CEILING FAN
F8254&F8254SN110V
Installation & Operating Instructions for the
Parrotuncle Owner's Installation ,Manual
WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER
Installation & Operating Instructions for the
Parrotuncle Owner's Installation ,Manual
WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER
F8254&F8254SN110V
Thank you for purchasing this quality product. To ensure correct function and safety, please read and save all
instructions before using the product
To avoid possible electric shock, turn off the electricity at the main fuse box or circuit panel before you begin the fan installation or
before servicing the fan or installing accessories.
Read all instructions and safety information carefully before installing your fan and save these instructions.
Make sure all electrical connections comply with local codes or ordinances and the National Electrical Code. If you are unfamiliar with
electric wiring, please use a qualified and licensed electrician.
Make sure you have a location selected for your fan that allow clear space for the blades to rotate,and at least seven (7) feet of clearance betweem
the floor andthe fan blade tips. The fan should be mounted at leaet thirty (30) inches ftom walls or other upright structures.
WARNING: The outlet box and ceiling support joist used must be securely mounted, and capable of supporting at least 100 pounds. To
reduce the risk of fire, electric shock or personal injury, mount to the outlet box marked acceptable for fan supported and use mounting
screws provided with the outlet box. The box must be supported directly by the building structure.
WARNING: To reduce the risk of fire, electric shock or personal injury, mount to outlet box marked “acceptable for fan support” and use mounting
screws provided with the outlet box most outlet boxes commonly used for the support of lighting fixtures are not acceptable for fan
support and may need to be replaced. Consult a qualified electrician if in doubt.
Electrical diagrams are for reference only. Light kits that are not packed with the fan must UL listed and marked suitable for use with the
model fan you are installing. Switches must be UL. general use switches. Refer to the instructions packaged with the light kits and
switches for proper assembly.
After installation is complete, check that all connections are absolutely secure.
After making electrical connections, spliced conductors should be turned upward and pushed carefully up into outlet box. The wires
should be spread apart with the grounded conductor and the equipment-grounding conductor on one side of the outlet box.
WARNING: To reduce the risk of electrical shock and fire, do not use this fan with any solid-state fan speed control device, or rheostat.
Do not separate the reverse switch until the fan has come to a complete stop.
Do not insert anything into the fan blades while they are rotating.
WARNING: To reduce the risk of personal injury, do not bend the blade brackets (also referred to as “flanges”) during assembly or after
installation. Do not insert objects in the path of the blades.
To avoid personal injury or damsge to the fan and other items,be cautious when working around or cleaning the fan.
Do not use water or detergent when cleaning the fan or fan blades. A dry dust cloth or lightly dampened cloth will be suitable for most cleaning.
1.
2.
3.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
NOTE: The important safety precautions and instructions appearing in the manual are not meant to cover all possible conditions and situations that may
mayoccur. It must be understood that common sense and caution are necessary factors in the nstallation and operation and operation of this fan.
NOTE: This product is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities are
different or are impaired, or lack of experience or knowledge, unless such persons are supervised or trained to operate the appliance
by a person responsible for their safety.
NOTE: Children should be supervised to ensure that they do not use appliances as a toy.
THANK YOU FOR YOUR PURCHASE
SAFETY TIP
4.
TECHNICAL INFORMATION
SKU Rated Voltage
F8254110V
110-120 VAC 15W
3*G 9 MAX.2W
Rated power(motor) Light
F8254SN110V
110-120 VAC 15W
3*G 9 MAX.2W
Wood screws (4PCS)
washer (4PCS)
Round hanging plate
Pls check whether above accessories are completed or not?Yes,and install.
REMOTE CONTROL(1PCS)
Installation & Operating Instructions for the
Parrotuncle Owner's Installation ,Manual
WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER
F8254&F8254SN110V
Plastic wire nut (3PCS)
spring washer
(4PCS)
Mounting screws (2PCS)
Iron mesh lampshade
STOP
I
Installation & Operating Instructions for the
Parrotuncle Owner's Installation ,Manual
WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER
1
2
4
3
1
2
1
2
3
4
F8254&F8254SN110V
Installation & Operating Instructions for the
Parrotuncle Owner's Installation ,Manual
WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER
F8254&F8254SN110V
Finish
WHITE
ANT
INPUT
OUTPUT
RED or BLACK
RECEIVER
CANOPY
WIRE NUT
Insert the corresponding port
of the fan cable into the remote
control .
Use wire connecting nuts supplied with the fan
FROM POWER SOURCE
AC 110- 120 VOLT 60Hz
3.5AMPS.
Remote controller
GENERAL INFORMATION
INSTRUCTION OF INSTALLATIONAND OPERATION
1.SETTING THE CODES
To set the codes, perform the following steps:
A.Setting the codes on the transmitter:
a.Remove battery cover.Press firmly on the arrow and slide battery cover off.
b.Slide code switches to your choice of up or down position.(Factory setting is all up. Do not use this position.Use a
Small screwdriver or ball point pen to slide firmly up or down (Figure 1)).
B.Setting the codes on the receiver:
The Learn Key must be pressed with in 30 seconds, after pressing the Power button.
If not, please press the Power button to restart.
Keep pressing the button learn key in excess of 3 second it becomes a LEARN status.
The receiver can remember the last codes status. The light flash two times.
2.INSTALLING RECEIVER IN CEILING FAN
A.Safety precautions:
WARNING: HIGH VOLTAGE! Disconnect power by
removing fuse or switching off circuit breaker.
Do not use with solid state fans.
Electrical wire must meet all local and national
electrical code requirements.
Supply for fan must be 110/120 volt, 60Hz. Maximum
fan motor amps: 1.0,Maximum light watts: 180
incandescent or ballast and LED.
Otherwise power can cause serious injury or death.
B.lnstalling receiver in fan:
a.Remove power from the circuit.
b.Remove ceiling fan canopy from the mounting
bracket.
c.Disconnect existing wiring between ceiling fan and
Supply in electrical junction box.
d. Make connections as follows, using the wire nuts
supplied:
This remote controller is desianed to separatelv control vour ceilina fan speed and light on and off.
There are four buttons(HI,MED, LoW,OFF) to control the speed of the fan and off.
The light button will control the light on and off.
The red indicator on the transmitter will light when one of the five buttons is pressed.
Installation & Operating Instructions for the
Parrotuncle Owner's Installation ,Manual
WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER
F8254&F8254SN110V
OP ERATING TRANSMITTER:
A.Install CR2025 volt battery.
(To prevent d amage to transmitter, r emove the battery if not used for a long time).
C. Operating the buttons on the panel of the transmitter.
ting the codes on the rec eiver:
1. Code matching key: The operation is as follows: press this key to code matching within 5 seconds
after the fan lamp is powered on. If the code matching is successful, the fan will make a "drop"
sound; if not, repeat the action.
Fan speed 3
STOP
I
Fan speed 2
Fan speed 1
Fan stop
on/off
Light on/off
2.Code matching key
Foward/Reve rse
1.
B.Store the transm itter away from excessive heat or humidity.
Installation & Operating Instructions for the
Parrotuncle Owner's Installation ,Manual
WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER
size of product
F8254&F8254SN110V
φ［12 .2"］
φ［12.2"］
［6 .1"］
φ［9 .44"］
Installation & Operating Instructions for the
Parrotuncle Owner's Installation ,Manual
WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER
Table of Contents
1.
Fan
/ Remote is not working
2.
Fan is noisy
3.
Fan Wobbles
4.
Light is not working
Please refer to the instruction sheet for detailed directions and descriptions of
installation steps
and requirements.
1.
FAN
/ REMOTE IS NOT WORKING
Ensure the remote is within the 20
foot range of the receiver
To reset the remote control: 1) Turn off power to fan
using the wall switch or circuit breaker. 2) Remove ba eries from remote.
3) Wait 10 seconds. 4) Replace ba eries and turn power on
Check ba eries to
insure they are good and oriented correctly
Check to make sure the frequency switches (DIP Switches) from the remote to the receiver are set to the same frequency
Check the main
and branch circuit fuses or breakers
If using a Variable Speed Wall Switch, ensure
it is specifically designed for use with a ceiling fan.
Check the line wire connec ns to the fan and the
switch wire conn e switch housing
per the instru ns
Support@parrotuncle.com
2.
THE FAN IS NOISY
Make sure all motor housing screws are tened
Make sure the screws that a an blade to motor ar t
Make sure the wire nut connectors are not ra against each other or the interior wall of the switch housing
Allow 24-hour break in period. Most noises associated with the new fan may disappear during th me
If using a ceiling light kit, make sure the glassware is secur htly
Make sure there is a short distance/gap from the ceiling to the top of the canopy. The canopy
should not touch the ceiling!
Make sure your ceiling box is secure and that the rubber isolator pads are used between the moun acket and outlet box
TROUBLESHOOTING GUIDE
F8254&F8254SN110V
Installation & Operating Instructions for the
Parrotuncle Owner's Installation ,Manual
WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER
3. THE FAN WOBBLES
Verify all blades and blade bracket screws are secure (most fan wobble problems are caused by loose parts). Once fan is properly
installed, run the ceiling fan for 10 minutes to let the fan self-adjust.
If wobble occurs a er running the fan for 10 minutes, verify blade level using the following process:
a)
select a point on the ceiling above the p of one of the blades. Then select the fan blade and measure from the center
of the selected blade to point on the ceiling. Rotate the fan un e next blade is oned and repeat the
measurement using the same point from the ceiling for every blade. Measurements
should be within 1/8 inch.
Customer Service Support@parr
otuncle.com to order a complimentary Blade Balancing Kit
Customer Service Support@parrotuncle
.com to order a complimentary Blade Balancing Kit
4.
LIGHT IS NOT WORKING
Check Bulb to make sure it is installed correctly
Remove non-working bulb and replace with a bulb that is known to be a good working bulb
To reset the remote control: 1) Turn off power to fan using the wall switch or circuit breaker. 2) Remove ba eries from
remote. 3) Wait 10 seconds. 4) Replace ba and turn power on
F8254&F8254SN110V
AFTER INSTALLATION
The fan blades have been adjusted in the factory to minimize any wobble
NOTE:CEILING FANS TEND TO MOVE DURING OPERATION DUE TO THE FACT THAT THEY
ARE MOUNTED ON A RUBBER CROMMET. IF THE FAN WAS MOUNTED RIGIDLY TO THE
CEILING, IT WOULD CAUSE EXCESS VIBRATION. MOVEMENT OF A FEW CENTIMENTERS
IS QUITE ACCEPTABLE AND DOES NOT SUGGEST ANY PROBLEM
WOBBLE”
TO REDUCE THE FAN WOBBLE: PLEASE CHECK THAT ALL SCREWS WHICH SECURED THE MOUNTING
BRACKET AND DOWNROD ARE SECURE.
BALANCING A WOBBLING CEILING FAN:
For your convenience, a Balancing Kit is included; please follow this procedure when balancing the fan:
1.Check that all blade and blade arm screws are secure.
2.Most fan wobbling problems are caused when blade levels are unequal. Check this level by
selecting a point on the ceiling above the tip of one of the
blades. Measure this distance.Rotate the fan until the next blade is positioned for
measurement. Repeat for each blade. The distance deviation should be equal within
1/8"(0.32cm).
3.Use the enclosed Blade Balancing Kit if the blade
wobble is still noticeable.
4.If the blade wobble is still noticeable, interchanging two
adjacent (side by side) blades can redistribute the weight and possibly result in smoother
operation. WARNING: TO REDUCE THE RISK OF PERSONAL INJURY, DO NOT BEND THE
BLADE ARM WHILE INSTALLING, BALANCING THE BLADES, OR CLEANING THE FAN. DO
NOT INSERT FOREIGN OBJECTS BETWEEN ROTATING FAN BLADES.
NOISE
When it is quiet(especially at night) you may hear occasional small noises. This is normal. Please allow
a 24-hour “breaking-in” period, most noises associated with a new fan disappear during the time.
CARE AND CLEANING
1.Periodic cleaning of your ceiling fan is the only maintenance required. Use a soft brush or lint free cloth to
avoid scratching the paint finish. Please make sure to turn off electricity power before you clean your fan
2.Do not use water when cleaning your ceiling fan. It could damage the motor or the blades
and create the possibility of an electrical shock.
3.Motor has permanently lubricated ball bearing. No need to oil
NOTE: MAKE SURE THE POWER IS OFF AT THE ELECTRICAL PANEL BOX BEFORE YOU
ATTEMPT ANY CLEANING OR REPAIRS.
Installation & Operating Instructions for the
Parrotuncle Owner's Installation ,Manual
WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER
F8254&F8254SN110V
/
