Alamo Eagle 14 User manual

EAGLE 20/14

Published 03/09 Part NO. 00779092C

OPERATOR’S MANUAL

ALAMO INDUSTRIAL

1502 East Walnut

Seguin, Texas 78155

830-379-1480

FLEX-WING MECHANICAL LEVEL

LIFT ROTARY MOWER

This Operator's Manual is an integral part of the safe operation of this machine and must

be maintained with the unit at all times. READ,

UNDERSTAND, and FOLLOW the Safety

and Operation Instructions contained in this manual before operating the equipment. C01-

Cover

$0.00

To the Owner/Operator/Dealer

All implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-minded

operator who recognizes the potential hazards and follows reasonable safety practices. The manufacturer has

designed this implement to be used with all its safety equipment properly attached to minimize the chance of

accidents.

BEFORE YOU START!! Read the safety messages on the implement and shown in your manual. Observe the

rules of safety and common sense!

WARRANTY INFORMATION:

Read and understand the complete Warranty Statement found in this Manual. Fill out the Warranty Registration

Form in full and return it to within 30 Days. Make certain the Serial Number of the Machine is recorded on the

Warranty Card and on the Warranty Form that you retain.

Table of Contents

SAFETY SECTION .........................................................................................1-1

General Safety Instructions and Practices .........................................................................................................1-2

Operator Safety Instructions and Practices .......................................................................................................1-3

Equipment Operation Safety Instructions and Practices ....................................................................................1-6

Connecting or Disconnecting Implement Safety Instructions and Practices ....................................................1-12

Transporting Safety Instructions and Practices ...............................................................................................1-13

Maintenance and Service Safety Instructions and Practices ...........................................................................1-15

Storage and Parking Safety Instructions and Practices ...................................................................................1-17

Concluding Safety Instructions and Practices ..................................................................................................1-17

Decal Location .................................................................................................................................................1-18

Decal Description .............................................................................................................................................1-20

Federal Laws and Regulations ........................................................................................................................1-29

INTRODUCTION SECTION ............................................................................2-1

ASSEMBLY SECTION ....................................................................................3-1

General Assemby ..............................................................................................................................................3-2

Blade Carrier and Blades ...................................................................................................................................3-2

Tongue Attachment ............................................................................................................................................3-3

Level Rod Assembly ..........................................................................................................................................3-3

Wing Section Attachements ...............................................................................................................................3-4

Hose Bracket Attachment ..................................................................................................................................3-4

Center Section ...................................................................................................................................................3-5

Level Lift Axle Attachment (Figure Asm-R-0017 ) ..............................................................................................3-5

Axle Adjustment Rod Attachment ......................................................................................................................3-6

Center Axle Hydraulic Cylinder Attachment .......................................................................................................3-6

Wing Section Hydraulic Cylinder Attachment .....................................................................................................3-6

TIRES AND WHEELS ........................................................................................................................................3-7

Rubber Stop Attachment ....................................................................................................................................3-8

Baffle Kit Assembly (Optional) ...........................................................................................................................3-8

Rubber Deflectors (Standard) ............................................................................................................................3-9

Chain Guard Attachment .................................................................................................................................3-10

Counterweight Attachment ...............................................................................................................................3-11

Driveline Attachment ........................................................................................................................................3-11

Driveline Clamp Cone Yoke Operating Instructions .........................................................................................3-12

Canopy Shields ................................................................................................................................................3-12

Three Spool Control Valve Installation .............................................................................................................3-13

OPERATION SECTION ..................................................................................4-1

Standard Equipment and Specifications ............................................................................................................4-3

OPERATOR REQUIREMENTS .........................................................................................................................4-4

ROPS and Seat Belt ..........................................................................................................................................4-5

Tractor Safety Devices .......................................................................................................................................4-6

Tractor Horsepower ...........................................................................................................................................4-6

Drawbar .............................................................................................................................................................4-6

Front End Weight ...............................................................................................................................................4-7

Power Take Off (PTO) .......................................................................................................................................4-7

GETTING ON AND OFF THE TRACTOR .........................................................................................................4-8

Boarding the Tractor ..........................................................................................................................................4-8

Dismounting the Tractor .....................................................................................................................................4-8

STARTING THE TRACTOR ..............................................................................................................................4-9

CONNECTING THE MOWER TO THE TRACTOR .........................................................................................4-10

Connecting the Mower Tongue to the Tractor .................................................................................................4-10

Safety Tow Chain .............................................................................................................................................4-11

Connecting Mower Hydraulic Lines to the Tractor ...........................................................................................4-11

SETTING THE MOWER ..................................................................................................................................4-12

Setting Deck Pitch ............................................................................................................................................4-14

Lowest Cutting Height ......................................................................................................................................4-14

DRIVELINE ATTACHMENT ............................................................................................................................4-16

Driveline Length Check ....................................................................................................................................4-16

Constant Velocity (CV) Driveline ......................................................................................................................4-18

PRE-OPERATION INSPECTION AND SERVICE ...........................................................................................4-19

Tractor Pre-Operation Inspection/Service ........................................................................................................4-20

Mower Pre-Operation Inspection/Service ........................................................................................................4-20

Cutting Component Inspection .........................................................................................................................4-24

Blade Bolt Inspection .......................................................................................................................................4-26

DRIVING THE TRACTOR AND IMPLEMENT .................................................................................................4-29

Starting the Tractor ..........................................................................................................................................4-30

Brake and Differential Lock Setting ..................................................................................................................4-30

Operating the Mower Wings ............................................................................................................................4-30

Driving the Tractor and Cutter ..........................................................................................................................4-32

Crossing Ditches and Steep Inclines ...............................................................................................................4-33

OPERATING THE TRACTOR AND IMPLEMENT ...........................................................................................4-34

Foreign Debris Hazards ...................................................................................................................................4-35

Bystanders/Passersby Precautions .................................................................................................................4-35

Engaging the Power Take Off (PTO) ...............................................................................................................4-36

PTO RPM and Ground Speed .........................................................................................................................4-37

Operating the Mower .......................................................................................................................................4-37

Shutting Down the Implement ..........................................................................................................................4-41

DISCONNECTING THE MOWER FROM THE TRACTOR .............................................................................4-41

MOWER STORAGE ........................................................................................................................................4-43

TRANSPORTING THE TRACTOR AND IMPLEMENT ...................................................................................4-43

Tire and Wheels ...............................................................................................................................................4-45

Transporting on Public Roadways ...................................................................................................................4-45

Hauling the Tractor and Implement ..................................................................................................................4-47

TROUBLE SHOOTING GUIDE .......................................................................................................................4-49

MAINTENANCE SECTION .............................................................................5-1

Lubrication .........................................................................................................................................................5-2

Tongue ...............................................................................................................................................................5-4

CENTER & WING GEARBOXES ......................................................................................................................5-4

DIVIDER GEARBOX ..........................................................................................................................................5-5

DRIVELINES ......................................................................................................................................................5-6

MAIN CV DRIVELINE SAFETY SHIELD (FIGURE Mnt-R-0032) ......................................................................5-7

WING DRIVELINE .............................................................................................................................................5-8

TO DISASSEMBLE UNIVERSAL JOINT .........................................................................................................5-10

TO REASSEMBLE UNIVERSAL JOINT ..........................................................................................................5-11

BLADE SERVICING ........................................................................................................................................5-13

BLADE SHARPENING ....................................................................................................................................5-14

BLADE REMOVAL ...........................................................................................................................................5-14

BLADE CARRIER REMOVAL .........................................................................................................................5-15

BLADE CARRIER INSPECTION .....................................................................................................................5-15

BLADE CARRIER INSTALLATION .................................................................................................................5-16

SLIP CLUTCHES .............................................................................................................................................5-16

TIRES AND WHEELS ......................................................................................................................................5-17

SEASONAL TORQUE LIMITER MAINTENANCE ..........................................................................................5-17

HYDRAULIC HOSES ......................................................................................................................................5-18

SKID SHOES ...................................................................................................................................................5-18

STORAGE .......................................................................................................................................................5-18

PROPER TORQUE FOR FASTENERS ..........................................................................................................5-19

Gearbox Tools For Disassembly and Assembly ..............................................................................................5-20

Disassembly of Divider Gearbox ......................................................................................................................5-21

Assembly of WW75-340 ..................................................................................................................................5-23

RIGHT ANGLE GEARBOX (OUTBOARD) ASSEMBLY & DISASSEMBLY PROCEDURES ..........................5-31

In order to reduce accidents and enhance the safe operation of mowers, Alamo Industrial, in cooperation

with other industry manufacturers has developed the AEM/FEMA Industrial and Agricultural Mower

Safety Practices video and guide book.

The video will familiarize and instruct mower-tractor operators in safe practices when using industrial

and agricultural mowing equipment. It is important that Every Mower Operator be educated in the oper-

ation of their mowing equipment and be able to recognize the potential hazards that can occur while oper-

ating a mower. This video, along with the mower operator’s manual and the warning messages on the

mower, will significantly assist in this important education.

Your Authorized Alamo Industrial Dealer may have shown this video and presented you a DVD Video

when you purchased your mower. If you or any mower operator have not seen this video, Watch the

Video, Read this Operator’s Manual, and Complete the Video Guidebook before operating your new

mower. If you do not understand any of the instructions included in the video or operator’s manual or if

you have any questions concerning safety of operation, contact your supervisor, dealer or Alamo Indus-

trial.

If you would like a VHS video tape of the video, please email AEMV[email protected] or Fax

AEM VHS Video at (830) 372-9529 or mail in a completed copy of the form on the back of this page to

AEM VHS Video 1502 E Walnut Street, Seguin, TX 78155. and request the VHS video version. Please

include your name, mailing address, mower model and serial number.

Every operator should be trained for each piece of equipment (Tractor and Mower), understand the

intended use, and the potential hazards before operating the equipment.

Alamo Industrial Division is willing to provide

one (1) AEM Mower Safety Practices Video

Please Send Me: VHS Format – AEM/FEMA Mower Operator Safety Video

DVD Format – AEM/FEMA Mower Operator Safety Video

Mower Operator’s Manual

AEM Mower Operator’s Safety Manual

Requester Name Phone:

Requester Address:

City

State

Zip Code

Mower Model: Serial Number:

Date Purchased: Dealer Salesperson:

Dealership Name: Dealership Location:

Mail to:

AEM Video Services

1502 E Walnut street

Seguin, TX 78155

Or Fax to:

(830) 372-9529

Or Email to:

AEMV[email protected]

Safety Section 1-1

SAFETY SECTION

SAFETY

Eagle 20 03/09 Safety Section 1-2

SAFETY

General Safety Instructions and Practices

A careful operator is the best operator. Safety is of primary importance to the manufacturer and should be to

the owner/operator. Most accidents can be avoided by being aware of your equipment, your surroundings, and

observing certain precautions. The first section of this manual includes a list of Safety Messages that, if

followed, will help protect the operator and bystanders from injury or death. Read and understand these Safety

Messages before assembling, operating or servicing this Implement. This equipment should only be operated

by those persons who have read the manual, who are responsible and trained, and who know how to do so

responsibly.

The Safety Alert Symbol combined with a Signal Word, as seen below, is used throughout this

manual and on decals which are attached to the equipment. The Safety Alert Symbol means:

“ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!” The Symbol and Signal Word

are intended to warn the owner/operator of impending hazards and the degree of possible injury

faced when operating this equipment.

Indicates an imminently hazardous situation that, if not avoided, WILL result in DEATH OR

VERY SERIOUS INJURY.

Indicates an imminently hazardous situation that, if not avoided, COULD result in DEATH

OR SERIOUS INJURY.

Indicates an imminently hazardous situation that, if not avoided, MAY result in MINOR

INJURY.

Identifies special instructions or procedures that, if not strictly observed, could result in

damage to, or destruction of the machine, attachments or the environment.

NOTE: Identifies points of particular interest for more efficient and convenient operation or

repair.

(SG-1)

Practice all usual and customary safe working precautions and above all---remember safety is

up to YOU

. Only YOU can prevent serious injury or death from unsafe practices.

READ, UNDERSTAND, and FOLLOW the following Safety Messages. Serious injury or

death may occur unless care is taken to follow the warnings and instructions stated in the

Safety Messages. Always use good common sense to avoid hazards.

(SG-2)

Si no lee ingles, pida ayuda a alguien que si lo lea para que le traduzca las

medidas de seguridad.

(SG-3)

SAFETY

Eagle 20 03/09 Safety Section 1-3

SAFETY

Operator Safety Instructions and Practices

Engine Exhaust, some of its constituents, and certain vehicle components contain or emit

chemicals known to the state of California to cause cancer and birth defects or other

reproductive harm.

(SG-30)

Battery posts, terminals and related accessories contain lead and lead compounds,

chemicals known to the state of California to cause cancer, birth defects or other

reproductive harm.

(SG-31)

For your protection while operating or servicing equipment, wear relatively tight and belted

clothing to avoid entanglement in moving parts. Tie up and protect long hair that could

become entangled in machinery. Remove all jewelry including necklaces, rings and

watches which can get caught in machinery or on corners or edges of the equipment.

Serious injury can result from entanglement with the machinery.

(SG-42)

The rotating parts of this machine continue to rotate even after the PTO has been turned off.

The operator should remain in his seat for 60 seconds after the brake has been set, the

PTO disengaged, the tractor turned off, and all evidence of rotation has ceased.

(S3PT-10)

“Wait a minute...Save a life!”

Never crawl under a raised Implement supported solely by the Tractor 3-Point hitch.

Release of the control lever or mechanical failure will result in the Implement falling and

possible injury or death. Always securely block up the Implement before crawling

underneath to perform repairs and service.

(S3PT-19)

N

ever opera

t

e

th

e

T

rac

t

or or

I

mp

l

emen

t

un

til

you

h

ave rea

d

an

d

completely understand this Manual, the Tractor Operator’s Manual, and

each of the Safety Messages found in the Manual or on the Tractor and

Implement. Learn how to stop the tractor engine suddenly in an

emergency. Never allow inexperienced or untrained personnel to

operate the Tractor and Implement without supervision. Make sure the

operator has fully read and understood the manuals prior to operation.

(SG-4)

The operator and all support personnel should wear hard hats, sa

f

ety

shoes, safety glasses, and proper hearing protection at all times for

protection from injury including injury from items that may be thrown by

the equipment.

(SG-16)

SAFETY

Eagle 20 03/09 Safety Section 1-4

SAFETY

PROLONGED EXPOSURE TO LOUD NOISE MAY CAUSE

PERMANENT HEARING LOSS! Tractors with or without an Implement

attached can often be noisy enough to cause permanent hearing loss.

We recommend that you always wear hearing protection if the noise in

the Operator’s position exceeds 80db. Noise over 85db over an

extended period of time will cause severe hearing loss. Noise over 90db

adjacent to the Operator over an extended period of time will cause

permanent or total hearing loss. NOTE: Hearing loss from loud noise

[from tractors, chain saws, radios, and other such sources close to the

ear] is cumulative over a lifetime without hope of natural recovery.

(SG-I7)

Al

ways rea

d

care

f

u

ll

y an

d

comp

l

y

f

u

ll

y w

ith

th

e manu

f

ac

t

urer

’

s

instructions when handling oil, solvents, cleansers, and any other

chemical agent.

(SG-22)

KEEP AWAY FROM ROTATING ELEMENTS to prevent entanglement

and possible serious injury or death.

(SG-24)

Never allow children to play on or around Tractor or Implement. Children can slip or fall off

the Equipment and be injured or killed. Children can cause the Implement to shift or fall

crushing themselves or others.

(SG-25)

NEVER use drugs or alcohol immediately before or while operating the

Tractor and Implement. Drugs and alcohol will affect an operator’s

alertness and coordination and therefore affect the operator’s ability to

operate the equipment safely. Before operating the Tractor or

Implement, an operator on prescription or over-the-counter medication

must consult a medical professional regarding any side effects of the

medication that would hinder their ability to operate the Equipment safely.

NEVER knowingly allow anyone to operate this equipment when their

alertness or coordination is impaired. Serious injury or death to the

operator or others could result if the operator is under the influence of

drugs or alcohol.

(SG-27)

P

ro

l

onge

d

opera

ti

on may cause opera

t

or

b

ore

d

om an

d

f

a

ti

gue a

ff

ec

ti

ng sa

f

e opera

ti

on.

Take scheduled work breaks to help prevent these potentially impaired operating

conditions. Never operate the Implement and Tractor in a fatigued or bored mental state

which impairs proper and safe operation.

(SG-32)

SAFETY

Eagle 20 03/09 Safety Section 1-5

SAFETY

U

se ex

t

reme cau

ti

on w

h

en ge

tti

ng on

t

o

th

e

I

mp

l

emen

t

o per

f

orm repa

i

rs, ma

i

n

t

enance an

d

when removing accumulated material. Only stand on solid flat surfaces to ensure good

footing. Use a ladder or raised stand to access high spots which cannot be reached from

ground level. Slipping and falling can cause serious injury or death.

(SG-33)

Avoid contact with hot sur

f

aces including hydraulic oil tanks, pumps, motors, valves and

hose connections. Relieve hydraulic pressure before performing maintenance or repairs.

Use gloves and eye protection when servicing hot components. Contact with a hot surface

or fluid can cause serious injury from burns or scalding.

(SG-34)

DO NOT operate this Implement on a Tractor that is not properly maintained. Should a

mechanical or Tractor control failure occur while operating, immediately shut down the

Tractor and perform repairs before resuming operation. Serious injury and possible death

could occur from not maintaining this Implement and Tractor in good operating condition.

(SG-36)

Avoid contact with hot surfaces of the engine or muffler. Use gloves and eye protection

when servicing hot components. Contact with a hot surface or fluid can cause serious injury

from burns or scalding.

(SG-38)

Do not put hands or feet under mower decks. Blade Contact can result

in serious injury or even death. Stay away until all motion has stopped

and the decks are securely blocked up.

(SGM-09)

Always keep a careful lookout and use extreme care when working around utility and

municipal obstructions. Never allow the Mower to contact any utility, municipal, or other

type structure. Clearly mark all mowing obstructions and consult local utility providers for

a safe code of operation.

(SPU-5)

Do not operate the implement while wearing loose fitting clothing. Entanglement of th

e

clothing with the rotating elements can result in serious injury or even death. Stay clear o

f

all rotating elements at all times. (SSP-03)

SAFETY

Eagle 20 03/09 Safety Section 1-6

SAFETY

Equipment Operation Safety Instructions and Practices

Repeated or substantial breathing of hazardous dusts, including

crystalline silica, could cause fatal or serious respiratory disease including

silicosis. Concrete, masonry, many types of rock, and various other

materials contain silica sand. California lists respirable crystalline silica as

a substance known to cause cancer. Operation of this equipment under

certain conditions may generate airborne dust particles that could contain

crystalline silica. In those conditions, personal protective equipment

including an appropriate respirator must be used. If excessive dust is

generated, a dust collection or suppression system should also be used

during operation.

(SG-41)

Never leave the Tractor and Implement unattended while the Implement is in the lifted

position. Accidental operation of lifting lever or a hydraulic failure may cause sudden drop

of unit with injury or death by crushing. To properly park the implement when disconnecting

it from the tractor, lower the stand and put the retaining pin securely in place, or put a secure

support under the A-Frame. Lower the implement carefully to the ground. Do not put hands

or feet under lifted components.

(S3PT-1)

U

se ex

t

reme care w

h

en

l

ower

i

ng or un

f

o

ldi

ng

th

e

i

mp

l

emen

t’

s w

i

ngs.

M

a

k

e sure no

bystanders are close by or underneath the wings. Allow ample clearance around the

implement when folding or unfolding the wings. Use extreme caution around buildings or

overhead power lines.

(S3PT-05)

This Implement is wider than the Tractor. Be careful when operating or transporting this

equipment to prevent the Implement from running into or striking sign posts, guard rails,

concrete abutments or other solid objects. Such an impact could cause the Implement and

Tractor to pivot violently resulting in loss of steering control, serious injury, or even death.

Never allow the Implement to contact obstacles.

(S3PT-12)

B

e sure you

h

ave a

d

equa

t

e

k

now

l

e

d

ge o

f

th

e proper

t

y you w

ill

b

e wor

ki

ng on.

T

a

k

e

ti

me

t

o

make yourself aware of any area underground lines or cables. Contact with buried lines o

r

cable could result in serious injury or death. If in doubt about buried utility lines call 811

before digging or 1-800-258-0808.

(SBH-6)

Do not operate Mower if excessive vibration exists. Shut down PTO and the Tractor

engine. Inspect the Mower to determine the source of the vibration. If Mower blades are

missing or damaged replace them immediately. Do not operate the mower until the

blades have been replaced and the Mower operates smoothly. Operating the Mower with

excessive vibration can result in component failure and broken objects to be thrown

outward at very high velocities. To reduce the possibility of property damage, serious injury,

or even death, never allow the Mower to be operated with blades missing.

(SFL-4)

SAFETY

Eagle 20 03/09 Safety Section 1-7

SAFETY

Operate this Equipment only with a Tractor equipped with an approved roll-

over-protective system (ROPS). Always wear seat belts. Serious injury or

even death could result from falling off the tractor--particularly during a turnover

when the operator could be pinned under the ROPS.

(SG-7)

BEFORE leaving the tractor seat, always engage the brake and/or set

the tractor transmission in parking gear, disengage the PTO, stop the

engine, remove the key, and wait for all moving parts to stop. Place the

tractor shift lever into a low range or parking gear to prevent the tractor

from rolling. Never dismount a Tractor that is moving or while the engine

is running. Operate the Tractor controls from the tractor seat only.

(SG-9)

Never allow children or other persons to ride on the Tractor or Implement.

Falling off can result in serious injury or death.

(SG-10)

Never allow children to operate, ride on, or come close to the Tractor or

Implement. Usually, 16-17 year-old children who are mature and

responsible can operate the implement with adult supervision, if they

have read and understand the Operator’s Manuals, been trained in

proper operation of the tractor and Implement, and are physically large

enough to reach and operate the controls easily.

(SG-11)

Do not mount or dismount the Tractor while the tractor is moving. Mount

the Tractor only when the Tractor and all moving parts are completely

stopped.

(SG-12)

Start tractor only when properly seated in the Tractor seat. Starting a

tractor in gear can result in injury or death. Read the Tractor operators

manual for proper starting instructions.

(SG-13)

SAFETY

Eagle 20 03/09 Safety Section 1-8

SAFETY

Do not operate this Equipment with hydraulic oil or fuel leaking. Oil

and fuel are explosive and their presence could present a hazard. Do

not check for leaks with your hand! High-pressure oil streams from

breaks in the line could penetrate the skin and cause tissue damage

including gangrene. To check for a hose leak, SHUT the unit ENGINE

OFF and remove all hydraulic pressure. Wear oil impenetrable gloves,

safety glasses and use Cardboard to check for evidence of oil leaks. If

you suspect a leak, REMOVE the HOSE and have it tested at a Dealer.

If oil does penetrate the skin, have the injury treated immediately by a

physician knowledgeable and skilled in this procedure.

(SG-15)

Never run the Tractor engine in a closed building or without adequate ventilation. The

exhaust fumes can be hazardous to your health.

(SG-23)

Do not exceed the rated PTO speed for the Implement. Excessive PTO speeds can cause

Implement driveline or blade failures resulting in serious injury or death.

(SG-26)

Operate the Tractor and/or Implement controls only while properly seated in the Tractor seat

with the seat belt securely fastened around you. Inadvertent movement of the Tractor or

Implement may cause serious injury or death.

(SG-29)

I

n case o

f

mec

h

an

i

ca

l

diffi

cu

l

ty

d

ur

i

ng operat

i

on, p

l

ace t

h

e transm

i

ss

i

on

i

n t

h

e par

k

position, set the parking brake, shut down all power, including the PTO and the engine and

remove the key. Wait until all rotating motion has stopped before dismounting.

(SG-39)

Do Not operate this equipment in areas where insects such as bees may attack you and/or

cause you to lose control of the equipment. If you must enter in such areas, use a tractor

with an enclosed Cab and close the windows to prevent insects from entering. If a tractor

cab is not available, wear suitable clothing including head, face, and hand protection to

shield you from the insects. Attacking insects can cause you to lose control of the tractor,

which can result in serious injury or death to you or bystanders. Never dismount a moving

tractor.

(SG-40)

Mow only in conditions where you have clear visibility in daylight or with adequate arti

f

icial

lighting. Never mow in darkness or foggy conditions where you cannot clearly see at least

100 yards(90 m) in front and to the sides of the tractor and mower. Make sure that you can

clearly see and identify passersby, steep slopes, ditches, drop-offs, overhead obstructions,

power lines, debris and foreign objects. If you are unable to clearly see these type of items

discontinue mowing.

(SGM-1)

SAFETY

Eagle 20 03/09 Safety Section 1-9

SAFETY

There are obvious and hidden potential hazards in the operation of this

Mower. REMEMBER! This machine is often operated in heavy brush

and in heavy weeds. The Blades of this Mower can throw objects if

shields are not properly installed and maintained. Serious injury or even

death may occur unless care is taken to insure the safety of the operator,

bystanders, or passersby in the area. Do not operate this machine with

anyone in the immediate area. Stop mowing if anyone is within 100 yards

of mower.

(SGM-02)

The rotating parts of this machine have been designed and tested for rugged use.

However, the blades could fail upon impact with heavy, solid objects such as metal guard

rails and concrete structures. Such impact could cause the broken objects to be thrown

outward at very high velocities. To reduce the possibility of property damage, serious

injury, or even death, never allow the cutting blades to contact such obstacles.

(SGM-4)

E

x

t

reme care s

h

ou

ld

b

e

t

a

k

en w

h

en opera

ti

ng near

l

oose o

bj

ec

t

s suc

h

as gravel, rocks, wire, and other debris. Inspect the area before

mowing. Foreign objects should be removed from the site to prevent

machine damage and/or bodily injury or even death. Any objects that

cannot be removed must be clearly marked and carefully avoided by the

operator. Stop mowing immediately if blades strike a foreign object.

Repair all damage and make certain rotor or blade carrier is balanced

before resuming mowing.

(SGM-05)

M

any var

i

e

d

o

bj

ec

t

s, suc

h

as w

i

re, ca

bl

e, rope, or c

h

a

i

ns, can

b

ecome en

t

ang

l

e

d

i

n

th

e

operating parts of the mower head. These items could then swing outside the housing at

greater velocities than the blades. Such a situation is extremely hazardous and could result

in serious injury or even death. Inspect the cutting area for such objects before mowing.

Remove any like object from the site. Never allow the cutting blades to contact such items.

(SGM-06)

M

ow at t

h

e spee

d

t

h

at you can sa

f

e

l

y operate an

d

contro

l

t

h

e tractor an

d

mower.

Th

e

correct mowing speed depends on terrain condition and grass type, density, and height of

cut. Normal ground speed range is from 2 to 5 mph(3-8 kph). Use slow mowing speeds

when operating on or near steep slopes, ditches, drop-offs, overhead obstructions, power

lines, or when debris and foreign objects are to be avoided.

(SGM-07)

Avoid mowing in reverse direction when possible. Check to make sure there are no

persons behind the mower and use extreme care when mowing in reverse. Mow only at a

slow ground speed where you can safely operate and control the tractor and mower.

Never mow an area that you have not inspected and removed debris or foreign material.

(SGM-08)

Do not mow with two machines in the same area except with Cab tractors with the windows

closed.

(SGM-11)

SAFETY

Eagle 20 03/09 Safety Section 1-10

SAFETY

Follow these guidelines to reduce the risk of equipment and grass fires

while operating, servicing, and repairing the Mower and Tractor:

-Equip the Tractor with a fire extinguisher in an accesible location.

-Do Not operate the Mower on a Tractor with an underframe exhaust.

-Do Not smoke or have an open flame near the Mower and Tractor.

-Do Not drive into burning debris or freshly burnt areas.

-Ensure slip clutches are properly adjusted to prevent excessive slippage and plate heating.

-Never allow clippings or debris to collect near drivelines, slip clutches, and gearboxes.

Periodically shut down the Tractor and Mower and clean clippings and collected debris from

the mower deck.

(SGM-12)

Th

e

M

ower

i

s

d

es

i

gne

d

f

or cer

t

a

i

n mow

i

ng app

li

ca

ti

ons an

d

i

s ra

t

e

d

t

o cu

t

up

t

o a spec

ifi

c

size vegetation (see Mower Standard Equipment and Specifications). DO NOT use this

mower to cut vegetation above the Mower’s rated capacity or to cut any type of non-

vegetative material. Only operate this Mower on a properly sized and equipped Tractor.

Operating this Mower in an application for which it is not designed and/or operating the

Mower with the wrong size Tractor can cause Mower component damage and equipment

failure resulting in possible serious injury or death.

(SGM-14)

Do not operate or pull the mower into standing water. When uplift or fan type mower blades

contact water they can be severely deflected downward causing possible failure of blade

resulting in serious boldly injury to the operator or bystanders.

(SGM-15)

Use extreme caution when raising the Mower above ground level. Stop the Blades from

turning when the Mower is raised and passersby are within 100 yards. Raising the

Mower exposes the Cutting Blades which creates a potentially serious hazard and can

cause serious injury by objects thrown from the Blades or by contact with the Blades.

(SPU-1)

SAFETY

Eagle 20 03/09 Safety Section 1-11

SAFETY

Rotary Mowers are capable under adverse conditions of throwing

objects for great distances (300 feet or more) and causing serious injury

or death. Follow safety messages carefully.

STOP MOWING IF PASSERSBY ARE WITHIN 100 YARDS UNLESS:

-Front and Rear Deflectors, Chain Guards, or Bands are installed and in good, workable

condition;

-Mower sections or Wings are running close to and parallel to the ground without exposed

Blades;

-Passersby are outside the existing thrown-object zone;

-All areas have been thoroughly inspected and all foreign material such as rocks, cans,

glass, and general debris has been removed.

NOTE: Where there are grass and weeds high enough to hide debris that could be struck

by the blades, the area should be: inspected and large debris removed, mowed at an

intermediate height, inspected, closely with any remaining debris being removed, and

mowed again at desired final height. (This will also reduce power required to mow, reduce

wear and tear on the Mower drivetrain, spread cut material better, reduce streaking, and

make the final cut more uniform).

(SRM-01)

Do Not attempt to raise or lower the implement wing unless the Implement tongue is

securely attached to the Tractor drawbar. The Implement could tip over and cause

equipment damage and possible serious injury or death. Raise or Lower the mower wing

only while seated in the Tractor operator’s seat with the seat belt securely fastened.

(SRM-2)

Do not turn so sharp or lift mower so high to produce a severe "knocking" of the Driveline

which will cause accelerated wear and breakage of drive train components and could result

in possible injury from the separated Driveline sections.

(SRM-04)

Do not let the Blades turn when the Mower Deck is raised for any

reason, including clearance or for turning. Raising the Mower deck

exposes the Cutting Blades which creates a potentially serious hazard

and could cause serious injury or even death from objects thrown from

the Blades.

(SRM-07)

DO NOT allow any person under a folded wing unless wing is securely

locked up or supported. DO NOT approach the Implement unless the

Tractor is turned off and all motion has ceased. Never work under the

frame work, or any lifted component unless the implement is securely

supported or blocked up. A sudden or inadvertent fall by any of these

components could cause serious injury or even death.

(STI-03)

SAFETY

Eagle 20 03/09 Safety Section 1-12

SAFETY

Connecting or Disconnecting Implement Safety Instructions and

Practices

DO NOT use a PTO adapter to attach a non-matching Implement driveline to a Tractor

PTO. Use of an adapter can double the operating speed of the Implement resulting in

excessive vibration, thrown objects, and blade and implement failure. Adapter use will also

change the working length of the driveline exposing unshielded driveline areas. Serious

bodily injury and/or equipment failure can result from using a PTO adapter. Consult an

authorized dealer for assistance if the Implement driveline does not match the Tractor PTO.

(S3PT-14)

Always shut the Tractor completely down, place the transmission in park, and set the

parking brake before you or anyone else attempts to connect or disconnect the Implement

and Tractor hitches.

(S3PT-15)

Wh

en a

tt

ac

hi

ng

th

e

I

mp

l

emen

t

i

npu

t

d

r

i

ve

li

ne

t

o

th

e

T

rac

t

or

PTO

,

it

i

s

i

mpor

t

an

t

th

a

t

th

e

connecting yoke spring activated locking collar slides freely and the locking balls are seated

securely in the groove on the Tractor PTO shaft. Push and pull the driveline back and forth

several times to ensure it is securely attached. A driveline not attached correctly to the

Tractor PTO shaft could come loose and result in personal injury and damage to the

Implement.

(S3PT-17)

Before operating the Implement, check to make sure the Implement input driveline will not

bottom out or become disengaged. Bottoming out occurs when the inner shaft penetrates

the outer housing until the assembly becomes solid-it can shorten no more. Bottoming out

can cause serious damage to the Tractor PTO by pushing the PTO into the Tractor and

through the support bearings or downward onto the PTO shaft, breaking it off. A broken

driveline can cause personal injury.

(S3PT-18)

Never unhitch without using the Tongue Jack. The Tongue is very heavy. Attempting to lift

the Tongue without using the Tongue Jack could cause strains or other injury. Allowing the

tongue to fall suddenly and unexpectedly could result in crushing injury. Use the Tongue

Jack for lifting the Implement only. Overloading the Tongue Jack can cause failure with

possible serious bodily injury or even death.

(STI-04)

On a fully-assembled unit, do not remove the Wing Retaining Strap until hoses are attached

to the tractor and the Wing Cylinders are filled with oil. Lower the Wings slowly and

carefully. Keep bystanders away during operations.

(STI-05)

Page is loading ...

Alamo Eagle 14 User manual

This manual is also suitable for

Alamo Eagle 14 User manual

Related papers

Other documents