Hitachi DV-P533U User manual

Brand: Hitachi

Model: DV-P533U

Category: DVD players

Type: User manual

This manual is also suitable for

SERVICE MANUAL

DVD PLAYER

SPECIFICATIONS AND PARTS ARE SUBJECT TO CHANGE FOR IMPROVEMENT

TK No. 9301E

2003 Digital Media Division, TokaiFebruary

DV-P735U

DV-P735U(C)

DV-P533U

CONTENTS

1 CAUTIONS FOR SAFETY IN PERFORMING

REPAIR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1

1-1 LASER BEAM SAFETY PRECAUTIONS . . . . . . . . 1-1

1-2 IMPORTANT SAFETY PRECAUTIONS . . . . . . . . . 1-2

1-2-1 Product Safety Notice . . . . . . . . . . . . . . . . . . . . . 1-2

1-2-2 Precautions during Servicing . . . . . . . . . . . . . . . 1-2

1-2-3 Safety Check after Servicing . . . . . . . . . . . . . . . . 1-3

1-3 STANDARD NOTES FOR SERVICING . . . . . . . . . . 1-4

1-3-1 Circuit Board Indications . . . . . . . . . . . . . . . . . . . 1-4

1-3-2 Instructions for Connectors . . . . . . . . . . . . . . . . . 1-4

1-3-3 How to Remove/Install Flat Pack-IC . . . . . . . . . . 1-4

1-3-4 Instructions for Handling Semi-conductors . . . . . 1-6

2 GENERAL INFORMATION . . . . . . . . . . . . . . . . .2-1

2-1 SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

2-2 COMPARISON OF MODELS. . . . . . . . . . . . . . . . . . 2-2

2-3 OPERATING CONTROLS AND FUNCTIONS. . . . . 2-4

3 MAINTENANCE AND INSPECTION. . . . . . . . . .3-1

3-1 TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . 3-1

3-2 FIRMWARE RENEWAL MODE . . . . . . . . . . . . . . . . 3-7

3-2-1 How to Update the Firmware Version . . . . . . . . . 3-7

3-2-2 How to Verify the Firmware Version . . . . . . . . . . 3-8

4 DISASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . .4-1

4-1 CABINET DISASSEMBLY INSTRUCTIONS . . . . . . 4-1

4-1-1 Disassembly Flowchart . . . . . . . . . . . . . . . . . . . . 4-1

4-1-2 Disassembly Method . . . . . . . . . . . . . . . . . . . . . . 4-1

5 EXPLODED VIEW AND PARTS LIST. . . . . . . . .5-1

5-1 EXPLODED VIEW . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1

5-2 REPLACEMENT PARTS LIST . . . . . . . . . . . . . . . . . 5-2

5-2-1 Mechanical Parts List . . . . . . . . . . . . . . . . . . . . . 5-2

5-2-2 Electrical Parts List . . . . . . . . . . . . . . . . . . . . . . . 5-3

SCHEMATIC AND BLOCK DIAGRAMS/CBA'S

1 SCHEMATIC DIAGRAMS/CBA’S AND TEST POINTS . 1

2 WIRING DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

3 SCHEMATIC DIAGRAMS . . . . . . . . . . . . . . . . . . . . . . . . 4

3-1 DVD Main 1/3 Schematic Diagram . . . . . . . . . . . . . . . 4

3-2 DVD Main 2/3 Schematic Diagram . . . . . . . . . . . . . . . 5

3-3 DVD Main 3/3 Schematic Diagram . . . . . . . . . . . . . . . 7

3-4 AV 1/3 Schematic Diagram . . . . . . . . . . . . . . . . . . . . . 8

3-5 AV 2/3 Schematic Diagram . . . . . . . . . . . . . . . . . . . . . 9

3-6 AV 3/3 & Function Schematic Diagram . . . . . . . . . . . 10

4 WAVEFORMS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

5 CIRCUIT BOARD DIAGRAMS . . . . . . . . . . . . . . . . . . . 12

5-1 AV CBA Top View . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

5-2 AV CBA Bottom View. . . . . . . . . . . . . . . . . . . . . . . . . 13

5-3 Function CBA Top/Bottom View . . . . . . . . . . . . . . . . 14

6 BLOCK DIAGRAMS . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

6-1 System Control/Servo Block Diagram . . . . . . . . . . . . 15

6-2 Digital Signal Process Block Diagram . . . . . . . . . . . . 16

6-3 Video/Audio Block Diagram . . . . . . . . . . . . . . . . . . . . 17

6-4 Power Supply Block Diagram. . . . . . . . . . . . . . . . . . . 18

7 SYSTEM CONTROL TIMING CHARTS . . . . . . . . . . . . 19

8 IC PIN FUNCTION DESCRIPTIONS . . . . . . . . . . . . . . 20

9 LEAD IDENTIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . 21

1-1

Drive Mecha Assembly

Laser Beam Radiation

Laser Pickup

Turntable

1-1 LASER BEAM SAFETY PRECAUTIONS

This DVD player uses a pickup that emits a laser beam.

The laser beam is emitted from the location shown in the figure. When checking the laser diode, be sure to keep

your eyes at least 30cm away from the pickup lens when the diode is turned on. Do not look directly at the laser

beam.

Caution: Use of controls and adjustments, or doing procedures other than those specified herein, may result in

hazardous radiation exposure.

Do not look directly at the laser beam coming

from the pickup or allow it to strike against your

skin.

Location: Inside Top of DVD mechanism.

LASER RADIATION

WHEN OPEN. DO NOT

STARE INTO BEAM.

CAUTION

CAUTION FOR SAFETY IN PERFORMING REPAIR

1-2

1-2 IMPORTANT SAFETY PRECAUTIONS

1-2-1 Product Safety Notice

Some electrical and mechanical parts have special

safety-related characteristics which are often not evi-

dent from visual inspection, nor can the protection they

give necessarily be obtained by replacing them with

components rated for higher voltage, wattage, etc.

Parts that have special safety characteristics are iden-

tified by a # on schematics and in parts lists. Use of a

substitute replacement that does not have the same

safety characteristics as the recommended replace-

ment part might create shock, fire, and/or other haz-

ards. The Product’s Safety is under review

continuously and new instructions are issued when-

ever appropriate. Prior to shipment from the factory,

our products are carefully inspected to confirm with

the recognized product safety and electrical codes of

the countries in which they are to be sold. However, in

order to maintain such compliance, it is equally impor-

tant to implement the following precautions when a set

is being serviced.

1-2-2 Precautions during Servicing

A. Parts identified by the # symbol are critical for

safety. Replace only with part number specified.

B. In addition to safety, other parts and assemblies

are specified for conformance with regulations

applying to spurious radiation. These must also be

replaced only with specified replacements.

Examples: RF converters, RF cables, noise block-

ing capacitors, and noise blocking filters, etc.

C. Use specified internal wiring. Note especially:

1)Wires covered with PVC tubing

2)Double insulated wires

3)High voltage leads

D. Use specified insulating materials for hazardous

live parts. Note especially:

1)Insulation tape

2)PVC tubing

3)Spacers

4)Insulators for transistors

E. When replacing AC primary side components

(transformers, power cord, etc.), wrap ends of

wires securely about the terminals before solder-

ing.

F. Observe that the wires do not contact heat produc-

ing parts (heatsinks, oxide metal film resistors, fus-

ible resistors, etc.).

G. Check that replaced wires do not contact sharp

edges or pointed parts.

H. When a power cord has been replaced, check that

5 - 6 kg of force in any direction will not loosen it.

I. Also check areas surrounding repaired locations.

J. Be careful that foreign objects (screws, solder

droplets, etc.) do not remain inside the set.

K. Crimp type wire connector

The power transformer uses crimp type connectors

which connect the power cord and the primary side

of the transformer. When replacing the transformer,

follow these steps carefully and precisely to prevent

shock hazards.

Replacement procedure

1)Remove the old connector by cutting the wires at a

point close to the connector.

Important: Do not re-use a connector. (Discard it.)

2)Strip about 15 mm of the insulation from the ends

of the wires. If the wires are stranded, twist the

strands to avoid frayed conductors.

3)Align the lengths of the wires to be connected.

Insert the wires fully into the connector.

4)Use a crimping tool to crimp the metal sleeve at its

center. Be sure to crimp fully to the complete clo-

sure of the tool.

L. When connecting or disconnecting the internal

connectors, first, disconnect the AC plug from the

AC outlet.

1-3

1-2-3 Safety Check after Servicing

Examine the area surrounding the repaired location for

damage or deterioration. Observe that screws, parts,

and wires have been returned to their original posi-

tions. Afterwards, do the following tests and confirm

the specified values to verify compliance with safety

standards.

1. Clearance Distance

When replacing primary circuit components, confirm

specified clearance distance (d) and (d’) between sol-

dered terminals, and between terminals and surround-

ing metallic parts. (See Fig. 1)

Table 1 : Ratings for selected area

Note: This table is unofficial and for reference only.

Be sure to confirm the precise values.

2. Leakage Current Test

Confirm the specified (or lower) leakage current

between B (earth ground, power cord plug prongs)

and externally exposed accessible parts (RF termi-

nals, antenna terminals, video and audio input and

output terminals, microphone jacks, earphone jacks,

etc.) is lower than or equal to the specified value in the

table below.

Measuring Method (Power ON) :

Insert load Z between B (earth ground, power cord

plug prongs) and exposed accessible parts. Use an

AC voltmeter to measure across the terminals of load

Z. See Fig. 2 and the following table.

AC Line Voltage Clearance Distance (d) (d’)

120 V

≥ 3.2mm (0.126 inches)

Table 2: Leakage current ratings for selected areas

Note: This table is unofficial and for reference only. Be sure to confirm the precise values.

AC Line Voltage Load Z Leakage Current (i) Earth Ground (B) to:

120 V

0.15µF CAP. & 1.5kΩ RES.

Connected in parallel

i≤0.5mA Peak Exposed accessible parts

Chassis or Secondary Conductor

dd'

Primary Circuit Terminals

AC Voltmeter

(High Impedance)

Exposed Accessible Part

Earth Ground

Power Cord Plug Prongs

1.5k

0.15 F

Fig. 1

Fig. 2

1-4

1-3 STANDARD NOTES FOR SERVICING

1-3-1 Circuit Board Indications

a. The output pin of the 3 pin Regulator ICs is indi-

cated as shown.

b. For other ICs, pin 1 and every fifth pin are indicated

as shown.

c. The 1st pin of every male connector is indicated as

shown.

1-3-2 Instructions for Connectors

1. When you connect or disconnect the FFC (Flexible

Foil Connector) cable, be sure to first disconnect

the AC cord.

2. FFC (Flexible Foil Connector) cable should be

inserted parallel into the connector, not at an angle.

1-3-3 How to Remove / Install Flat

Pack-IC

1. Removal

With Hot-Air Flat Pack-IC Desoldering Machine:.

(1) Prepare the hot-air flat pack-IC desoldering

machine, then apply hot air to the Flat Pack-IC

(about 5 to 6 seconds). (Fig. S-1-1)

(2) Remove the flat pack-IC with tweezers while apply-

ing the hot air.

(3) Bottom of the flat pack-IC is fixed with glue to the

CBA; when removing entire flat pack-IC, first apply

soldering iron to center of the flat pack-IC and heat

up. Then remove (glue will be melted). (Fig. S-1-6)

(1) Release the flat pack-IC from the CBA using twee-

zers. (Fig. S-1-6)

Caution:

1. Do not supply hot air to the chip parts around the

flat pack-IC for over 6 seconds because damage to

the chip parts may occur. Put masking tape around

the flat pack-IC to protect other parts from damage.

(Fig. S-1-2)

2. The flat pack-IC on the CBA is affixed with glue, so

be careful not to break or damage the foil of each

pin or the solder lands under the IC when removing

it.

Top View

Out

Bottom View

Input

Pin 1

FFC Cable

Connector

CBA

* Be careful to avoid a short circuit.

Fig. S-1-1

Hot-air

Flat Pack-IC

Desoldering

Machine

CBA

Flat Pack-IC

Tweezers

Masking

Tape

Fig. S-1-2

1-5

With Soldering Iron:

(1) Using desoldering braid, remove the solder from all

pins of the flat pack-IC. When you use solder flux

which is applied to all pins of the flat pack-IC, you

can remove it easily. (Fig. S-1-3)

(2) Lift each lead of the flat pack-IC upward one by

one, using a sharp pin or wire to which solder will

not adhere (iron wire). When heating the pins, use

a fine tip soldering iron or a hot air desoldering

machine. (Fig. S-1-4)

(3) Bottom of the flat pack-IC is fixed with glue to the

CBA; when removing entire flat pack-IC, first apply

soldering iron to center of the flat pack-IC and heat

up. Then remove (glue will be melted). (Fig. S-1-6)

(4) Release the flat pack-IC from the CBA using twee-

zers. (Fig. S-1-6)

With Iron Wire:

(1) Using desoldering braid, remove the solder from all

pins of the flat pack-IC. When you use solder flux

which is applied to all pins of the flat pack-IC, you

can remove it easily. (Fig. S-1-3)

(2) Affix the wire to a workbench or solid mounting

point, as shown in Fig. S-1-5.

(3) While heating the pins using a fine tip soldering

iron or hot air blower, pull up the wire as the solder

melts so as to lift the IC leads from the CBA contact

pads as shown in Fig. S-1-5

(4) Bottom of the flat pack-IC is fixed with glue to the

CBA; when removing entire flat pack-IC, first apply

soldering iron to center of the flat pack-IC and heat

up. Then remove (glue will be melted). (Fig. S-1-6)

(5) Release the flat pack-IC from the CBA using twee-

zers. (Fig. S-1-6)

Note:

When using a soldering iron, care must be taken

to ensure that the flat pack-IC is not being held by

glue. When the flat pack-IC is removed from the

CBA, handle it gently because it may be damaged

if force is applied.

Flat Pack-IC

Desoldering Braid

Soldering Iron

Fig. S-1-3

Fine Tip

Soldering Iron

Sharp

Fig. S-1-4

To Solid

Mounting Point

Soldering Iron

Iron Wire

Hot Air Blower

Fig. S-1-5

Fine Tip

Soldering Iron

CBA

Flat Pack-IC

Tweezers

Fig. S-1-6

1-6

2. Installation

(1) Using desoldering braid, remove the solder from

the foil of each pin of the flat pack-IC on the CBA

so you can install a replacement flat pack-IC more

easily.

(2) The “I” mark on the flat pack-IC indicates pin 1.

(See Fig. S-1-7.) Be sure this mark matches the 1

on the PCB when positioning for installation. Then

presolder the four corners of the flat pack-IC. (See

Fig. S-1-8.)

(3) Solder all pins of the flat pack-IC. Be sure that none

of the pins have solder bridges.

1-3-4 Instructions for Handling

Semi-conductors

Electrostatic breakdown of the semi-conductors may

occur due to a potential difference caused by electro-

static charge during unpacking or repair work.

1. Ground for Human Body

Be sure to wear a grounding band (1MΩ) that is prop-

erly grounded to remove any static electricity that may

be charged on the body.

2. Ground for Workbench

(4) Be sure to place a conductive sheet or copper plate

with proper grounding (1MΩ) on the workbench or

other surface, where the semi-conductors are to be

placed. Because the static electricity charge on

clothing will not escape through the body ground-

ing band, be careful to avoid contacting semi-con-

ductors with your clothing.

Example :

Pin 1 of the Flat Pack-IC

is indicated by a " " mark.

Fig. S-1-7

Presolder

CBA

Flat Pack-IC

Fig. S-1-8

CBA

< Incorrect >

CBA

Grounding Band

Conductive Sheet or

Copper Plate

1MΩ

< Correct >

2-1

2-1 SPECIFICATIONS

GENERAL INFORMATION2

2-2

2-2 COMPARISON OF MODELS

←: Same as on left

ITEM

DV-P735U/P735U(C)/P533U DV-P725U/P325U/P323U

Dimensional 435(W) x 55(H) x 211(D) mm 435(W) x 75(H) x 216(D) mm

Weight 1.8 kg 2.1 kg

Tray Panel Clear Silver

Color Front / Button

Silver/Silver (DV-P735U/P735U(C))

Black/Silver (DV-P533U)

Dark Silver/Silver (DV-P725U)

Black/Silver (DV-P325U)

Silver/Silver (DV-P323U)

Hot Stamp ---

O (DV-P725U)

--- (DV-P325U/P323U)

Ultra Vision Badge ---

O (DV-P725U)

--- (DV-P325U/P323U)

Drive Speed 1x ←

Laser 2 ←

DVD/VCD/SVCD/CD-DA O / --- / --- / O ←

CD-R/CD-RW/DVD-R (Video Format) O / O / O ←

DVD-RAM (VR Format) --- ←

MP3 O ---

OSD languages 3 (English, French, Spanish) ←

Jog Shuttle on Front --- Only switch shuttle

Headphone Jack / Volume --- / ---

O / O (DV-P725U)

--- / --- (DV-P325U/P323U)

PAL Disc NTSC Out --- O

Video Out Mode NTSC/PAL/PAL60 O / --- / --- ←

S-Video / Component / Composite O / O / O ←

Video D/A Converter 10bit ←

Black Level Select O ←

Picture Control --- ←

Progressive Out

O (DV-P735U/P735U(C))

--- (DV-P533U)

O (DV-P725U)

--- (DV-P325U/P323U)

Audio D/A Converter 192kHz / 24bit ←

Digital Audio Out Optical / Coaxial --- / O O / O

Dolby Digital 5.1 ch Decode --- ←

DTS Digital Out --- O

Virtual Surround O

O (DV-P725U/P325U)

--- (DV-P323U)

Dynamic Range Compression (Dolby

Digital)

O ←

DVD Audio --- ←

Power on sound --- ←

Search Speed

2 to 100 (FORWARD/REWIND)

(DVD: 2, 8, 50, 100/CD: 16)

2 to 60 (FORWARD/REWIND)

(DVD: 2, 8, 30, 60/CD: 16)

Slow Speed 1/16, 1/8, 1/2 (FORWARD/REWIND) 1/16, 1/8, 1/2 (FORWARD only)

IP Search (Smooth 2x Play) O ←

2x Play with Audio --- ←

Step Forward / Reverse O / O O / ---

Still Picture Select (Frame/Field) Auto Only ←

PPEARANC

ENERA

IDE

UDI

RICK PLA

2-3

ITEM

DV-P735U/P735U(C)/P533U DV-P725U/P325U/P323U

Disc Navigation

O (DV-P735U/P735U(C))

--- (DV-P533U)

---

DVD Zoom x2 / x4 / x16 O / O / --- ←

Program and Random Play of DVD /

VCD

--- ←

A-B Repeat O ←

Repeat O ←

Last Play O ←

Closed Caption for NTSC DVD O ←

Front Panel Display Dimmer O ←

Screen Saver O ←

Auto Power Off O ←

Jog Shuttle on Remote --- ←

TV Control

O (DV-P735U/P735U(C))

--- (DV-P533U)

FEATURES

REMOTE

CONTROLLER

2-4

ANALOG AUDIO OUT

DIGTAL AUDIO OUT

COAXIAL

S-VIDEO

OUT

VIDEO

OUT

RCB/PB

CR/PR

COMPONENT

VIDEO OUT

I P

PROGRESSIVE

13 151211910 14

REAR VIEW

y/I POWER/

STANDBY

H/E

SKIP/FR

D/G

FF/SKIP

OPEN/CLOSE

PLAY

STOP

1 6

82 3 4 5

FRONT PANEL

1. y/I (POWER/STANDBY)

to switch the player to ON or OFF

(As to the indication of the Operate switch, “I” indicates

ON and “y” indicates electrical power STANDBY)

2. SKIP/FR

goes to previous chapter or track during playback; press

and hold for 1.5 seconds for a reverse search

3. PLAY

to start or resume disc playback

4. FF/SKIP

goes to next chapter or track during playback; press and

hold for 1.5 seconds for a forward search

5. STOP

to stop playback

6. OPEN/CLOSE

to open/close the disc tray

7. Disc tray

8. Display

9. MAIN (AC Power Cord)

connect to a standard AC outlet

10. COAXIAL (Digital audio out)

connect to AUDIO inputs of a digital (coaxial) audio

equipment

11. AUDIO OUT (Left/Right)

connect to AUDIO inputs of an amplifier, receiver or

stereo system

12. VIDEO OUT

connect to the Video Input of a TV.

13. COMPONENT VIDEO OUT

connect to a TV with Component video in jacks.

14. S-VIDEO OUT

connect to a TV with S-Video inputs

15. INTERLACE/PROGRESSIVE SCAN SELECTOR

to select interlace or progressive scanning

Caution: Do not touch the inner pins of the jacks on the

rear panel. Electrostatic discharge may cause permanent

damage to the player.

2-3 OPERATING CONTROLS AND FUNCTIONS

[ DV-P735U/P735(C) ]

2-5

REMOTE CONTROL

+10

MODE

OPEN

ZOOM

DISPLAY

AUDIO

TOP MENU

SETUP

PLAY

SKIP

A-B REPEAT

REPEAT

CLEAR

SUBTITLE

MODE

ANGLE

DISC

NAVIGATION

RETURN

STOP

TV POWER

VIDEO/TV

SURROUND

PAUSE/STEP

VOL

ENTER

1. SURROUND

Press to activate the virtual sound.

(POWER/STANDBY)

Press to turn the power on and off.

(As to the indication of the Operate switch, "I" shows

ON and "

/I" shows electrical power stand-by.)

3. A-B REPEAT

Repeats playback of a selected section.

4. REPEAT

Repeats playback of the current disc, title, chapter or

track.

5. MODE

Activates program playback or random playback mode

when playing CDs or MP3. Sets Black level and virtual

surround.

6. ZOOM

Enlarges part of a DVD-reproduced image.

7. CLEAR

Press to reset the setting.

8. ANGLE

Press to change the camera angle to see the sequence

being played back from a different angle.

9. SUBTITLE

Press to select the desired subtitle language.

10. MENU

Press to display the menu of the Disc.

11. Arrow Buttons (

)

Move the cursor and determines its position.

12. ENTER

Press to accept a setting.

13. RETURN

Returns to the previous operation.

14. SKIP

Press to skip Chapters or Tracks.

15. STOP

Press to stop the disc motion.

16.

Press to view the DVD picture in fast reverse motion or

to (reverse playback of an Audio CD.

17. TV POWER

To exclusively turn ON/OFF the TV.

18. VIDEO/TV

Press to select the external input mode or TV mode of

the TV.

19. TV VOL ( / )

Press to exclusively control the TV volume.

20. TV CH

Press to exclusively control the TV channels.

21. PAUSE/STEP

Press to pause Disc playback. Press repeatedly to

advance the DVD picture step by step (or one frame at

a time).

22.

Press to fast forward the Disc. Press PAUSE/STEP,

then press this button to begin slow motion playback.

Press this button repeatedly to change the forward

speed of slow motion.

23. PLAY

Press to begin playback.

24. DISC NAVIGATION

Press to enter the setup mode.

25. SETUP

Press to display the first scenes of each chapter of the

title being played.

26. TOP MENU

Press to call up the title menu.

27. DISPLAY

Press to access or remove the display screen during

DVD or Audio CD playback.

28. AUDIO

Press to select a desired audio language or sound

mode.

29. Numerical Buttons

Press to directly select a Track (Audio CD) for playback.

30. OPEN/CLOSE

Press to open or close the disc loading tray.

31. SEARCH MODE

Press to access or remove the Search display, which

allows you to go directly to a specific

Title/Chapter/Track/Time

2-6

Display

Displays During Operation

Stays on when the inserted

disc is being played back.

Lights up when a CD is

inserted into the tray.

Lights up when a DVD

is inserted into the tray.

Lights up when the

inserted disc comes

to a pause.

Stays on when repeat chapter function is on.

Stays on when repeat track function is on.

Stays on when

the A-B repeat

function is on.

Stays on when

the repeat function is on.

Stays on when repeat

title function is on.

Displays how long a current title or track has been

played back. When a chapter or track has switched,

the number of a new title, chapter or track is displayed.

Power on

No disc inserted/can not read

Tray open

Tray closed

Loading the Disc

When a disc is being

Play back

Power off

2-7

[ DV-P533U ]

ANALOG AUDIO OUT

DIGTAL AUDIO OUT

COAXIAL

S-VIDEO

OUT

VIDEO

OUT

RCB/PB

CR/PR

COMPONENT

VIDEO OUT

I P

PROGRESSIVE

13 151211910 14

REAR VIEW

y/I POWER/

STANDBY

H/E

SKIP/FR

D/G

FF/SKIP

OPEN/CLOSE

PLAY

STOP

1 6

82 3 4 5

FRONT PANEL

REMOTE CONTROL

RETURN

ZOOM

MODE

SKIP

PAUSE/STEP

REPEAT

A-B REPEAT

ANGLE

AUDIO

SUBTITLE

CLEAR

TOP MENU

STOP

PLAY

SETUP

ENTER

OPEN/CLOSESEARCH MODE

DISPLAY

123

456

789

0 +10

1. y/I (POWER/STANDBY)

to switch the player to ON or OFF

(As to the indication of the Operate switch, “I” indicates

ON and “y” indicates electrical power STANDBY)

2. SKIP/FR

goes to previous chapter or track during playback; press

and hold for 1.5 seconds for a reverse search

3. PLAY

to start or resume disc playback

4. FF/SKIP

goes to next chapter or track during playback; press and

hold for 1.5 seconds for a forward search

5. STOP

to stop playback

6. OPEN/CLOSE

to open/close the disc tray

7. Disc tray

8. Display

9. MAIN (AC Power Cord)

connect to a standard AC outlet

10. COAXIAL (Digital audio out)

connect to AUDIO inputs of a digital (coaxial) audio

equipment

11. AUDIO OUT (Left/Right)

connect to AUDIO inputs of an amplifier, receiver or

stereo system

12. VIDEO OUT

connect to the Video Input of a TV.

13. COMPONENT VIDEO OUT

connect to a TV with Component video in jacks.

14. S-VIDEO OUT

connect to a TV with S-Video inputs

15. INTERLACE/PROGRESSIVE SCAN SELECTOR

to select interlace or progressive scanning

Caution: Do not touch the inner pins of the jacks on the

rear panel. Electrostatic discharge may cause permanent

damage to the player.

9. PAUSE/STEP

pause playback temporarily / frame-by-frame playback

10.

to view DVD picture in fast reverse motion

11. PLAY

to start a DVD disc playback

12. SETUP

to access or remove the DVD setup menu

13. MODE

to set up programmed or random playback (Audio CD)

to set the black level and virtual surround during DVD

playback

14. ZOOM

enlarge DVD video image

15. TOP MENU

to display title menu of a disc

16. ENTER

acknowledge menu selection

17. RETURN

to return previous or remove setup menu

18. Arrow (sB

)

(left/right/up/down) select an item in the menu

19. MENU

to display the menu of the DVD disc

20. STOP

to stop a DVD disc playback

21.

to view DVD picture in fast forward motion

22. SKIP H,G

to skip chapter/tracks

23. 0-9 numerical buttons

select numbered items in a menu

+10

use this button to enter number 10 and above

24. OPEN/CLOSE

to open/close the disc tray

25. SEARCH MODE

to locate a desired point

1. DISPLAY

to access or remove the display screen during DVD or

Audio CD playback

2. y/I (POWER/STANDBY)

switch DVD player ON or OFF

3. AUDIO

to choose audio languages or sound modes

4. SUBTITLE

subtitle language DVD selector

5. ANGLE

select DVD camera angle

6. REPEAT

repeat chapter, track, title, all.

7. A-B REPEAT

repeat a specific segment

8. CLEAR

to reset the setting

2-8

Display

Displays During Operation

Stays on when the inserted

disc is being played back.

Lights up when a CD is

inserted into the tray.

Lights up when a DVD

is inserted into the tray.

Lights up when the

inserted disc comes

to a pause.

Stays on when repeat chapter function is on.

Stays on when repeat track function is on.

Stays on when

the A-B repeat

function is on.

Stays on when

the repeat function is on.

Stays on when repeat

title function is on.

Displays how long a current title or track has been

played back. When a chapter or track has switched,

the number of a new title, chapter or track is displayed.

Power on

No disc inserted

Tray open

Tray closed

Loading the Disc

When a disc is being

Play back

Power off

3-1

MAINTENANCE AND INSPECTION3

FLOW CHART NO.1

The power cannot be turned on.

FLOW CHART NO.2

The fuse blows out.

After servicing, replace the fuse.

Is the fuse normal?

Is normal state restored when once unplugged

power cord is plugged again after several seconds?

Is the EV+9V line voltage normal?

Check each rectifying circuit of the secondary circuit

and

service it if defective.

Check the presence that the primary component

is leaking or shorted and service it if defective.

See FLOW CHART No.2 <The fuse blows out.>

Check if there is any leak or short-circuiting on the

primary circuit component,

and

service it if

defective. (Q1001, Q1003, T1001, D1001, D1002,

D1004, D1005, D1011, C1003, C1005)

Check the presence that the rectifying diode or

circuit is shorted in each rectifying circuit of

secondary side, and service it if defective.

Ye s

FLOW CHART NO.3

When the output voltage fluctuates.

Ye s

FLOW CHART NO.4

When buzz sound can be heard in the vicinity of power circuit.

Check if there is any short-circuit on the rectifying diode and the circuit in each rectifying circuit of the secondary side

and service it if defective.

(D1003, D1006, D1008, D1016, D1030, IC1002, Q1002, Q1004, Q1011)

Does the photo coupler circuit on the secondary

side operate normally?

Check IC1001, D1012, D1024 and their periphery,

and service it if defective.

Check IC1001, IC1006, D1015, D1048 and their

periphery, and service it if defective.

FLOW CHART NO.5

-FL is not outputted.

Is -24V voltage supplied to the anode of D1003?

Check D1003 and periphery circuit, and service it

if defective.

Check if there is any leak or short-circuit

on the loaded circuit, and service it if defective.

Ye s

3-1 TROUBLESHOOTING

Troubleshooting is how to service for the specifying malfunction or poor parts.

Detect malfunction or poor parts and service as the following charts.

3-2

FLOW CHART NO.7

P-ON+5V is not outputted. (P-ON+9V is outputted normally.)

Is the "H" pulse inputted into the base of Q1004?

Replace Q1004.

Check R1068 and D1046, and service it if defective

Ye s

FLOW CHART NO.8

P-ON+3.3V (EV+3.3V) is not outputted. (P-ON+9V is outputted normally.)

Is 3.3V voltage supplied to the collector of Q1011?

Replace Q1011 and R1067.

Check D1008, D1015, C1007, C1038 and the

periphery circuit, and service it if defective.

Ye s

FLOW CHART NO.9

EV+5V is not outputted.

Is EV+9V outputted normally?

Check D1047 and the periphery circuit, and

service it if defective.

Refer to "FLOW CHART NO.6"

<P-ON+9V (EV+9V) is not outputted.>

Ye s

Is approximately 2.5V voltage supplied to Pin(1)

of IC1002?

FLOW CHART NO.10

EV+1.5V is not outputted.

Replace IC1002.

Check D1006,C1014,C1050, and their periphery,

and service it if detective.

FLOW CHART NO.6

P-ON+9V (EV+9V) is not outputted.

Is 9V voltage supplied to the emitter of Q1002?

Is the voltage of base on Q1002 lower than the

voltage of emitter on Q1002 when turning the power on?

Replace Q1002.

Check D1030, D1048, C1035, C1048 and the

periphery circuit, and service it if defective.

Check Q1016 and PWRCON line and service it if

defective.

Ye s

3-3

FLOW CHART NO.13

No operation is possible from the remote control unit.

Operation is possible from the DVD, but no

operation is possible from the remote control unit.

Replace the infrared remote control receiver (RM2001)

Or replace the remote control unit.

Check the line between Pin(1) of the infrared

remote control receiver (RM2001) and Pin(22) of

CN1001, and service it if detective.

Is the "L" pulse sent out Pin(1) terminal of receiver

(RM2001) when the infrared remote control is activated?

Is the "L" pulse signal supplied to the Pin(22) of

CN1001?

Replace DVD Main CBA.

Ye s

Is 5V voltage supplied to the Pin(3) terminal of

the infrared remote control receiver (RM2001)?

Ye s

Check EV+5V line and service it if detective.

Ye s

FLOW CHART NO.12

The key operation is not functioning.

Are the contact point and the installation state of the

key switches (SW2002, 2003, 2005-2008) normal?

When pressing each switches (SW2002-2003,

2005-2008), do the voltage of each pin

of IC2001 (shown below) switch to 75mV from

6mV?

SW2002, 2006, 2008 : IC2001 3PIN

SW2003, 2005, 2007 : IC2001 4PIN

Check the switches (SW2002, 2003, 2005-2008)

and their periphery, and service it if detective.

Re-install the switches (SW2002, 2003,

2005-2008) correctly or replace the poor switch.

Replace IC2001.

Ye s

FLOW CHART NO.11

The fluorescent display tube does not light up.

Is 3.3V voltage supplied to Pin(6) and

Pin(24) of IC2001?

Is the voltage of approximately -24V to -28V

supplied to Pin(15) of IC2001?

Is there 500kHz oscillation at Pin(26) of IC2001?

Are the filament voltage supplied between

Pins(1, 2) and Pins(34, 35) of the fluorescent

display tube? And the negative voltage applied

between these pins and GND?

Replace the fluorescent display tube.

Check the EV+3.3V line and service it if detective.

Check the -FL (-28V) line and service it if detective

Check R2015, IC2001 and their periphery, and

service it if detective.

Check D1016, D1017, R1079, C1018, and their

periphery, and service it if detective.

3-4

FLOW CHART NO.16

[No Disc] indicated. (When the focus error occurs.)

Replace the DVD Main CBA.

No improvement can be found.

Original DVD Main CBA is poor.

Replace the DVD Mecha.

Ye s

FLOW CHART NO.17

[No Disc] indicated. (When the focus servo is not functioning.)

FLOW CHART NO.18

[No Disc] indicated. (When the laser beam does not light up.)

Replace the DVD Main CBA.

Replace the DVD Mecha.

Ye s

Replace the DVD Main CBA.

Replace the DVD Mecha.

Ye s

No improvement can be found.

Original DVD Main CBA is poor.

No improvement can be found.

Original DVD Main CBA is poor.

Ye s

FLOW CHART NO.15

The disc tray cannot be opened and closed.

Replace the DVD Main CBA.

Original DVD Main CBA is poor.

Replace the DVD Mecha.

No improvement can be found.

Ye s

FLOW CHART NO.14

The disc tray cannot be opened and closed. (It can be done using the remote control unit.)

Does the voltage of Pin(4) on IC2001 become 75mV

when pressing "OPEN/CLOSE" button on the unit?

Refer to "FLOW CHART NO.15" <The disc tray

cannot be opened and closed.>

Replace the "OPEN/CLOSE" button (SW2005).

Page is loading ...

Hitachi DV-P533U User manual

Brand: Hitachi

Model: DV-P533U

Category: DVD players

Type: User manual

This manual is also suitable for

Download PDF

report

Hitachi DV-P533U User manual

This manual is also suitable for

Hitachi DV-P533U User manual

Related papers

Other documents