König SAT-SDFTA11BL User manual

Brand: König

Model: SAT-SDFTA11BL

Category: TV set-top boxes

Type: User manual

The König SAT-SDFTA11BL is an advanced satellite receiver equipped with numerous features to enhance your TV viewing experience. With its high-quality video and audio output, you can enjoy crystal-clear and immersive entertainment. Fully MPEG-2 and DVB compliant, it supports up to 4000 channels, providing you with a wide range of programming options.

SDFTA11

FREE TO AIR

SATELLITE RECEIVER

MANUAL

ANLEITUNG

MODE D’EMPLOI

GEBRUIKSAANWIJZING

MANUALE

MANUAL DE USO

HASZNÁLATI ÚTMUTATÓ

KÄYTTÖOHJE

BRUKSANVISNING

NÁVOD K POUŽITÍ

INTRODUCTION

Features:

This user manual covers the installation of the SDFTA11 satellite receiver and the

necessary steps to operate various features. This manual also explains special features

available only in this receiver and will allow you to get full advantage of these features.

This receiver offers:

 High quality Video & Audio

 Fully MPEG-2, DVB compliant

 4000 channels

 Electronic Program Guide (EPG)

 Teletext

 Subtitling

 256 colours On-Screen-Display

 Timer function

Contents of the packaging:

After purchasing the receiver, unpack it and check to make sure that all of the following

Items are included in the packaging:

 SDFTA11 Receiver

 Remote control

 2x AAA batteries

Remarks to the installation, use and care of the receiver:

Place the product in a well-ventilated area.

Don’t install in the cold or under direct

sunlight.

Leave a minimum 10cm gap all around the

product.

Don’t disassemble, repair, or reorganize

the product.

Don’t place objects on top of the product. Don’t place cups that hold water or other

liquids on top of the product.

English Deutsch Français Nederlands

Italiano Español Magyar Suomi Svenska Česky

Remote Control:

: Turns power ON/OFF

: Mute sound

TV/Radio: Switches between TV and Radio

0~9: Numeric keys

: Switches back to previous channel

Menu: Enters menu

EXIT: Exits menu or function

OK/LIST: Confirms action or shows channel list

FAV: Show favourite list

INFO: Show info about current channel/program

PR+/PR-: Change channels or move to higher/lower item

Adjust volume or move left/right in the menu

EPG: Show the Electronic Program Guide

: Show the Audio window.

SAT: Show the satellite list

A~Z: Show the find window

: Moves up/down a page in list

: Show multi screen

SLEEP: Enter sleep mode

PAUSE: Pauses picture

ZOOM: Enter zoom mode

TV/AV: Switch TV/AV mode

: Teletext/subtitle

English Deutsch Français Nederlands

Italiano Español Magyar Suomi Svenska Česky

CONNECTIONS

Connecting TV, auxiliary and antenna to the receiver.

 Connect the TV to the receiver (TV OUT) using a scart cable

 Connect a video recorder or DVD-recorder to the receiver (Video out) using a

scart cable

 Connect the (active) antenna to the receiver (RF IN)

 Connect the TV to the receiver (RF OUT)

 Connect a stereoset with coaxial and/or left/right input to the output on the

receiver

English Deutsch Français Nederlands

Italiano Español Magyar Suomi Svenska Česky

INSTALLATION

Installation menu

1. Press OK key or ▲ key to pop up the "Input Password" dialogue. You can not enter into

the menu unless the correct password is inputted. The default password is "0000". (The

password may be turned off in the parental lock option in system setup.)

2. Press ▲/▼ keys to move the cursor up or down.

3. Press EXIT key to exit.

2.1 Antenna Connection

Press keys to select between Motor Antenna and Fixed Antenna.

2.2 Satellite List

1. Press ▲/▼ keys to choose the satellite. Press OK key to select and mark, press OK key

again to cancel the selection and the mark.

2. If there is no satellite, the red colour and blue colour keys will be invalid.

3. Press red colour key to pop up the Edit Satellite window. Press ▲/▼ keys to move

cursor up or down.

Name: User numeric keys to change the name of the satellite, please refer to the Edit

Channel Name.

Longitude: You can press keys to switch between east longitude and west longitude. After

pressing OK key, you can use numeric keys to edit the longitude, press EXIT key or the

▲/▼ keys to exit editing mode. The range of the longitude is from 1 to 180 degrees. If

beyond this range, system will inform you "out of range" when you press yellow colour key

on the RCU.

After setting, press yellow colour key to save and exit, while press blue colour key to exit

without saving.

4. Press green colour key to pop up the Add Satellite window. Since the same operation

as the above Edit Satellite window, here we don't explain any more.

5. Press blue colour key to pop up the dialogue "Are you sure to delete?". Select Yes

button and press OK key to delete the selected satellite. You can cancel this operation by

pressing OK key at the NO button.

2.3 Antenna Setup

Part A: Fixed

Suppose that you have selected Fixed Antenna in the Antenna Connection window.

1. Satellite: All selected satellites in the satellite list are displayed in this item. Press keys

to select the satellite in circle. Or press OK key to pop up the dropdown list, then select the

desired satellite in the list and press OK key to confirm.

2. LNB Freq, Transponder, DiSEqC1.0, DiSEqC1.1: The same operation as the

above.

3. 22K, 0/12V, Toneburst, LNB Power: You can press keys to select in circle.

English Deutsch Français Nederlands

Italiano Español Magyar Suomi Svenska Česky

Part B: Moter

Suppose that you have selected Moter Antenna in the Antenna Connection window.

1. LNB Type: Select the proper LNB type.

2. Motor Type: Select between DiSEqC1.2 and USALS. If you select DiSEqC1.2, the

following Local Longitude and Local Latitude items will turn grey.

3. Delete All: Press OK key to pop up the dialogue "Are you sure to clear set satellite

position of this tuner?". Press OK key at the Yes button to clear all the memories about

the position of the satellites that has connected to the current turner.

4. Motor Setting: Press OK key to the Motor Setting window.

Satellite: Press keys to select the satellite in circle. Or press OK key to pop up the drop-

down list, then select the desired satellite in the list and press OK key to confirm.

Transponder: The same operation as the above.

Position No., & Save: The range is from 0 to 63. "0" delegates the original position.

You can select the proper value when you has rotated the antenna.

Go to X: Press OK key to pop up the drop-down list, select the proper position

(reference or from 1to 63) to realize the selected position.

West <Save> East: Press key to turn west, while press key to turn east. Press OK key to

pop up the dialogue "Are you sure to change this satellite's position?". Press OK key at the

Yes button to save the current position, or press OK key at the No button to cancel the

operation.

Recalculation: Press OK key to pop up the dialogue "Are you sure to change this

satellite's position?". Press OK key at the Yes button to recalculation.

5. Limit Setup: Press OK key to pop up the Limit Setup window.

Limit Setup: Press keys to switch among Disable Limit, East Limit and West Limit.

Limit Setup: Move cursor to the Limit Setup button. You can press key to turn west, or

press key to turn east.

Go to Reference: Press OK key to go to reference. If you select Disable Limit in the

above Limit Setup item, this button will turn grey.

6. If select USALS, Delete All item will turn grey.

Local Longitude, Local Latitude: Press keys to switch between West and East, or press

keys to switch between North and South. Press OK key to enter into the editing mode. Use

numeric keys (0-9) to input the longitude or latitude, press MENU key or EXIT key to exit.

The range of the longitude is from 0 to 180, while the range of the latitude is from 0 to 90. If

the inputted value is not in this range, system will pop up a dialogue "Our of Range" when

exit from this window. You can press OK key to close this dialogue.

7. Motor Setting: Press OK key to enter into the Motor setting window.

Satellite, Transponder: Press keys to select satellite or transponder, or press OK key to

pop up the drop-down list and select in the list.

English Deutsch Français Nederlands

Italiano Español Magyar Suomi Svenska Česky

2.4 Single Satellite Search

1. Satellite :

Press keys to select the satellite in circle. Or press OK key to pop up the drop-down list,

then select the desired satellite in the list and press OK key to confirm.

2. FTA Only: Press keys to select between Yes and No.

3. Scan Channel: Press keys to select among TV+Radio, TV Channel, Radio.

4. Network Search: Select between No and Yes. This item turns grey when Auto Scan is

selected in the following Scan mode item.

5. Scan Mode: Press keys to select between Auto Scan and Blind Scan. Auto Scan is

searching the preset transponders, while Blind Scan is to search the whole frequency

band.

6. Search: Press OK key to start searching.

2.5 Multi Satellite Search

From the Multi Satellite Search window, you can search several satellites at the one

time.

1. Satellite: All selected satellites in the satellite list window are displayed on the

down part. You can press keys to switch among them.

2. FTA Only: Press keys to select between Yes and No.

3. Scan Channel: Press keys to select among TV+Radio, TV Channel, Radio.

4. Network Search: Select between No and Yes. This item turns grey when Auto

Scan is selected in the following Scan mode item.

5. Scan Mode: Press keys to select between Auto Scan and Blind Scan. Auto Scan is

searching the preset transponders, while Blind Scan is to search the whole frequency

band.

6. Search: Press OK key to start searching.

2.6 TP List

1. Press ◄/► keys to select the proper satellite.

2. Press red colour key to pop up the Edit TP window.

Frequency, Symbol rate: Press keys to add or reduce by step one. Or press numeric

keys (0-9) to input the desired value. The range of the frequency is 3000-13450, while the

range of the symbol rate is 1000~45000. The inputted value is beyond this range, the value

will return to the original value.

Polarity: Press keys to switch between Vertical and Horizontal.

3. Press green colour key to pop up the Add TP window. Since the same operation as the

above Edit TP window, here we don't explain any more.

4. Press yellow colour key to pop up dialogue " Are you sure to delete?". Press OK key at

the Yes button to delete the selected TP, or press EXIT key to cancel the operation.

5. Press blue colour key to pop up the TP Search window.

FTA only, Scan Channel, Network Search: Press keys to select the proper option.

Press OK key at the OK button to start searching.

English Deutsch Français Nederlands

Italiano Español Magyar Suomi Svenska Česky

CHANNEL MANAGER

1. Press OK key or ▲ key in the Edit Channel menu to pop up the "Input Password"

dialogue. You can not enter into the menu unless the correct password is inputted. The

default password is "0000".

2. Press ▲/▼ keys to move the cursor up or down.

3. Press EXIT key to exit.

TV Channel list

1. Press ◄/►keys to select satellite.

2. Press ▲/▼ keys to select the program that you want to play and then press OK key to

view it in the small window.

3. Press FAV key to select the favourites manager. Select the program and press OK key

to pop up the favourite group list. In the list, select the group that you want to add into and

press OK key, and then you will find the favorite mark is displayed at the right side of the

selected program. Press FAV key again to exit from the fav mode, and you will find the

FAV button return to the origin position.

4. Press red colour key to select the Lock manager. Select the program and press OK key

to mark this program with the Lock mark. You can cancel this mark by pressing OK key

once more. Press red colour key again to exit from the lock mode, and you will find the

Lock button return to the origin position.

5. Press green colour key to select the Skip manager. Select the program and press OK

key to mark this program with the skip mark. You can cancel this mark by pressing OK key

once more. Press green colour key again to exit from the skip mode, and you will find the

Skip button return to the origin position.

6. Press yellow colour key to select the Move manager. Select the program and press OK

key to mark this program with the move mark. Press PR+, PR- keys to move the cursor to

the position where you want to locate and press OK key to confirm. Press yellow colour

key again to exit from the yellow mode, and you will find the yellow button return to the

origin position.

7. Press blue colour key to enter into the Edit channel window.

a . Sort (red colour key) Press red colour key to pop up the Sort dropdown

list.

Name(A-Z): The ascending order, omitting the $ character, the number is ahead, then the

capital letter, at last the lowercase.

Name (Z-A): The opposite order of the above Name (A-Z).

Free/Scrabmle:: All FTA programs are listed ahead, while all scrambled programs are

listed last.

Lock: all locked programs are listed at the last.

English Deutsch Français Nederlands

Italiano Español Magyar Suomi Svenska Česky

b. Edit (green colour key)

Press green colour key to select the Edit menu. Select the program and press OK key to

pop up the Rename window. In Rename window, press red colour key to switch between

capital letter and lower letter; press green colour key to delete the character on the cursor;

press keys to move the cursor left or right; press numeric keys (0-9) to input the character,

please refer to the down table. Press yellow colour key to save and exit, or press blue key

to cancel and exit.

Numeric keys Press numeric key repeatedly

1 .,*?!@1

2 ABC2

3 DEF3

4 GHI4

5 JKL5

6 MNO6

7 PQRS7

8 TUV8

9 WXYZ9

0 [space]_-0

If the name is empty, system will pop up a dialogue informing "Name" once yellow colour

key is pressed. Press OK key to close this dialogue.

c. Edit (blue colour key)

In Edit Channel window, press blue colour key to select the Delete menu. Select the

program and press OK key to mark this program with the deletion mark. You can cancel

this mark by pressing OK key again. Press EXIT key to pop up the dialogue "Are you sure

to save?". Select Yes button and press OK key to save, or select NO button and press OK

key to exit without saving.

1.2 Radio Channel List

Since the same operation as TV Channel List, here we don't explain any more.

1.3 Delete All

Move cursor to the Delete All item, and press OK Key to pop up the dialogue "Warning! Do

you really want to delete all channel?". Press EXIT key to pop up the dialogue "Are you

sure to save?". Select Yes button and press OK key to save, or select NO button and press

OK key to exit without saving.

English Deutsch Français Nederlands

Italiano Español Magyar Suomi Svenska Česky

SYSTEM SETUP

3.1 Language

1. Press OK key to enter into the Language window. Press keys to select the language in

circle, while press ▲/▼ keys to move the cursor up or down in circle.

2. Press MENU key or EXIT key to save and exit.

3. The types of the language, pleaser refer to the configuration of the customer.

3.2 TV

Press ▲/▼ key to move the cursor up or down, while press keys to change the setting and

the setting will take effect immediately.

1. Display Mode: Select among Auto,PAL, PAL-M, PAL-N, NTSC.

2. Aspect Mode: Select among 4:3LetterBox, 4:3PanScan, 16:9.

3. Video Output: Select between RGB and CVBS.If you select the mode of RGB,the

VCR Loopthrough will turn grey below.

4. VCR Loopthrough: Select among STB Master,VCR Master.

3.3 Local Time Setting

1. Summer Time: Select between ON and OFF. "OFF" delegates the normal time. If

select ON, time will add one hour.

2. GMT Offset: When select "ON" in GMT Usage item, system will get the date and time

information from the screen automatically. Date and Time two items will turn grey.

Select the proper option in the GMT Offset

item. The default setting is GMT ON.

3.Date, Time: When select "OFF" in GMT Usage, Date and Time are shown, while GMT

Usage turns grey. Use numeric keys to input the desired value.

After setting, press MENU key or EXIT key to exit and save. If the value is invalid,

system will inform "Invalid input! Continue to edit?". Press OK key at the Yes button

to continue the modification, or press OK key at the No button to exit without saving.

3.4 Timer Setting

If there is no program, you can not enter into this window. There are 8 timers that can be

set. Select Timer up or down, and press OK key to enter into the setting window.

1. Timer mode: The default mode is off. You can set the timer once, daily, weekly,

monthly and yearly.

2. Timer Service: Select between Channel and Message. If Channel is selected, the

Wakeup Channel is displayed in the following item. If Message is selected, the

Wakeup Message is displayed in the following item. In wakeup message, you can

select among Birthday, Anniversary, General. At the same time the duration item turns

grey.

3. Wakeup Date, On Time: Use numeric keys to input the valid date.

Duration: Set the gap time. After waking up, system will power off automatically

after the duration time.

Press MENU or EXIT key to save and exit.

English Deutsch Français Nederlands

Italiano Español Magyar Suomi Svenska Česky

3.5 Parental Lock

Before entering the Parental Lock window, you need to enter the correct password.

The default password is "0000".

1. Menu Lock: Press keys to select between Off and On. If select "On" , you can not enter

into the most windows before entering the password.

2. Channel Lock: Press keys to select between Off and On. The default value is Off.

3.5 Parental Lock: If select "On", you can not view the locked channel set in Chanel List

Edit window until you have inputted the correct password.

3. New Password: User numeric key (0-9) to input the new password.

4. Confirm Password: Input the new password once again. Confirm password must be

the same as the New password. System will inform you "Change password

successfully!" while they are the same, or inform you to input the password of Confirm

password once again when they are not the same.

3.6 OSD Setting

1. Subtitle Display: Press keys to select between On and Off.

2. OSD Timeout: Press keys to select from 1 to 10 by step1. The default value is 5.

3. OSD Transparency: Press keys to select among Off, 10%, 20%, 30%, 40%. The

default option is Off.

Press MENU or EXIT key to save and exit.

3.7 Favourite

There are 32 favourites group listed in this window. Press ▲/▼ keys to select one

and press OK key to the Rename window. Since this is the same operation as the Add

Satellite window, here we don't explain any more.

3.8 Other

1. LNB Power: Select between Off and On.

2. Channel Play Type: Select among All, Free, Scramble.

3. Channel Change: Select between Freeze and Black screen.

4. Beeper: Select between Off and On.

English Deutsch Français Nederlands

Italiano Español Magyar Suomi Svenska Česky

TOOLS

1. Press OK key or key to pop up the "Input Password" dialogue. You can not enter into the

menu unless the correct password is inputted. The default password is 0000.

2. Press ▲/▼ keys to move the cursor up or down.

3. Press EXIT key to exit.

4.1 Information

Press OK key to enter the Information window.

4.2 Factory Setting

Press OK key to enter into the Factory Setting window. Select Yes button and press OK

key to return to the factory setting. All searched channels and set information will be

erased. Select No button and press OK key to cancel this operation, or press MENU or

EXIT key to cancel and exit.

4.3 SatcoDX Auto Programing

Press OK key at the Start button to start receiving date from RS232 for 10 seconds.

4.4 Upgrade By RS232

1. Press keys to select among the options. The default option is allcode.

2. Press OK key at the Start button to start checking serial port.

Game

1. Press OK key or ▲ key to enter into the game menu.

2. Press ▲/▼ keys to move the cursor up or down.

3. Press EXIT key to exit.

4. Select the game that you want to play and press OK key to enter into the window.

English Deutsch Français Nederlands

Italiano Español Magyar Suomi Svenska Česky

OPERATION

6.1 Info

Press INFO key to pop up the Info bar.

Press INFO key again to pop up the program guide of the current program. You can press

◄/► keys to know the program guide of the future 16 days.

6.2 EPG

Press EPG key to enter into the EPG window.

1. Press ▲/▼, ◄/► keys to select up or down, left or right.

2. Press the red colour key to pop up the Time Bar window. Press ▲/▼ keys to select up

or down, while press ◄/► keys to select left or right in the time bar.

← : Press OK key at this button to return to the EPG window.

↑ : Press OK key at this button to move the cursor to the current time line.

◄/►: Press OK key to push the time forward or backward by half an hour.

◄◄/►►: Press OK key to push the time forward or backward by half an hour.

◄◄◄/►►►: Press OK key to push the time forward or backward by a day.

3. Detail Information: In the EPG window, press ▲/▼, ◄/► keys to select the

channel and program, and press OK key to know the detail information of the current

program.

4. Press the green colour key to enter the Timer window. You can add the current

program to the Timer.

6.3 Find

Press A-Z key on to pop up the Find window. User numeric keys to enter into the character

and use the colour keys to realized the corresponding operation.

6.4 Number

Use the numeric keys (0-9) to input the number of the desired channel. If the inputted

number is beyond the valid channel number, the system will show "No such a channel".

Press OK key to close this message.

6.5 TV/RADIO

In normal mode, press TV/RADIO key to switch between TV mode and Radio mode.

6.6 Up/Down (Channel Change)

Press ▲/▼ keys to change the channel up or down. When in "all satellites" group,

you can select channel in all searched channels. If in a specific satellite, you can only

select a channel in the satellite group.

English Deutsch Français Nederlands

Italiano Español Magyar Suomi Svenska Česky

6.7 Left/Right (Volume+/-)

Press the ◄/► keys to change the volume. Press the ◄ keys to decrease the volume by

1 step, while press ► key to increase the volume by step1.

6.8 Mute

Press the key to mute the sound. You can press the key once again, or press ◄/►

keys, to restore the volume.

6.9 Pause

During the viewing, you can press PAUSE key to stop the picture while the volume

continues. You can play the picture by pressing PAUSE key once again.

6.10 OK

1. During the viewing or listening, press OK key to pop up the TV program list or the

Radio program list.

2. Press the ▲/▼ keys to select the channel up or down, and then press OK key to play

this channel in full-screen.

3. Press the ◄/► keys to select the satellite.

4. Press MENU or EXIT key to close this window.

6.11 Audio

1. Press the key to enter the Audio window.

2. Press the ◄/► keys to select among Left, Right, Stereo, and Mono.

3. Changing the audio mode is only connected with the current channel, not all

the channels.

4. Press MENU or EXIT key to close this window.

6.12 Recall

Press the key to switch the current channel to the previous channel.

6.13 FAV

1. Press FAV key to pop up the favorite group window.

2. Press the ◄/► keys to select the favorite group. Press the ▲/▼ keys to select the

channel up or down.. Press OK key at the selected channel to view it in full-screen.

Press MENU or EXIT key to exit.

3. If there is no favorite channel, the system will show "No FAV Channel!" when you press

the FAV key.

6.14 Teletext

Press the key to enter teletext. If there is no teletext, the system will show "No Teletext

Data". Press EXIT key to exit.

English Deutsch Français Nederlands

Italiano Español Magyar Suomi Svenska Česky

6.15 Zoom

1. Press ZOOM key to switch among Zoom*1, Zoom*2, Zoom*3, Zoom*4, Zoom*5,

Zoom*6, Zoom*8, Zoom*12, Zoom*16.

2. In zoom mode, press the ▲/▼, ◄/► keys to move the cursor up, left, right, down.

3. Press MENU or EXIT key to exit

INFORMATIONS

Safety precautions:

To reduce risk of electric shock, this product should ONLY be opened by an authorized

technician when service is required. Disconnect the product from mains and other

equipment if a problem should occur.

Warranty:

No guarantee or liability can be accepted for any changes and modifications of the product

or damage caused due to incorrect use of this product.

General:

Designs and specifications are subject to change without notice.

English Deutsch Français Nederlands

Italiano Español Magyar Suomi Svenska Česky

König SAT-SDFTA11BL User manual

Brand: König

Model: SAT-SDFTA11BL

Category: TV set-top boxes

Type: User manual

Download PDF

report

König SAT-SDFTA11BL User manual

König SAT-SDFTA11BL User manual

Related papers

Other documents