2. Century
  3. AL2211R5

Century AL2211R5 User manual

  • Hello! I am an AI chatbot trained to assist you with the Century AL2211R5 User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
MODELS/MODELOS: AL2211R5 | AL2511R5 | WL2211L
FTAL2211 | ALE2211 | ALE2511 | ALE3011
(In a kit inside the ladder)
(In a kit inside the ladder)
(mounted in aluminum feet)
WL2211L 22 1/2” X 54” 7’9”-10’3” *65” 74”
AL2211R5 22 1/2” X 54” 7’8”-10’3” *66” 74”
AL2511R5 25 1/2” X 54” 7’8”-10’3” *66” 74”
FTAL2211 22 1/2” X 54” 7’8”-10’3” *67” 74”
ALE2211 22 1/2” X 54” 7’7”-10’2” *68” 74”
ALE3011 30” X 54” 7’7”-10’2” *68” 74”
ALE2511 25 1/2” X 54” 7’7”-10’2” *68” 74”
ALUMINUM MODELS ONLY:
A. Using a tape measu re double check the heig ht of the ceiling.
B. Determine the locaon to cut the leadder rail and ladder feet for your ceiling height.
Follow table 3 and Figu re 13.
C. Cut the side rails and ladder feet (when required) at the appropriate line.
NOTE: The rail is not pre—ma rked for angle cut s.
D. Press down on the climbing se con to ensure that the folding a rms are fully
extended.


If the ac ladder looks like Figu re 17, then both of the legs a re too long and need to
be trimmend fu rther.
If the ac ladder looks like Figu re 15, then both of the legs a re too short, and the ac
ladder is not safe to use. A new Iower secon would need to be purchased from the
manufacturer.
F. Install weather stripping per instru cons p rovided.
G. To install trim molding Ie ave 3/8" clearance between your door panel at the hinged
end and 1/8" on other 3 sides.
Check the length a fter making your cuts
E. Slide aluminum foot over ladder rail as shown in
Figu re 14. Posion so the rubber foot is in contact
holes in rail. Aach using (2) 1/4" bolts and se rrated
nuts per side (included).
Again, be su re the ac ladder p ower arms are fully extended. Trimmed correctly,
your ac ladder should look like Figu re 16. Verify that there are no gaps in the se con
(AL2211R5, AL2511R5, WL2211L models)
WL2211L 22 1/2” X 54” 7’9”-10’3” *65” 74”
AL2211R5 22 1/2” X 54” 7’8”-10’3” *66” 74”
AL2511R5 25 1/2” X 54” 7’8”-10’3” *66” 74”
FTAL2211 22 1/2” X 54” 7’8”-10’3” *67” 74”
ALE2211 22 1/2” X 54” 7’7”-10’2” *68” 74”
ALE2511 25 1/2” X 54” 7’7”-10’2” *68” 74”
ALE3011 30” X 54” 7’7”-10’2” *68” 74”
(En un kit dentro de la escalera)
(Montada en las bases de aluminio)
WL2211L 22 1/2” X 54” 7’9”-10’3” *65” 74”
AL2211R5 22 1/2” X 54” 7’8”-10’3” *66” 74”
AL2511R5 25 1/2” X 54” 7’8”-10’3” *66” 74”
ALE2211
22 1/2” X 54” 7’8”-10’3” *67” 74”
MODELO APERTURA
APROXIMADA
“A” RANGO DE
ALTURA DE TECHO
“B” DISTANCIA
DE APERTURA
“C” ESPACIO
PARA DESPLIEGUE
FTAL2211
ALE2511
22 1/2” X 54”
25 1/2” X 54”
7’7”-10’2”
7’7”-10’2”
*68”
*68”
74”
74”
ALE3011 30” X 54” 7’7”-10’2” *68” 74”
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/