Livex Lighting 51037-91 Operating instructions

Livex Lighting
Brand
Livex Lighting
Model
51037-91
Type
Operating instructions

This manual is also suitable for

Livex Lighting 51037-91 is a versatile and stylish lighting fixture that can elevate the ambiance of any room. With its adjustable height and multiple light sources, it offers customizable illumination to suit your specific needs. The fixture's elegant design, featuring a round frame adorned with sparkling crystals, adds a touch of glamour to any setting. Whether you're seeking ambient lighting for a cozy living room or task lighting for a dedicated workspace, the Livex Lighting 51037-91 is an excellent choice.

Livex Lighting 51037-91 is a versatile and stylish lighting fixture that can elevate the ambiance of any room. With its adjustable height and multiple light sources, it offers customizable illumination to suit your specific needs. The fixture's elegant design, featuring a round frame adorned with sparkling crystals, adds a touch of glamour to any setting. Whether you're seeking ambient lighting for a cozy living room or task lighting for a dedicated workspace, the Livex Lighting 51037-91 is an excellent choice.

ASSEMBLING & INSTALLATION INSTRUCTIONS
The drawing shown may not exactly match the product enclosed.
However, the installation instructions do apply to this product.
51033 51034 51037
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.
ATTENTION! COUPER LE COURANT AU FUSIBLE OU UN DISJONCTEUR.
ASSEMBLING THE FIXTURE (Fig.1)
1. Shut off the power at the circuit breaker box. Remove old fixture and all
hardware from Junction Box.
2. Carefully unpack your new fixture and lay out all the parts on a clear area. Take
care not to lose any small parts necessary for installation.
3. Slide the electrical wires through the tube(F)/(E)/(D)/(C) and canopy(A) .
4. Raise the tube (F) to top screw pipe of shade (H), raise the tube (E) ,tube
(D) ,tube (C) to the screw pipe nipple in order , then by turning it clockwise until
tight. Open the link(B), hooked the canopy(A) and the end loop of lamp body,
close the link(B).
5. Install the light bulbs in accordance with the fixture specifications NOTE: DO
NOT EXCEED THE SPECIFIED WATTAGE!
6. Please see the Fig 1.1 (round frame Top View). Loosen the tie crystal
cluster of cord and organize appropriate. Raise the acrylic plate(I), round frame
(J) to the bottom of the lamp body (H), aligning the center hole with pipe nipple
and screw it with the finial (M).
7. Thread the two mounting screws into the pre-drilled holes in the Mounting plate
spaced the same distance apart as the holes in the canopy (A).
8. Attach the Mounting plate to the Junction Box with the two Junction Box screws
as shown. The side of the Mounting plate marked "GND" must face to out. The
junction box is not include.
9. While holding the fixture lamp towards the ceiling , connect the electrical wires
as Shown in Fig.2, making sure that all wire nuts are secured. You may have to
wrap the connections with electrical tape. If your outlet has a ground wire (green
or bare copper), connect the fixture ground wire to it. Otherwise connect
fixture’s ground wire directly to the Mounting plate with the green screw
provided. After wires are connected, tuck them carefully inside the Junction
Box.
10. Raise the canopy (A) on to the Junction box, aligning screws on mounting
plate with mounting holes in canopy and lock it securely with the ball nuts.
11. Raise the end grapnel of the crystal cluster(K) hooked the middle ring of round
frame(J); raise the end grapnel of the crystal cluster(L) hooked the inside ring
of round frame(J); raise the end grapnel of the crystal cluster(G) hooked the
side hole of tube(F).
Your installation is now complete. Return power to the junction
box and test the fixture.
Mounting plate
Mounting screw
Fixture
Junction Box
(Not include)
Ground Wire
Ground Wire
K
L
Middle
ring
Inside
ring
Fig 1.1
Round
frame(
J)
FIXTURE
WIRES
Black or
Smooth
HOUSE
WIRES
Black(Hot)
FIXTURE
WIRES
White or
Ribbed
FIXTURE
WIRES
Bare
Copper
(Ground)
HOUSE
WIRES
White
(Neutral)
HOUSE
WIRES
Green or Bare
Copper(Ground)
Thank you for purchasing a LIVEX product.
Need assistance with parts or assembly? Please call customer service at: 800-761-8056
Or visit us online at: WWW.LIVEXLIGHTING.COM
©COYRIGHT ALL RIGHTS RESERVED.LIVEX LIGHTING,INC. DOC20151251033
FIG.2
FIG.1
  • Page 1 1

Livex Lighting 51037-91 Operating instructions

Livex Lighting
Brand
Livex Lighting
Model
51037-91
Type
Operating instructions
This manual is also suitable for

Livex Lighting 51037-91 is a versatile and stylish lighting fixture that can elevate the ambiance of any room. With its adjustable height and multiple light sources, it offers customizable illumination to suit your specific needs. The fixture's elegant design, featuring a round frame adorned with sparkling crystals, adds a touch of glamour to any setting. Whether you're seeking ambient lighting for a cozy living room or task lighting for a dedicated workspace, the Livex Lighting 51037-91 is an excellent choice.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents