Gaggia SIN 042 GM User manual

Italiano

Type HD 8525 / HD8527

ISTRUZIONI PER L'USO

OPERATING INSTRUCTIONS

BEDIENUNGSANLEITUNG

MODE D’EMPLOI

INSTRUCCIONES DE USO

INSTRUÇÕES DE USO

LEGGERE ATTENTAMENTE QUESTE ISTRUZIONI D'USO PRIMA DI UTILIZZARE LA MACCHINA.

READ THESE INSTRUCTIONS CAREFULLY BEFORE USING THE MACHINE.

VOR DEM GEBRAUCH DER MASCHINE IST DIE VORLIEGENDE BEDIENUNGSANLEITUNG AUFMERKSAM ZU LESEN.

LIRE ATTENTIVEMENT CE MODE D'EMPLOI AVANT D’UTILISER LA MACHINE.

LEER ATENTAMENTE ESTAS INSTRUCCIONES DE USO ANTES DE USAR LA MÁQUINA.

LEIA ATENTAMENTE ESTAS INSTRUÇÕES DE USO ANTES DE UTILIZAR A MÁQUINA.

Register your product and get support at

www.philips.com/welcome

EnglishDeutschFrançaisEspañolPortuguês

• 2 •

Fig. - Abb. - Afb. - Rys. - Kuva. - Εικ. (A) Fig. - Abb. - Afb. - Rys. - Kuva. - Εικ. (B)

20 cm

8 in

20 cm

8 in

20 cm

8 in

40 cm

16 in

20 cm

8 in

1

2 3

6

7

14 15 16 17 18

9

10 12

11 13

19

24

25

23

22

20

21

4

5

8

Page is loading ...

• 16 •

IMPORTANT SAFEGUARDS

When using electrical appliances, basic safety precautions should always be

followed, including the following:

1. Read all instructions.

2. Do not touch hot surfaces. Use handles or knobs.

3. To protect against  re, electric shock and injury to person do not immerse

cord, plugs, or machine in water or other liquid.

4. Close supervision is necessary when the appliance is used by or near children.

5. Unplug from outlet when not in use and before cleaning. Allow to cool

before putting on or taking o parts, and before cleaning the appliance.

6. Do not operate any appliance with a damaged cord or plug or after the

appliance malfunctions, or has been damaged in any manner. Return

appliance to the nearest authorized service facility for examination, repair

or adjustment.

7. The use accessory attachments not recommended by the appliance

manufacturer may result in  re, electric shock or injury to persons.

8. Do not use outdoors.

9. Do not let cords hang over edge of table or counter, or touch hot surfaces.

10. Do not place on or near a hot gas or electric burner, or in a heated oven.

11. Always attach plug to appliance  rst, then plug cord into wall outlet. To

disconnect, turn any control to “o ”, then remove plug from wall outlet.

12. Do not use appliance for other than intended use.

13. Save these Instructions.

SAVE THESE INSTRUCTIONS

• 17 •

English

INSTRUCTIONS FOR THE POWER

SUPPLY CORD

A. A short power-supply cord (or detachable power-supply cord) is to be

provided to reduce risks resulting from becoming entangled in or tripping

over a longer cord.

B. Longer detachable power-supply cords or extension cords are available and

may used if care is exercised in their use.

C. If a long detachable power-supply cord or extension cord is used,

1. The marked electrical rating of the detachable power-supply cord or

extension cord should be at least as great as the electrical rating of the

appliance

2. If the appliance is of the grounded type, the extension cord should be a

grounding-type 3-wire cord, and

3. The longer cord should be arranged so that it will not drape over the

counter top or table top where it can be pulled on by children or tripped

over.

• 18 •

1 General Information

The co ee machine is suitable for preparing 1 or 2 cups of

espresso co ee and is provided with a swivel steam and hot

water wand. The controls on the front side of the machine are

labelled with easy-to-read symbols.

The machine has been designed for domestic use and is not

suitable for professional, continuous use.

Warning. No liability is held for damage caused

by:

• Incorrect use not in accordance with the intended

purposes;

• Repairs not carried out in authorised service cen-

tres;

• Tampering with the power cord;

• Tampering with any part of the machine;

• Use of non-original spare parts and accessories;

• Failure to descale the machine and storage at tem-

peratures below 0°C.

In these cases, the warranty is void.

1.1 To Simplify Manual Reading

The warning triangle indicates

all important instructions for the

user’s safety. Carefully follow these

instructions to avoid serious injury!

References to illustrations, parts of the appliance or controls,

etc. are indicated by numbers or letters. Whenever possible,

refer to the illustration.

This symbol is used to highlight information

that is particularly important to ensure opti-

mal use of the machine.

The illustrations corresponding to the text can be

found on the  rst pages of the manual. Please refer to

these pages while reading the operating instructions.

1.2 How to Use these Operating Instruc-

tions

Keep these operating instructions in a safe place and make

them available to anyone who may use the co ee machine.

For further information or in case of problems, please refer to

an authorised service centre.

2 Technical Specifications

The manufacturer reserves the right to make changes to the

technical speci cations of the product.

Nominal Voltage - Power Rating - Power Supply

See label on the appliance

Housing Material

Plastic model HD8525

Metal model HD8527

Size (w x h x d) (mm)

210 x 300 x 280

Weight (kg)

HD 8525 = 3.9

HD 8527 = 5.4

Power Cord Length

1.3 m

Control Panel

Front side

Filter Holder

Pressurized type

Pannarello

Special for cappuccinos

Water Tank

1.25 litres - Removable type

Pump Pressure

15 bar

Boiler

Stainless steel

Safety Devices

Thermal fuse

3 Safety Regulations

Never allow water to come into contact with any of the

electrical parts of the machine: Danger of short circuit!

Overheated steam and hot water may cause burning!

Never direct the steam or hot water jet towards body

parts. Handle the steam/hot water spout with care:

danger of scalding!

Intended Use

This co ee machine is intended for domestic use only. The use

by children older than 8 years and by persons with reduced

physical, mental or sensory abilities or with lack of experience

and skills is allowed, provided that they are supervised or in-

structed on how to use the appliance correctly and that they

understand the hazards involved. Children must not play with

the appliance. Children must not carry out any cleaning and

• 19 •

English

maintenance operations without being monitored.

Power Supply

Connect the co ee machine only to a suitable socket. The volt-

age must correspond to that indicated on the appliance label.

Power Cord

Never use the co ee machine if the power cord is defective or

damaged. If the power cord is damaged, it must be replaced

by the manufacturer or by its authorised service centre. Do not

pass the power cord around corners, over sharp edges or over

hot objects and keep it away from oil.

Do not use the power cord to carry or pull the co ee machine.

Do not pull out the plug by the power cord or touch it with wet

hands. Do not let the power cord hang freely from tables or

shelves.

For the Safety of Others

Prevent children from playing with the machine. Children are

not aware of the risks related to electrical household appli-

ances. Do not leave the machine packaging materials within

the reach of children.

Danger of burns

Never direct jets of overheated steam and/or hot water to-

wards yourself or others. Do not touch the steam wand with

bare hands. Always use the handles or knobs provided.

Do not disconnect (remove) the pressurized  lter holder while

co ee is brewed.

Hot water drips may spill out of the brew unit during the

warm-up phase.

Do not touch the brew unit when the machine is on or before

it cools down.

Location

Place the co ee machine in a safe place, where there will be no

danger of overturning or injury. Hot water or overheated steam

may spill out of the machine: danger of scalding!

Do not keep the machine at a temperature below 0°C. Frost

may damage it.

Do not use the co ee machine outdoors.

In order to prevent its housing from melting or being dam-

aged, do not place the machine on very hot surfaces and close

to open  ames.

Cleaning

Before cleaning the machine, turn it o by pressing the ON/OFF

button, then remove the plug from the socket. Wait also for the

machine to cool down.

Never immerse the machine in water!

It is strictly forbidden to tamper with the internal parts of the

machine. Water left in the tank for several days should not be

consumed. Wash the tank and  ll it with fresh drinking water.

Suitable Location for Operation and Mainte-

nance

In order to ensure correct and e cient performance of the cof-

fee machine, we recommend following the instructions below:

• Choose a level surface.

• Choose a location that is su ciently well-lit, clean and

near an easily reachable socket.

• Allow for a minimum distance from the sides of the

machine as shown in Fig. A.

Storing the Machine

If the machine is to remain inactive for a long time, turn it o

and unplug it. Store the machine in a dry place, out of the reach

of children. Keep it protected from dust and dirt.

Do not keep the machine at a temperature below 0°C. Frost

may damage it.

Repairs / Maintenance

In case of failure, problems or a suspected fault resulting from

the falling of the machine, immediately remove the plug from

the socket. Never attempt to operate a faulty machine. Servic-

ing and repairs may only be carried out by Authorised Service

Centres. All liability for damages resulting from work not car-

ried out by professionals is declined.

Fire Safety Precautions

In case of  re, use carbon dioxide (CO

2

) extinguishers. Do not

use water or dry powder extinguishers.

Key to Machine Parts (Page 2)

1 Control panel

2 Cup holder rest

3 Hot water/steam knob

4 Co ee brew unit

5 Water tank

6 Water recovery tray

7 Cup holder grill

8 Steam wand (Pannarello)

9 Power cord socket

10 ON/OFF button

11 "Co ee brew" button

12 "Steam" button

13 "Rinsing" button

14 "Temperature" light

15 "Descaling" light

16 "Alarm" light

17 "Steam" light

18 "Rinsing" light

19 Pressurized  lter holder

20 Ground co ee measuring scoop

21 Power cord

• 20 •

22 Ground co ee  lter

(single piece for 1 or 2 co ee(s))

23 Co ee pod  lter adapter

24 Co ee pod  lter

25 "Intenza+" water  lter (sold separately)

4 Installation

For your own and other people safety, carefully follow

the "Safety Regulations" indicated in chapter 3.

4.1 Packaging

The original packaging has been designed and manufactured

to protect the machine during transport. We recommend

keeping the packaging material for possible future transport.

4.2 Installation Precautions

Do not move the machine by grabbing the cup

protection grilles.

Before installing the machine, read the following safety pre-

cautions carefully:

• Place the machine in a safe place.

• Make sure children cannot play with the machine.

• Do not place the machine on hot surfaces or near open

 a m e s .

The co ee machine is now ready to be connected to the electric

network.

Note: we recommend washing the components

before using them for the  rst time and/or af-

ter they have not been used for a certain period of time.

4.3 Water tank

•

1

Remove the water tank (5).

•

2

Rinse it and  ll it with fresh drinking water, making

sure that the (MAX) level indicated in the tank is not

exceeded.

Fill the tank only with fresh, non-sparkling,

drinking water. Hot water or any other liquid

may damage the tank. Do not operate the machine

when the water level in the tank is below the MIN

threshold. Make sure there is enough water in the wa-

ter tank.

• Insert the water tank into its seat in the co ee machine

and make sure that it locks into place - its pro le should

adhere to that of the co ee machine.

Note: the water level can be checked looking

through the window on the front side of the

tank.

4.4 Machine Connection

Electric power may be very dangerous! It is

therefore necessary to strictly follow the safety

regulations. Do not use faulty power cords. Faulty cords

and plugs must be replaced immediately by Authorised

Service Centres.

The voltage of the appliance has been pre-set by the manu-

facturer. Check that the voltage matches the indication on the

data plate at the bottom of the appliance.

•

3A

Insert the plug into the socket on the back of the

machine.

•

3B

Insert the other end of the plug into a wall socket with

suitable power voltage.

4.5 First Use

At  rst start-up, the co ee machine circuit must be primed.

4

Press the ON/OFF button (10); when the (14 )" ", (16 )"

" and (17) lights " " start blinking, the circuit must

be primed.

5

Place a container under the steam wand (Pannarello).

Open the "hot water/steam" knob (3) by turning it

clockwise. The pump is activated automatically. Wait

until a steady jet of water  ows out of the steam wand

(Pannarello).

6

Close the "hot water/steam" knob (3) by turning it

counter-clockwise. Remove the container.

The machine begins the warm-up phase only after the water

circuit has been correctly primed.

Note: if the knob is left open, the pump is auto-

matically disengaged after a few seconds and

the "

" light (16) starts blinking.

• 21 •

English

4.6 Circuit Priming

When the water tank is empty, the machine circuit must be

primed again.

Note: if the machine has been operating with-

out water for a lot of time and the "

" (14), " "

(16) and "

" (17) lights are blinking, please refer to the

"Troubleshooting" table.

•

5

Place a container under the steam wand (Pannarello).

• Open the "hot water/steam" knob (3) by turning it

clockwise. The pump is activated automatically.

• Wait until a steady jet of water  ows out of the steam

wand (Pannarello).

•

6

Close the "hot water/steam" knob (3) by turning it

counter-clockwise. Remove the container.

Note: if the steam knob is opened by mistake

during the warm-up phase, the "

" light (16)

starts blinking. Close the knob and wait until the ma-

chine is ready.

4.7 Using the Machine for the First Time or

After a Period of Inactivity

This simple operation ensures an optimum brewing and must

be performed:

- at  rst start-up;

- when the machine remains inactive for a long time (more

than 2 weeks).

Dispensed water must be emptied into an ad-

equate drain. It is not suitable for food use. If

the container  lls up during the cycle, stop dispensing

water and empty the container before resuming the

operation.

A

2

Rinse the water tank and re ll it with fresh drinking

water. Insert the water tank back into its seat in the co ee

machine and make sure that it locks into place - its pro le

should adhere to that of the co ee machine.

B Turn on the machine by pressing the (10) button. Wait until

the "

" light (14) turns on steady.

C

5

Place a container under the steam wand (Pannarello).

Open the knob (3) by turning it clockwise. The pump is

activated automatically.

D Dispense the whole water tank content from the steam/

hot water wand (Pannarello); to stop the dispensing

process, close the knob (3) by turning it counter-clockwise.

During this operation the pump is automati-

cally disengaged and the "

" light (16) is

blinking: this is a normal behaviour of the machine.

Close the knob. Wait until the "

" light (14) is steady on

before opening the knob again.

E

2

Fill the water tank with fresh drinking water. Insert

the water tank back into its seat in the co ee machine and

make sure that it locks into place - its pro le should adhere

to that of the co ee machine.

F

13

14

Insert the  lter holder into the brew unit (4) from

the bottom and turn it from left to right until it locks into

place.

G

15

Place a suitable container under the  lter holder.

H

17

Press the " " button and dispense a cup of hot

water.

At the end of the process, stop the operation by pressing

the "

" button.

I Repeat the operations described in step (H) until the

water tank is completely empty.

L

2

Re ll the water tank with fresh drinking water.

M

19

Remove the  lter holder from the unit by turning it

from right to left and rinse it with fresh drinking water.

Now the machine is ready. Please see related chapters for oper-

ating details on how to brew co ee and dispense steam.

5 Rinsing

Note: make sure the  lter holder is inserted to

ensure a proper warm-up of the machine.

The machine is set so as to automatically rinse the co ee circuit

with fresh water every time it is turned on. This is conceived to

ensure the correct machine warm-up and an optimum co ee

aroma.

Place a container under the dispensing spout.

On newly purchased machines this function is active (the "

"

light (18) is on) and is performed at the end of the warm-up

phase, when the "

" light (14) is steady on.

Note: should no water pour from the  lter

holder, perform a manual rinse as described in

sect. 7.1.

The rinsing procedure may:

A be stopped by pressing the "

" or " " button;

• 22 •

B be deactivated by pressing the " " button while the " "

light (14) is blinking or steady-on. In this case the "

" light

(18) turns o .

Note: if the rinsing procedure is deactivated,

it can be reactivated only by pressing the "

"

button.

6 Energy Saving

The machine is designed for energy saving.

After 9 minutes of inactivity, the machine turns o in order to

save energy and respect nature.

Press the ON/OFF "

" button (10) to operate the machine.

7 Coffee Brewing

Warning! During the co ee brewing it is forbid-

den to remove the pressurized  lter holder by

manually turning it clockwise. Danger of burns!

• During this operation, the "

" light (14) is blinking; this is

to be considered as a standard and not a faulty operating

mode.

• Before using the machine, make sure that there is enough

water in the machine tank.

Note: if the steam knob is opened by mistake

during the warm-up phase, the "

" light (16)

starts blinking. Close the knob and wait until the ma-

chine is ready.

If co ee is NOT brewed after pressing the brew

button "

" (11), press the "co ee cup" brew

button (11) again and check the "Troubleshooting" ta-

ble before removing the  lter holder.

Ensure the machine is ready before brewing co ee. The ma-

chine is ready when the "

" light (14) is steady on.

7.1 Filter Holder Warm-Up

If the "rinse" function is not activated and/or the  lter holder is

to be warmed-up manually, do as follows:

•

13

Insert the pressurized  lter holder into the brew unit

(4) from the bottom.

•

14

Turn the pressurized  lter holder from left to right

until it locks into place. Release the pressurized  lter

holder grip. The handle will turn slightly to the left. This

movement guarantees optimum  lter holder performance.

•

17

Preheat the pressurized  lter holder by pressing the "

" button; some water will  ow out of the pressurized

 lter holder (this operation is necessary only for the  rst

co ee).

• After 50cc of water have been dispensed, press the "

"

button again to stop the dispensing procedure.

•

19

Remove the pressurized  lter holder by turning it from

right to left and then drain the remaining water.

Place a container under the dispensing spout.

Now you can go on with the co ee brewing procedures de-

scribed in the following sections.

7.2 Using Ground Co ee

•

7

Insert the  lter (22) in the pressurized  lter holder

(19); the  lter is already inserted when using the machine

for the  rst time. As the machine is  tted with the special

 lter (22), there is no need to change the  lter to prepare

either one or two co ees.

•

8

Add 1-1.5 measuring scoop(s) for a single co ee and 2

measuring scoops for a double co ee. Remove any co ee

residues from the rim of the pressurized  lter holder.

Note: do not press the co ee, since the  lter

holder is provided with an optimized system

for original espresso brewing.

•

13

Insert the  lter holder (19) into the brew unit (4) from

the bottom.

•

14

Turn the  lter holder from left to right until it locks

into place.

•

16

Take 1 or 2 preheated cups and place them under

the pressurized  lter holder. Make sure that they are

placed correctly under the co ee brewing nozzles.

•

17

Press the " " button.

•

18

When the desired quantity of co ee has been

brewed, press the "

" button again to stop the brewing

procedure. Wait for a few seconds after brewing, then

remove the cups of co ee.

•

19

After brewing, wait until the

" " light (14)

stops

blinking, then remove the pressurized  lter holder by

turning it from right to left and empty the remaining

co ee grounds.

• 23 •

English

Note: a small quantity of water remains in the

pressurized  lter holder. This has to be consid-

ered as absolutely normal and is due to the  lter holder

characteristics.

Important note: The  lter (22) should be kept

clean to guarantee perfect results. Clean daily

after use.

7.3 Using Co ee Pods

•

9

Remove the ground co ee  lter (22) from the

pressurized  lter holder (19).

•

10

Insert the pod adapter (23) into the pressurized  lter

holder (19) ensuring that its convex part faces down.

•

11

Then insert the pod  lter (24) into the pressurized

 lter holder (19).

•

12

Insert the pod into the  lter holder; make sure that the

paper of the pod does not stick out of the  lter holder.

•

13

Insert the pressurized  lter holder into the brew unit

(4) from the bottom.

•

14

Turn the  lter holder from left to right until it locks

into place.

•

15

Take 1 preheated cup and place it under the  lter

holder. Check that it is placed correctly under the co ee

brewing nozzles.

•

17

Press the " " button.

• When the desired quantity of co ee has been brewed,

press the "

" button again to stop the brewing

procedure. Wait for a few seconds after brewing, then

remove the cup of co ee.

•

19

After brewing, wait until the (14) co ee light stops

blinking, then remove the pressurized  lter holder by

turning it from right to left and dispose of the used pod.

Important note: The  lter (24) and the adapter

(23) should be kept clean to guarantee perfect

results. Clean daily after use.

8 Tips for Choosing Coffee

As a general rule, any type of co ee available on the market

can be used. However, co ee is a natural product and its  a-

vour changes according to its origin and blend; therefore, it is

advisable to try di erent types of co ee in order to  nd out the

blend that best suits your personal tastes. For optimal results,

we recommend using espresso machine blends. As a rule, cof-

fee should always come out of the pressurized  lter holder,

without dripping. The co ee brewing speed can be modi ed

by slightly changing the amount of co ee in the  lter and/or

using a di erent co ee grind. Saeco recommends using ESE

single-dose co ee pods for a tasty co ee and easier cleaning

and preparation.

BEFORE PERFORMING ANY OPERATIONS RELATED

TO HOT WATER/STEAM DISPENSING, MAKE SURE

THAT THE STEAM WAND (PANNARELLO) IS DIRECTED OVER

THE WATER RECOVERY TRAY.

9 Hot Water

Danger of scalding! Dispensing may be preced-

ed by small jets of hot water. The steam wand

may reach high temperatures: never touch it with bare

hands.

•

13

Insert the pressurized  lter holder into the brew unit

(4) from the bottom.

•

14

Turn the pressurized  lter holder from left to right

until it locks into place. Release the pressurized  lter

holder grip. The handle will turn slightly to the left. This

movement guarantees optimum  lter holder performance.

• Press the ON/OFF button (10). The "

" light (14) starts

blinking. Wait until the "

" light (14) turns on steady.

•

5

Place a container or a tea glass under the steam wand

(Pannarello).

• Open the knob (3) by turning it clockwise. The pump is

automatically disengaged and the "

" light (14) turns o .

•

6

When the desired amount of hot water has been

dispensed, close the knob (3) by turning it counter-

clockwise.

• Remove the hot water container.

Note: during this operation the pump is auto-

matically disengaged and the "

" light (16)

is blinking: this is a normal behaviour of the machine.

Close the knob. Wait until the "

" light (14) is steady on

before opening the knob again.

• 24 •

10 Steam / Cappuccino

Danger of scalding! Dispensing may be preceded

by small jets of hot water. The steam wand may

reach high temperatures: never touch it with bare

hands.

•

13

Insert the pressurized  lter holder into the brew unit

(4) from the bottom.

•

14

Turn the pressurized  lter holder from left to right

until it locks into place. Release the pressurized  lter

holder grip. The handle will turn slightly to the left. This

movement guarantees optimum  lter holder performance.

• Press the ON/OFF button (10). The "

" light (14) starts

blinking. Wait until the "

" light (14) turns on steady.

•

21

Press the " " button (12). The " " light (14) turns o

and the "

" light (17) starts blinking.

Note: if the steam knob (3) is opened by mistake

during the warm-up phase, the "

" light (16)

starts blinking. Close the knob and wait until the ma-

chine is ready.

• Wait until the "

" light (17) is steady on. Now the

machine is ready for dispensing steam.

•

22

Place a container under the steam wand.

• Open the knob (3) for a few seconds so that the remaining

water can  ow out of the steam wand (Pannarello). Within

a short time only steam will come out.

•

23

Close the knob (3) and remove the container.

• Fill 1/3 of the container - the one you wish to use to prepare

the cappuccino - with cold milk.

Use cold milk to get a better result.

•

24

Immerse the steam wand in the milk and open the

knob (3) by turning it clockwise; the pump is automatically

engaged. Rotate the milk container with slow upward

movements to obtain uniform warmth.

• Once  nished, close the knob (3) by turning it counter-

clockwise and remove the cup with frothed milk.

• After this operation, clean the steam wand with a wet

cloth.

The same procedure can be used to heat other

beverages.

• To stop the steam dispensing procedure, press the "

"

(12) or "

" button (11). The " " (14), " " (17) and "

" (16) lights blink fast at the same time. This is to indicate

that the machine temperature is too high to brew co ee.

10.1 Machine Cooling

Proceed as follows to lower the temperature:

•

5

Place a container or a tea glass under the steam wand

(Pannarello).

• Open the knob (3) by turning it clockwise.

• When the machine reaches the proper temperature, the

pump is automatically disengaged and the "

" light (16)

is blinking.

6

Close the knob (3) by turning it counter-clockwise and

remove the container.

• Ensure the machine is ready before brewing co ee. The

machine is ready when the "

" light (14) is steady on.

11 Cleaning

Maintenance and cleaning can only be carried out when the

machine is cold and disconnected from the electric network.

• Do not immerse the machine in water or place any of its

parts in a dishwasher.

• Do not use spirit, solvents and/or aggressive chemical

agents.

• We recommend cleaning the water tank and re lling it

with fresh water every day.

•

30

Every week, clean the boiler ring with a wet cloth

when the machine is o , cold and disconnected from the

mains.

•

26

27

Every day, after heating milk, remove the external

part of the Pannarello and wash it with fresh drinking

water.

•

26

27

28

Clean the steam wand weekly. In order to do

this, perform the following operations:

- Remove the external part of the Pannarello (for standard

cleaning);

- Remove the upper part of the Pannarello from the steam

wand;

- Wash the upper part of the Pannarello with fresh drinking

water;

- Wash the steam wand with a wet cloth and remove any

milk residue;

- Re t the upper part in the steam wand (make sure it is

completely inserted);

• 25 •

English

29

After cleaning, reassemble the external part of the

Pannarello and make sure it reaches its limit stop. Make

also sure that the plastic part is correctly  t into the metal

part.

•

31

Empty and wash the drip tray daily.

• Use a soft, dampened cloth to clean the appliance.

•

20

Clean the pressurized  lter holder as follows:

-

9

remove the  lter and wash it thoroughly with hot

water.

- Remove the adapter (if  tted), and wash it thoroughly

with hot water.

- Wash the internal part of the pressurized  lter holder.

• Do not dry the machine and/or its parts using a microwave

and/or standard oven.

Note: do not wash the pressurized  lter holder

in the dishwasher.

12 Descaling

Limescale is a natural part of the water used for machine op-

eration. It needs to be removed regularly as it may clog the

water and co ee circuit of your appliance.

This is an easy procedure with your Philips-Saeco machine.

When the "

" light (15) turns on, descaling is recommended.

When the "

" light (15) turns on, descaling is needed.

This operation needs to be carried out before

the appliance stops working properly, as in this

case repair is not covered by warranty.

Use the Saeco descaling product (Fig. B). Its

formula has been designed to ensure better

machine performance and operation for its whole op-

erating life. If correctly used, it also avoids alterations

in the brewed product. Before starting a descaling cy-

cle make sure that: THE WATER FILTER (if used) HAS BEEN

REMOVED.

Never drink the descaling solution or any prod-

ucts dispensed until the cycle has been carried

out to the end. Never use vinegar as a descaling solu-

tion.

1

13

14

Insert the pressurized  lter holder into the brew

unit (4) from the bottom and turn it from left to right until

it locks into place.

2

1

Remove and empty the water tank.

3

2

Pour HALF the content of the Saeco concentrated

descaling solution into the water tank, then  ll the tank

with fresh drinking water up to the MAX level. Insert the

water tank back into its seat in the co ee machine and

make sure that it locks into place - its pro le should adhere

to that of the co ee machine.

4

Turn on the machine by pressing the ON/OFF " "

button (10).

5

Following the instructions provided in chapter 9 of

this manual, dispense 2 cups of water (about 150ml each)

from the steam wand (Pannarello) and turn the machine

o by pressing the ON/OFF "

" button (10).

5 Let the descaling solution take e ect for approx.15-20

minutes with the machine turned o .

6 Turn on the machine

by pressing the ON/OFF " " button

(10).

5

Following the instructions provided in chapter 9 of

this manual, dispense 2 cups of water (about 150ml each)

from the

steam wand (Pannarello).

Turn o the machine

by

pressing the ON/OFF "

"

button (10) and leave it o for 3

minutes.

7 Repeat the operations described in step 6 until the water

tank is completely empty.

During this operation the pump is automati-

cally disengaged and the "

" light (16) is

blinking: this is a normal behaviour of the machine.

Close the knob. Wait until the "

" light (14) is steady on

before opening the knob again.

8

2

Rinse the water tank with fresh drinking water and  ll

it up.

9 Place a container under the  lter holder.

10 Turn on the machine by pressing the ON/OFF " " button

(10); press the "

" button and dispense the whole content

of the tank by means of the  lter holder. Press the "

"

button again to stop the dispensing process.

11

2

Re ll the tank with fresh water. Insert the water tank

back into its seat in the co ee machine and make sure that it

locks into place - its pro le should adhere to that of the co ee

machine.

5

Place a large container (about 1l capacity) under the

steam wand (Pannarello).

Open the water dispensing knob (3) by turning it clockwise

and dispense the whole content of the water tank by

means of the steam wand (Pannarello).

12

6

After the water dispensing process is complete, close

the water dispensing knob (3) by turning it counter-

clockwise.

• 26 •

13 Repeat the operations once again from step (8), for a total

of 4 tanks.

14

19

Remove the  lter holder from the unit by turning it from

right to left and rinse it with fresh drinking water.

The descaling cycle is now complete.

2

Re ll the tank with fresh water. If necessary, prime the

circuit as described in section 4.5.

At the end, press and hold the "

" (11) and " " (12) buttons

for 3 seconds; the "

" light (15) turns o .

The descaling solution is to be disposed of ac-

cording to the manufacturer’s instructions

and/or the regulations in force in the country of use.

13 "Intenza+" Filter (Optional)

The "INTENZA+" water  lter can improve the quality of water.

Using the "INTENZA+"  lter will prevent limescale from

building up and will ensure a much more intense aroma to

your espresso co ee. We therefore recommend you install the

"INTENZA+" water  lter, which can be purchased from your

local dealer or on-line at the Philips on-line store http://shop.

philips.com or at authorized service centres.

•

34

Remove the small white  lter from the tank and store

it in a dry place sheltered from dust.

•

32

Remove the "INTENZA+" water  lter from its package.

Set the  lter according to the water hardness.

•

33

Immerse the "INTENZA+" water  lter vertically in cold

water (with the opening positioned upwards) and gently

press its sides to let the air bubbles out.

•

35

Put the  lter into the empty tank. Press it until its limit

stop.

• Fill the water tank with fresh drinking water and reinsert it

into the machine.

Carry out the following steps to activate the "Intenza+"

 l t e r :

•

4

Press the ON/OFF button (10). The " " light (14) starts

blinking. Wait until the "

" light (14) turns on steady.

•

5

Place a container or a tea glass under the steam wand

(Pannarello).

• Open the knob (3) by turning it clockwise.

•

6

When about 1 litre of hot water has been dispensed,

close the knob (3) by turning it counter-clockwise.

• Empty the hot water container.

During this operation the pump is automati-

cally disengaged and the "

" light (16) is

blinking: this is a normal behaviour of the machine.

Close the knob. Wait until the "

" light (14) is steady on

before opening the knob again.

Now the  lter is active and the machine is ready for use.

14 Disposal

- The packing materials can be recycled.

- Appliance: unplug the appliance and cut the power cord.

- Deliver the appliance and power cord to a service center or

public waste disposal facility.

This product complies with eu directive 2002/96/EC.

The symbol

on the product or on its packaging indi-

cates that this product may not be treated as household waste.

Instead it shall be handed over to the applicable collection

point for the recycling of electrical and electronic equipment.

By ensuring this product is disposed of correctly, you will help

prevent potential negative consequences for the environment

and human health, which could otherwise be caused by inap-

propriate waste handling of this product. For more detailed in-

formation about recycling of this product, please contact your

local city o ce, your household waste disposal service or the

shop where you purchased the product.

• 27 •

English

Problem Possible Causes Solution

The machine does not switch on.

The machine is not connected to the elec-

tric network.

Connect the machine to the electric network.

The pump is very noisy. No water in the tank.

Fill the tank up with water and prime the circuit

(section 4.6).

The (14) " ", (17) " " and (16)

"

" lights blink simultane-

ously.

This is the  rst start-up or the machine is

overheated.

Make sure the tank is full and fully inserted and

lower the temperature as described in section

10.1.

Co ee is too cold.

The  lter holder is not inserted for pre-

heating (chapter 7).

Preheat the  lter holder.

The cups are cold. Preheat the cups with hot water.

The milk does not froth.

It is not possible to prepare a

cappuccino.

The milk is not suitable: powdered milk,

low-fat milk.

Use whole milk.

Dirty Pannarello. Clean the Pannarello as described in chap. 11.

No water in the tank.

Fill the tank up with water and prime the circuit

(section 4.6).

Co ee is brewed too fast, crema

does not form.

There is too little co ee in the  lter holder. Add co ee (chapter 7).

The grind is too coarse. Use a di erent blend (chapter 8).

Co ee is old or not suitable. Use a di erent blend (chap. 8).

The pod is old or not suitable. Change the pod.

Missing component in the  lter holder.

Make sure that all the components are present

and properly installed.

Co ee does not come out or drips

only.

No water.

Fill the tank up with water and prime the circuit

(section 4.6).

The grind is too  ne. Use a di erent blend (chapter 8).

Co ee tamped in the  lter holder. Shake the ground co ee.

There is too much co ee in the  lter

holder.

Reduce the quantity of co ee in the  lter holder.

The machine has limescale build-up. Descale the machine (chap. 12).

The  lter in the  lter holder is clogged. Clean the  lter (chap. 11).

Not suitable pod. Change type of pod.

Co ee  ows out of the edges.

The  lter holder is not correctly inserted

in the brew unit.

Insert the  lter holder correctly (chapter 7).

The upper rim of the  lter holder is dirty. Clean the rim of the  lter holder.

Pod inserted incorrectly.

Insert the pod correctly. Make sure it does not

come out of the  lter holder.

There is too much co ee in the  lter

holder.

Reduce the quantity of co ee using the measur-

ing scoop.

The "

" light (16) is on.

The water knob (3) is open. Close the knob (3).

The " " light (15) is on.

Descale the machine. Please refer to chapter 12.

The pump turns o during water

or steam dispensing and

the "

" light (16) turns on.

Safety time-out. Close the water knob.

Please contact an authorised service centre for any problems not covered in the above table or when the suggested

solutions do not solve the problem. Refer to the www.Philips.com/Support website.

Page is loading ...

Rev.00 del 30-10-12

Il produttore si riserva il diritto d`apportare qualsiasi modifica senza preavviso.

The manufacturer reserves the right to make changes without prior notice.

Der Hersteller behält sich das Recht vor, Änderungen jeder Art ohne Vorankündigung vorzunehmen.

Le producteur se réserve le droit d’apporter des modiﬁ cations sans aucun préavis.

El fabricante se reserva el derecho de modiﬁ car el producto sin aviso previo.

O fabricante reserva-se o direito de efectuar qualquer alteração sem aviso prévio.

www.philips.com/saeco

Gaggia SIN 042 GM User manual

Gaggia SIN 042 GM User manual

in other languages

Related papers

Other documents