Cary Audio Design CDP 1 Owner's manual

Brand: Cary Audio Design

Model: CDP 1

Category: CD players

Type: Owner's manual

This manual is also suitable for

CDP-1

OWNER’S MANUAL

ooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooo

CDP 1

CD Player

192 kHz / 24 Bit Digital to Analog Coverters

HDCD Decoding

Digital sample rates from 44.1 kHz to 768 kHz

NOTE: Before installing your new component, please read this manual carefully

as it will inform you of the product speciﬁ cations, proper installation and correct

operating procedures for your unit. Also included in this manual are guidelines

on how to service and care for your new Cary Audio Design product.

CDP 1

CD PLAYER

Specifications, Installation

4-9

10-11

Normal Playback

Warranty

Service and Care

Front Panel, Rear Panel & Remote Control

13-14

Various Playback Functions

192

384

512

768

SAMPLE-RATE

CONVERTER

OPEN/CLOSE

PLAY

STOP

PREV.

CDP 1 192kHz / 24Bit HDCD PLAYER

POWER DISPLAY

AES/EBU

RIGHT

LEFT

AES/EBU

ANALOG OUTPUT

TRIGGER

INPUT

COAXIALTOSLINK

AC POWER

[ ] 110-120V

[ ] 220-240V

44.1kHz - 192kHz DIGITAL OUTPUT

CARY AUDIO DESIGN

CDP1HDCDPLAYER

APEX, NC, U.S.A.

HDCD

, High Definition Compatible Digital

and Pacific Microsonics

are either registered trademarks or

trademarks of Pacific Microsonics, Inc. in the United States and /or other countries

HDCD system manufactured under license from Pacific Microsonics, Inc.

This product is covered by one or more of the following :

United States 5,479,168 5,638,074 5,640,161 5,808,574 5,838,274 5,854,600 5,864,311 5,872,531

Australia 669114

Other patents pending.

Country Patent No.

Complies with FDA radiation

performance standards,

21CFR Subchapter J

This device complies with part

15 of the FCC Rules.Operation

is subject to the following two

conditions:(1) This device may

not cause harmful interference,

and (2) this device must accept

any interference received,

including interference that may

cause undesired operation.

RS 232

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire or electric shock, do

not expose this appliance to rain or moisture. The lightning

flash with arrowhead symbol within an equilateral triangle is

intended to alert the user to the presence of un-insulated

dangerous voltage within the product’s enclosure that may

be of sufficient magnitude to constitute a risk of electric

shock to persons.

CAUTION: To reduce the risk of electric shock, do not remove the cover. There are no user serviceable parts inside.

Please refer to qualified personnel for service.

ALERT: The exclamation point within an equilateral triangle is intended to alert the user of the presence of important

operating and maintenance (servicing) instructions in the literature accompanying the component.

1. READ ALL INSTRUCTIONS: All the safety and operating instructions of your Cary Audio equipment should be read

before power is applied to the equipment.

2. RETAIN OWNER'S MANUAL: These safety and operating instructions should be retained for future reference.

3. HEED WARNING: All warnings on the unit and in the operating instructions should be adhered to.

4. FOLLOW INSTRUCTIONS: All operating and use instructions should be followed.

5. CLEANING: Unplug the unit from the wall outlet before cleaning. The unit should be cleaned only as recommended

by the manufacturer.

6. ATTACHMENTS: Do not use attachments not recommended by the unit manufacturer as they may cause hazards.

7. WATER AND MOISTURE: Do not use the unit near water - for example, near a bath tub, wash bowl, kitchen sink,

or laundry tub; in a wet basement; or near a swimming pool.

8. ACCESSORIES: Do not place the unit on an unstable cart, stand, tripod, bracket, or table. The unit may fall,

causing serious injury to a child, an adult, or damage to the unit. Mounting of the unit should follow the

manufacturer's instructions and should use a mounting accessory recommended by the manufacturer.

9. VENTILATION: Slots and openings in the cabinet are provided for ventilation to ensure reliable operation of the

unit and to protect it from overheating. These openings must not be blocked or covered. The top or bottom panel

openings should never be blocked by placing the unit on a bed, sofa, rug, or other similar surface. The unit should

not be installed in a built-in location such as a bookcase or rack unless proper ventilation is provided. There should

be free space of at least 6 inches (16cm) above the unit and an opening behind the unit.

10. GROUNDING OR POLARIZATION: The unit may be equipped with a polarized alternating current line plug (a

plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety

feature. If you cannot insert the plug fully into the outlet, try reversing the plug. If the plug should fail to fit, contact

a licensed electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug.

11. POWER SOURCES: The unit should be operated only from the type of power source indicated on the marking

label. If you are not sure of the type of power supplied to your home, consult your unit dealer or local power

company.

12. POWER CORD PROTECTION: Power supply cords should be routed so that they are unlikely to be walked on or

pinched by items placed on or against them. Pay close attention to cords where they enter a plug, or a convenience

receptacle, and the point where they exit from the unit.

13.

OUTDOOR ANTENNA GROUNDING: If an outside antenna or cable system is connected to the unit, be sure the

antenna or cable system is grounded so as to provide protection against voltage surges and built-up static charges.

Article 810 of the National Electrical Code, NSI/NFPA 70, provides information regarding proper grounding of the

mast and supporting structure, grounding of the lead-in wire to an Antenna-discharge unit, size of grounding

conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the

grounding electrode.

IMPORTANT SAFETY INSTRUCTIONS

14. LIGHTNING: For added protection for the unit during a lightning storm, or when it is left unattended and unused

for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent

damage to the unit due to lightning and power line surges.

15. POWER LINES: An outside antenna system should not be located in the vicinity of overhead power lines or other

electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside

antenna system, take extreme care to keep from touching such power lines or circuits as contact with them might be

fatal.

16. OVERLOADING: Do not overload wall outlets, extension cords, or integral convenience receptacles as this can

result in a risk of fire or electric shock.

17. OBJECT AND LIQUID ENTRY: Never push objects of any kind into the unit through openings as they may touch

dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind

on the unit.

18. SERVICING: Do not attempt to service the unit yourself as opening or removing covers may expose you to

dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

19. REPLACEMENT PARTS: When replacement parts are required, be sure the service technician has used

replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized

substitutions may result in fire, electric shock or other hazards.

20. SAFETY CHECK: Upon completion of any service or repairs to the unit, ask the service technician to perform safety

checks to determine that the unit is in proper operating condition.

21. WALL OR CEILING MOUNTING: The unit should be mounted to a wall or ceiling only as recommended by the

manufacturer.

22. HEAT: The unit should be situated away from heat sources such as radiators, heat registers, stoves, or other units

(including amplifiers) that produce heat.

23. IMPORTANT SAFETY NOTE: Before connecting a new component such as the DVD 7 to your audio or home

theater system it is always good practice to make certain that all components are turned off, and preferably

unplugged from their AC power source. Many modern electronics products feature automatic turn-on circuits that

may be activated during an installation, causing the potential for damage to electronic components and/or speakers.

Such damage is not covered by product warranties and Cary Audio specifically disclaims responsibility for any such

damage.

Power Cord: The removable power cord that is shipped with the player is specifically designed to be used with this

product. Other AC cords may be used, so consult your dealer for advice on AC power cords and high quality wire in

your system.

AC Fuse: The fuse is located inside the chassis and is not user serviceable. If power does not

come on, contact your authorized service representative.

Wiring: Cables that run inside of walls should have the appropriate markings to indicate compliance with, and listing

by the UL, CSA or other standards required by the UL, CSA, NEC or your local building code. Questions about cables

inside of walls should be referred to a qualified custom installer, or a licensed electrician or low-voltage contractor.

Do Not Open the Cabinet: There are no user serviceable components inside this product. Opening the cabinet

may present a shock hazard, and any modification to the product will void your warranty. If water or any metal

object, such as a paper clip, coin, or staple accidentally falls inside the unit, disconnect it from the AC power source

immediately and contact Cary Audio for further instructions.

24.

RECORDING COPYRIGHT: Recording of copyrighted material for other than personal use is illegal without

permission of the copyright holder.

25. NOTE TO CATV SYSTEM INSTALLER: This reminder is provided to call the CATV system installer's attention to

article 820-40 of the NEC, ANSI/NFPA 70, which provides guidelines for proper grounding and, in particular, specifies

that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry

as practical.

IMPORTANT SAFETY INSTRUCTIONS

26. FCC INFORMATION FOR USER:

CAUTION: ANY changes or modifications not expressly approved by the party responsible

for compliance could void the user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to

Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates and can radiate radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from where the receiver is connected.

27. OUTDOOR ANTENNA INSTALLATION/SAFE ANTENNA AND CABLE

CONNECTION: If an outside antenna or cable system is connected to

the equipment, be sure the antenna or cable system is grounded so as to

provide protection against built up static charges and voltage surges,

Section 810 of the national Electrical Code, ANSI/NFP A70 (in Canada,

part 1 of the Canadian Electrical Code) provides information with respect

to proper grounding of the mast and supporting structure, grounding of

the lead-in wire to an antenna discharge unit, size of grounding

conductors, location of antenna discharge unit, connection to grounding

electrodes and requirements for the grounding electrode.

Keep Antenna Clear of High Voltage Power Lines or Circuits

An outside antenna system should be located well away from power lines, electric light or power circuits and where

it will never come into contact with these power sources if it should happen to fall. When installing an outside

antenna, extreme care should be taken to avoid touching power lines, circuits or other power sources as this could

be fatal. Because of the hazards involved, antenna installation should be left to a professional.

Front Panel

1112

POWER button:

* Press once to turn the power ON.

* Press again to set to the "OFF" position and turn the power off. The player will

enter into "Standby" and the blue LED will light.

SAMPLE-RATE CONVERTER button:

* Use this button to switch the analog output sample-rate converter mode.

OFF(44.1) ---> 96 ---> 192 ---> 384 ---> 512 ---> 768 kHz --->

DISPLAY button:

* Use this button to switch the player display brightness levels.

* There are 3 brightness levels, low, medium and high, plus OFF.

DISC HOLDER:

*Loaddiscshere.

DISC HOLDER OPEN/CLOSE button:

* Press this button to open and close the disc holder.

PLAY button:

* Press this button to start playback.

STOP button:

*Pressthisbuttontostopplayback.

192

384

512

768

SAMPLE-RATE

CONVERTER

OPEN/CLOSE

PLAY

STOP

PREV.

CDP 1 192kHz / 24Bit HDCD PLAYER

POWER DISPLAY

Front Panel

1112

AUTOMATIC SEARCH REVERSE button:

* Press this button to return the pickup to the beginning of the present track.

* Press again to return to other tracks.

AUTOMATIC SEARCH FORWARD button:

* Press this button to move the pickup forward to the beginning of the next track.

* Press again to move ahead to other tracks.

ALPHANUMERIC display:

* This multi-character display provides a wide range of information concerning

the operation of the CDP 1.

HDCD indicator:

* This indicator lights when the HDCD decoding function is "ON".

* This function decodes HDCD disks at the 44.1 kHz setting ONLY. This is a

part of the HDCD algorithm.

SAMPLE-RATE CONVERTER indicator:

* This indicator lights when the digital and analog output sample-rate converter

function is "ON".

DISPLAY indicator:

* This indicator lights when display brightness is set "OFF" mode.

POWER indicator:

* This indicator lights when the player is switched off.

192

384

512

768

SAMPLE-RATE

CONVERTER

OPEN/CLOSE

PLAY

STOP

PREV.

CDP 1 192kHz / 24Bit HDCD PLAYER

POWER DISPLAY

Rear Panel

RIGHT CHANNEL ANALOG OUTPUT JACK (AES/EBU BALANCED):

* Use this jack for connection to the amplifier's balanced input jack.

LEFT CHANNEL ANALOG OUTPUT JACK (AES/EBU BALANCED):

* Use this jack for connection to the amplifier's balanced input jack.

RIGHT CHANNEL ANALOG OUTPUT JACK (RCA UNBALANCED):

* Use this jack for connection to the amplifier's RCA unbalanced input jack.

LEFT CHANNEL ANALOG OUTPUT JACK (RCA UNBALANCED):

* Use this jack for connection to the amplifier's RCA unbalanced input jack.

DIGITAL OUTPUT JACK (TOSLINK):

* 44.1 kHz-192 kHz digital data is output from this jack.

DIGITAL OUTPUT JACK (COAXIAL):

* 44.1 kHz-192 kHz digital data is output from this jack.

DC TRIGGER INPUT TERMINALS:

* Connect a device that can triggered by DC + 12V.

AES/EBU

RIGHT

LEFT

AES/EBU

ANALOG OUTPUT

TRIGGER

INPUT

COAXIALTOSLINK

AC POWER

[ ] 110-120V

[ ] 220-240V

44.1kHz - 192kHz DIGITAL OUTPUT

CARY AUDIO DESIGN

CDP 1 HDCD PLAYER

APEX, NC, U.S.A.

HDCD

, High Definition Compatible Digital

and Pacific Microsonics

are either registered trademarks or

trademarks of Pacific Microsonics, Inc. in the United States and /or other countries

HDCD system manufactured under license from Pacific Microsonics, Inc.

This product is covered by one or more of the following :

United States 5,479,168 5,638,074 5,640,161 5,808,574 5,838,274 5,854,600 5,864,311 5,872,531

Australia 669114

Other patents pending.

Country Patent No.

Complies with FDA radiation

performance standards,

21CFR Subchapter J

This device complies with part

15 of the FCC Rules.Operation

is subject to the following two

conditions:(1) This device may

not cause harmful interference,

and (2) this device must accept

any interference received,

including interference that may

cause undesired operation.

RS 232

Rear Panel

POWER INPUT(AC IN):

* Connect to an AC power supply using the included power supply cord.

RS 232 PORT:

* The RS-232 port is used in conjunction with an external controller to control the

operation of the CDP 1 by using an external device.(This is for custom installation

use. Consult your dealer for more information.)

* The pin assignments of the XLR-type male analog outputs:

Pin 1: Signal ground

Pin 2: Signal + (non-inverting)

Pin 3: Signal - (inverting)

Connector ground lug: chassis ground

Refer to your amplifier's operating manual to verify that the XLR pin

assignments of its input connectors correspond to the CDP 1.

If they are different, wire the XLR cable so that the appropriate XLR

output pin connects to the equivalent XLR input pin.

AES/EBU

RIGHT

LEFT

AES/EBU

ANALOG OUTPUT

TRIGGER

INPUT

COAXIALTOSLINK

AC POWER

[ ] 110-120V

[ ] 220-240V

44.1kHz - 192kHz DIGITAL OUTPUT

CARY AUDIO DESIGN

CDP 1 HDCD PLAYER

APEX, NC, U.S.A.

HDCD

, High Definition Compatible Digital

and Pacific Microsonics

are either registered trademarks or

trademarks of Pacific Microsonics, Inc. in the United States and /or other countries

HDCD system manufactured under license from Pacific Microsonics, Inc.

This product is covered by one or more of the following :

United States 5,479,168 5,638,074 5,640,161 5,808,574 5,838,274 5,854,600 5,864,311 5,872,531

Australia 669114

Other patents pending.

Country Patent No.

Complies with FDA radiation

performance standards,

21CFR Subchapter J

This device complies with part

15 of the FCC Rules.Operation

is subject to the following two

conditions:(1) This device may

not cause harmful interference,

and (2) this device must accept

any interference received,

including interference that may

cause undesired operation.

RS 232

IR INPUT JACK:

* Use this jack to connect external IR sensors.

PROGRAM

DELETE

REPEAT

CDP1R/C

Remote Control

SRC

0+10

PROGRAM

DELETE

REPEAT

CLEAN

TIME

-VOLUME+

POWER

INPUT SELECTOR

L BALANCED R

-VOLUME+

AMPLIFIER USE ONLY

SRC

BRIGHT

MUTE

Select the sample-rate converter on or off,

and cycle through sample-rate settings.

This button switches the power on and off.

This button opens and closes the CD

loading tray.

This button interrupts and resumes play.

Start play. Playing a program.

Stops play.

This button mutes the sound.

Press again to resume sound.

Clears a program.

Presets tracks to be played by keying in

track numbers.

Fast search for a passage.

Selects another track during play.

Repeat play.

CLEAN

TIME

CDP1R/C

Remote Control

Clears the last track number during

programming.

Displays the remaining time of a track or

it displays the total remaining time of a disc.

BRIGHT

VOLUME

Select the display brightness levels - low,

medium, high, and OFF settings available.

Digit keys.

Control the volume. (0 dB to 63 dB)

0+10

PROGRAM

DELETE

REPEAT

CLEAN

TIME

-VOLUME+

POWER

INPUT SELECTOR

L BALANCED R

-VOLUME+

AMPLIFIER USE ONLY

SRC

TUBE

BRIGHT

MUTE

CARY amplifier use only

Specifications

Operating the CDP 1 CD player is a simple procedure, since each unit is designed for long term

stability in virtually any home operating situation. However, if the unit is operated outside the

parameters outline in this owner's manual, damage may result. Please read this manual carefully

before putting your new Cary Audio Design CDP 1 in operation.

1.1 Specifications

The following section describes the CDP 1 CD player basic specifications.

Specifications are subject to change without notice or obligation.

CD Mechanism

Triple-beam laser, multi speed CD/DVD ROM transport

Formats

CD AUDIO (CD-DA), CD-R, CD-RW

Master Clock Jitter

Digital Filter

Digital / Analog Converters

Analog Filter

Analog Outputs

Digital Output

Frequency Range

Amplitude Linearity

Frequency Response

Signal-to-Noise Ratio

Balanced

Trigger Input

Power Input

Power Consumption

Below measurable levels

CARY DSP 300 with HDCD decoding

Two (2) Burr Brown PCM 1792u

3 Order Bessel

Balanced XLR, Single - Ended RCA

Coaxial, Toslink operating at Sample Frequency (FS)

from 44.1 kHz / 16 bit to 192 kHz / 24 bit

2 Hz - 22 kHz (44.1 kHz)

0.1 dB (20 Hz-20 kHz)

12.0 V DC

Configured at the factory for either

110-117 or 220-234 V AC, 50-60 Hz

50 Watts

Phase Linearity

3 (20Hz-20kHz)

129 dB (1 kHz)

122 dB (1 kHz)

Channel Separation 104 dB (1kHz)

Total Harmonic Distortion

0.003 % (1 kHz)

Audio Output level 3.0 V RMS (220 output impedance)

+3.0 V RMS (440 output impedance)

IR Input

PHILIPS RC 5 IR code

Comms.

RS 232 full remote configuration interface

Installation

2.1 Unpacking

All Cary Audio Design shipping containers have been specifically designed to protect their

contents and special care has been taken to prevent damage under normal shipping conditions.

Mishandling should be evident upon inspection of the shipping container. If the CDP 1 player

mechanism or other damage is found after unpacking and visual inspection, take care not to

destroy the evidence so that the shipping agent may inspect the damage. If necessary, document

the damage with photographs and contact the shipping company immediately.

This section describes the unpacking and installation procedures for the CDP 1 player.

Carefully remove your CDP 1 CD player from its packing carton and examine it closely for signs

of shipping damage. It is highly recommended to save all original packing cartons to protect your

CDP 1 from damage should you wish to store it or ship it for after-sales service. Replacement

cartons and packing are available at a nominal charge from Cary Audio Design, ifever required.

2.2 Placement

In general, the location of your new CDP 1 is not critical. However, certain precautions must be

taken to ensure optimum performance. Avoid extremely hot locations such as near radiators

or other heating units. Avoid getting it wet or using it near water. Do not stack the CDP 1 on top

of a power amplifier. Allow 4-6 inches (10-15cm) above the unit for proper ventilation.

2.3 Power Requirement

The CDP 1 CD player is designed to operate from AC mains current. The design AC voltage is

either 110-117V or 220-234V AC at 50-60 Hz.

2.4 Connections

WARNING

MAKE NO ATTEMPT TO PUT THE CDP 1 CD PLAYER IN SERVICE WITH

THE TOP COVER REMOVED. CONTACT WITH HIGH VOLTAGE INSIDE

THECDP1CDPLAYERCANBEFATAL!

Digital Outputs: The outputs send a digital signal and should only be connected to the

appropriate digital signal input of an accompanying component.

Analog Outputs: These are for connection to the CD or AUX input jacks of an

appropriate preamplifier or integrated amplifier.

Normal Playback

3.1 Starting Playback

Press the POWER button to turn on the power.

Press the OPEN/CLOSE button.

* The disc holder opens.

Load the disc you want to play.

Press the PLAY button.

* Playback starts.

* Playback stops automatically after the last track on the disc has been played.

3.2 Stopping Playback

During playback, press the STOP button.

* Playback stops.

192

384

512

768

SAMPLE-RATE

CONVERTER

OPEN/CLOSE

PLAY

STOP

PREV.

CDP 1 192kHz / 24Bit HDCD PLAYER

POWER DISPLAY

Various Playback Functions

4.1 Playing a specific track (Remote control unit only) [Direct Play]

Use the number buttons and + 10 button to select the desired track.

* Playback starts from the selected track.

During playback, press the PAUSE button on the remote control unit.

* Playback pauses.

* To resume playback from the position at which the disc is paused,

press PLAY button.

1.Press the NEXT button. (Operable with the remote control unit)

* Press the button more than once to move ahead to the beginning

of subsequent tracks.

* When the NEXT button is pressed during random playback, the

next track is selected at random and played.

4.2 Stopping playback temporarily (Remote Control unit only) [Pause]

4.3 Automatic Search

2.Press the PREV. button. (Operable with the remote control unit)

* Press the button more than once to move back to the beginning

of previous tracks.

+10

PROGRAM

DELETE

REPEAT

CLEAN

TIME

-VOLUME+

POWER

INPUT SELECTOR

L BALANCED R

-VOLUME+

AMPLIFIER USE ONLY

SRC

BRIGHT

MUTE

Various Playback Functions

4.5 Playing the tracks in the desired order (Remote control unit only)

Usethisfunctiontoselectthetracksonthediscandplaythem

in the desired order.

Up to 99 tracks can be programmed.

1.In the stop mode, press the PROGRAM button.

2.Press the number to select the track to be programmed.

* For example, to program the 3rd track and 9th track,

Press PROGRAM , 3 and 9 .

3.Press the PLAY button.

* The tracks are played in the programmed order.

Playing all the tracks repeatedly.

1. In the PLAY mode, press the REPEAT button twice.

* The "REPEAT ALL" indicator lights.

* To cancel the all-track repeat mode, press the REPEAT button

a third time.

4.6 Repeat play (Remote control unit only)

Playing a single track repeatedly.

1.During playback, press the REPEAT button once.

* The "REPEAT ONE" indicator lights.

* To cancel the one-track repeat mode, press the REPEAT button

two more times.

4.4 Finding the desired spot while listening to the sound (Remote Control unit only)

Use this function to skip forward or backward while listening to the sound.

This function comes in handy for finding the desired spot in the middle of

long tracks.

1.During Playback, press and hold in the button.

* When the button is released, normal playback resumes from that point.

2.During playback, press and hold in the button.

* When the button is released, normal playback resumes from that point.

0+10

PROGRAM

DELETE

REPEAT

CLEAN

TIME

-VOLUME+

POWER

INPUT SELECTOR

L BALANCED R

-VOLUME+

AMPLIFIER USE ONLY

SRC

BRIGHT

MUTE

0+10

PROGRAM

DELETE

REPEAT

CLEAN

TIME

-VOLUME+

POWER

INPUT SELECTOR

L BALANCED R

-VOLUME+

AMPLIFIER USE ONLY

SRC

BRIGHT

MUTE

0+10

PROGRAM

DELETE

REPEAT

CLEAN

TIME

-VOLUME+

POWER

INPUT SELECTOR

L BALANCED R

-VOLUME+

AMPLIFIER USE ONLY

SRC

BRIGHT

MUTE

[Programmed play]

Service and Care

5.2 Factory Service

The cabinet housing and front panel of the CDP 1 may be cleaned with a soft cloth and Windex

or a mild window cleaner. The frequency of cleaning will be governed by the operating

environment cleanliness. Do not use benzene, harsh or abrasive chemicals to clean the front or

rear panel as they may remove or damage the labels.

5.1 CDP 1 Care and Cleaning

Careful consideration has been given to the design of you CDP 1 CD player to keep maintenance

problems to a minimum. Any service problems should be referred to our Customer Service

Department phone number (919) 355-0010 from 1-5 PM US East Coast Time Zone.

Do NOT return the CDP 1 to the factory without a return authorization number ( ) from the

Customer Service Department.

Cary Audio Design will assume no responsibility if the shipping company refuses to pay

damage due to your improper packing or lack of insurance should the unit be lost or damaged

in shipment. Please retain and always use the original shipping carton for the CDP 1 in the event

that you move or after service is needed.

CAUTIONS

NEVER REMOVE OR INSERT THE BACK PANEL AC PLUG

WHEN THE UNIT IS ON OR THE AC CORD IS PLUGGED

INTO THE WALL.

PLEASE OBSERVE THE SAFETY DIRECTIONS IN THIS MANUAL

UNITED STATES LIMITED WARRANTY

Cary Audio Design warrants to the original United States purchaser for use in the United States that Cary

Audio Design vacuum tube or solid state power amplifiers, surround sound processors or preamplifiers shall

be free from defects in parts or workmanship for three (3) years from the date of the original purchase.

Vacuum tubes, if any are used in the component, are offered a 90 day from purchase date exchange policy

against defects with the exception of the CAVT 300B vacuum tube which has a (1) one year from purchase

date exchange policy. Any digital drive design, whether a Cary Audio Design CD or SACD player or a Cary

Cinema DVD player, has a limited one year parts and labor warranty against defects in manufacture. This is

a limited warrant, for the original purchaser only and does not transfer to any subsequent owner.

During the limited warranty period, Cary Audio Design or an authorized Cary Audio Design service facility

will provide free of charge both parts and labor necessary to correct any defects in material or

workmanship.

To obtain such warranty service, the original purchaser must:

1. Complete and send in the warranty Registration Card within 15 days of purchase.

2. If claiming service the owner must send a fully filled in copy of the original sales receipt along with

any unit sent in for service showing the AUTHORIZED CARY AUDIO DESIGN DEALER’S name, the

new selling price, the buyer’s name, e-mail or phone number and address on the receipt. Blank

receipts will NOT validate the limited warranty for service.

3. Notify Cary Audio Design as soon as possible after the discovery of a possible defect and submit

the following information to determine eligibility for warranty:

(a) The model number and serial number;

(b) A fully filled in copy of the original sales receipt showing the original selling price, purchasers

name and address filled in by an AUTHORIZED CARY AUDIO DESIGN DEALER with the original

date of purchase shown on the form;

4. Deliver the product to Cary Audio Design or the nearest authorized service facility or ship with all

freight and insurance charges prepaid, in its original packing container or equivalent, to Cary

Audio.

Correct maintenance, repair and use are important to obtain performance from this product. Therefore,

please carefully read the Operating Manual. This warranty does not apply to any defect that Cary Audio

Design in its sole discretion determines is due to:

1. Improper maintenance or repair, including the installation of parts or accessories that do not

conform to the quality and the specifications of the original parts.

2. Misuse, abuse, neglect or improper installation.

3. Accidental or incidental damage.

WARRANTY DISCLAIMER

Except for the express warranties stated herein, Cary Audio Design disclaims all other warranties including,

without limitation, all implied warranties of merchantability and fitness for a particular purpose. The

foregoing constitutes Cary Audio Design’s entire obligation with respect to this product, and the original

purchaser and any user or owner shall have no other claim for incidental or consequential damages. Some

states do not allow the exclusion or limitation of incidental or consequential damages, so the above

limitation and exclusion may not apply to you. This warranty gives legal rights and you may also have other

rights, which vary from state to state.

EXCLUSIVE REMEDY

Notwithstanding the foregoing, the purchaser’s exclusive remedy for any breach of warranty, express or

implied, is limited to the repair or replacement of the defective unit or the refund of the purchase price, at

the option of Cary Audio Design. Under no circumstances is Cary Audio Design liable for incidental or

consequential damages. Any implied warranties imposed by law terminate one (1) year from the date of

purchase.

INTERNATIONAL PURCHASERS (Export markets)

Cary Audio Design warrants its merchandise to purchasers within the United States exclusively for use within

the United States of America. It provides no other warranties, expressed or implied. If you are living

outside the USA, please consult with your local dealer or distributor to determine the details of your local

warranty.

CARY AUDIO DESIGN

1020 Goodworth Drive, Apex, NC 27539

phone 919-355-0010

fax 919-355-0013

www.caryaudio.com

ooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooo

ooooooooooooooooooo

Cary Audio Design CDP 1 Owner's manual

Brand: Cary Audio Design

Model: CDP 1

Category: CD players

Type: Owner's manual

This manual is also suitable for

CDP-1

Download PDF

report

Cary Audio Design CDP 1 Owner's manual

This manual is also suitable for

Cary Audio Design CDP 1 Owner's manual

Related papers

Other documents