KRAUS KCU-241 User manual

Brand
KRAUS
Model
KCU-241
Type
User manual

This manual is also suitable for

INSTALLATION MANUAL
Elavo™ White Ceramic Small
Rectangular Undermount Bathroom
Sink w/ Overow
KCU-241
www.kraususa.com I toll free: 1.800.775.0703 I © 2014-2015 Kraus USA Inc. I REV. August 13, 2015
2
Thank you for purchasing Kraus
We would like to take this opportunity to thank you for your business with Kraus
USA. It is our sincere hope that you are completely satised with your experience.
We welcome any questions or comments you may have, and will be glad to assist
you in the future.
For more information about Kraus products, please visit our website at:
www.kraususa.com
Please register your new Kraus product at the following web address in order to
activate the warranty and receive the full benet of customer support:
www.kraususa.com/registration
Sincerely,
Kraus Customer Service Department
3
Prior to Installation:
• Make sure that you have all necessary parts by checking the parts list. If any part is
missing or damaged, please contact Kraus Customer Service at 800-775-0703 for a
replacement.
• Inspect the sink prior to installation to make sure it has not been cracked or
chipped during shipping
• Use the cut-out template provided by Kraus
• Observe all plumbing and building codes according to your state requirements
• Additional oor and wall preparation may be required to avoid damaging the sink
WARNING: This product is fragile and can break, chip, or cause injury if handled
recklessly. Please consult with a professional when installing
4
• Cut-Out Template • Mounting Hardware
NOTE: Specialized tools may be necessary to install Kraus Ceramic Undermount sinks
with countertop materials other than wood, marble, or granite
Tools you will need:
Scissors Screwdriver
Safety Goggles
Putty KnifePhillips Screwdriver
Drill
Tape Measure
Silicone Adhesive Jig Saw
Pencil
Adjustable wrench
Phillips screwdriver
Tools You Will Need
Hex wrench Silicone Sealant
A
I
D
J
F
B
G
C
H
E
Adjustable wrench
Phillips screwdriver
Tools You Will Need
Hex wrench
Silicone Sealant
A
I
D
J
F
B
G
C
H
E
Parts List (Included)
5
20.86”L x 14.37”W x 8.1”H
Side ViewFront View
KHU15 & KHU15C
14.5” x 18.5” x 10”
Bottom ViewTop View
Dimensions
16.26”
413mm
16.26”
413mm
6.69”
170mm
Ø1.77”
45mm
Ø1.77”
45mm
16.54”
420mm
17.91”
455mm
17.00”
432mm
20.87”
530mm
23.27”
591mm
23.62”
600mm
14.76”
375mm
16.26”
413mm
17.24”
438mm
16.54”
420mm
5.51”
140mm
18.11”
460mm
5.51”
140mm
5.51”
140mm
16.14”
410mm
Ø1.77”
45mm
Ø1.77”
45mm
Ø1.77”
45mm
Ø1.77”
45mm
Ø1.77”
45mm
Ø1.77”
45mm
Ø1.77”
45mm
Ø1.77”
45mm
Ø1.77”
45mm
Ø16.34”
415mm
Ø13.7”
348mm
5.24”
133mm
7.52”
191mm
8.11”
206mm
5.71”
145mm
17.00”
432mm
7.68”
195mm
7.52”
191mm
8.11”
206mm
14.37”
365mm
17.32”
440mm
21.26”
540mm
6
1. Cut paper template
2. Trace template
• Use scissors to cut along the inside line of the paper template
• Compare cut template with sink to ensure proper size
• Place the cut-out template in the desired location on the countertop and
trace with a pencil
• Mark the faucet hole centerline on the countertop using the vertical line
in the center of the paper template
NOTE: Make sure clearance is suitable for backsplash, faucet, and plumbing for the sink
Clip Location
Rim of Lavatory
Cut Along This Line
11.61” (295mm)
17.7” (450mm)
Model No. KCU-251
Allow a minimum of 4.5” (114.3mm)
from wall for faucet placement
clearance before cutting
NOTE: When plotting template
full size: Make sure horizontal
and vertical dimensions match
the dimensions labeled in the
template
12.9” (328mm)
19.9” (506mm)
Clip Location
Rim of Lavatory
Cut Along This Line
Clip Location
Rim of Lavatory
Cut Along This Line
11.61” (295mm)
17.7” (450mm)
Model No. KCU-251
Allow a minimum of 4.5” (114.3mm)
from wall for faucet placement
clearance before cutting
NOTE: When plotting template
full size: Make sure horizontal
and vertical dimensions match
the dimensions labeled in the
template
12.9” (328mm)
19.9” (506mm)
Clip Location
Rim of Lavatory
Cut Along This Line
7
3. Cut countertop
• Cut the countertop opening by carefully following the pencil line traced
from the template
Flushed/Zero Reveal
3/8“ Positive Reveal
1/8“ Negative Reveal
DETERMINE REVEAL TYPE
Step1
Step2
Step3
Step4
Step6
Step5
Step7
Step8 Step9
Determine location for mounting brackets; space
1/2"
(13mm)
3/8
1/2
Centerline
3/8”POSITIVE
1/8”NEGATIVE
FLUSHED/ZERO
Flushed/Zero Reveal
3/8“ Positive Reveal
1/8“ Negative Reveal
DETERMINE REVEAL TYPE
Step1
Step2
Step3
Step4
Step6
Step5
Step7
Step8 Step9
Determine location for mounting brackets; space
1/2"
(13mm)
3/8
1/2
Centerline
3/8”POSITIVE
1/8”NEGATIVE
FLUSHED/ZERO
Flushed/Zero Reveal
3/8“ Positive Reveal
1/8“ Negative Reveal
DETERMINE REVEAL TYPE
Step1
Step2
Step3
Step4
Step6
Step5
Step7
Step8 Step9
Determine location for mounting brackets; space
1/2"
(13mm)
3/8
1/2
Centerline
3/8”POSITIVE
1/8”NEGATIVE
FLUSHED/ZERO
NOTE: Please use the appropriate saw that best ts your countertop
material
Clip Location
Rim of Lavatory
Cut Along This Line
11.61” (295mm)
17.7” (450mm)
Model No. KCU-251
Allow a minimum of 4.5” (114.3mm)
from wall for faucet placement
clearance before cutting
NOTE: When plotting template
full size: Make sure horizontal
and vertical dimensions match
the dimensions labeled in the
template
12.9” (328mm)
19.9” (506mm)
Clip Location
Rim of Lavatory
Cut Along This Line
8
4. Install anchors
NOTE:
• Please check epoxy directions for curing time
• Please tap brass nut anchors lightly with hammer
• Flip countertop over and place on a foam pad for protection. Use cutout
template to mark the anchor placement on the countertop. Drill 5/16”
diameter x 3/8” deep hole in countertop
• Place epoxy in the drilled hole. Insert brass nut anchors into the drilled
hole and wait until the epoxy cures
Clip Location
12.4” (315mm)
15.6” (395mm)
Rim of Lavatory
Cut Along This Line
Clip Location
12.4” (315mm)
15.6” (395mm)
Rim of Lavatory
Cut Along This Line
Clip Location
Rim of Lavatory
Cut Along This Line
11.61” (295mm)
17.7” (450mm)
Model No. KCU-251
Allow a minimum of 4.5” (114.3mm)
from wall for faucet placement
clearance before cutting
NOTE: When plotting template
full size: Make sure horizontal
and vertical dimensions match
the dimensions labeled in the
template
12.9” (328mm)
19.9” (506mm)
Clip Location
Rim of Lavatory
Cut Along This Line
Clip Location
Rim of Lavatory
Cut Along This Line
11.61” (295mm)
17.7” (450mm)
Model No. KCU-251
Allow a minimum of 4.5” (114.3mm)
from wall for faucet placement
clearance before cutting
NOTE: When plotting template
full size: Make sure horizontal
and vertical dimensions match
the dimensions labeled in the
template
12.9” (328mm)
19.9” (506mm)
Clip Location
Rim of Lavatory
Cut Along This Line
9
NOTE: Use acetone or rubbing alcohol to remove any excess sealant
5. Install sink
• Use a bead of clear silicone (or preferred adhesive) around the rim of
the sink. Check the alignment of the sink to the opening in the countertop.
Place sink over cutout hole and press rmly
• Attach mounting hardware to secure bowl. Remove excess sealant from
inside lip
• Allow sealant to set for 30 – 60 minutes
6. Install plumbing xtures
• Connect drain to sink. Connect trap to drain. Connect water supply
connections to faucet according to manufacturer’s instructions
• Run water into sink and check for leaks
Clip Location
Rim of Lavatory
Cut Along This Line
14.25” (362mm)
14.25” (362mm)
Clip Location
Rim of Lavatory
Cut Along This Line
11.61” (295mm)
17.7” (450mm)
Model No. KCU-251
Allow a minimum of 4.5” (114.3mm)
from wall for faucet placement
clearance before cutting
NOTE: When plotting template
full size: Make sure horizontal
and vertical dimensions match
the dimensions labeled in the
template
12.9” (328mm)
19.9” (506mm)
Clip Location
Rim of Lavatory
Cut Along This Line
Clip Location
Rim of Lavatory
Cut Along This Line
11.61” (295mm)
17.7” (450mm)
Model No. KCU-251
Allow a minimum of 4.5” (114.3mm)
from wall for faucet placement
clearance before cutting
NOTE: When plotting template
full size: Make sure horizontal
and vertical dimensions match
the dimensions labeled in the
template
12.9” (328mm)
19.9” (506mm)
Clip Location
Rim of Lavatory
Cut Along This Line
Clip Location
Rim of Lavatory
Cut Along This Line
11.61” (295mm)
17.7” (450mm)
Model No. KCU-251
Allow a minimum of 4.5” (114.3mm)
from wall for faucet placement
clearance before cutting
NOTE: When plotting template
full size: Make sure horizontal
and vertical dimensions match
the dimensions labeled in the
template
12.9” (328mm)
19.9” (506mm)
Clip Location
Rim of Lavatory
Cut Along This Line
10
Codes/Standards Applicable:
KRAUS LIMITED LIFETIME WARRANTY
This product has been manufactured and tested to the highest quality standards by
Kraus USA Inc. (“Kraus”). We offer our customers thoughtfully crafted fixtures & accesso-
ries, engineered for enduring performance over years of use.
WHO IS COVERED BY THE WARRANTY
This warranty extends to the original purchaser only. This warranty is not transferable,
between homes or owners and is only applicable to residential use.
WHAT IS COVERED BY THE WARRANTY
Kraus warranties this product against defects due to material or craftsmanship error
during the warranty period: Kraus will provide replacement parts at no charge, or at
its option, replace any product or part of the product that is deemed defective, under
normal installation, use, service and maintenance. If Kraus is unable to provide a replace-
ment and repair is not practical or cannot be made in timely fashion, Kraus may elect to
refund the purchase price in exchange for the return of the product.
CONDITIONS AND EXCLUSIONS
Like other home fixtures, Kraus products will require light maintenance to ensure proper
function. We provide you with complete knowledge to perform this maintenance and
can also recommend resources if you are unable to fulfill this service.
A. Kraus will not be responsible for product failures due to lack of maintenance or proper
use. Please read your care and maintenance documentation to determine the limits of
proper use.
B. The original sales receipt, order number, and/or proof of purchase must be presented
at the time of the warranty claim, without exception, for this warranty to be applied to all
Kraus products.
C. Kraus recommends installing all Kraus products with a licensed, professional plumber.
Kraus will not be held responsible for any damage or product failure due to improper
installation, misuse, or failure to use a licensed professional. Please read your care and
maintenance documentation to determine the limits of proper use.
D. Commercial use will automatically void this warranty.
E. This warranty is not applicable to Kraus products purchased from an unauthorized
seller. For a complete list of authorized sellers please visit http://www.kraususa.com/
where-to-buy.html
11
HELP LINE
Our customer service hours are Monday – Friday, 9am – 8pm EST.
Be sure to visit our website at www.kraususa.com
NON-APPLICABILITY OF THIS WARRANTY
By the purchase and use of our products, you agree that Kraus is not liable for incidental,
consequential or special damages associated with the return, replacement, installation or
use of your product. This includes freight costs, cartridge replacement, labor, travel time,
lost profit, home damages and other contingent liabilities and costs (including, without
limitation, costs associated with experts, investigations, analyses, attorneys and other
professionals and services). The Kraus warranty is a comprehensive and explicit limit of
liability, and all items outside of it are not addressable by or the responsibility of Kraus.
Certain states have variances regarding implied warranties and in those situations we
remain fully compliant.
KRAUS USA Inc. makes no implication that products comply with any or all local building
or plumbing codes. It is the consumer’s responsibility to determine local code compli-
ance. This warranty extends to the original purchaser and first consumer.
If you are a homeowner please contact a Kraus Customer Service Representative at:
Kraus USA, Inc.
12 Harbor Park Drive
Port Washington, NY 11050
Toll-free 800-775-0703
[email protected]
If you are a plumbing contractor or trade professional please contact a Kraus Pro
Representative at:
Kraus USA, Inc.
12 Harbor Park Drive
Port Washington, NY 11050
516-801-8955
[email protected]
If you are an Authorized Partner please contact a Partner Support Representative at:
Kraus USA, Inc.
12 Harbor Park Drive
Port Washington, NY 11050
516-801-8954
Partnersupport@kraususa.com
In requesting warranty service, please be ready to provide:
1. Proof of purchase.
2. A description of the problem.
www.kraususa.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

KRAUS KCU-241 User manual

Brand
KRAUS
Model
KCU-241
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents