Black & Decker KS602E T1 Owner's manual

Page is loading ...

5

ENGLISH

3. Personal safety

a. Stay alert, watch what you are doing and use common

sense when operating a power tool. Do not use a power

toolwhileyouaretiredorundertheinuenceofdrugs,

alcohol or medication. A moment of inattention while

operating power tools may result in serious personal injury.

b. Use personal protective equipment. Always wear eye

protection. Protective equipment such as dust mask,

non-skid safety shoes, hard hat, or hearing protection

used for appropriate conditions will reduce personal injuries.

c. Prevent unintentional starting. Ensure the switch is in

the off-position before connecting to power source

and/or battery pack, picking up or carrying the tool.

Carrying power tools with your nger on the switch or

energising power tools that have the switch on invites

accidents.

d. Remove any adjusting key or wrench before turning

the power tool on. A wrench or a key left attached to a

rotating part of the power tool may result in personal injury.

e. Do not overreach. Keep proper footing and balance at

all times. This enables better control of the power tool in

unexpected situations.

f. Dress properly. Do not wear loose clothing or jewellery.

Keep your hair, clothing and gloves away from moving

parts. Loose clothes, jewellery or long hair can be caught

in moving parts.

g. If devices are provided for the connection of dust

extraction and collection facilities, ensure these are

connected and properly used. Use of dust collection can

reduce dust-related hazards.

4. Power tool use and care

a. Do not force the power tool. Use the correct power

tool for your application. The correct power tool will do

the job better and safer at the rate for which it was designed.

b. Do not use the power tool if the switch does not turn it

on and off. Any power tool that cannot be controlled with

the switch is dangerous and must be repaired.

c. Disconnect the plug from the power source and/or the

battery pack from the power tool before making any

adjustments, changing accessories, or storing power

tools. Such preventive safety measures reduce the risk of

starting the power tool accidentally.

d. Store idle power tools out of the reach of children and

do not allow persons unfamiliar with the power tool or

these instructions to operate the power tool. Power

tools are dangerous in the hands of untrained users.

e. Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and any

other condition that may affect the power tools

operation. If damaged, have the power tool repaired

before use. Many accidents are caused by poorly

maintained power tools.

Intended use

Your Black & Decker jigsaw has been designed for sawing

wood, plastics and sheet metal. This tool is intended for

consumer use only.

Safety instructions

General power tool safety warnings

@

Warning! Read all safety warnings and all

instructions. Failure to follow the warnings and

instructions listed below may result in electric shock,

re and/or serious injury.

Save all warnings and instructions for future reference.

The term "power tool" in all of the warnings listed below refers

to your mains operated (corded) power tool or battery

operated (cordless) power tool.

1. Work area safety

a. Keep work area clean and well lit. Cluttered or dark

areas invite accidents.

b. Do not operate power tools in explosive atmospheres,

suchasinthepresenceofammableliquids,gases

or dust. Power tools create sparks which may ignite the

dust or fumes.

c. Keep children and bystanders away while operating

a power tool. Distractions can cause you to lose control.

2. Electrical safety

a. Power tool plugs must match the outlet. Never modify

the plug in any way. Do not use any adapter plugs

with earthed (grounded) power tools. Unmodied plugs

and matching outlets will reduce risk of electric shock.

b. Avoid body contact with earthed or grounded surfaces

such as pipes, radiators, ranges and refrigerators.

There is an increased risk of electric shock if your body is

earthed or grounded.

c. Do not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of electric

shock.

d. Do not abuse the cord. Never use the cord for carrying,

pulling or unplugging the power tool. Keep cord away

from heat, oil, sharp edges or moving parts. Damaged

or entangled cords increase the risk of electric shock.

e. When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of a cord

suitable for outdoor use reduces the risk of electric shock.

f. If operating a power tool in a damp location is

unavoidable, use a residual current device (RCD)

protected supply. Use of an RCD reduces the risk of

electric shock.

6

ENGLISH

f. Keep cutting tools sharp and clean. Properly maintained

cutting tools with sharp cutting edges are less likely to

bind and are easier to control.

g. Use the power tool, accessories and tool bits etc., in

accordance with these instructions, taking into

account the working conditions and the work to be

performed. Use of the power tool for operations different

from those intended could result in a hazardous situation.

5. Service

a. Haveyourpowertoolservicedbyaqualiedrepair

person using only identical replacement parts. This will

ensure that the safety of the power tool is maintained.

Additional power tool safety warnings

@

Warning! Additional safety warnings for jigsaws and

reciprocating saws

u Hold power tool by insulated gripping surfaces, when

performing an operation where the cutting accessory

may contact hidden wiring or its own cord. Cutting

accessory contacting a “live” wire may make exposed

metal parts of the power tool “live” and could give the

operator an electric shock.

u Use clamps or another practical way to secure and

support the workpiece to a stable platform. Holding the

work by hand or against your body leaves it unstable and

may lead to loss of control.

u Keep hands away from cutting area. Never reach

underneath the work piece for any reason. Do not insert

ngers or thumb into the vicinity of the reciprocating blade

and blade clamp. Do not stabilize the saw by gripping the

shoe.

u Keep blades sharp. Dull or damaged blades may cause

the saw to swerve or stall under pressure. Always use the

appropriate type of saw blade for the workpiece material

and type of cut.

u When cutting pipe or conduit, make sure that they are free

from water, electrical wiring, etc.

u Do not touch the workpiece or the blade immediately after

operating the tool. They can become very hot.

u Be aware of hidden hazards, before cutting into walls,

oors or ceilings, check for the location of wiring and pipes.

u The blade will continue to move after releasing the switch.

Always switch the tool off and wait for the saw blade to

come to a complete standstill before putting the tool down.

Warning! Contact with, or inhalation of dusts arising from

cutting applications may endanger the health of the operator

and possible bystanders. Wear a dust mask specically

designed for protection against dust and fumes and ensure

that persons within or entering the work area are also protected.

u This tool is not intended for use by persons (including

children) with reduced physical, sensory or mental

capabilities, or lack of experience and knowledge, unless

they have been given supervision or instruction

concerning use of the appliance by a person responsible

for their safety. Children should be supervised to ensure

that they do not play with the appliance.

u The intended use is described in this instruction manual.

The use of any accessory or attachment or performance

of any operation with this tool other than those

recommended in this instruction manual may present

a risk of personal injury and/or damage to property.

Safety of others

u This appliance is not intended for use by persons

(including children) with reduced physical, sensory or

mental capabilities, or lack of experience and knowledge,

unless they have been given supervision or instruction

concerning use of the appliance by a person responsible

for their safety.

u Children should be supervised to ensure that they do not

play with the appliance.

Residual risks.

Additional residual risks may arise when using the tool which

may not be included in the enclosed safety warnings. These

risks can arise from misuse, prolonged use etc.

Even with the application of the relevant safety regulations

and the implementation of safety devices, certain residual

risks can not be avoided. These include:

u Injuries caused by touching any rotating/moving

parts.

u Injuries caused when changing any parts, blades or

accessories.

u Injuries caused by prolonged use of a tool. When

using any tool for prolonged periods ensure you take

regular breaks.

u Impairment of hearing.

u Health hazards caused by breathing dust developed

when using your tool (example:- working with wood,

especially oak, beech and MDF.)

Vibration

The declared vibration emission values stated in the technical

data and the declaration of conformity have been measured in

accordance with a standard test method provided by

EN 60745 and may be used for comparing one tool with

another. The declared vibration emission value may also be

used in a preliminary assessment of exposure.

7

ENGLISH

Warning! The vibration emission value during actual use of

the power tool can differ from the declared value depending

on the ways in which the tool is used. The vibration level may

increase above the level stated.

When assessing vibration exposure to determine safety

measures required by 2002/44/EC to protect persons regularly

using power tools in employment, an estimation of vibration

exposure should consider, the actual conditions of use and the

way the tool is used, including taking account of all parts of the

operating cycle such as the times when the tool is switched off

and when it is running idle in addition to the trigger time.

Labels on tool

The following pictograms are shown on the tool:

:

Warning! To reduce the risk of injury, the user must

read the instruction manual.

Electrical safety

#

This tool is double insulated; therefore no earth wire

is required. Always check that the power supply

corresponds to the voltage on the rating plate.

u If the supply cord is damaged, it must be replaced by the

manufacturer or an authorised Black & Decker Service

Centre in order to avoid a hazard.

Features

This tool includes some or all of the following features:

1. On/off switch

2. Lock-on button

3. Dust extraction outlet

4. Shoe plate

5. Saw blade support roller

Fig. E

6. Saw blade storage compartment (KS602E & KS603E)

Assembly

Warning! Before attempting any of the following operations,

make sure that the tool is switched off and unplugged and that

the saw blade has stopped. Used saw blades may be hot.

Adjustingthesawbladesupportroller(g.A&B)

u Loosen the two screws (8).

u Push the blade support roller (5) forward until it touches

the back edge of the saw blade (7).

u Tighten the two screws (8).

Fittingandremovingthesawblade(g.C)

u Before tting or removing the saw blade (7) the saw blade

support roller (5) must be adjusted to the rear position so

that it does not contact the blade.

u Loosen (do not remove) the two screws (10).

u Hold the saw blade (7) with the teeth facing forward.

u Insert the shank of the saw blade (7) into the blade holder

(9) as far as it will go.

u Slightly tighten the two screws (10) alternately to position

the blade, then fully tighten the two screws (10).

u Adjust the saw blade support roller (5) as described above.

u To remove the saw blade (7), turn both screws (10) one

turn counter-clockwise.

Connectingavacuumcleanertothetool(g.D)

An adaptor (11) is required to connect a vacuum cleaner or

dust extractor to the tool. The adaptor can be purchased from

your local Black & Decker retailer.

u Push the adaptor (11) into the dust extraction outlet (3).

u Connect the vacuum cleaner hose (12) to the adaptor (11).

Sawbladestorage(KS602E&KS603Eonly)(g.E)

Saw blades (7) can be stored in the storage compartment (6)

located on the side of the tool

u Open the cover of the saw blade storage compartment (6)

by holding the tab on the top of the door and pulling outwards.

u Remove or store saw blades (7) in the storage

compartment (6).

u Close the cover of the saw blade storage compartment (6)

and make sure that it is latched closed.

Cutlineblower(g.F)

u To aid visibility when cutting, your jigsaw is equipped with

a cut line blower (13) which will keep the work area clear

of dust as you saw.

Use

Adjustingtheshoeplateforbevelcuts(g.G)

The shoe plate can be set to make either a straight cut or a

left or right bevel cut at an angle of 45°.

u Loosen the screws (8).

u Pull the shoe plate (4) forward, rotate the shoe plate (4) to

the left or right and push it back into the 45° location.

u Push the blade support roller (5) forward until it touches

the saw blade (7).

u Tighten the screws (8).

To reset the shoe plate for straight cuts:

u Loosen the screws (8).

u Pull the shoe plate (4) forward, rotate to the centre and

push it back into the 0° location.

u Push the blade support roller (5) forward until it touches

the saw blade (7).

8

ENGLISH

u Tighten the screws (8).

Variable speed control

The tool has a variable speed on/off switch (1). The operating

speed depends on how far you press the switch.

u Use a high speed for wood, medium speed for aluminium

and PVC and low speed for metals other than aluminium.

Switching on and off

u To switch the tool on, press the on/off switch (1).

u To switch the tool off, release the on/off switch (1).

u For continuous operation, press the lock-on button (2) and

release the on/off switch (1).

u To switch the tool off when in continuous operation, press

and release the on/off switch (1).

Hints for optimum use

u Hold the tool rmly with both hands while cutting.

u The shoe should be held rmly against the material being

cut. This will help prevent the saw from jumping, reduce

vibration and minimise blade breakage.

u Let the blade run freely for a few seconds before starting

the cut.

u Apply only a gentle pressure to the tool while performing

the cut.

Sawing laminates

When cutting laminates splintering may occur which can

damage the presentation surface. The most common saw

blades cut on the upward stroke, therefore if the shoe plate is

sitting on the presentation surface either use a saw blade that

cuts on the downward stroke or:

u Use a ne-tooth saw blade.

u Saw from the back surface of the workpiece.

u Clamp a piece of scrap wood or hardboard to both sides

of the workpiece to minimise splintering, and saw through

this sandwich.

Sawing metal

u Be aware that sawing metal takes much more time than

sawing wood.

u Use a saw blade suitable for sawing metal.

u When cutting thin sheet metal, clamp a piece of scrap

wood to the back surface of the workpiece and cut through

this sandwich.

u Spread a lm of oil along the intended line of cut.

Maintenance

Your Black & Decker tool has been designed to operate over a

long period of time with a minimum of maintenance.

Continuous satisfactory operation depends upon proper care

and regular cleaning.

Warning! Before performing any maintenance or cleaning,

make sure that the tool is switched off and unplugged and that

the saw blade has stopped.

u Regularly clean the ventilation slots in your tool and

charger using a soft brush or dry cloth.

u Regularly clean the motor housing using a damp cloth.

Do not use any abrasive or solvent-based cleaner.

Never let any liquid get inside the tool and never immerse

any part of the tool into liquid.

Mainsplugreplacement(U.K.&Irelandonly)

If a new mains plug needs to be tted:

u Safely dispose of the old plug.

u Connect the brown lead to the live terminal in the new plug.

u Connect the blue lead to the neutral terminal.

Warning! No connection is to be made to the earth terminal.

Follow the tting instructions supplied with good quality plugs.

Recommended fuse: 5 A.

Protecting the environment

Z

Separate collection. This product must not be

disposed of with normal household waste.

Should you nd one day that your Black & Decker product

needs replacement, or if it is of no further use to you, do not

dispose of it with household waste. Make this product

available for separate collection.

z

Separate collection of used products and packaging

allows materials to be recycled and used again.

Re-use of recycled materials helps prevent

environmental pollution and reduces the demand for

raw materials.

Local regulations may provide for separate collection of

electrical products from the household, at municipal waste

sites or by the retailer when you purchase a new product.

Black & Decker provides a facility for the collection and

recycling of Black & Decker products once they have reached

the end of their working life. To take advantage of this service

please return your product to any authorised repair agent who

will collect them on our behalf.

You can check the location of your nearest authorised repair

agent by contacting your local Black & Decker ofce at the

address indicated in this manual. Alternatively, a list of

authorised Black & Decker repair agents and full details of our

after-sales service and contacts are available on the Internet

at: www.2helpU.com

9

ENGLISH

Technical data

KS600E/KS601E

KS602E/KS603E(Type 1)

Input voltage V

AC

230

Power input W 450

No-load speed min

-1

0-3,000

Max. depth of cut

Wood mm 60

Steel mm 5

Aluminium mm 10

Weight kg 1.9

Level of sound pressure according to EN 60745:

Sound pressure (L

pA

) 89 dB(A), uncertainty (K) 3 dB(A)

Sound power (L

WA

) 100 dB(A), uncertainty (K) 3 dB(A)

Vibration total values (triax vector sum) according to

EN 60745:

Cutting wood (a

h,cw

) 7.7 m/s

2

, uncertainty (K) 2.4 m/s

2

Cutting sheet metal (a

h,cm

) 9.1 m/s

2

, uncertainty (K) 1.5 m/s

2

EC declaration of conformity

MACHINERY DIRECTIVE

%

KS600E/KS601E/KS602E/KS603E

Black & Decker declares that these products described under

"technical data" are in compliance with:

2006/42/EC, EN 60745-1, EN 60745-2-11

For more information, please contact Black & Decker at the

following address or refer to the back of the manual.

The undersigned is responsible for compilation of the technical

le and makes this declaration on behalf of Black & Decker.

_

Kevin Hewitt

Vice-President Global Engineering

Black & Decker Europe, 210 Bath Road, Slough,

Berkshire, SL1 3YD

United Kingdom

31/03/2010

Guarantee

Black & Decker is condent of the quality of its products and

offers an outstanding guarantee. This guarantee statement is

in addition to and in no way prejudices your statutory rights.

The guarantee is valid within the territories of the Member

States of the European Union and the European Free Trade

Area.

If a Black & Decker product becomes defective due to faulty

materials, workmanship or lack of conformity, within 24 months

from the date of purchase, Black & Decker guarantees to

replace defective parts, repair products subjected to fair wear

and tear or replace such products to ensure minimum

inconvenience to the customer unless:

u The product has been used for trade, professional or hire

purposes;

u The product has been subjected to misuse or neglect;

u The product has sustained damage through foreign

objects, substances or accidents;

u Repairs have been attempted by persons other than

authorised repair agents or Black & Decker service staff.

To claim on the guarantee, you will need to submit proof of

purchase to the seller or an authorised repair agent. You can

check the location of your nearest authorised repair agent by

contacting your local Black & Decker ofce at the address

indicated in this manual. Alternatively, a list of authorised

Black & Decker repair agents and full details of our after-sales

service and contacts are available on the Internet at:

www.2helpU.com

Please visit our website www.blackanddecker.co.uk to

register your new Black & Decker product and to be kept up to

date on new products and special offers. Further information

on the Black & Decker brand and our range of products is

available at www.blackanddecker.co.uk

Page is loading ...

ENGLISH

Do not forget to register your product!

www.blackanddecker.co.uk/productregistration

Register your product online at www.blackanddecker.co.uk/

productregistration or send your name, surname and product code to

Black & Decker in your country

.

DEUTSCH

Vergessen Sie nicht, Ihr Produkt registrieren zu lassen!

www.blackanddecker.de/productregistration

Lassen Sie Ihr Produkt unter www.blackanddecker.de/

productregistration online registrieren oder schicken Sie Ihren

Nachnamen, Vornamen und den Produktcode an Black & Decker in

Ihrem Land.

FRANÇAIS

N’oubliez pas d’enregistrer votre produit !

www.blackanddecker.fr/productregistration

Enregistrez votre produit en ligne sur www.blackanddecker.fr/

productregistration ou envoyez vos nom, prénom et code produit à

Black & Decker dans votre pays.

ITALIANO

Non dimenticate di registrare il prodotto!

www.blackanddecker.it/productregistration

Registrate il prodotto online su www.blackanddecker.it/

productregistration o inviate nome, cognome e codice del prodotto al

centro Black & Decker del vostro paese.

NEDERLANDS

Vergeet niet uw product te registreren!

www.blackanddecker.nl/productregistration

U kunt uw product online registreren op www.blackanddecker.nl/

productregistration of u kunt uw voornaam, achternaam en

productcode opsturen naar Black & Decker in uw land.

ESPAÑOL

¡No olvide registrar su producto!

www.blackanddecker.es/productregistration

Registre su producto on-line en www.blackanddecker.es/

productregistration o envíe su nombre, apellidos y código de

producto a Black & Decker en su país.

PORTUGUÊS

Não se esqueça de registar o seu produto!

www.blackanddecker.pt/productregistration

Registe o seu produto online em www.blackanddecker.pt/

productregistration ou envie o seu nome, apelido e código do

produto para a Black & Decker no seu país.

SVENSKA

Glöm inte att registrera produkten!

www.blackanddecker.se/productregistration

Registrera produkten online på www.blackanddecker.se/

productregistration eller skicka namn och produktkod till

Black & Decker i landet du bor i.

NORSK

Ikke glem å registrere produktet ditt!

www.blackanddecker.no/productregistration

Registrer produktet ditt online på www.blackanddecker.no/

productregistration, eller send ditt navn, etternavn og produktkode til

Black & Decker i ditt eget land.

DANSK

Glem ikke at registrere dit produkt!

www.blackanddecker.dk/productregistration

Registrer dit produkt på internettet på: www.blackanddecker.dk/

productregistration eller send dit navn, efternavn og produktkode til

Black & Decker i dit eget land.

SUOMI

Muistathan rekisteröidä tuotteesi!

www.blackanddecker./productregistration

Rekisteröi tuotteesi verkossa osoitteessa www.blackanddecker./

productregistration tai lähetä etunimesi, sukunimesi ja tuotekoodi

oman maasi Black & Decker -edustajalle.

Ε Λ Λ Η Ν Ι Κ Α

Μηνξεχάσετενακαταχωρίσετετοπροϊόνσας!

www.blackanddecker.gr/productregistration

Καταχωρίστε το προϊόν σας σε σύνδεση στη σελίδα www.

blackanddecker.gr/productregistration ή στείλτε το όνομα, επίθετο

σας και τον κωδικό πριονωτός στη Black & Decker στη χώρα σας.

Page is loading ...

Black & Decker KS602E T1 Owner's manual

Related papers

Other documents