In case of smoke, strange noise or strange smell
from the unit:
Turn off the power switch immediately;
Disconnect the power plug from the power
outlet;
Contact your dealer or service centre. Never
attempt to make repairs yourself because this
could be dangerous.
High Voltage
Do not open
Risk of electronic shock, do not open.
Do not attempt to service this product yourself
as opening or removing covers may expose
you to dangerous voltage or other hazards.
Refer all servicing to qualified service personnel.
CAUTION
Important Safety Instructions
Important Safety Instructions and Maintenance
Never push objects of any kind into the set
through the cabinet slots as they may touch
dangerous voltage points or short-circuit parts that
could result in a fire or electric shock. Never spill
liquid of any kind on the set. Use special caution
in households where children are present. The
apparatus is not suitable for children under 3-year
to operate.
Power supply cords should be routed safety to
prevent life and property from dangerous with
damaged cord.
Mains plug is used as the disconnect device. It
shall remain readily operable and should not be
obstructed during intended use. To be completely
disconnected the apparatus from supply mains, the
mains plug of the apparatus shall be disconnected.
To reduce the risk of fire or electric shock, do not
expose this product to rain or moisture.
The apparatus shall not be exposed to dripping
or splashing and no objects filled with liquids,
such as vases, shall be placed on the apparatus.
To avoid the fire, no naked flame source,
such as lighted candles, should be
placed on the apparatus.
1
ENGLISH
Important Safety Instructions and Maintenance
Important Safety Instructions
Always turn the set off when it is not being used.
Unplug the apparatus from the AC outlet when it will
not be used for a long period of time. And when there
is a lightning, unplug the unit from the AC outlet
immediately. Never touch the antenna wire during
lightning.
An outside antenna system should not be located in
the vicinity of overhead power lines or other electric
light or power circuits, or where it can fall into such
power lines or circuits. When installing an outside
antenna system, extreme care should be taken to keep
from touching such power lines or circuits as contact
with them might be fatal.
Installation
The ventilation should not be impeded by covering the
ventilation opening with items, such as newspapers,
tablecloths, curtains, etc.
At least 10 cm space should be left around the
apparatus for sufficient ventilation.
The product should be situated away from heat
sources such as radiators,heat registers, stoves, or
other products (including amplifiers) that produce heat.
Place the apparatus in such a position that the screen
is not exposed to direct sunlight. It is best to have soft
indirect lighting while watching and avoid complete
dark environment and reflection from the screen as
these may cause eye fatigue.
Keep the product away from high magnetic field (i.e.
power-amplified power speaker) to avoid affecting the
tint;
2
Do not pull the plug out by the wire;
Never touch the plug with wet hands.
Excessive sound pressure from earphones and
headphones can cause hearing loss.
ENGLISH
3
Important Safety Instructions and Maintenance
Installation
Do not place this apparatus near water, for example,
near a bath tub, wash bowl, kitchen sink, or laundry
tub;in a wet basement;or a swimming pool;and
the like;
Cleaning
When the TV being moved in from cold place, it needs
some right time for dew inside unit evaporating fully
before turn on the unit;
Unplug this apparatus from the AC outlet before
cleaning. Do not use liquid cleaners or aerosol
cleaners. Use a damp cloth for cleaning;
Do not place the set on an unstable cart, stand, table
or shelf. The set may fall, causing serious personal
injury as well as damage to the product. Use only with
the cart, stand, tripod, bracket, or table specified by
the manufacturer, or sold with the apparatus. An
appliance and cart combination should be moved with
care. Quick stops, excessive force, and uneven
surfaces may cause the appliance and cart
combination to overturn.
To prevent injury, this apparatus must be securely
attached to the floor/wall in accordance with the
installation instructions.
Move
For your protection, please read this instruction completely, and keep this manual for
future reference.
WARNING
ENGLISH
4
General description5
Specifications and accessories6
Overview7
Basic operation10
External connection21
Trouble shooting23
Picture defects and countermeasures24
Basic operation
Contents
ENGLISH
5
General description
Feature:
l Zero X radiation complies to green environment protection requirement
l Auto tuning and fine tuning
l Two composite video input sockets
l One PC VGA input socket
l One YPbPr input socket
l One HDMI input socket (HDMI 1.3)
l One AV output socket
l One Headphone output socket
l Three audio input sockets
l Multi-language OSD
l Programmable TV sleep timer
l No-signal automatic power off function
l PC VGA mode: VGA, SVGA, XGA
l YPbPr mode: 480i, 480P, 576P, 720P, 1080i, 1080P
l HDMI mode: 480P, 576P, 720P, 1080i, 1080P
Specification
ENGLISH
Note:
1. Designs and specifications are subject to change without notice.
2. This model may not be compatible with features and/or specifications that may be
added in the future.
6
ENGLISH
QSG (Quick Start Guide)
Warranty card
Power cable
Note:
1. Designs and specifications are subject to change without notice.
2. This model may not be compatible with features and/or specifications that may be
added in the future.
5,000m
Altitude
Altitude
LE32W131
95W
780X236X550mm
780X41X496mm
9 kg
8.1 kg
9 Screws
Color active matrix LCD-LED display
Su ort base
pp
7
Overview
1
. TV/AV
Press this button to display the selected
signal source as main source.
4. MENU
Press this button to display OSD menu.
5. PROG /
Press these two buttons to select channel
or operate menu.
. Power indicator
Green: Normal playing status.
Red: Standby status.
2. IR remote sensor
Point remote control at this sensor to
conduct remote control.
3
6. VOL+/-
Press these two buttons to increase or
decrease the volume or operate menu.
7.
Press this button to enter standby mode
under normal play, and press this button
to enter normal play mode under standby
mode.
IR remote sensor
Power indicator
Menu
Program up/down
Volume up/down
Standby
Input select
ENGLISH
8
Overview
ENGLISH
9
Overview
Remote control
Loading batteries:
1)Remove the lid of the battery compartment.
2)Insert 2 size AAA batteries with polarities as indicated inside the compartment.
3)Replace the lid.
Note:
1)One loading of batteries will last 1 year under normal use.
2)If you don’t intend to use the remote control for a long period of time, remove
them to avoid damage due to leakage.
3)Do not mix old and new batteries, or different types.
4)Don’t throw the batteries into fire or water.
5) The batteries (battery pack or batteries installed) shall not be exposed to exces-
sive heat such as sunshine, fire or the like.
ENGLISH
10
Basic operation
Remote control introduction
1.INPUT
Select input source.
2.POWER
Turn your TV on and off.
3.0~9
Use these keys to input digit, letters and special characters.
4.INFO
Displays the program information.
5.RECALL
To swap to the previous program you wanted from current program.
6.SOUND
Select audio mode. Press the key repeatedly to choose one of the modes among
Normal, News, Music, Preference.
7.PICTURE
Select picture mode. Press the key repeatedly to choose one of the modes among
Normal, Sports, Mild, Preference.
8.SLEEP
TV will be switched off automatically at preset sleep time if you have set sleep
timer. Use your remote control to set the sleep timer. Press SLEEP button on the
remote control, then press this button again to set sleep timer: Off,15Min,30Min,
45Min,60Min,90Min,120Min.
Note: The sleep timer you have set will be canceled when the TV turns off or if a
power failure occurs.When SLEEP TIMER is 60 seconds only, left tunime will be
displayed on the screen, and any operation will cancel SLEEP TIMER function by
pressing any button on the remote control or on the unit.
9.ZOOM
Change the display mode press the key repeatedly to choose one of the modes
among Full, 4:3.
10.CCD
Select closed caption mode. Press the key repeatedly to choose one of the modes
among Off, CC1, CC2, CC3, CC4, Text1, Text2, Text3, Text4.
11.MTS
Select MTS sound system. Press the key repeatedly to choose one of the modes
among Mono, Stereo, Sap.
ENGLISH
11
Basic operation (to be continued)
12.FREEZE
Not available for this model.
13.AV
Swith to AV mode directly.
14.YPbPr
Switch to YPbPr mode directly.
15.PC
Switch to PC mode directly.
16.TV
Switch to TV mode directly.
17.HDMI
Switch to HDMI mode directly.
18.
Press this button to shut off sound of the TV temporarily, press again to restore
TV sound.
19.VOLq/p
Press these buttons to adjust TV volume.
20.PROGq/p
Press these buttons to change program upward or downward.
21.MENU
Display the main menu.
22.EXIT
Exit the menu.
23.Arrow buttons(q/p/t/u)
Press these buttons to move cursor up/down/left/right for menu.
24.OK
Validation key.
ENGLISH
12
PICTURE
AUDIO
CHANNEL
FUNCTIONSETTING
MENU
EXIT
SELECT
ADJUST
ALWAYSDURATION
OSD POSITION
SCREEN SAVER
LANGUAGEENGLISH
OFF
MID
Basic operation (to be continued)
Turning the TV On and Off
1.Plug the power cord into a power jack.
2.If TV is in standby mode, please press POWER
button on the remote control to turn it on. The
indicator will switch from red to green.
3.If you want to stop watching TV or go out for a
while, you can press POWER button on the re-
mote control. If you want to watch TV again, you
can press this button again.
4.Unplug the power cord when the TV will not be
used for a long period time.
Auto power-off
The TV will enter standby mode in 15 seconds
in PC mode, and in other modes it will enter
standby mode in 5 minutes when no signal
sleep is on.
Memorizing the Channels
Your TV can memorize all of the available
channels. After the available channels are
memorized, use PROGr/sbutton to browse
channels.
Language select
Before using TV, you can set the language:
1)Press MENU button on the remote control, then
press t/u Arrow button to select “Setting” menu
as following:
ENGLISH
13
Basic operation (to be continued)
2) Press p/qArrow button to enter the submenu and press t/u Arrow button to
select the language you desire.
Selecting input source
Press INPUT button on the remote control, then you can select input sources as
following:
Setting color system
In order to meet the color system in your country, you can set the color system as
following: Press q/p Arrow button to select “COLOR SYSTEM” under “CHANNEL”
menu,and then press t/u Arrow button to change video format as following:
Tuner setup
Press MENU button on the remote control, then press t/u Arrow button to select
“CHANNEL”:
1)SOURCE
Press q/p Arrow button to select “SOURCE”, and press t/u Arrow button to
select “Air” or “cable”.
2)CHANNEL
Press q/p Arrow button to select “CHANNEL” and press t/u Arrow button to
select the channel number.
3)COLOR SYSTEM
Press q/p Arrow button to select “COLOR SYSTEM” and press t/u Arrow
button to select the right color system.
PICTURE
AUDIO
CHANNEL
FUNCTIONSETTING
MENU
EXIT
SELECT
ADJUST
55.25MHZ
OFFSKIP
FINE TUNE
COLOR SYSTEM
CHANNEL
SOURCEAIR
2
AUTO
AUTO SEARCH
AFT
OFF
AUTO
PAL M PAL N NTSC M
TV AV1 HDMI PC
COMPONENT
AV2
ENGLISH
14
Basic operation (to be continued)
4)SKIP
Press q/p Arrow button to select “SKIP”, then press t/u Arrow button to select
“On” or “Off”. On: skip the channel; Off: not skip.
5)AFT
Press q/p Arrow button to select “AFT”, then press t/u Arrow button to select
“On” or “Off”.
6)FINE TUNE
In case of bad image or sound of TV program, you can use Fine Tune function
to obtain satisfied image or sound with operating steps as follows:
Press q/p Arrow button to select “FINE TUNE” and press t/u Arrow button to
conduct fine tuning from high frequency to low frequency or from low fre-
quency to high frequency till best picture or sound effect is obtained.
Note: Only if “AFT” is set to “OFF”,you can adjust the “FINE TUNE”.
7)AUTO SEARCH
Press q/p Arrow button to select “AUTO SEARCH”, then press u Arrow button
to start Auto Search:
TV will tune automatically and all programs found will be saved. Please don’t
interrupt it.
Note:
i) If you use the TV for the first time, you must use “AUTO SEARCH” to search
and memorize all channels.
ii) If your TV is not in TV input state, you must switch it to TV state at first.
iii) If you want to stop the process of “AUTO SEARCH”, just press MENU button
to exit.
AIR
AUTO SEARCH
CH: 1
ENGLISH
15
Adjusting the Picture
Press MENU button on the remote control, then press t/u Arrowbutton to select
“PICTURE” menu.
1) Adjusting Picture Mode
Press q/p Arrow button to select “PICTURE MODE”, and press t/u Arrow
button to adjust picture mode to your desire.
Note: “BRIGHTNESS”, “CONTRAST”, “COLOR” adjusting are only available in
preference mode.
2)Adjusting the Brightness of picture
Press q/p Arrow button to select “BRIGHTNESS”, and press t/u Arrow button
to adjust brightness to your desire.
3)Adjusting the Contrast of picture
Press q/p Arrow button to select the “CONTRAST”, then press t/u Arrow
button to set contrast to your desire.
4)Adjusting the Tint of picture
Press q/p Arrow button to select the “TINT”, then press t/u Arrow button to set
tint to your desire.
Note: Only available in NTSC.
5)Adjusting the Color of picture
Press q/p Arrow button to select the “COLOR”, then press t/u Arrow button to
set saturation to your desire.
6)Adjusting the Sharpness of picture
Press q/p Arrow button to select the “SHARPNESS”, then press t/u Arrow
button to set sharpness to your desire.
7)Adjusting the Backlight of picture
Press q/p Arrow button to select the “BACKLIGHT”, then press t/u Arrow
button to set backlight to your desire.
Note:Backlight function is only available for models with this function.
8)Adjusting the Color Temp of picture
Press q/p Arrow button to select the “COLOUR TEMP.” , then press t/u Arrow
button to set colour temperature to your desire.
9)Adjusting the Scale Mode of picture
Press q/p Arrow button to select the “SCALE”, then press t/u Arrow button to
set scale mode to your desire.
Note: It is useless under no signal mode.
Basic operation (to be continued)
PICTURE
AUDIO
CHANNEL
FUNCTIONSETTING
MENU
EXIT
SELECT
ADJUST
PICTURE MODEPREFERENCE
FULL
NORMAL
BRIGHTNESS
CONTRAST
COLOR
SHARPNESS
BACKLIGHT
COLOUR TEMP.
SCALE
50
50
0
50
50
TINT
50
ENGLISH
16
PICTURE
AUDIO
CHANNEL
FUNCTIONSETTING
MENU
EXIT
SELECT
ADJUST
ALWAYSDURATION
OSD POSITION
SCREEN SAVER
LANGUAGEENGLISH
OFF
MID
Adjusting the Sound
Press MENU button on the remote control, then press t/uArrow button to select
“AUDIO ” menu.
1)Adjusting Sound Mode
Press q/p Arrow button to select “SOUND MODE”, use t/u Arrow button to
adjust sound mode.
2)Adjusting the Equalizer
Press q/p Arrow button to select “EQUALIZER”, use t/u Arrow button to adjust
the frequency.
3)Adjusting Balance of sound
Press q/p Arrow button to select “BALANCE”, use t/u Arrow button to adjust
sound balance.
4)Adjusting AVL
Press q/p Arrow button to select “AVL” and press t/u Arrow button to set it
“ON” or “OFF”.
5)Adjust MTS
Press q/p Arrow button to select “MTS”, use t/u Arrow button to adjust to your
desired.
Note: Only available in TV.
OSD Setup
Press MENU button on the remote control and press t/u Arrow buttonto select
“SETTING” menu.
Basic operation (to be continued)
PICTURE
AUDIO
CHANNEL
FUNCTIONSETTING
MENU
EXIT
SELECT
ADJUST
SOUND MODEPREFERENCE
MONO
OFF
EQUALIZER
BALANCE
MTS
0
AVL
ENGLISH
17
1)OSD Language
Press q/p Arrow button to select “LANGUAGE” and press t/u Arrow button to
select language you desire.
2)Adjusting SCREEN SAVER
Press q/p Arrow button to select “SCREEN SAVER” and press t/u Arrow
button to set screen saver.
3)Adjusting OSD Position
Press q/p Arrow button to select “OSD Position” and press t/u Arrow button to
set position of OSD.
4)Adjusting OSD Timer
Press q/p Arrow button to select “DURATION”, Press t/u Arrow button to se-
lect one time from the following times: 5s,10s,15s and always.
Function setup
Press MENU button on the remote control or TV side panel, press t/u Arrow button
to select “FUNCTION” menu.
1)SLEEP TIMER
Please refer to page 10.
2)NO SIGNAL SLEEP
Refer to page 12 “Auto power-off”.
3)OPC
Press q/p Arrow button to select “OPC” in “Function” menu. press t/u Arrow
button to set it “ON” or “OFF” or “DEMO”.
Note: Not available in VGA.
4) CLOSED CAPTION
Press q/p Arrow button to select “CLOSED CAPTION” in “Function” menu.
Press the key repeatedly to choose one of the modes among Off, CC1, CC2,
CC3, CC4, Text1, Text2, Text3, Text4.
Basic operation (to be continued)
PICTURE
AUDIO
CHANNEL
FUNCTIONSETTING
MENU
EXIT
SELECT
ADJUST
OFFCLOSED CAPTION
PARENT CONTROL
OPC
NO SIGNAL SLEEP
SLEEP TIMEROFF
ON
ON
ENGLISH
18
Basic operation (to be continued)
5)Parent Control
In “Function” menu, press q/p Arrow button to select “Parent Control”,press t/
u Arrow to enter the input password menu. Input the password to enter the
submenu(the default password is 0000 and omnipotent password is 1980).
(1) Change Password
1.Press q/p Arrow button to select "CHANGE PASSWORD" option.
2.Press t/u Arrow button and input a new password twice to change the
password.
(2) Channel Lock
1.Press q/pArrow button to select "CHANNEL LOCK" option.
2.Press t/u Arrow button to enter the submenu.
l Source
1.Display the current channel source.
PICTURE
AUDIO
CHANNEL
FUNCTIONSETTING
MENU
EXIT
SELECT
ADJUST
CHANNEL INPUT
SOURCEAIR
_ _ _
CLEAR ALL
_ _ _
_ _ _
_ _ _
_ _ _
_ _ _
_ _ _
_ _ _
_ _ _
_ _ _
PICTURE
AUDIO
CHANNEL
FUNCTIONSETTING
MENU
EXIT
SELECT
ADJUST
VIDEO LOCK
CHANNEL LOCK
CHANGE PASSWORD
OFF
ENGLISH
19
PICTURE
AUDIOWINDOWFUNCTIONSETTING
MENU
EXIT
SELECT
ADJUST
PICTURE MODEPREFERENCE
FULL
WARM
BRIGHTNESS
CONTRAST
BACKLIGHT
COLOUR TEMP.
SCALE
50
50
50
l Channel Input
1.Press q/p Arrow button to select "CHANNEL INPUT" function.
2.Input the channel number you want to lock and press OK key to confirm,the
channel number will be add to the list below.
3.If you want to unlock a channel, press t/u Arrow button to select the channel
number in the list and press OK key to delete it.
Note: You can lock 9 channels in "AIR" or "CABLE" source.
l Clear All
1.Select a source you want to clear in "SOURCE" function.
2.Press q/p Arrow button to select "CLEAR ALL" function.
3.Press u Arrow button to clear the channel list in the source you select.
(3) Video Lock
1.Press q/p Arrow button to select "VIDEO LOCK" option.
2.Press t/u Arrow button to select "VIDEO" , "VIDEO+" or "OFF".
l Video: Lock all sources except TV.
l Video+: Lock Channel 3 and channel 4 of TV and all other sources.
l Off: Close "VIDEO LOCK" function and all sources are available.
Note: If the sources have locked, the key in Remote is not available in AV, TV,
COMPONENT, PC,HDMI input.
PC Adjust
1.Picture
When the TV is in PC mode, press MENU button on the remote control panel.
Presst/u Arrow button to select “PICTURE”.
The method to adjust Brightness, contrast, Backlight, color Temp, and scale, please
refer to “Adjusting the Picture”.
Basic operation (to be continued)
ENGLISH
20
Basic operation (to be continued)
2.Window
This TV supports no higher than 60Hz under PC mode, so please set the refresh
rate of PC to 60Hz. If the frequency is higher than 60Hz, the screen may flicker.
When the TV is in PC mode, press MENU button on the remote control. Press t/u
Arrow button to select “WINDOW”.
1)Adjusting picture H-Position
Press q/p Arrow button to select “H-POSITION” and press t/u Arrow button to
set horizontal position of picture.
2)Adjusting picture V-Position
Press q/p Arrow button to select “V-POSITION” and press t/u Arrow button to
set vertical position of picture.
3)Adjusting Clock
When PC is connected to TV set because of the difference of PC parameter,you
should adjust the “CLOCK” item in “WINDOW” menu until you get a good picture.
4)Adjusting Phase
When PC is connected to TV set because of the difference of PC parameter,you
should adjust the “PHASE” item in “WINDOW” menu until you get a good picture.
5)Auto Adjust
If there are unexpected problems happened when you adjust the items, you can
select the “AUTO ADJUST” and press u Arrow button, the TV set will resume the
original settings.
Note: Only “H-Position” and “V-Position” are available for YPBPR mode.
PICTURE
AUDIO WINDOWFUNCTIONSETTING
MENU
EXIT
SELECT
ADJUST
PHASE
AUTO ADJUST
CLOCK
V-POSITION
H-POSITION
100
100
100
0
PICTURE
AUDIO WINDOWFUNCTIONSETTING
MENU
EXIT
SELECT
ADJUST
V-POSITION
H-POSITION
100
100
ENGLISH
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/
