherwise, an opti-

onal booster pump must be used. If the admis-

sion pressure exceeds 3.0 bar, an optional

pressure reducing valve must be used.

The sample water flows over the optional

strainer, which prevents dirt particles pene-

trating into the flow cell.

The sample water flows in the flow direction

to the check valve housing through the filter

unit or through the built-in fine filter (memb-

rane sensors only). In the filter unit a stainless

steel fine filter (sample water fine filter) with a

mesh size w=500 µm can be installed. The fine

filter is only used in conjunction with the

membrane sensors.

The check valve housing provides a kick-back

function and guides the ball for monitoring

the flow rate.

The multi-sensor monitors the correct flow by

the float principle with reed switch and mea-

sures the temperature with the Pt1000. The

large-surface transducer grounding is through

the stainless steel sensor housing.

The flow control valve ensures a flow of the

sample water that is not dependent on the

operating pressure. The correct sample water

flow of 33 l/h is factory-preset, checked and

logged. If the admission pressure rises, the

valve ball moves towards the closing direc-

tion; if the admission pressure drops, the ball

moves towards the opening direction.

In the cell body the 3-electrode measuring cell

(H) with external potentiostatic control circuit

and refillable electrolyte tank is fitted. Wor-

king and counter electrodes are designed as

half-ring electrodes and consist of a special

platinum alloy. The reference electrode is a sil-

ver–silver chloride electrode, which is connec-

ted to the sample water via two membranes.

The reference electrode immerses in an elec-

trolyte solution and can also be refilled during

operation.

The sample water that flows tangentially into

the 3-electrode measuring cell ensures conti-

nuous hydromechanical cleaning of the sensor

electrodes with special cleaning sand, thereby

preventing natural soiling of the electrode sur-

faces. Clean electrode surfaces and a constant

flow of sample water are decisive criteria for a

qualitative good oxidizing agent measure-

ment and quick response.

The 3-electrode measuring cell is connected

to 700 P electronics module or 700 M electro-

nics module through DFMe electronics

module (DES sensor module for 3-electrode

measuring cell). The adjustable cell voltage

Upot is output through the potentiostatic con-

trol circuit. A measuring cell current (µA sig-

nal) that is proportional to the disinfectant

concentration in the sample water is evalua-

ted with the 700 P electronics module or

700 M electronics module.

The cell body, which can be lit, holds the sen-

sors and is designed to allow convenient clea-

ning and servicing. These additional sensors

are installed in the mounting hole of the cell

body cover with standard thread connections

or in special sensor mounts.

The LED glow stick is fitted in the cell body

cover for visual inspection of the sensors, sand

cleaning and for color indication of messages

or faults.

The sample water runs off directly through the

top cell body outlet through an outlet nozzle

for hoses with inner diameter 6 mm. In the

case of the pressurized version, the sample

water runs off through a shut-off ball valve

with G 1/2” A-connection. With the pressuri-

zed version, a maximum back pressure of 1.5

bar is permitted here.

For calibration, a sample taking unit is fitted. It

is used to draw sample from the cell body

through the low-pressure side of the flow con-

trol valve and to drain the cell body for servi-

cing.

Two calibration holding clips are attached in

the cover of the DEPOLOX® 5 E flow cell. For

hands-free calibration of the sensors with buf-

fer solution and calibration solution (bag or

cup) the two calibration mounting brackets

are inserted on the side at the back of the

main housing.

3. Description DEPOLOX® 5 E flow cell

3.5.3 DFMe electronics module

DFMe electronics module consists of a spray-

water tight housing with built-in sensor elec-

tronics and is integrated in the main housing

of the flow cell. The sensor cables are prefabri-

cated and are splash-proof to IP66. The

motherboard holds the sensor input for the 3-

electrode measuring cell, the LED glow stick

and the evaluation electronics for the multi-

sensor. Optionally, the motherboard contains

two additional slots for the pH and redox com-

bined measuring and reference electrode. To

the integrated CAN socket the CAN connection

cable to 700 P electronics module or 700 M

electronics module is connected. Further opti-

onal sensors, such as for total chlorine and/or

conductivity module SiDiSens can be connec-

ted through a second CAN connection socket

(optional). See design chapter 4.15 - Fig. 13.

3.5.4 Module SiDiSens LF (optional)

To measure the conductivity, conductivity

module SiDiSens LF (optional) is installed in

DEPOLOX® 5 E flow cell. The SiDiSens LF

module contains the sensor electronics for

conductivity sensor LF325 (4-conductor mea-

surement). Through the CAN interface the

SiDiSens LF module is connected with 700 P

electronics module or 700 M electronics

module. In addition, the optional membrane

sensor for total chlorine TC3 CAN can be con-

nected via the CAN socket. See design chapter

4.21.1 - Fig. 19.

3.6 Sensors

The DEPOLOX® 5 E flow cell (module type D01)

can optionally be equipped with the following

sensors.

• pH combined measuring and reference

electrode

• Redox combined measuring and reference

electrode

• Conductivity sensor with conductivity

module SiDiSens

• Membrane sensor for total chlorine TC3

CAN

Please find order numbers in chapter 6.7.

Please follow the relevant instruction for the

sensors.

DEPOLOX® 5 E flow cell 3. Description

3.7 Technical Data

3.7.1 DEPOLOX® 5 E flow cell (module type D01)

3.7.2 3-electrode measuring cell

Housing Dimensions (WxHxD) 253 x 375 x 163 mm

Weight approx. 2.5 kg

Connections

Non-pressurized version

Inlet: G 1/2” A thread connection

Outlet: Connecting nipple for hoses

ID 6 mm

Pressurized version Inlet and outlet:

G 1/2” A thread connection

Flow control valve

Sample water flow 33 l/h, controlled, preset at the factory

Flow control range 0.25 to 3.0 bar admission pressure

Back pressure Non-pressurized version: free drain

Pressurized version max. 1.5 bar

Multi-Sensor

Switching point 21 l/h ±3 l/h

Switching hysteresis 2 l/h

Temperature sensor Pt1000

Sensors Measured variables Free chlorine, chlorine dioxide, ozone

Design Potentiostatic 3-electrode measuring cell with platinum electrodes,

tank with reference electrolytes, two diaphragms, Ag/AgCl drain system

Measurement range 0 to 50 mg/l (chlorine reference value)

Working temperature

range 0 to 50°C (32 to 122°F)

Area of application,

pH value constant, within range pH 4 to pH 9

Influence of the pH

value HOCl characteristic (for chlorine)

Measurable parame-

ters Free Cl

, ClO

, O

, KMnO

Conductivity >= 100 µS/cm

Response time t

= < 20 s

Typical output signal 20 µA/mg/l (for chlorine)

Storage temperature -10 to +50°C (14 to 122°F)

3. Description DEPOLOX® 5 E flow cell

3.7.3 Sensors (optional)

pH combined measuring and reference electrode (W3T169297)

Design

Combined measuring and reference electrode with universal memb-

rane glass, salt reserve, zirconium dioxide diaphragm, polymerized solid

electrolyte, Ag/AgCl drain system

Measurement range pH 0 to 12 (temporarily to pH 14)

Working temperature

range -5 to +80°C (23 to 176°F)

Operating pressure 0 to 6 bar (6 × 10

Pa)

Minimum conducti-

vity of the sample

water

50 µS/cm

Installation length 120 mm

Screw-in thread PG 13.5

Storage temperature -5 to +30°C (23 to 86°F)

Redox combined measuring and reference electrode – platinum version (W3T169298)

Design

Combined measuring and reference electrode with platinum electrode,

salt reserve, zirconium dioxide diaphragm, polymerized solid

electrolyte, Ag/AgCl drain system

Measurement range ±2000 mV

Working temperature

range -5 to +80°C (23 to 176°F)

Operating pressure 0 to 6 bar (6 × 10

Pa)

Minimum conducti-

vity of the sample

water

50 µS/cm

Installation length 120 mm

Screw-in thread PG 13.5

Storage temperature -5 to +30°C (23 to 86°F)

Conductivity sensor (W3T172052)

Design 4-electrode measurement, integrated temperature sensor, graphite

electrodes, epoxy shaft

Measurement range 1 µS/cm to 2 S/cm

Cell constant 0.475 cm

-1

±1.5%

Working temperature

range -5 to +100°C (23 to 212°F)

Operating pressure

(electrode shaft) 0 to 10 bar (1 × 10

Pa)

Installation length 120 mm

Installation Loose

Protection rating IP 67 (in plugged in state)

Storage temperature 0 to +50°C (32 to 122°F), store in the fresh air

DEPOLOX® 5 E flow cell 3. Description

3.7.4 DFMe electronics module

3.7.5 Module SiDiSens LF (optional)

Design Sensor electronics integrated in the flow cell for connection

of:

• 3-electrode measuring cell

•Multi-sensor

•LED glow stick

• pH electrode

• Redox electrode

Power supply 24 V DC

Connection 5-pole M12 socket for CAN interface and 24 V DC supply

Extension option for second 5-pole M12 socket

Storage temperature -20 to +70 °C

Ambient temperature 0 to 50 °C

Environment No direct sunlight

Atmospheric pressure 75 to 106 kPa

Max. working height 2,000 m

Relative humidity < 80 %, non-condensing

Noise emission < 45 dB

Design Sensor electronics integrated in the flow cell for connection of

the conductivity sensor:

Connection 5-pole M12 socket for CAN interface extension;

CAN connection cable with 5-pole M12 plug for connection to

the DFMe;

Sensor cable for connection of the conductivity sensor LF325

(4-electrode system)

Power supply 24V DC via CAN connection cable

Storage temperature -20 to +70 °C

Ambient temperature 0 to 50 °C

Environment No direct sunlight

Atmospheric pressure 75 to 106 kPa

Max. working height 2,000 m

Relative humidity < 80 %, non-condensing

Noise emission < 45 dB

4. Installation DEPOLOX® 5 E flow cell

4. Installation

4.1 Scope of supply

The DEPOLOX® 5 E flow cell (module type D01)

can be comined with 700 P electronics module

(module type E01) or 700 M electronics

module (module type E01). Depending on the

individual order, the scope of supply includes

the following:

• Pool Management System DEPOLOX® 5 E

700 P

• Measuring and control unit DEPOLOX® 5 E

700 M

4.1.1 Pool Management System

DEPOLOX® 5 E 700 P

The scope of delivery of the DEPOLOX® 5E

flow cell inclu®es the following:

•DEPOLOX®

5 E flow cell (module type D01)

with 3-electrode measuring cell for free

chlorine (chlorine dioxide or ozone)

• Non-pressurized or pressurized ver-

sion

•LED glow stick

•Top-hat rail

• Assembly accessories

• Instruction manual

4.1.2 Measuring and control unit

DEPOLOX® 5 E 700 M

The scope of supply of the measuring and con-

trol unit DEPOLOX® 5 E 700 M includes the fol-

lowing, depending on the order:

•DEPOLOX®

5 E flow cell (module type D01)

with 3-electrode measuring cell for free

chlorine (chlorine dioxide or ozone)

• Non-pressurized version or

pressurized version

• 700 M electronics module (module type

E01)

• With 4-way mA output card

•8x relay outputs

•LED glow stick

•Top-hat rail

•Assembly accessories

• Instruction manual DEPOLOX® 5 E flow

cell, German/Englisch

• Instruction manual 700 M electronics

module, German/Englisch

4.2 Transport and storage

Transport

The flow cell is supplied in standard packaging.

During transport, the packaged system must

be handled carefully and should not be expo-

sed to wet weather or moisture.

Check that the transport packaging is unda-

maged. In the event of damage, please inform

the transport company immediately, as your

rights to compensation will otherwise be lost.

If a component is damaged, please contact

your affiliate immediately.

Keep the packaging until the flow cell has been

correctly installed and taken into operation.

Storage

Store the electronics module, the flow cell and

the sensors in a dry condition without any resi-

dual water in a dry place that is not exposed to

the weather. .

Shut-down

The flow cell may only be taken out of opera-

tion by trained and authorized personnel.

NOTICE

The DEPOLOX® 5 E flow cell is factory-confi-

gured according to the customer’s specific

requirements with the 700 P electronics

module according to the variant code (chap-

ter 3.1.1).

NOTICE

The scope of supply mainly differs in the ver-

sions of the DEPOLOX® 5 E flow cell (non-

pressurized or pressurized) as well as the

sensors.

ATTENTION

Damage to device and sensor!

Observe different storage temperatures

(chapter 3.7) and manufacturer specifica-

tions of the buffer solution and calibration

solution.

DEPOLOX® 5 E flow cell 4. Installation

4.3 Ambient conditions

4.3.1 Installation site

The following points must be taken into

account when installing flow cell:

• The flow cell must be protected from

moisture, rain, frost, heat and direct sun-

light and must not be installed outdoors.

• Do not use the flow cell in environments

where there are flammable gases, fumes

or dust or conductive dust.

• Do not subject the flow cell to strong

shocks or vibrations.

• The air in the room should be non-con-

densing.

4.3.2 Installation location for drinking

water, industrial water and waste

water

For problem-free mixing of the chlorine solu-

tion, the distance between chlorine addition

and sample water take-off must be at least ten

times the pipe diameter:

Example:

Pipe DN300

=> 300 mm × 10 = 3000 mm

=> minimum distance = 3 m

The time between chlorine addition and

excess chlorine measurement is the soak time.

It consists of the travel time between chlorine

addition point and sample water take-off and

the travel time between sample water take-off

and measurement (sample water line to flow

cell). Keep the sample water line to the flow

cell as short as possible.

For longer required soak times, for example 5

to 15 minutes, a delay tank can be installed

into the sample water line immediately before

the flow cell. Note that the longer soak time

prevents chlorine addition control based

purely on excess chlorine. Instead, combined

flow and excess chlorine dependent control

must be used. This also applies to the use of

chlorine, chlorine dioxide and ozone as disin-

fectant.

4.3.3 Installation site for pool water

The sample water take-off point must be

installed in the pool return line according to

standards (see DIN 19643, DIN = German

Industrial Norm). Make sure that the sample

water take-off point is upstream of the floccu-

lant station.

4.4 Mechanical installation

NOTICE

Correct and safe operation can only be gua-

ranteed if the requirements for the ambient

conditions are met. All applicable national

and local regulations must be observed!

WARNING

Risk of injury or damage to the installation!

• Only authorized and qualified electrici-

ans are permitted to install the flow cell.

• All electrical work on the equipment

must be performed only by authorized

and qualified electricians.

• Modifications to the device other than

those described in this instruction

manual are not permitted.

NOTICE

• Install the flow cell to the left of the

electronics module.

• Leave a clearance of at least 250 mm

above the flow cell for working with the

sensors.

• Screws and dowels for fixing to a solid

wall are included in the scope of delivery.

• Tallow-drop screws and dowels for fixing

to a solid wall are included in the scope

of delivery.

• If the device is to be installed on a suita-

ble lightweight wall, use the appropriate

mounting fixtures. Not included in the

scope of delivery!

• The electronics module is not suitable

for electrical connection with perman-

ently installed cable conduits. If the

cable glands do not meet local installa-

tion rules and regulations, these glands

must be replaced with suitable ones.

• If electronics module and flow cell are

installed in different locations, you must

use CAN bus extension cable (optional).

This must not be longer than 1000 m.

• Measurement are shown in millimeters.

To convert to inch measurement, divide

by 25.4 (1 inch = 25.4 mm).

4. Installation DEPOLOX® 5 E flow cell

1 Installation of the module (chapter 4.5).

2 Remove the housing cover of the flow cell

(chapter 4.6).

3 Install the optional strainer (chapter 4.7).

4 Connect the sample water inlet (chapter 4.8)

• with tubing connection

• with rigid pipework

5 Connect the sample water outlet (chapter

4.9).

6 Installing the fine filter (chapter 4.11).

Only when using the membrane sensor.

7 Removing the felt ring (chapter 4.12).

8 Removing and replacing transport caps

(chapter 4.13).

9 Insert electrode cleaning sand (chapter

4.14).

Connecting the three-electrode measuring

cell and connecting sensors with DFMe

electronics module

(chapter

4.15

11 Fitting the sensors (chapter 4.16).

12 Fit calibration aids (chapter 4.17).

13 Refit the housing cover (chapter 4.6).

4.5 Installation of the module

Install the electronics module and flow cell

with or without DIN rail. Dimension drawing

chapter 4.5.3.

4.5.1 With DIN rail

1 Secure the DIN rail to a solid wall using

the dowels and screws supplied.

2 Hook the electronics module onto the DIN

rail so that it is flush at the right.

3 Fasten the electronics module to the solid

wall at the bottom by the holders using

dowels and screws.

4 Hook the flow cell on the DIN rail to the

left of the electronics module.

5 Fasten the flow cell to the solid wall at the

bottom by the holders using dowels and

screws.

4.5.2 Without DIN rail

The dimensions for the drilling pattern can be

found on the back of the plastic housing.

1 Attach the tallow-drop screws and dowels

provided to the solid wall (included in the

scope of delivery).

2 Hook the electronics module onto the

screws.

3 Fasten the electronics module to the solid

wall at the bottom by the holders using

dowels and screws.

4 Hook the flow cell onto the screws.

5 Fasten the flow cell to the solid wall at the

bottom by the holders using dowels and

screws.

Page is loading ...

Evoqua W3T350215 User manual

Brand: Evoqua

Model: W3T350215

Type: User manual

This manual is also suitable for

WALLACE & TIERNAN DEPOLOX 5 Series

Download PDF

report

Evoqua W3T350215 User manual

This manual is also suitable for

Evoqua W3T350215 User manual

Related papers

Other documents