Aeg-Electrolux EA130 User manual

Page is loading ...

g

11

g

Dear Customer,

Please read this instruction manual

carefully. Please pay particular atten-

tion to the safety instructions. Retain it

for future reference.

Give the instruction manual to any

future owner of the machine.

Equipment (Figure 1)

A On/off switch

B Power indicator light

C Temperature indicator light

D Water tank (at the rear)

E Selector dial for coffee or steam

F Steam nozzle (with attachment)

G Measuring spoon

H Maintenance tool

J Ground coffee presser

K 1-cup filter

L 2-cup filter

M Filter for prepacked portions

(only EA130)

N Filter holder

O Finger protector

P Drip catcher

Q Drip grating

R Fill level indicator

S Brew head with filter holder retainer

T Filter in brew head (inside)

U Rating plate

1 Safety instructions

Safety when setting up the

appliance

• The appliance must be stable when

standing. Check that the site at which

the appliance is to be installed is even

and level.

• The appliance may only be connected

to a mains supply which has a voltage,

electricity type and frequency that

complies with the specifications on the

rating plate (see underside of the

appliance).

Safety when operating the

appliance

• Never bring the electrical cord in

contact with hot components of the

appliance.

• Never remove the power plug from the

power point by pulling on the cord.

• Do not use the appliance if:

– the cord is damaged or

– there is visible damage to the

housing.

• The steam nozzle, filter, filter holder

and retainer necessarily become hot

during use.

• Ensure that children are kept away.

• The housing will necessarily become

warm during use.

• Do not remove the filter holder during

the brewing process as the appliance is

pressurised. The risk of burns exists.

• Fill the water tank only with cold

water, never with distilled water,

mineral water, milk or other liquids.

• Do not use the appliance if the water

tank has not been filled.

• Do not use the appliance without the

drip tray or the drip grating.

Safety during cleaning

• Prior to maintenance or cleaning

ensure that the appliance has been

switched off and that the power plug

has been disconnected.

822_949_282 EA120.book Seite 11 Montag, 2. April 2007 7:25 19

g

12

• Follow the instructions referring to

decalcification.

• Do not immerse the appliance in water.

Safety during repairs

Repairs to electrical appliances may

only be carried out by qualified service

engineers. Improper repairs can give

rise to significant hazards for the user.

If the supply cord is damaged, it must

be replaced by the manufacturer, its

service agent or similarly qualified per-

sons in order to avoid a hazard.

If the appliance is used for purposes

other than those for what it was

intended or is operated wrongly, no lia-

bility for possible damages can be

accepted.

;

This appliance conforms with the fol-

lowing EC Directives:

• Low Voltage Directive 2006/95/EC

• EMC Directive 89/336/EEC with

amendments 92/31/EEC and

93/68/EEC

Prior to using the appliance for

the first time

Please read the safety instructions in

order to prevent danger to yourself

and damage to the appliance.

0 Insert the power plug into the power

outlet.

Prior to preparing an espresso for the

first time you should rinse out the

heating system once by filling the tank.

Proceed exactly as described in the

section “Making an espresso” and

“Frothing milk”, but without placing

any ground coffee in the filter. Place a

container that is as large as possible in

the middle of the drip grating

(figure 1/Q) and under the steam noz-

zle (figure 1/F).

Making an espresso

After having been brewed, the espresso

should be covered with a dense frothy

layer, the so-called crema.

To achieve an aromatic espresso with

crema, fresh, clear water, the correct

size grounds and the water tempera-

ture are important.

1. Adding water (Figure 2)

0 Pull the water tank upwards and out of

the appliance (figure 2).

0 Open the tank lid.

0 Fill the water tank with cold, clear

water only.

Ensure that the water line does not lie

below the MIN (minimum) line or

above the MAX (maximum) line.

0 Close the tank lid.

0 Replace the water tank and press it

downwards so that it is sitting firmly in

the appliance.

3

You can also lift the tank lid and fold it

to the side. This enables you to fill the

water tank directly when it is in the

appliance, e.g. with a jug.

2. Switching on the appliance

0 Switch the appliance on using the on/

off switch (figure 1/A). The power indi-

cator (figure 1/B, red) will illuminate

and the temperature indicator

(figure 1/C, green) will start to blink.

As soon as the operating temperature

has been attained, the temperature

indicator light will be on. The tempera-

ture indicator may blink again while

the appliance is being used to indicate

that the appliance is re-heating.

822_949_282 EA120.book Seite 12 Montag, 2. April 2007 7:25 19

g

13

3. Adding espresso grounds

(figures 3, 4)

0 Take the filter holder, fold back the fin-

ger protector and place the 1-cup filter

or the 2-cup filter into the filter holder

(figure 3).

3

Only EA 130: When using prepacked

portions, insert the filter for prepacked

portions (figure 1/M and figure 5).

0 Fill the filter with espresso grounds.

Use:

1 full measuring spoon for the 1-cup

filter, 2 full measuring spoons for the

2-cup filter.

0 Lightly press the espresso grounds into

the filter (figure 4) using the ground

coffee presser (figure 1/J). Ensure that

after pressing the coffee, the filter is

still filled to the rim with espresso

grounds. Clean any espresso grounds

away from the rim of the filter.

3

Do not press the espresso grounds too

firmly into the filter. In such an event

the flow of water through the coffee

can decrease significantly. (See also

“What to do if…”)

3

If you grind espresso grounds yourself,

choose the “middle” fineness level.

4. Screwing on the filter holder

(Figures 6, 7)

0 Position the filter holder in the filter

retainer such that the handle of the

filter holder is located below the left

white triangle (figure 6,“1“).

0 Twist the filter holder to the right as

far as it will go (figure 6,“2“), so that

the handle is pointing forwards and is

located beneath the white line

between the two points (figure 7,“3“).

5. Placing cup(s) underneath

(Figure 8)

0 Place one or two cups under the open-

ings in the filter holder (figure 8).

6. Brewing an espresso

3

The appliance must have attained its

operating temperature (green light

figure 1/C is on).

0 Turn the selector dial (figure 1/E) to

the symbol . The water will now be

forced through the espresso grounds

under high pressure.

3

Prior to the actual brewing process, the

ground coffee is moistened to extract

its full aroma. The brewing process is

then continued.

0 When the desired amount of espresso

has been brewed, turn the selector dial

left again to the “•” position.

3

Each time after making an espresso or

after using steam when the selector

dial is turned to the “•” position, any

remaining water is directed to the drip

tray. Each additional cup is brewed

using fresh water. This is how to obtain

the total enjoyment out of espresso.

This is why the drip tray must be emp-

tied regularly.

7. Removing the filter holder

(Figure 9)

0 Twist the filter holder to the left and

out of the retainer.

0 Fold the finger protector forwards and

hold it down. Tap the used espresso

grounds out of the filter holder and

out of the filter (figure 9).

0 Rinse the filter holder and the filter

with warm water. Do not clean the fil-

ter holder in the dishwasher!

3

If the appliance is not going to be used

for a longer period of time, do not

screw the filter holder back in. This will

increase the life of the seal located on

the brew head.

822_949_282 EA120.book Seite 13 Montag, 2. April 2007 7:25 19

g

14

Creating steam/frothing milk

(Figures 10, 11)

The hot steam can be used to froth

milk for a cappuccino or to heat liq-

uids.

1. Switch on the appliance

0 Place the attachment provided onto

the steam nozzle (figure 10).

0 Switch on the appliance using the on/

off switch (figure 1/A). Wait until the

appliance has attained its operating

temperature and the green tempera-

ture indicator (figure 1/C) is on.

2. Creating steam/frothing milk

0 Pour some milk or other liquid to be

heated into a heat-proof container.

0 Immerse the steam nozzle into the milk

or liquid to be heated (figure 11).

0 Turn the selector dial (figure 1/E) to

the left onto the symbol. The green

temperature indicator (figure 1/C) is

blinking and the appliance will begin

to create steam. At the beginning some

drops of water may drip out of the

nozzle as well.

Important: So as not to prevent the

steam from exiting, the steam nozzle

must not touch the base of the con-

tainer.

0 Stop steam from being emitted by

turning the selector dial (figure 1/E)

back to the right into the “•” position.

0 Place the steamed liquid to one side

and turn the steam selection switch

back to the symbol for a couple of

seconds. This will remove any milk resi-

due or residue from other liquids out

of the nozzle. Caution: The steam is

hot.

3

To achieve a fine, creamy milk froth it

is best to use cool low-fat milk.

Making a cappuccino

Fill a large coffee cup from ½ to ¾ full

of espresso. Pour the frothed milk over

the top. Sprinkle a little cocoa over the

milk froth.

Cleaning and care

Daily care

We recommend that, each day prior to

the first and after the last espresso, you

rinse out the system for approx. 10

seconds without espresso grounds in

order to prevent particles coffee from

becoming lodged in the appliance. Pro-

ceed as for making an espresso, but

without using espresso grounds.

0 Afterwards, turn the selector dial (fig-

ure 1/E) briefly to the position.

0 Pour any remaining water out of the

water tank.

Cleaning (figures 12 – 16)

1

Prior to cleaning the appliance, switch

it off and disconnect the power plug.

Do not clean any part of the appli-

ance in the dishwasher.

0 Wipe all the appliance’s surfaces using

a damp cloth. Do not use harsh or

scratching cleaning agent.

0 Rinse out the water tank at least once

a week in normal rinse water.

0 Clean the 1-cup filter and the 2-cup

filter from time to time using a brush.

Steam nozzle

0 Remove the attachment from the

steam nozzle and rinse the attachment

in normal rinse water.

0 Wipe the steam nozzle clean using a

damp cloth. You can use the mainte-

nance tool (figure 1/H) to screw off

the nozzle head to clean it or decalcify

it.

Drip grating and drip tray

The drip tray must be emptied when

the level indicator (figure 1/R) is pro-

truding above the drip grating.

0 Insert your fingers into the holes in the

drip grating. Remove the drip grating

and rinse it under running water

(figure 12).

0 To empty it, hold the drip tray on both

sides and pull it forwards and out of

the appliance (figure 13).

822_949_282 EA120.book Seite 14 Montag, 2. April 2007 7:25 19

g

15

0 Remove the plastic attachment and

rinse both under running water

(figure 14).

0 Place the plastic attachment back into

the drip tray.

0 Push the clean drip tray back into the

appliance and place the drip grating

back in.

Cleaning the brew filter

From time to time check the brew filter

to ensure that the holes in the filter

have not become blocked by coffee

particles. The brew filter is located on

the underside of the brew head.

If the holes have become blocked:

0 Unscrew the brew filter using a coin

(figure 15).

0 Remove the brew filter and seal

(figure 16/1) and remove the brew fil-

ter’s seal (figure 16/2).

0 Clean the brew filter with warm water

and a brush.

0 Rinse the seal with warm rinse water.

3

If the appliance is to be transported at

temperatures below zero:

0 Empty the water tank.

0 Turn the selector dial (figure 1/E) to

the position and let the appliance

dry.

Decalcifying

If the espresso is flowing through the

filter at a slower rate than usual, it is

time for the appliance to be decalci-

fied.

We recommend that you decalcify the

machine once every three months. If

you live in an area with hard water the

decalcifying procedure may have to be

carried out more often.

3

We recommend to use only the original

AEG decalcifying tabs PNC

900 195 537/7.

Important: Prior to decalcifying, re-

move the brew filter (figure 1/T) and

the brew filter’s seal, as described in

the section “Cleaning the brew filter”

(figures 15, 16).

First pour the water into the water

tank, then add the decalcifier; never in

the reverse order. At least 0.5 litres of

water must be used. The decalcifier

should be added accordingly.

0 Remove the power plug from the

power point and allow the appliance to

cool.

0 Place the filter holder in position with-

out the filter.

0 Place a sufficiently large container

under the filter holder.

0 Insert the power plug into the power

point and switch on the appliance.

0 Afterwards, turn the selector dial (fig-

ure 1/E) to the position and let

approx. 1/3 of the decalcifier flow

through the system.

0 Then switch off the appliance and

allow the decalcifying solution to act

for approx. 10 minutes.

0 Allow the rest of the decalcifying solu-

tion to rinse the brew head.

0 Then thoroughly clean the water tank.

0 Fill the water tank with fresh water

and allow all of the water to flow over

the brew head.

Repeat the procedure if there is a lot of

limescale.

0 After decalcifying the appliance,

replace the brew filter and seal.

What to do if…

• the espresso temperature is too low:

– Carry out the brewing procedure

without using espresso grounds, but

using the filter and filter holder, in

order to preheat the system.

–Preheat the cups.

– Decalcify the appliance.

• the flow speed decreases noticeably:

– Do not press the espresso grounds

too firmly into the filter.

– Do not grind the espresso grounds

too finely (“medium” fineness).

– Decalcify the appliance.

822_949_282 EA120.book Seite 15 Montag, 2. April 2007 7:25 19

g

16

• the espresso is flowing out of the side

of the filter holder:

– Ensure that the filter holder has

been placed in the retainer correctly.

– Twist the filter holder a little more

firmly into the retainer.

– Clean any espresso grounds away

from the rim of the filter holder.

• no espresso is coming out:

– Ensure that the water tank has been

filled and is correctly in place.

– Ensure that the filter holder has

been placed in the retainer correctly.

– Ensure that the selector dial

(figure 1/E) has been turned right to

the position.

– Do not press the espresso grounds

too firmly into the filter.

– Clean the brew filter.

– Decalcify the appliance.

• the crema is no longer being produced

as it should:

– Ensure that there are enough

espresso grounds in the filter.

– Always use fresh espresso grounds.

– Press the espresso grounds lightly.

• too little milk froth is created when

steaming milk:

– Always use cool, fresh and low-fat

milk.

– Clean the steam nozzle.

• the flow increases:

– the espresso grounds have been

ground too rough:

– Ensure that there are enough

espresso grounds in the filter.

• the coffee machine switches itself off

while operating:

The appliance pump is equipped with a

temperature fuse that protects it from

overheating. The temperature fuse

interrupts the machine’s operation, if

the machine is operated for too long or

if the pump is run without water.

– Set the on / off switch to “off” and

remove the plug from the mains

socket.

– Leave the machine to cool for at

least 20 minutes. Fill up with water.

– Plug the appliance into the mains

again and switch it on. If the

appliance still does not work, please

contact our Customer Care

Department.

Technical data

• Mains voltage: 230–240 V, 50 Hz

• Power consumption: 1250 W

(See rating plate on the underside of

the appliance.)

Disposal

2

Packaging material

The packaging materials are environ-

mentally friendly and can be recycled.

The plastic components are identified

by markings, e.g. >PE<, >PS<, etc.

Please dispose of the packaging mate-

rials in the appropriate container at

the community waste disposal faci-

lities.

2

Old appliance

The symbol

W on the product or on

its packaging indicates that this pro-

duct may not be treated as household

waste. Instead it shall be handed over

to the applicable collection point for

the recycling of electrical and electro-

nic equipment. By ensuring this pro-

duct is disposed of correctly, you will

help prevent potential negative conse-

quences for the environment and

human health, which could otherwise

be caused by inappropriate waste

handling of this product. For more

detailed information about recycling

of this product, please contact your

local city office, your household waste

disposal service or the shop where you

purchased the product.

822_949_282 EA120.book Seite 16 Montag, 2. April 2007 7:25 19

Page is loading ...

Electrolux Hausgeräte Vertriebs GmbH

Muggenhofer Str. 135

D-90429 Nürnberg

http://www.electrolux.de

822 949 282 - 04 - 0407

822_949_282 EA120.book Seite 96 Montag, 2. April 2007 7:25 19

Aeg-Electrolux EA130 User manual

Aeg-Electrolux EA130 User manual

in other languages

Related papers

Other documents