DanVex DEH-600wp User manual

Brand: DanVex

Model: DEH-600wp

Category: Dehumidifiers

Type: User manual

This manual is also suitable for

DEH-1000wp

DEH-600wp

DEH-1000wp

Instruction manual

Dehumidifiers for swimming pools

www.danvex.fi

Please read this instruction manual carefully and save it before using the dehumidifier. If you

have any questions about using the dehumidifier, please contact Your dealer.

www.danvex.fi 2

INTRODUCTION .............................................................................................................................

PRECAUTIONARY MEASURES .....................................................................................................

DESCRIPTION OF THE DEHUMIDIFIER .......................................................................................

WIRING DIAGRAMS .......................................................................................................................

INSTALLATION NOTE ....................................................................................................................

START-UP AND OPERATION (DESCRIPTION OF THE CONTROL PANEL) ................................

REMOTE CONTROL AND ERROR CODES ...................................................................................

DEHUMIDIFIER MAINTENANCE ....................................................................................................

TECHNICAL SPECIFICATIONS ......................................................................................................

WARRANTY TERMS AND WARRANTY CARD ..............................................................................

CONTENTS

www.danvex.fi

INTRODUCTION

MODELS:

DEH-600wp

DEH-1000wp

All the dehumidifiers described in this manual are designed to maintain the relative

humidity of indoor air in the range from 40% to 99%, at air temperature from +10°C to

+32°C.

www.danvex.fi 4

 Read this manual carefully for safety before

you start operating the dehumidifier. Below are

the symbols used in this manual.

If dirt sticks to the plug of the power cord

or plug and socket connection is loose, it

may cause fire or electric shock.

PRECAUTIONARY MEASURES

CAUTION

Remove any dirt from the plug

of the power cord.

There should be no breaks in the cord

or its artificial extensions.

Do not scratch or bend the power cord.

Do not place heavy objects on the power

cord, heat it, or expose to other factors. The

cable may be damaged, which can lead to fire

or electric shock.

Consult Your dealer on installation

of the device.

Do not insert fingers or any objects

into the air intake/ outlet.

Do not attempt self-repair or re-installation

of the device.

If this is done incorrectly, it may cause fire,

electric shock, water leakage, etc.

Contact Your dealer.

Strictly forbidden

Be sure to follow the

instructions

Provide grounding

Unplug the power cord from

network

Never store anything on the

device

Electric shock hazard

Never insert fingers

or any items

Do not disconnect / do not connect

power supply during operation

If during operation there is something

unusual (burning smell, etc.), turn

off the device and disconnect it from

the network

Use grounding.

In case of incorrect operation of the device,

contact Your dealer.

Avoid contact of the grounding

wire with gas and water pipes,

lightning rod or telephone cable. If

the grounding is made incorrectly,

it can lead to defeat electric shock

hazard.

www.danvex.fi

This may cause fire or deformation.

PRECAUTIONARY MEASURES

CAUTION

Do not use insect repellent or solvents.

Before cleaning the device switch it off

and disconnect the power cable from

the mains.

It can cause a short circuit that may result

in electric shock or fire.

Do not clean the device with water.

● This can lead to electric shock.

As the fan rotates at high speed, cleaning of

operating device can cause injury.

If the device is installed in a damp

location, ensure its isolation from

moisture.

If you do not provide isolation

of the device from moisture, it may

cause electric shock.

If You do not, the device may accumulate dirt

and cause a fire.

If You are not going to use the device

during a long period, unplug it from

the mains.

Do not install the device in a place where

there is flammable gas.

Do not install the device where in unsafe

operation conditions.

Do not press the switches with wet hands.

This may cause electric shock.

Unassisted installation of the device is

forbidden.

If this is performed incorrectly, it may cause

fire, electric shock, water leakage, etc.

Please contact Your dealer or technician.

Do not pull on the power cord.

www.danvex.fi 6

AIR DEHUMIDIFIERS: DEH-600wp and DEH-1000wp

DEHUMIDIFIER DESCRIPTION

Power cordPower cord

Drain hose

Moist air input

Mounting bracket Dry air output Control panel

www.danvex.fi 7

DEH-600wp, DEH-1000wp

SINGLEPHASE (1PH/50 Hz)

WIRING DIAGRAM

Датчик

влажности Датчик температуры

воздуха

Датчик системы

разморозки

Вывод на дисплей PCB

Трансформатор

Главный контроллер PCB

Мотор

вентилятора

Компрессор

Источник питания

Main controller PCB

Humidity detector

Air temperature sensor

System defrost sensor

PCB display representation

Compressor

Fan motor

Power source

Transformer

Protection from low pressure

Protection from high pressure

www.danvex.fi 8

INSTALLATION NOTE

Mounting of the dehumidifier on the wall:9

Step 1: Select the correct position for mounting on the wall, depending on the size of the

holes set and the holes positions of the wall mount bracket. The place of installation should

guarantee the vertical position of the dehumidifier. Mark places for drilling.

Step 2: Use hammer drills to drill holes with depth of 8 ± 0.5 cm Then use the anchor bolts

and install them into the holes with a hammer.

Step 3: Install the wall bracket with anchor bolts in the correct position. Please, provide

secure fixing of the bracket using nuts and washers. Don't forget to hold the bracket in the

correct position during installation.

Step 4: Install the dryer on the wall bracket.

Step 5: Connect the drain hose to the dehumidifier. Turn on the dehumidifier for trial use.

Check the device for presence of abnormal vibration and noise.

Step 6: Installation is finished and the dehumidifier is ready for use.

Installation diagram.

In case of indoor installation of the device, provide availability of free space for its

maintenance. The premises, where the device is installed, must be ventilated.

Before installation of the dehumidifier:

Before shipment from the factory all the dehumidifiers are subject to tests. Unpack the box

and check for damage on the surface of the device, as well as for completeness of

components in accordance with the list specified in the instructions. If You find any damage,

do not attempt to install the humidifier and immediately contact the supplier.

IF DURING TRANSPORT THE DRYER WAS LYING ON THE SIDE, IT NEEDS

TO BE LEFT UPRIGHT FOR AT LEAST 24 HOURS BEFORE THE START OF

ITS OPERATION!!!

(failure to perform this may cause damage to the dryer and void your warranty)

CAUTION!!!

www.danvex.fi

START-UP AND OPERATION

Description

The control panel is designed to exercise the control functions over the dehumidifier

operation, change of parameters of operation and maintenance of the specified values

for these parameters. The panel consists of control buttons and LCD screen.

Buttons are used for switching on/off and changing of parameters and modes of

operation of the dehumidifier. At the top of the panel screen the current time (if

configured), and operation mode on the basis of the built-in humidity sensor, constant

operation, ventilation mode, current values of humidity and temperature, set/preset

humidity value, the status of the timers and their settings are displayed.

Designation of control buttons:

(ON/OFF) - on / off of the dehumidifier,

(UP) - increase of the parameter (humidity, time),

(DOWN) - decrease of the parameter (humidity, time),

(MODE) - Change (selection) of the operation mode (built-in humidity

sensor / external humidity sensor / constant dehumidification / ventilation

mode),

(TIME) - setting the timers and time

(TIMERSET) - selection of timer operation mode (off /once /daily)!

Names an values of parameter:

INTERNAL - activated internal / built-in humidity sensor, EXTERNAL -

activated external humidity sensor (have to be connected, in the

absence of contact, error E7 is displayed),

CURRENT HUMIDITY - current/valid humidity,

CURRENT TEMPERATURE - current/actual air temperature,

TIMER ON – time of switching on the dryer when the timer is

operating;

TIMER OFF – time of switching off the dryer when the timer is

operating;

OFF - timers are disabled,

TIME - single cycle of the timer operation;

EVERY DAY - daily mode of the timer operation.

Control panel of the dehumidifier

www.danvex.fi 10

START-UP AND OPERATION

CAUTION!!!

Please carefully review the control functions and make all necessary

adjustments before using the dehumidifier.

Operation procedure and parameters setting.

For starting of dehumidifier you need to make some not difficult things:

1. By the means of one-time push of the ON/OFF button, the dehumidifier is switched on, the

panel issues a short beep and the screen lights are activated.

2. By the means of pressing UP and DOWN buttons set the required humidity value (displayed in

large digits) which is expected to be maintained in the premises (by default 60%).

3. The MODE button will enable the INTERNAL mode for operation on the built-in humidity

sensor or EXTERNAL mode for operation on the external humidity sensor (not supported).

4. If the current humidity is higher than the preset by at least 2-3%, the dehumidifier starts running

(the fan, then the compressor/compressors are enabled). The dehumidifier will be disabled at

excess of the fixed value by 2-3%.

The clock and timers setting.

To set the time, press the TIME button, at the top of the screen the two characters will flash,

responsible for the clock "- - " - - . Then, by the means of the UP and DOWN buttons set the

current time in hours. Then press the button TIME again, the characters responsible for the

minutes - - " - - " will flash, by the means of pressing UP and DOWN buttons set the current time in

minutes.

To configure the on / off timers, press the button TIME three times, the symbols of hours of the

timer will be flashing, by the means of pressing the UP and DOWN buttons, set the time in hours,

press the TIME button again, the symbols of the timer minutes will be flashing, by the means of

pressing the UP and DOWN buttons, set the time in minutes. Press the TIME button again, the

symbols of hours of the off-timer will be flashing, by the means of UP and DOWN buttons select

the off time in hours, press the TIME button again, the symbols of the minutes of the off-timer will

be flashing, by the means of the UP and DOWN buttons select the off time in minutes.

Now select the mode of operation of the timer by the TIMERSET button.

www.danvex.fi

REMOTE CONTROL AND ERROR CODES

REMOTE CONTROL

ERROR CODES

The dehumidifier is equipped with a self-diagnostic system. In case of

detection of problems, the error code will be represented at the LCD display.

E2 - heat exchanger temperature sensor error;

E3 - air temperature sensor error;

E7 - humidity sensor error .

The scope of supply includes the infrared

remote control. The remote buttons

duplicate some of the functions of the

control panel of the dehumidifier. To start

using the remote you need to insert the

battery R232 (supplied separately).

Button up

Button down

Оn/off button

www.danvex.fi 12

DEHUMIDIFIER MAINTENANCE

When You are not going to use the

dehumidifier for a long time.

When you are going to operate

the dehumidifier again.

Start the process of air drying for 3-

4 hours, setting the humidity levels

at the level of 80% to dry the

dehumidifier from inside.

Switch off the dehumidifier, then

remove plug from outlet.

Make sure the air intake and outlet are

not blocked.

Make sure the ground wire is connected

properly

CAUTION

Switch off the dehumidifier or remove the

plug from the socket if you are not going

to use it for a long time.

CAUTION

Use grounding.

Avoid contact of the grounding wire with

gas and water pipes, lightning rod or

telephone cable. If grounding was

performed incorrectly, this may result in

electric shock.

Remove the batteries from the remote control.

Model DEH‐600w DEH‐1000wp

Voltage

Productivity (l/day) at 30°С/80% 60 100

Power (W) 920 1260

Current strength (А) 04.мар 6

Air capacity (mЗ/hour) 450 500

Refrigerant volume, trademark (year, R407C) 500 550

Noise level (dB) 46 48

Net weight(kg) 50 55

Overall dimensions LxWxH (mm) 915X280X670 915X280X670

230V/1~/50Hz

www.danvex.fi

TECHNICAL SPECIFICATIONS

NOTE:

1. The nominal value of the noise level recorded in the laboratory.

2. In case of difference between the characteristics shown in the table above and

the characteristics specified directly on the manufacturer label, you need to rely

on the characteristics of the manufacturer's label.

3. Test data: air temperature 30°C, humidity 80%.

SPECIAL INSTRUCTIONS:

1. For expert installation and repair, contact the special Service department.

2 If a flexible cable is damaged, contact the special Service Department to replace it

with the original cable.

WARRANTY CARD AND WARRANTY OBLIGATIONS

ITEM TYPE, MODEL: ____________________________________________________

PURCHASE DATE:__________________

Warranty scope and equipment, to which warranty is applied:

The equipment covered by this warranty is listed below:

The supplier will provide a replacement part in case of its failure during normal use in non-

aggressive dust-free environment and regular maintenance during the warranty period

specified below, in accordance with the terms of this warranty.

The date of delivery of warranty replacement parts is 30 days.

The warranty for the replaced item will be given only for the remaining period of the

original warranty period.

Equipment subject to guarantees:

The warranty is applied to all equipment DanVex and its components.

Date of entry into force and guarantee terms:

Start date of warranty period is the date of sale. The warranty period for dehumidifiers

DanVex of the series "wp" is 24 months.

Exceptions -

THIS WARRANTY DOES NOT COVER:

1. Equipment, which was not installed in accordance with the manual.

2. Equipment, which is not operated in accordance with the manual, for example, in

aggressive environments (oils, salts, chlorine, etc. high temperature), multiple cover

damages.

3. Items returned not through the distributor of the Manufacturer.

4. Items returned later than 30 days after failure.

5. Items returned after the date of expiration of the warranty period, including the items,

gone out of operation during the warranty period, but returned after its expiration.

6. Damage, malfunction or failure that occurred during or as a result of transportation or

movement, improper operation, accidental accidents, fires, floods and other similar

situations.

7. Equipment in dirty state.

8. Damage, malfunction or failure occurring as a result of installation, operation or

maintenance of the unit, produced not in accordance with the Manufacturer's instructions

outlined in the installation manual, in violation of the accepted manufacturing practices and

any applicable local, state and national standards.

9. Damage, malfunction or failure occurring as a result of using additional equipment,

accessories, or parts that have not received approval and authorization of the Manufacturer.

www.danvex.fi 14

Compliance with the declared characteristics:

The manufacturer guarantees the compliance of the technical characteristics of the equipment

stated in the instruction manual, only subject to clean state of the equipment, and its operation

under normal conditions (humidity and temperature of the environment is not more/ less than

that specified in the operating instructions).

Transportation costs:

The manufacturer is not responsible for the costs of transportation of equipment and spare

parts.

Cost of works:

The manufacturer is not responsible for costs of dismantling and replacement of equipment.

Costs of examination:

If it is determined that the returned items are not defective and are operable within design

standards, the manufacturer reserves the right to receive payment for the examination in the

amount of 50 Euro in addition to the transportation costs.

THIS CONTRACT WARRANTY EXCLUDES ALL OTHER WARRANTIES OR

REPRESENTATIONS, EXPLICIT OR IMPLIED, IN/BY ANY DOCUMENTS, DATA, OR

PERSONS. THE MAXIMUM LIABILITY OF THE SUPPLIER UNDE THIS EXCLUSIVE LEGAL

REMEDY MAY NOT EXCEED THE COST OF PRODUCTION, AND THE SUPPLIER

RESERVES THE RIGHT, IN SOLE DISCRETION, TO REIMBURSE THE COST OF

PURCHASED EQUIPMENT INSTEAD OF ITS REPAIR OR REPLACEMENT. THE SUPPLIER

IS NOT LIABLE FOR ANY DIRECT, INDIRECT, ASSOCIATED WITH THE PARTICULAR

CIRCUMSTANCES OR INCIDENTAL DAMAGES CAUSED BY BREACH OF WARRANTY,

OR COMING FROM OTHER LEGAL BASIS, INCLUDING LOST PROFITS, LOSS OF

REPUTATION, TIME, INCONVENIENCE, FUEL AND LABOR COSTS, OR OTHER

INCIDENTAL OR CONSEQUENTIAL LOSS OR DAMAGE INCURRED BY PERSONS,

COMMERCIAL ORGANIZATIONS, OR THEIR PROPERTY, AS A RESULT OF BREACH OF

WARRANTY, NEGLIGENCE, AND OTHER CONDITIONS. THIS WARRANTY IS DEFINED

AND LIMITED BY THE FOREGOING SPECIFIC CONDITIONS AND IS THE ONLY LEGAL

REMEDY.

www.danvex.fi 15

Details of the seller:

Name of the organization:_________________________________________________

__________________________________________________________

Address:__________________________________________________________________

Telephone number:__________________________________________________________

Details of the buyer:

Full name (Organization): ____________________________________________________

__________________________________________________________________________

Address:__________________________________________________________________

Telephone number:__________________________________________________________

www.danvex.fi

Seal

(for the legal person)

THE MANUFACTURER DOES NOT GUARANTEE COMPATIBILITY OF THE PURCHASED

EQUIPMENT WITH THE EQUIPMENT OF THE BUYER. THE SELLER GUARANTEES

SERVICEABILITY OF EACH OF ACCESSORIES SEPARATELY, BUT IS NOT RESPONSIBLE

FOR THE QUALITY OF THEIR JOINT FUNCTIONING, EXCEPT WHEN PURCHASED IN THE

SET AND INSTALLED ACCORDING TO THE RECOMMENDATIONS OF THE DISTRIBUTOR.

IN ACCORDANCE WITH THE LAW OF THE RF “ON PROTECTION OF CONSUMER RIGHTS”

AS AMENDED AND THE REGULATIONS OF THE GOVERNMENT OF THE RUSSIAN

FEDERATION NO. 55 of JANUARY 19, 1998 "LIST OF NON-FOOD PRODUCTS OF GOOD

QUALITY, ARE NOT SUBJECT TO RETURN OR EXCHANGE FOR SIMILAR GOODS OF

OTHER SIZE, SHAPE, DIMENSIONS, STYLE, COLOR OR CONFIGURATION" (AS AMENDED

ON OCTOBER 20, 1998), THE SELLER IS NOT OBLIGED TO TAKE BACK DEFECTIVE

EQUIPMENT IF IT FOR ANY REASONS HAS TURNED OUT TO BE UNSUITABLE FOR THE

BUYER.

Warranty card shall only be valid if completely filled, in the presence of the seal of the service

center or the seller, the signature of the consumer, and in the presence of an act of assembly,

issued by the dealer or service center DanVex (for dehumidifiers of AD series, requiring

professional installation).

www.danvex.fi 16

ВНИМАНИЕ!!!

CAUTION!!!

DanVex DEH-600wp User manual

Brand: DanVex

Model: DEH-600wp

Category: Dehumidifiers

Type: User manual

This manual is also suitable for

DEH-1000wp

Download PDF

report

DanVex DEH-600wp User manual

This manual is also suitable for

DanVex DEH-600wp User manual

Other documents