Rolls CT 1 User manual

Brand: Rolls

Model: CT 1

Category: Cable network testers

Type: User manual

This manual is also suitable for

CT 1

CABLE DETECTIVE

Cable Tester

Owners Manual

LIMITED WARRANTY

This product is warranted to the original consumer purchaser to be free

from defects in materials and workmanship under normal installation, use and

service for a period of one (1) year from the date of purchase as shown on the

purchaser’s receipt.

The obligation of Rolls Corporation under this warranty shall be limited

to repair or replacement (at our option), during the warranty period of any part

which proves defective in material or workmanship under normal installation,

use and service, provided the product is returned to Rolls Corporation, TRANS-

PORTATION CHARGES PREPAID. Products returned to us or to an authorized

Service Center must be accompanied by a copy of the purchase receipt. In the

absence of such purchase receipt, the warranty period shall be one (1) year from

the date of manufacture.

This warranty shall be invalid if the product is damaged as a result of

defacement, misuse, abuse, neglect, accident, destruction or alteration of the

serial number, improper electrical voltages or currents, repair, alteration or

maintenance by any person or party other than our own service facility or an

authorized Service Center, or any use violative of instructions furnished by us.

This one-year warranty is in lieu of all expressed warranties, obligations

or liabilities. ANY IMPLIED WARRANTIES, OBLIGATIONS, OR LIABILI-

TIES, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES

OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE,

SHALL BE LIMITED IN DURATION TO THE ONE YEAR DURATION OF

THIS WRITTEN LIMITED WARRANTY. Some states do not allow limitations

on how long an implied warranty lasts, so the above limitation may not apply to

you.

Salt Lake City, Utah

IN NO EVENT SHALL

WE BE LIABLE FOR ANY

SPECIAL, INCIDENTAL OR

CONSEQUENTIAL DAMAGES

FOR BREACH OF THIS OR

ANY OTHER WARRANTY,

EXPRESSED OR IMPLIED,

WHATSOEVER. Some states do

not allow the exclusion or

limitation of special, incidental or

consequential damages so the

above limitation or exclusion

may not apply to you. This

warranty gives you specific legal

rights, and you may also have

other rights which vary from state

to state.

CT 1 CABLE

DETECTIVE

• Tests 1/4", RCA, XLR

and MIDI cables

• Tests combinations of

the above

• Easy-to-read LED

indication

Any musician or sound person

knows how difficult it is to maintain

cables. The CT 1 provides an

efficient way to detect shorted or

open cables. The unit tests 1/4"

TS, 1/4" TRS, RCA, and XLR

cables. It tests MIDI cables, plus, it

will test combinations of the above.

CABLE DETECTIVE

CT 1

1/GND

2/TIP

3/RING

INTRODUCTION

Thank you for your purchase of the CT 1 CABLE DETECTIVE cable

tester. This unit was designed with the working musician and sound

person in mind. Read the following manual carefully to ensure proper

operation and a full understanding of all the CT 1 functions.

Tests for: Opens

Shorts

Intermittents

Crossed wires

DESCRIPTION

The CT 1 consists of two RCA jacks, two 1/4" jacks, two female XLR, two

male XLR jacks, and two MIDI jacks.

LED 1/GND: Indicates continuity between pins 1 of an XLR cable or MIDI

cable, or ground on an RCA or 1/4" cable.

LED 2/TIP: Indicates continuity between pins 2 of an XLR cable, or the tip

on an RCA or 1/4" cable.

LED 3/RING: Indicates continuity between pins 3 of an XLR cable or MIDI

cable, or the ring of a 1/4" cable.

To test RCA and 1/4" TS cables, plug each end of the cable into the proper jack

and wiggle the cable around at different points on the cable. Watch the 1 and 2

LEDs, if either LED is off, or goes on and off - the cable is bad.

The testing procedure for 1/4" TRS (stereo) and XLR cables is identical to the

above, except watch the 1, 2 and 3 LEDs.

Adapter type cables, such as 1/4" to XLR cables, may also be tested by plugging

each end into it's proper jack on either side of the line. Test as indicated above.

To test a MIDI cable, plug each end of the cable into the MIDI jacks and test as

described above. Watch the 1 and 2 LEDs, if either LED is off, or goes on and off

- the cable is bad.

NOTE: WHEN TESTING A 1/4" MONO TO RCA CABLE, CONNECT THE 1/4"

PLUG TO THE LEFT 1/4" JACK AND THE RCA TO THE RIGHT RCA JACK.

DUE TO A PARTICULAR CIRCUIT CONSIDERATION, TESTING VICE VERSA

(WITH THE 1/4" ON THE RIGHT AND THE RCA ON THE LEFT) WILL BE

INACCURATE.

TEST INDICATORS

NO LEDS = BAD CORD OR DEAD BATTERY

1 LED = SHORTED WIRES

2 LEDS = RCA, MIDI OR MONO CORD GOOD, OR CROSSED WIRES

IN STEREO & XLR CORDS

3 LED = GOOD STEREO 1/4" TRS, OR XLR CORD

CABLE DETECTIVE

CT 1

1/GND

2/TIP

3/RING

OPERATION

Insert one end of the cable to be tested on the left side of the line, located

in the middle of the CT 1, and the other side of the cable on the right side

of the line. See example below.

CABLE DETECTIVE

CT 1

1/GND

2/TIP

3/RING

122-Apr-1999

Document Number:

Date:

Sheet of

C A B L E T E S T E R C T 1

C T 1 . S C H

1 L E D = S H O R T E D W I R E S

2 L E D S = R C A , M O N O O R M I D I C O R D G O O D , O R C R O S S E D W I R E S I N S T E R E O & X L R C O R D S

M I D I T E S T

2 L E D S

B T 1

9 V

R 1

1 K

D 3

L E D

D 1

L E D

D 2

L E D

1 2

J 1

X L R F P C

J 7

P H O N E 1 / 4

J 5

R C A P C

1 2

J 4

X L R F P C

J 6

P H O N E 1 / 4

J 8

R C A P C

1 3

J 9

D I N 5

1 3

J 1 0

D I N 5

1 2

J 2

X L R J A C K M

J 3

X L R J A C K M

3 L E D S = G O O D S T E R E O 1 / 4 " T R S , O R X L R C O R D

N O L E D S = B A D C O R D O R D E A D B A T T E R Y

R O L L S C O R P O R A T I O N

5 1 4 3 S o u t h M a i n S t r e e t

S a l t L a k e C i t y , U T 8 4 1 0 7

Rolls CT 1 User manual

Brand: Rolls

Model: CT 1

Category: Cable network testers

Type: User manual

This manual is also suitable for

Download PDF

report

Rolls CT 1 User manual

This manual is also suitable for

Rolls CT 1 User manual

Related papers

Other documents