2. Blusafe
  3. Contour

Blusafe Contour Installation guide

  • Hello! I've reviewed the Blusafe Contour / Contour V Installation Manual and I'm ready to assist with your questions about installation process. This manual provides instructions on latch installation, drilling the required holes, adjusting handles direction, and connecting internal and external panels together.
  • What is the recommended height for drilling the main hole?
    What is the door thickness compatibility for the Contour lock?
    What is the length of screws to use for door with thickness 35-45mm?
    How many batteries are needed?
1P
Blusafe Contour / Contour V
Installation Manual v1.1
Please scan the QR to get the newest
manuals on Blusafe Products
2
P
0. Tools Required
1. Package Contents
2. Latch Installation Guide
3. Blusafe Contour Smart Lock
4. Determine Handle Direction
5. Change External Handle Direction
6. Change Internal Handle Direction
7. Installation of Blusafe Contour Smart Lock
P0
P1
P2
P4
P5
P6
P7
P8
Contents
Tools Required
Pliers
Pencil
Hammer
Drill Bits
Chisel
Drill
Measuring Tape
Screwdriver
1P
Internal Panel
Strike Plate
A - ST 3.9 x 20mm Self
-tapping Screw x 4
C - Screw Pillar
x 1
F- Key
x 3
Mounting Plate
Strike Box
B1- M4 x 35mm
Screw x 4
D - ST 3.9 x 16mm Self
-tapping Screw x 1
G - Keycard
x 2
External Panel
Latch
B2- M4 x 50mm
Screw x 4
E- Screwdriver
x 1
H- M4 x 10mm
Screw x 4
Package Contents
1. Package Contents P1
2
P
35mm to 54mm
1-2/5” to 2-1/8”
1"
26mm
2-5/16"
58mm
1"
Φ25mm
2-3/8"or 2-3/4"
60 or 70 mm
121mm
4-3/4"
2/5"
Φ10mm
2-1/8"
Φ54mm
It is suggested to drill both holes in door in
order to have a better installation of the lock.
If you choose not to drill the 2/5" (Φ10mm)
hole, the C Screw Pillar will not be used in the
"Installation of Contour Smart Lock".
Note
①TheContourhandleissuitabletouse
ondoorthicknessbetween1-2/5"and
2-1/8"(35and54mm).
Thefollowinglatchinstallationguideisdesignedfornewdoorsthatdonotalready
haveholesforthelockorlatch.Ifyourdooralreadyhastherequiredholestoinstall
thelatchandlock,youmayskipthestepsbelowandcontinuetoP04.
②Usethetemplateguidetomarktheholes
indooratrequiredheights(suggested
heightforΦ54mmholecentrelineis
38"or970mmfromthebaseofdoor).
Drillouta2-1/8"(Φ54mm)anda2/5"
(Φ10mm)hole.
③Foldthetemplateguidealongtheedge
ofthedoorandsplaceitoverthe2 ⅛ "
(54mm)diameterhole.Markthe1"
(25mm)diameterholeintheedgeof
thedoorforthelatch.Drilloutthe1"
(25mm)diameterlatchhole.Chiselout
theremainderoftheslotontheedgeof
thedoortoacceptthelatchbody.This
isarectangle1"x2¼"(26mmx58mm)
asshownabove.Thedepthmustbe⅛ "
(3mm)toacceptthelatchbody.Please
testthetofthelatchbodytoensurea
goodtbeforeinstalling.
Drill Lockset and Latch Holes
10.6070.5525
Latch Installation Guide
2. Latch Installation Guide P2 - P3
3P
15/16"(24mm)
1-1/8"(29mm)
1-1/8"(29mm)
2-3/4"(71mm)
1-3/8"(36mm)
Strike Plate
Strike Box
2-3/8" (60mm)
2-3/4" (70mm)
35mm to 54mm
1-2/5” to 2-1/8”
1"
26mm
2-5/16"
58mm
1"
Φ25mm
2-3/8"or 2-3/4"
60 or 70 mm
121mm
4-3/4"
2/5"
Φ10mm
2-1/8"
Φ54mm
Adjustthelengthofthelatchaccordingtobackset(2-3/8"(60mm)or2-3/4"
(70mm)).Fixtwoself-tappingscrewstothelatchplate.
①Withthelatchinstalled,extend
itandgentlycloseitagainstthe
doorframe.Markontheframe
thetopandbottomofthelatch.
②Markacentrelineonthejamb
forthestrikeplate.Ensurethis
centrelineallowsthedoorenough
spacetocloseagainstthestop.
③Placethestrikeplateonthejamb
aligningthemarksfromthelatch
tothebolthole.Alsoensurethe
strikeplateiscentredonthe
markedcenterline.Scribearound
theouteredgeofthestrikeplate
withapencilandchiselwithin
thescribedareatoadepthof
1/12"(2mm).
④Placethestrikeplateinthe
recessedholeandmarkthehole
forthelatch.
⑤Chiseltheholeouttoadepthof
1"(25mm)toallowthelatchto
extendandmovefreely.
⑥Insertthestrikeboxandstrike
plateintothehole.Screwinthe
strikeplateasshown.
Latch Installation Guide
Install the Latch
Install Strike Plate and Box
2. Latch Installation Guide P2 - P3
Screwdriver A × 2
A × 2
4
P
Blusafe Contour Smart Lock
3. Blusafe Contour Smart Lock P4
Battery Cover
Internal Handle
Louderspeaker Hole
Internal Panel
External Panel
Camera
（Only available in
Contour V）
Micro USB
Cylinder Cover
Key Card Area
Keypad
Fingerprint
Sensor
Mechanical
Key Hole
External
Handle
5P
Determine Handle Direction
Dependingonwhichwayyourdooropens,determinewhichwaythehandlesneed
toface.
Thehandlesshouldalwayspointtowardsthedoorhinges.ChecktheContour/
ContourVhandlesagainstthecurrenthandles.
Ifthehandlesneedtofacetheotherway,pleaseseenextpage.
4. Determine Handle Direction P5
6
P
4. Rotate the spindle
down 45 degrees until the
screw hole is visible.
Locate and fasten the set
screw.
3. Rotate the handle
down from its
horizontal position,
225 degrees.
1. Rotate the handle
and the spindle by 45
degrees to expose the
set screw.
2. Unwind the set screw.
screw hole
Change External Handle Direction
Screwdriver
5. Change External Handle Direction P6
7P
2. Rotate the handle
down 180 degrees.
1. Unwind the set screw.
3. Locate and fasten
the set screw.
4. Rotate the spindle
down 45 degrees until the
screw hole is visible.
Locate and fasten the set
screw.
3. Rotate the handle
down from its
horizontal position,
225 degrees.
1. Rotate the handle
and the spindle by 45
degrees to expose the
set screw.
2. Unwind the set screw.
screw hole
Change Internal Handle Direction
Screwdriver
6. Change Internal Handle Direction P7
8
P
Pleasemakesurethelatchisinstalledproperlyasperthe"LatchInstallationGuide"
priortothefollowinginstallationsteps:
①Measurethethicknessofthedoor.
②Pleaseselecttheappropriatescrewsbasedonthedoorthickness.Youcanrefer
totheabovetableforreference.
Installation of Blusafe Contour Smart Lock
Select the appropriate
length xing screw
according to the
thickness of the door.
Boor Thickness/mm Screw B Length
1 - ²/₅" t o 1 - ⁴/₅ " (35-45mm) M4×35mm
M4×50mm1 - ⁴/₅ " t o 2 - ¹/₈ " (45-54mm)
Measuring tape
7. Installation of Blusafe Contour Smart Lock P8 - P16
9P
③TightentheCScrewPillaronthebackoftheexternalpanel.
④Passtheexternalpanelcablethroughthebottomofthehole.Insertthespindle
throughthespindleholeofthelatch.Carefullypushtheouterpaneltowardsthe
door,andmakesuretheCScrewPillarfeedthroughtheupperholeofthedoor.
Please use the 3M tape at the back of external panel to reinforce the mounting.
Tip
Installation of Blusafe Contour Smart Lock
Please peel o the skin and
use the 3M tape at the back
of external panel to reinforce
the mounting.
The C Screw Pillar must
be used if the smart lock is
exposed to rain, to ensure the
best installation and weather
seal.
Make sure the cable
goes through the
bottom of hole.
Tip
Warning!
Pliers C × 1
7. Installation of Blusafe Contour Smart Lock P8 - P16
10
P
⑤Pullthecablethroughtheslotofthemountingplate.
Installation of Blusafe Contour Smart Lock
Make sure the cable
is pulled through the
bottom of hole.
7. Installation of Blusafe Contour Smart Lock P8 - P16
11P
⑥Insertthescrews,butDONOTfullytightenthem.Adjusttheexternalpanelto
thecorrectpositionandthenproceedtotightenthescrews.
Installation of Blusafe Contour Smart Lock
B × 3 D × 1
B × 1
or
＋
Alternative
If you used the 3M glue only
and not the C Screw Pillar on
the external, please use the
ST3.9x16mm self-tapping
screw D instead of the B Screw
at the top.
B Screw × 3
B Screw or
D Screw
7. Installation of Blusafe Contour Smart Lock P8 - P16
Screwdriver
12
P
Installation of Blusafe Contour Smart Lock
⑦Unwindthebattery
coverscrewwiththeE
Screwdriverprovided,
removethebatterycover.
E × 1
7. Installation of Blusafe Contour Smart Lock P8 - P16
13P
Installation of Blusafe Contour Smart Lock
The cable MUST be
pulled through this slot.
⑧Connecttheexternalandinternalcablestogether.
7. Installation of Blusafe Contour Smart Lock P8 - P16
Please make sure the cables are connected in the correct orientation otherwise will cause
permanent damage to the lock!
Warning!
Red
White
Red
Red
14
P
Installation of Blusafe Contour Smart Lock
⑨Buckletheinternalplateontothemountingplate.FixtheHScrewswitha
screwdriver.
H × 4Screwdriver
7. Installation of Blusafe Contour Smart Lock P8 - P16
15P
Installation of Blusafe Contour Smart Lock
⑩Rotatethehandletoensurethelatchcanbeextendedandretractedfreely.
Standinside,closethedoorandrepeattherotationofthehandle.Ensurethe
latchcanstillbeextendedandretractedfreely.Ifnot,youmayneedtoadjust
thepositioningofthelatchonthedoor.
⑪Openthebatterycassette.Insert8AAbatteriesasshownabove.
Ensure the batteries
are inserted correctly.
For the best possible experience, please use high quality AA batteries in your Smart Lock.
The batteries will last 6-8 months depending on usage and environment; however, we
recommend that you change the batteries every six months or when notied in your App.
Note
7. Installation of Blusafe Contour Smart Lock P8 - P16
16
P
Installation of Blusafe Contour Smart Lock
⑫Putonthebatterycover,xthescrewwiththeEScrewdriver.
E × 1
7. Installation of Blusafe Contour Smart Lock P8 - P16
17P
Securityatyourngertips——Blusafe
18
P
Please scan the QR to get the newest
manuals on Blusafe Products
/