Voxx APS596Z User guide

Category
Remote starters
Type
User guide

This manual is also suitable for

Voxx APS596Z is a security system with keyless entry that offers a variety of features to enhance your vehicle's security and convenience. With customizable options for arming and disarming, trunk shunt input, remote programming, alarm notifications, and user-programmable LED, you can tailor the system to your specific needs. The shock sensor ensures reliable detection of attempted break-ins, while the dome delay programming and negative output control provide added flexibility.

Voxx APS596Z is a security system with keyless entry that offers a variety of features to enhance your vehicle's security and convenience. With customizable options for arming and disarming, trunk shunt input, remote programming, alarm notifications, and user-programmable LED, you can tailor the system to your specific needs. The shock sensor ensures reliable detection of attempted break-ins, while the dome delay programming and negative output control provide added flexibility.

20 Blue
Trunk Shunt Input (-/+)
19 Orange
Starter Kill Relay / An-Grind Output (-)
18 Red/Black
Disarm 2 Input (-/+)
17 Black/White
Horn Output (-) (NOC 9)
16 Red/Yellow
Disarm 1 Input (-/+)
15 Dk. Blue/Black
Ch. 3 Alt Output (-) (NOC 8)
14 Green/Black
Arm 2 Input (-/+)
13 Green/White
Domelight Output (-) (NOC 7)
12 Green/Yellow
Arm 1 Input (-/+)
11 Lt. Blue/Green
Ch. 5 AUX Output (-) (NOC 6)
10 Dk. Green
Instant Trigger Input
(-)
9 Green/Lt. Blue
Ch. 4 AUX Output (-) (NOC 5)
8 Lt. Green
Trunk Trigger Input (-) (PIC 2)
7 Dk. Blue
Trunk Output (-) (NOC 4)
6 Gray/Black
Hood Input (-) (PIC 1)
5 White/Blue
Headlight Output (-) (NOC 3)
4 Purple/Brown
Door Trigger Input (- / +)
3 Green
Unlock Output (-) (NOC 2)
2
Empty Empty
1 Red
Lock Output (-) (NOC 1)
20 Pin Input/Output
1
2
3
4
1 2 3
4
1
2
3
4
1
White Data RX
2
Black Ground (-)
3 Blue
Data TX
4 Red
BaƩery 12V (+)
DBI
1
Green Data RX
2
Blue Data TX
3 Black
Ground (-)
4 Red
BaƩery 12V (+)
RF
1
Blue Data TX
2
White Data RX
3 Black
Ground (-)
4 Red
BaƩery 12V (+)
CarLink
4 Red
Baery 12V (+)
3 Black
Ground (-)
2
Blue Data TX
1
White Data RX
Weblink
4 Red
Baery 12V (+)
3 Black
Ground (-)
2
Blue Warn Away (-)
1
Green Full Trigger (-)
Shock
1 2 3 4
VOXX
FLCART Dock
Replacement Part #4120459
Replacement Part #4120460
Replacement Part #4120461
Not Included
Not Included
Not Included
Not Included
85 Red
Ignion Input (+)
86 Orange
Ground While Armed (-)
87A
Black Starter Output - Motor Side
30
Black/White Starter Input - Key Side
Starter Kill
86
85
87
87A
30
1 White
Parking Light (30) Output
2 Black
Ground Input (-)
3 White/Red
Parking Light (87) Input
4 Yellow
IgniƟon Input (+)
5 White/Black
Siren Output (+)
6 Red
BaƩery 12V Input (+)
6 Pin Power
P
Replacement Part #4360828
1 Black Ground (-)
2 Gray Valet Switch Input
Valet
1 Blue LED Output (-)
2 Red BaƩery 12V (+)
LED
Replacement Part #4120474
Replacement Part #4360833
This Harness is included with the FLCART.



Not Included
19
17
15
13
11
9
7
5
3
1 2
4
6
8
10
12
14
16
18
20
1
2
3
4
1 3 5
2 4 6
19
17
15
13
11
9
7
5
3
1 2
4
6
8
10
12
14
16
18
20
APS596Z
Security w/Keyless Entry
System Layout
2020 Voxx Electronics. All Rights Reserved.
Shock Sensor
Part #4700033
4180068 185SP18LCDSP
APS596Z
Security w/Keyless Entry
Quick Installaon Guide
For Complete Installaon Guide and Technical Support
Please Visit
www.voxxuniversity.com
Or Call
1-800-225-6074
Nocaons
Remote Programming
1 Chirp 2 Chirp
1 Lock / Unlock Funcon 500ms 3.5sec
2 Ignion Lock OFF ON
3 Ignion Unlock OFF Unlock All
4 Exterior Illuminaon OFF With Arm
5 Auto Relock OFF Auto Lock Only
6 Auto Arming / Locking OFF Auto Arm Only
7 Nocaon Sound Both Siren
8 Horn Timing 16ms 30ms
9 Valet Override Method Valet Custom Code
10 Driver Priority Unlock OFF ON
11 Silent Choice OFF From Transmier
12 Security Prole All On Doors O
13 Door Trigger Input Negave Posive
14 Park Light / Trunk Swap OFF ON
15 Data Port Protocol ADS DBI
16 1 or 2 Wire Disarm 2 Wire 1 Wire
17 Disarm Input 120ms Dr OR Pass 80ms Dr OR Pass 120ms, UL & Light 80ms, UL & Light
18 Arm 1 Input Auto Detect Posive Negave
19 Disarm 1 Input Auto Detect Posive Negave
20 Arm 2 Input Auto Detect Posive Negave
21 Disarm 2 Input Auto Detect Posive Negave
22 Trunk Shunt Input Auto Detect Posive Nega
ve
23 Dome Light Delay Timer OFF / Program 15sec 30sec
24 Alarm Trigger Length 30sec 45sec 60sec
Features
Opons
Features
Negave Output Control (NOC)
AUX Output Control
Factory Keyless Upgrade
Shock Sensor
Negave output control allows any NOC to be programmed for any one of the opons
below. This feature is accessible via FlashLogic Weblink or Weblink Mobile.
Any AUX output can be congured using the AUX Control Menu. This feature is only
accessible via FlashLogic Weblink or Weblink Mobile.
The shock sensor should be mounted to a solid surface in the center of the vehicle.
Once mounted the shock sensor will require adjustment.
To increase sensivity: Turn adjustment dial clockwise.
To decrease sensivity: Turn adjustment dial counter clockwise.
To test sensivity, strike the vehicle with an open palm. Adjust the dial to provide
coverage to as much of the vehicle as possible.
Important Update:
The default data port protocol of this system is ADS. When ashing the FLCAN, or other integraon module, be sure to choose iDatalink 2-Way as the installaon method.
This module will also support DBI. This will require programming Feature Bank 2, Feature 15 to DBI. For Technical Support Visit www.voxxuniversity.com or Call 1-800-225-6074.
Feature Programming
Dome Delay Programming
The APS596Z Feature Banks can be programmed by using the valet buon and the OEM or
Presge remote. To enter Feature Bank programming:
1. Turn the ignion key to ON.
2. Press and release the valet buon three (3) mes. System will beep and ash lights
one (1) me for Feature Bank 1, Remote Programming.
3. Cycle ignion key OFF/ON. System will beep and ash lights two (2) mes for
Feature Bank 2.
4. Press valet buon to cycle features. LED will ash to display feature number.
5. Press lock buon to cycle opons. System will beep to indicate opon number.
To exit Programming cycle ignion key OFF and wait ten (10) seconds. The System will also
automacally exit programming aer sixty (60) seconds of no acvity.
This system can be programmed to ignore the vehicle’s theater dimming dome light. This
feature will be used when connecng the door trigger input to the dome light circuit for
alarm trigger. Note: Vehicle windows should be open to prevent accidental locking of keys
in the vehicle.
Start with all doors closed and the vehicle dome light o.
1. Press Lock, Unlock, Lock, Unlock, Lock, Unlock, Lock. LED will light solid.
2. Open and close the driver door.
The system will monitor the dome light circuit. When the dome light turns o the system
will set the delay me and add an addional two (2) seconds.
Dome Delay Reset
1. Key ON/OFF, ON/OFF, ON/OFF.
2. Press and hold valet buon for ve (5) seconds.
The system will beep one (1) me to indicate reset is complete.
The Feature Bank below can also be programmed using the FlashLogic Weblink or Weblink Mobile.
Please visit www.FlashLogic.com for more detail.
LED Output
Ch. 7 AUX Output
Horn Output
Ground While Armed
(GWA)
Ground While Disarmed
(GWD)
Ch. 3 ALT Output
Ch. 4 AUX Output
Ch. 5 AUX Output
Ch. 6 AUX Output
Lock Output
Unlock Output
Trunk Output
2nd Unlock Output
Dome Light Output
Head Light Output
1 Second Pulse
5 Second Pulse
10 Second Pulse
15 Second Pulse
20 Second Pulse
30 Second Pulse
Push & Hold
Latch ON/OFF
1 Shock
2 Trunk/Hood
3 Door
Data Protocol Selecon
REV. B 2020 Voxx Electronics. All Rights Reserved.
The APS596Z can be used without transmiers as a Factory Keyless Alarm Upgrade. Arm
/ Disarm 1 inputs will be connected to the Driver Door Lock Motor. Arm / Disarm 2 inputs
will be connected to the Passenger Door Lock Motor and / or the Lock Switch. The control
polarity, by default, will be detected automacally upon power up. The Control polarity can
also be manually congured using Feature Bank 2, Features 18-21.
Note: If this feature is supported by FLCAN Arm / Disarm Wires are not required for install.
The Trunk Shunt input will be used if the vehicle is equipped with a factory power trunk
/ hatch release. If equipped, connect the Trunk Shunt input to the factory trunk release
trigger wire. The control polarity, by default, will be detected automacally upon power up.
The control polarity can also be manually congured using Feature Bank 2, Feature 22.
Trunk Trigger
Door Trigger
Instant Trigger
N.C. Door Trigger
Pre-Warn Shock Trigger
Hood Trigger
Fill Shock Trigger
Alarm
When the alarm is triggered the system will provide feedback to the user. Upon disarm,
the system will beep 4x and ash the LED to indicate the Alarm Trigger Zone.
Chirp Delete
System ARM/DISARM chirps can be toggled ON or OFF without entering the Feature
Bank programming.
1. Turn the ignion key ON/OFF.
2. Press and release the valet buon three (3) mes.
The system will respond with one (1) chirp for ON and two (2) Chirps for OFF. This
feature will not aect alarm trigger or programming.
User Programmable LED
System LED nocaons can be turned ON or OFF without entering Feature Bank
programming.
1. Turn the ignion key ON/OFF, ON/OFF.
2. Press and hold valet buon for ve (5) seconds.
The LED will ash one (1) me for ON, two (2) mes for OFF. This feature will not aect
LED ash during programming.
The default data port protocol of this model is ADS (iDatalink 2-Way). This model is
capable of detecng the correct data port protocol (ADS or DBI) and automacally
conguring Feature Bank 2; Feature 18. To inialize the detecon procedure:
1. Press and hold the valet buon.
2. Cycle the vehicle’s Ignion ON/OFF two (2) mes.
3. Release the valet buon.
The system will automacally detect and set the correct data port protocol, ADS or DBI.
Note: This feature is only available on module rmware v2.0 or higher.
PIC Input Control
Programmable Input Control allows any PIC be congured to one of the opons listed
below. This feature is accessible via FlashLogic Weblink or Weblink Mobile.
Notes
The APS596Z includes two (2) programmed remotes. If required, addional remotes can
be programmed to the system. Remote Programming is located in Feature Bank 1. To enter
Remote Auto Programming:
1. Turn the ignion key to ON.
2. Press and release the valet buon three (3) mes. System will beep and ash the
parking lights one (1) me.
Press the lock buon on each remote. The system will beep one (1) mes to indicate the
remote has been programmed. Only primary remote funcons are auto programmed. This
Includes Lock, Unlock, and Trunk/Start.
If using AUX output control, the remote channel must be manually programmed to
the system AUX output. Please see the complete installaon guide for manual remote
programming instrucon.
Note: If programming 2-Way remotes, wait for remote to beep before programming
another remote. This beep is conrmaon that a 2-Way response has been received from
the main module.
  • Page 1 1
  • Page 2 2

Voxx APS596Z User guide

Category
Remote starters
Type
User guide
This manual is also suitable for

Voxx APS596Z is a security system with keyless entry that offers a variety of features to enhance your vehicle's security and convenience. With customizable options for arming and disarming, trunk shunt input, remote programming, alarm notifications, and user-programmable LED, you can tailor the system to your specific needs. The shock sensor ensures reliable detection of attempted break-ins, while the dome delay programming and negative output control provide added flexibility.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI