Draw-Tite 75401† Installation guide

Brand: Draw-Tite

Model: 75401†

Type: Installation guide

This manual is also suitable for

75401

Draw-Tite 75401† is a weight-distributing and weight-carrying hitch designed for the 2005-2006 Subaru B9 Tribeca. It is advertised to have a maximum gross trailer weight of 4000 lbs and a maximum tongue weight of 400 lbs when used for weight distribution, and a maximum gross trailer weight of 3500 lbs and a maximum tongue weight of 350 lbs when used for weight carrying. The hitch is made of GR5 steel and has a black powder coat finish. It comes with all necessary hardware for installation.

Features

Weight-distributing and weight-carrying capabilities
Maximum gross trailer weight of 4000 lbs (weight distributing) or 3500 lbs (weight carrying)

Features

Weight-distributing and weight-carrying capabilities
Maximum gross trailer weight of 4000 lbs (weight distributing) or 3500 lbs (weight carrying)

Installation Instructions

Subaru B9 Tribeca

Part Numbers:

44535

75401

87407

Hitch Shown In Proper Position

Equipment Required:

Wrenches: 11/16, 3/4

Drill Bits: None

1. Lower the spare tire from the underside of the vehicle.

2. Remove the two (2) plastic fascia tabs (do not discard).

3. Using the 3/8 wire pull, insert the 3/8 Carriage bolts through the end of the inside portion of the vehicle bumper structure and

through the existing slots.

4. Raise hitch into position and loosely install 3/8 Conical toothed washers and 3/8 Hex nuts as shown above.

5. Using the ½ wire pull insert the ½ Carriage bolts and ¼ X 1.00 X 3.00 Blocks through the vertical holes in the vehicle frame

structure to the existing holes in the vehicle frame rails and through the receiver.

6. Install ½ Conical toothed washers and ½ hex nuts.

7. Tighten all fasteners to the required torque specifications.

8. Reinstall the two (2) plastic fascia tabs removed in installation step 2.

9. Raise spare tire back into position.

Tighten all ½-13 GR5 fasteners with torque wrench to 75 Lb.-Ft.

Rev. B01-24-0675401NSheet 1 of 3

z 2005, 2006 Cequent Towing Products

½-13 X 2.00 GR5 Carriage BoltQty. (2)

½Hex NutQty. (2)

3/8 Hex NutQty. (2)

½ Conical Toothed WasherQty. (2)

3/8 Conical Toothed WasherQty. (2)

¼ X 1.00 X 3.00 BlockQty. (2)

3/8-16 X 1.25 GR5 Carriage BoltQty. (2)

Tighten all 3/8-16 GR5 fasteners with torque wrench to 30 Lb.-Ft.

Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to

prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working

beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.

This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5

and SAE J684.

Fastener Kit: 75401F or 87407F

Do Not Exceed Lower of Towing Vehicle

Manufacturer’s Rating or

3503500

Weight Carrying

Ball Mount

4004000

Weight Distributing

Max Tongue

WT (LB)

Max Gross