Kenmore 58075123500 Owner's manual

Brand: Kenmore

Model: 58075123500

Category: Split-system air conditioners

Type: Owner's manual

This manual is also suitable for

Owner's Manual

Manual del Propietario

SLIDER/CASEMENTAIRCONDITIONER

HORIZONTAUMARCOACONDICIONADORDEAIRE

Model, Modelo 580. 75063 580. 75123

Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.

www.sears.com

TABLE OF CONTENTS ........................ 2

WARRANTY .............................................. 2

SAFETY ..................................................... 3

Important Safety Instructions ...................... 3

ELECTRICAL REQUIREMENTS .......4

INSTALLING THE POWER CORD.-..4

INSTALLATION ........................................ 5

Installation Requirements ......................... 5

Installation ................................................ 6

Horizontal Sliding Window Installation "-"6

Casement Window Installation...................... 8

Removal From Window ............................... 8

OPERATION ............................................. 9

How and Why ........................................... 9

Normal Sounds ........................................ 9

Capacity and Running Time ..................... 9

Features ................................................. 10

Using the Air Conditioner ....................... 10

Display ................................................... 11

Air Direction Adjustment ......................... 11

Remote Control ...................................... 12

How To Insert Batteries Into Remote Control ...12

MAINTENANCE .....................................13

Air Filter Cleaning ................................... 13

Air Conditioner Cleaning ........................ 13

How to Remove the Front Grille .................. 13

How to Replace the Front Grille .................. 13

TROUBLESHOOTING .........................14

Before Calling for Service ...................... 14

ESPANOL ................................................16

SERVICE NUMBERS ............Back Cover

FULL ONE YEAR WARRANTY ON

ROOM AIR CONDITIONER

For one year from the date of purchase, when this

air conditioner is operated and maintained for

normal room cooling according to instructions in this

owner's manual, Sears will repair this air

conditioner, free of charge, if defective in material or

workmanship.

FULL FIVE-YEAR WARRANTY ON

SEALED REFRIGERATION SYSTEM

For five years from the date of purchase, when this

air conditioner is operated and maintained for

normal room cooling according to instructions in this

owner's manual, Sears will repair the sealed

refrigeration system (consisting of refrigerant,

connecting tubing, and compressor), free of charge,

if defective in material or workmanship.

WARRANTY SERVICE IS AVAILABLE BY

CONTACTING SEARS SERVICE AT

1-800-4-MY-HOME ®.

Warranty coverage applies only to air conditioners

used for non-commercial, private household

purposes.

This warranty applies only while this product is in

use in the United States.

This warranty gives you specific legal rights, and

you may also have other right which vary from state

to state.

Sears, Roebuck and Co., D/817WA,

Hoffman Estates, IL 60179 U.S.A.

-2-

IMPORTANT SAFETY INSTRUCTIONS

The safety instructions below will tell you how to use your room air conditioner to avoid harm to yourself or

damage to your ROOM AIR CONDITIONER.

FOR YOUR SAFETY

Do not store or use gasoline or other flammable

vapors and liquids in the vicinity of this or any other

appliance. Read product labels for flammability and

other warnings.

PREVENT ACCIDENTS

To reduce the risk of fire, electrical shock, or injury

to persons when using your air conditioner, follow

basic precautions, including the following:

• Be sure the electrical service is adequate for the

model you have chosen.

• If the air conditioner is to be installed in a window,

you will probably want to clean both sides of the

glass first. If the window is a triple4rack type with a

screen panel included, you may want to remove

the screen completely before installation.

• Be sure the air conditioner has been securely and

correctly installed according to the separate

installation instructions provided with this manual.

Save this manual and installation instructions for

possible future use in removing or reinstalling this

unit.

• Use gloves when handling the air conditioner.

Be careful to avoid cuts from sharp metal fins on

front and rear coils.

ELECTRICAL INFORMATION

The complete electrical rating of your new room air

conditioner is stated on the serial plate. Refer to the

rating when checking the electrical requirements.

• Be sure the air conditioner is properly grounded.

To minimize shock and fire hazards, proper

grounding is important. The power cord is

equipped with a three-prong grounding plug for

protection against shock hazards.

• Your air conditioner must be plugged into in a

properly grounded wall receptacle. If the wall

receptacle you intend to use is not adequately

grounded or protected by a time delay fuse or

circuit breaker, have a qualified electrician install

the proper receptacle.

• Do not run air conditioner with a protective

covering. This could result in mechanical damage

within the air conditioner.

• Do not use an extension cord or an adapter

plug.

_ Avoid fire hazard or electric shock.

Do not use an extension cord or an adapter plug.

Do not remove any prong from the power cord.

3-prong

grounding

plug

Test \

grounding

type wall

receptacle

Ground

prong

cord

ENERGY SAVING IDEAS

• The capacity of the room air conditioner must fit

the room size for efficient and satisfactory

operation.

• Install the room air conditioner on the shady side

of your home. A window that faces north is best

because it is shaded most of the day.

• Do not block air flow inside with blinds, curtains, or

furniture, or outside with shrubs, enclosures, or

other buildings.

• Close the floor and wall registers and the fireplace

damper so cool air does not escape up the

chimney and into the duct work.

• Keep blinds and drapes in other windows closed

during the sunniest part of the day.

• Clean the air filter as recommended in the

MAINTENANCE section of this manual.

• Proper insulation and weather stripping in your

home will help keep warm air out and cool air in.

• External house shading with trees, plants or

awnings will help reduce the air conditioner's work

load.

• Operate heat producing appliances such as

ranges, washers, dryers, and dishwashers during

-3-

OBSERVEALLLOCALCODESANDORDINANCES.

DONOT,UNDERANY CIRCUMSTANCES,REMOVE

THE POWERSUPPLYCORDGROUNDPRONG.

ELECTRICALGROUNDISREQUIREDONTHIS

APPLIANCE.

For230/208volt 60 Hz, AConly,15Afused and

properlygroundedelectricalsupply isrequired.A time

delayfuseor time delaycircuitbreakeris

recommended.Usea dedicatedcircuit,sewing only

this appliance.

DONOTUSEAN EXTENSIONCORD,

115V-

RECOMMENDEDGROUNDINGMETHOD

Foryourpersonalsafety,thisappliancemustbegrounded.

Thisappliancehasa powersupplycordwitha 3-prong

groundingplug.Tominimizepossibleshockhazard,the

cordmustbepluggedintoamatinggroundingtypewall

receptacleandgroundedinaccordancewiththeNational

ElectricalCode(ANSI/NFPA70)latesteditionandalllocal

codesandordinances,if amatingwallreceptacleisnot

available,it isthepersonalresponsibilityandobligationof

thecustomerto havea properlygrounded3-prongwall

receptacleinstalledbyaqualifiedelectrician.

230V-

Power cord may include acurrent interrupter

device. Atest and reset button is providedon the

plug case. The device should be tested on a

periodic basis byfirst pressingthe TEST button

and thenthe RESET button. Ifthe TEST button

does not trip or if the RESET button will not stay

engaged, discontinue use ofthe air conditioner and

contact a qualified servicetechnician.

NOTE: The shape may be different accordingto its model.

Use Wall Receptacle Power Supply

Standard 125V,

3-wire grounding

receptacle rated

15A, t25V AC

Standard 250V,

3-wiregrounding

receptacle rated

15A,250V AC

Use 15 AMP, time

delay fuse or 15 AMP,

circuit breaker.

Standard 250V,

3-wire grounding Use 20 AMP, time

receptacle rated delay fuse or 20 AMP,

20A, 250V AC circuit breaker.

Electrical Shock Hazard

Plug into a grounded 3 prongoutlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in

death, fire, or electrical shock.

You can choose between the two methods below according to your preference and window sill shape.

USING SLIT "A"

Fasten the stopper using Type A screw, and lead the

power cord out through slit "A'L

Screw(Type A

-4-

USING SLIT "B"

Fasten the stopper using left screw hole, and rotate

properly to lead the power cord out through slit "B'L

INSTALLATION REQUIREMENTS

These instructions are for a horizontal sliding or a

casement window. The electrical outlet must be

within reach of the power cord.

Side louvers and the rear of the air conditioner must

have clear air space to allow enough air flow

through the condenser for heat remove.

The rear of the unit must be outdoors, not inside a

building or garage.

Horizontal sliding window

Casement window

ELECTRICAL SERVICE

Check your available electrical service. The power

supply available must be the same as that shown

on the unit nameplate (found on right side of cabinet).

All models are equipped with a 3-prong service plug

to provide proper service and safe positive

grounding. Do not change plug in any way. Do not

use an adapter plug. If your present wall outlet does

not match your plug, call a qualified electrician to

make the necessary corrections.

SAVE CARTON and this OWNER'S MANUAL for

future reference. The carton is the best way to store

unit during winter or when not in use.

To avoid risk of personalinjury, property damage,

or productdamage due to the weight ofthis

device and sharp edges that may be exposed:

•Air conditioners covered in this manual pose an

excessive weight hazard. Two or morepeople

are neededto move and install the unit.

To prevent injury or strain, use properlifting and

carrying techniques when moving unit.

•Carefully inspect location where air conditioner

will be installed. Be sure itwill support the

weight of the unit over anextended period of

time.

• Handleair conditioner with care. Wear

protective gloves whenever liftingor carrying the

unit. AVOID the sharp metal fins of front and

rear coils.

• Make sure air conditioner does not fall during

installation.

NOTE!

Before using the air conditioner

secure the front grille with two screws

enclosed with the owner's manual.

1. Open the inlet grille downward and

remove the air filter.

2. Fasten the front grille with screws.

3. Reinstall the air filter.

4. Close the inlet grille.

Inlet Grille

-5-

INSTALLATION HARDWARE

NO. NAMEOF PARTS Q'TY

1 Curtain 1

2 Curtain Frame 1

3 Upper Guide 1

4 Side Guide 2

5 Support Bracket 1

6 Bracket 1

7 Leveling bolt & nut 1

8 Bolt 2

9 Nut 2

10 Washer 2

11 Side Guide seal 1

12 Foam Seal Strip 1

13 Window Track Seal 1

14 LBracket 1

15 Screw (Type A) 9

16 Screw (Type B) 3

17 Screw (Type C) 8

REQUIRED TOOLS:

• Tight Fitting gloves

• Standard screwdriver

• Phillips screwdriver

• Pliers

• Sharp knife

• 3!8-inch open end wrench or adjustable wrench

• 1/4-inch hex socket and ratchet

• Tape measure

• Electric drill

• 1/4-inch drill bit

INSTALLATION

Pick a location that will allow the air conditioner to

blow the cold air into the area you want. Windows

used for installation must be strong enough to

support the weight of the air conditioner. Good

installation with special attention to the proper

position of the unit will lessen the chance that

service will be needed.

When cooling more than one room, installation

location is very important. To cool your rooms, cold

air must be blown from the air conditioner in a

straight path.

HORIZONTAL SLIDING

WINDOW INSTALLATION

_1 Loosely attach the Support Bracket to the

bottom of Bracket using Bolts, Washer, and Nuts.

Attach the Leveling bolt and nut. (Fig. 1)

Bolt

Bracket

Washer

Support Br ' Bolt & Nut

FIG. 1

_ Remove protective backing from Window Track

Seal and apply seal to window track (Fig.2)

_J Measure and lightly mark a line 8-1/4 inches

from window jamb Center the Support Bracket

assembly on the window track and fasten with

4 Type C screws.(Fig. 2)

WindowJamb

fjj

JWin_owTrack

i" Seal

FIG. 2

-6-

inPut the Support Bracket against the outside

wall and tighten the Bolts on top of the Bracket.

Adjust the Leveling Bolt so that the air conditioner

will be installed with a very slight tilt (about 1/4")

downward toward the outside for proper drainage.

Tighten the nut. (Fig. 3)

NOTE: DO NOT drill a hole in the bottom of the

base pan The air conditioner is designed to

operate with the bottom of the base pan

approximately half-full of water.

FIG, 3

I_1 Fasten Side Guides to the sides of the Air

Conditioner using 3 Type A screws per Guide.

Start with first screw at middle of Guide. (Fig. 4)

Ir_ Fasten Upper Guide on the top of the Air

Conditioner using 3 Type A screws. (Fig. 4)

Fastening Side Guid_

Side Guide

FIG. 4

I_1 Measure height of window opening from top of

Bracket assembly as shown Fig. 5. Subtract 20-3/4

inches. Mark this measurement on Curtain and cut

the Curtain. (Fig. 5)

FIG. 5

Ir_l Slide Curtain into Curtain Frame. Slide Curtain

Frame assembly into side Guides of the Air

Conditioner cabinet. Make sure Curtain is firmly

enclosed on all sides by the Frame. (Fig. 6)

FIG, 6

I_1 Cut side Guide seal into 2 equal lengths.

Remove protective backing and apply it to the rear

side of cabinet Side Guides, starting just below

Curtain Frame assembly. Pinch off excess length so

seal is even with the bottom of side Guide. (Fig. 7)

weather seal

to side guides

just below edge of

Curtain Frame,

FIG. 7

-7-

_ti] Place Air Conditioner in window opening. It

should sit on Bracket assembly so that Curtain

Frame and cabinet Side Guides are against top and

side window jambs. Mate front of Bracket with Base

Guide attached to the bottom of base pan.

_1_ Drill 1/8 inch holes in window track through the

existing holes on Base Guide. Screw 4 Type C

screws through the holes. (Fig. 8)

_l_lf this is a casement window installation,

proceed to Casement Window Installation. If not,

slide inner window sash firmly against side of the

cabinet.

_'1 Drill 1/8 inch hole in window jamb to align with

the existing holes in the Curtain Frame. Attach

Curtain Frame to window frame with 2 Type B

screws. (Fig. 8)

NOTE= Check all seals and plug any remaining air

gaps with a suitable weatherproof caulk,

_'L_'l]lfthis is casement window

installation,

proceed to Casement Window Installation. If not,

stuff the Foam Seal Strip between the vertical sash

and the window glass, (Fig, 9)

_'_ Attach the L Bracket with a Type B screw. (Fig. 9)

FIG. 9

CASEMENT WINDOW

INSTALLATION

• Installstion procedure isthe ssme as _st descdped in

sIeps 1 through t 1 and step 13 ofthe HorizontalSliding

Window installation.

• Ifthe window openingiswider _an 15-3/4 inchesyou

will need to installa filler panel. Ma_ethis panel from 3/4

inch thick wood and run it the full length ofthe window.

Attach it securely to the window frame and paint it to

proIect it from the weather.

•Since thereis awide variety ofcasement window styles

and sizes, these instructions rosy not be exa_ly suited

to your perticelsr situation. Toensure besI results, have

the work performed by someone skilled in installing

casement window air conditioners.

REMOVAL FROM WINDOW

* Turnoff and unplugthe air conditioner.

* If horizontalslidrngwindow=removethe L Bracket from

window frameand the FoamSeal Strip from betweenthe

windows.

* Remove the Safety Bracket that you installed in Step 12.

* Unscrew the Curtain Frame from the window frame.

* Remove air coadrtionerfrom the window opening.

BECAREFUL NOT TO DROP IT.Once removed,set it

safely out of the way.

* Remove Curtain Frame and Curtain.

* Unscrewthe Side Guidesand UpperGuide.

* Place unitand allassemblyhardware in air cenbit[oaer

shipping carton, and store in a clean, dry place.

*Air conditioners covered in this manual pose an

excessive weight hazard. Two or more people

are needed to moveand install the unit

To prevent injuryor strain, use proper lifting and

carrying techniques when moving unit.

*When handling the air conditioner, be careful to

avoid cuts from sharp metalfins on front and

rear coils.

* Make sure air conditionerdoes notfall during

removal.

-8-

HOW AND WHY

Your room air conditioner provides the following

functions to make hot weather living more

comfortable:

,*Cools and circulates room air.

,*Lowers humidity by removing excess moisture.

,*Filters out summertime dust. dirt. and some

airborne impurities,

The air conditioner performs these functions by

drawing room air through a filter which traps dust

and dirt particles. The air then passes over a

cooling coil which refrigerates the air and removes

excess moisture. The same air is then returned to

the room-cooler, drier, and cleaner, Moisture

removed from the room air is carried to the outside

and evaporated,

Your air conditioner is designed to be easy to

operate and to provide plenty of cooling power,

NORMAL SOUNDS FIG.lO

Aside from the regular fan motor and compressor

sounds coming from your air conditioner, you will

once in a while hear a pinging sound, This is the

result of moisture being picked up from the air inthe

room and thrown against the air conditioner's fan.

This is normal and should not be cause for concern.

Also, do not be alarmed if you hear a slight hissing

or gurgling sound coming from your air conditioner

after it is off. These are normal coolant noises.

CAPACITY AND RUNNING TIME

Proper unit size is important in deciding the desired

comfort for the area you want to cool. An

undersized unit will not have the capability to cool,

leaving the area uncomfortably warm. The proper

size is determined by the number of square feet in

the area to be cooled, indoor and outdoor

temperature and humidity.

Whenever the heat or humidity load is above normal

the air conditioner must run longer and more often

to keep the desired temperature you have selected,

Under heavy heat load conditions the air conditioner

may need to run constantly to keep the temperature

you want,

At times using the MED FAN setting to circulate the

room air may make it comfortable even though the

air is not being cooled, This will decrease your cost

of use.

i ompreasor

The modern high efficiency

compressor may have a h_gh

pitched hum or pulsating

noise that cycles on and off.

Unit Vibration

i Fan The unit may vibrate

You may hear air and make noise

movement from because of poor wall

the fan. or window construction,

Condenael

You may hear drople{s of water hitting

the condenser causing a pinging or

clicking sound,

FIG. 10

FEATURES

4 2

1, Cabin_

2, Air Discharge

3, Vertical Air

Deflector

(Horizontal Louver)

4, Air Intake

(inlet Grille)

5, Air Filter

6, Front Grille

7, Control Panel

8, Power Cord

FIG. 1 1

g. Evaporator Coil

1g. Condenser

11. Compressor

12. Base pan

13. Brace

14. Side Louver

USING THE AIR CONDITIONER

To reduce the risk of fire, electric

shock, or injury to persons, read the important

SAFETY instructions section before operating this

appliance.

To begin operating the air conditioner after

installation, follow these steps:

1. Plug in the air conditioner. (To prevent electrical

hazards, do not use an extension cord or an

adapter plug.)

2. Set the exhaust vent to the CLOSE position.

3. Set the TEMP Control to the coolest setting,

4. Set the MODE control at the highest COOL level,

5. Adjust the louvers for comfortable air flow,

6. Once the room has cooled, adjust the TEMP and

Mode Control to the setting you find most

comfortable.

NOTE : If the air conditioner isturned off, wait 3

minutes before restarting. This allows pressure

inside the compressor to equalize, Failure to wait 3

minutes before restarting may cause inefficient

operation.

If you move the TEMP Control to a warmer, then

immediately back to a cooler setting, the unit will

shut off. Wait 3 minutes before restarting.

VENT CONTROL

The Vent Control allows the air conditioner to

either recimulate inside air (CLOSE) or exhaust

air to the outside (OPEN). (FIG, 12)

* The CLOSE position is used when maximum

cooling is desired. It may also be used for air

recirculation without cooling when the air

conditioner is set in the FAN position.

* The OPEN position removes stale air from the

room and exhausts it to the outside. Fresh air is

drawn into the room through your home's

normal air passages.

* The OPEN or CLOSE position can be used with

any fan selection,

CLOSE-LVENTJLOPEN

FIG. 12

-10-

DISPLAY

- POWER

Toturnthe air cond_ionerON, push thisbutton.To

turnthe airconditioner OFF, pushthe button again.

,,This button _:es priori_ over any other buttons.

,,When you first turn _ on, the uNt is in cool mode,

High 'an speed,Temperature settingat 72"F.

REMOTE CONTROL SIGNAL RE(;

MODE

- Everytime you pushthis button,it will shi"_among

COOL, ENERGY SAVER and FAN.

- ENERGY SAVER

* The'an stops when the compressor stopscooling,

Approximately every3 minutes the fan will turn on and

the unit will checkthe room airto determine ["coolingis

needed.

FAN SPEED

* Everytimeyoupushthisbutton,itadvancesthe

settingasfollows:._HIGH(F3)_.LOW(Ff)_"

MED(F2)_ HIGH(F3)}

TEMPERATURE SETTING

* Usethis button toautomatically controlthe

temperature o"the room,The temperature canbe

setwithina rangeof 60=Fto 86_'Fbyincrementso"

I=F.

When power is restored after an ]

electrical power failure, the unit will begin

to run at its last setting

AIR DIRECTION ADJUSTMENT

HORIZONTAL AIR DIRECTION CONTROL

The horizontal air direction is adjusted by moving

the vertical louvers right and left with your

fingertips. (FIG. 13)

TIMER

- SHUT-OFF TIME

° YOUwillusually use shuI-off time while you sleep.

• With unitrunning,use Timer to set numberof hours until

shuf-off.

• For your sleeping comfort, onceTime is sef, ihe

Ternperature setting will raise2°F sfter 30 rain., and

2°F after snofher 30 rain.

• Every lime you push Timer button, it advances the Timer

settingss follows: 1 Houre 2 Hours _- eft. _- 12 Hours

maximum.

- START TIME

• With unitnor running, use Timer to set numberof hours

before unitsfsrts.

• Every lime you push Timer button, it advances the Timer

setting as follows: 1 Hour _ 2 Hours _ etc. _ 12 Hours

maximum.

VERTICAL AIR DIRECTION CONTROL

The vertical air direction isadjusted by moving the

horizontal louvers up and down with your fingertips.

(FIG, 14)

FIG. 13 FIG. 14

-11

REMOTE CONTROL

Note: The RemoteControl will not operate propedyif

strong light shines on the sensor window of theAir

Conditioner or if there are obstacles be'_een the Remote

Control and _e Air Conditioner.

Every time you push button,you will hear beep sound

from the Air Conditioner.

4 2 5

5, TIMER

- SHUT-OFF TIME

* YOUwill usuallyuse shut-off time while you sleep.

,,With unit running, use Timerto set number of hours

until shut-off.

• Foryour sleeping comfort, once Time is set, the

Temperaturesettingwill raise 2"F after 30 rain, and

2°F after aco_er 30 rain.

• Everytime you push Timer burton, it advances _e

Timersorting as follows: 1Hour_' 2 Hours _. etc._'

12 Hoursmaximum.

- START TIME

• With unitnot running,usetimer to set number of

hours before unit starts.

• Everytime you push Timer burton, it advances _e

Timersorting as follows: 1Hour_' 2 Hours _. etc._'

12 Hoursmaximum.

HOW TO INSERT BATTERIES

INTO REMOTE CONTROL

1. Removethe cuverfrsmthe backuf theremotecurltr_ller.

2. Inserttwo batteries.

• Besure that the (-) and (-) direotionsare correct.

• Be sure that both batteries are new.

3. Re-attachthe cover.

REMOTE CONTROL OPERATIONS

FIG. 15

1. POWER

• Toturn theairconditionerON, push thisbutton.

To turn the air conditioner OFF, push the burton

again.

• Thisburton takes priodtyoveranyother burton.

• When you first turn it on,the unit is in ccol mode, High

fan speed, Temperature se_ing at 72'F.

2. TEMPERATURE SE'VI'ING

• Use this buttontoautomatically control the

temperature of the room.

Thetemperature can be set within a range of60°F to

86°F by increments oft°F.

3. MODE

- Everytime you push this burton, it will shift among

COOL, ENERGY SAVER and FAN.

- ENERGY SAVER

• Thefan stops whenthe compressor stops cooling.

Approximately every 3 minutes _e fan will turn on and

the unit will check the room air to determine if ccoling

is needed.

4, FAN SPEED

- Every time you pushthis burton, it advances the setting

asfollows: {High(F3) -_ Low(F1)," Meal(F2)_' High(F3)}

• Do not use rechargeablebatteries. Such batteries

differ from stendard dry cells inshape, dimensions, and

performance.

• Remove the batteriesfrom the remote controller if the air

conditioner is not goingto be usedfor an extended

length of time.

• In order to prevent discharge, remove the batteries from

the remote control ifthe air conditioner is not goingto be

used foran extended pedod oftime. Keep the remote

control away from extremelyhot or humid places.To

maintain optimal operationof the remote control, the

remote sensor should not be exposedto dtteot sunlight.

• The remote control can be mounted ona wall usingthe

mountable holder.

FIG. 17

-12-

AIR FILTER CLEANING

The Air Filter will become dirty as it removes dust

from the inside air, It should be washed at least

every 2 weeks, If the Air Filter remains full of dust,

the air flow will decrease and the cooling capacity

will be reduced, possibly damaging the unit,

• Pull the inlet grille forward, grasping both tabs,

then pull out the air filter. (FIG. 18)

• Wash the Air Filter under the faucet with warm

water. Be sure to shake off all the water before

replacing the filter. (FIO.t g)

FIG. 18

AIR CONDITIONER CLEANING

Clean the front grille and inlet grille by wipingwith a

cloth dampened in a mild detergent solution. (FI0.20)

The cabinet may be washed with mild soap or

detergent and lukewarm water, then polished with

liquid appliance wax.

To ensure continued peak efficiency, the condenser

coils (outside of the unit) should be checked

periodically and cleaned if they become clogged

with soot or dirt from the atmosphere, Brush or

vacuum exterior coils to remove debris from fins.

FIG. 20

HOWTO REMOVETHE FRONTGRILLE

• Open the inlet grille downward.

• Remove the screw securing the Front Grille,

• Push the grille up from the bottom and pull the top

of the grille away from the case to lift the top tabs

out of their slots,

HOW TO REPLACE THE

FRONT GRILLE

Attach the front grille to the cabinet by inserting the

tabs on the grille into the slots on the front of the

cabinet. Push the grille in until it snaps into place.

FIG. 22

-13_

BEFORE CALLING FOR SERVICE

Check the following list to be sure a service cedl is really necessary. A quick reference to this rne_nual may

help you avoid em unneeded service call.

THE AIR CONDITIONER WILL NOT OPERATE

Check if,,, Then...

TheCurrentinterrupterdovioc istripe& PresstheRESETbutton[ooctedonthe peworcord plug

If81eRESETbutton willnot stayengaged,disocntinueuseofthe

airconditianer andcontact aqualifiedservicetochnician.

Wallplugdi_._nnocted. Pushplugfimdyint_._waitoutlot.

HoucoNss blownor ci_u_tbreakert_pped. RoplcooNso_h 5triodelaytypeorr_cot_rouitbreaker.

PowerisOFF. Push#le powerb_n.

Unitwastumodoffandthenontooquickly. Sotunitoffandwait3 minutesbefor_r_starting.

"TEMPCenb'ols_ wannerthanroomtornperaturo. Sot"[EMPCestaroltea lowernumber.

AIR FROM UNIT DOES NOT FEEL COLD ENOUGH,

Check if,,, Then...

FANSPEEDcotatLOW. PushFANSPEEDb_Lt_ntosotatHI.

"TEMPCenb'ols_ toowarm. Sot"[EMPCestaroltea lowerternpcmtore.

Rocrrltemperaturebelow7O_F(21=C). CoolingmaynotoccurunSImorntornperaturerisesabsso70=F(21°C),

Tember_atur_consingtuhoteuchingovape_terocil, StraighLontubea_',_yfromovaperatercoil.

Iocotedbehindfrontg[itle.

THEAIRCONB110NERCOOLING,BUTROOMISTOOWARM- ICEFORMINGONCOOLINGCOILBEHINDINLETGP&LE

Check if,,, Then...

Out&%_rtornpcn._urebelm,_70°F(21°C). Todefrost_; coil,setth_MODEtoFAN,FANspocdtoHigh.

Air_ltermaybedirty. C[oanairfiltor.RoTorto Maii_Lon_ sectionofownor'srrlanocl.

To_fro_ thecoil,ssttheMODEtoCoc],Fanspocdtohigh,and_;

TEMPCost_l s_ toolow. Ternpoanfareltoa highertemper_atur,_.

"file AR CONBIllONB:IO(X)LI_,, BUTROOMISTOOWARM

Check if,,, Then...

Di_yairfilter- airrns_od. C[oanairfiltor.RoTorIo Ma[i_Lon_ soctbnofownor'srrlanocl.

TEMPC_3ntrolcottoowarm. Sot"[EMPCest_roltea lowert_nporature.

Frontcf unitisblockodbydrape&blinds,furniture,otc. C[oarblockageinfrontcf unit.

Ai_"dist4b_onisr_strictod.

Doors,windows,ro'jisters,otc.open.Coldai_"eco_poc. Cle",_odoors,windows,registers,otc.

Unit_n_ turnodon inhotrocrrl. AJb',_additbr_'_,r_to_rnoves_ -cat_ wals,_ling, I_or,an_fuml,_.

THE AIR CONDITIONER TURNS ON AND OFF RAPIDLY,

Check if,,, Then...

Outsidetemperature[soxtrume[yhot. SetFANSPEEDonHItom[nirnizothococlingIocd.

Unitiscottoanorg!/ssvorrrlodo Approx'rretolyc'_ r,t 3 rrlinulss_e fenwillturnonand_e unitv_l[chock

_herooma'rternper,._t_retodetermineifcoelingisneodcd.Thisisnarm_[

energysscorrteds opera,on.

NOISE WHEN UNIT IS COOLING,

Check if,,, Then...

Soul_doffal__-_ing_ator- frorrlthomoisturenercovals,f_el_. This[snarrnsl_e_ httr_)[dityis high.Clocodsors,v_'ndo_,a_qdrogistor&

Wndswvbin€ion- _or nstalaCon. Referto ns_ laton nstrvcConsorchockw_thnstaer.

WATER DRIPPING INSIDE ROOM WHEN UNIT IS COOLING.

Check if,,, Then...

I Tr_eairocndiConerisirnpmberlyinstallod. I 131tairocnditianersligi_tfytetheeutsideteallowwatord_inage.Referteinst_llatianinstructionsorchock_ installer.

WATER DRIPPING OUTSIDE WHEN UNIT IS COOLING,

Check if,,, Then...

Tr]e unitisremovinglargequant_t[nsofr"_oistur_ Thisisnerma[duringe,_'voly humiddays.

f_rn humidmorn.

-14-

-15-

INDICE DE MATERIAS ............................. 16

GARANT_ ................................................ 16

SEGURIDAD .............................................. 17

Importantesinstrucciones deseguridad-,,-,17

REQUERIMIENTOS ELECTRICOS ......... 18

INSTALACION DEL CABLE ELECTRICA -'18

INSTALACION ........................................... 19

Requistios de ventana .......................... 19

Installaci6n ............................................ 20

Montaje en una ventana de cormdera

horizontal ............................................... 20

Instalacion de ventana con marco .........22

La eliminacion de la ventana ................. 22

OPERACION .............................................. 23

C6mo y por qu6 ..................................... 23

Sonidos normales .................................. 23

Capacidad y tiempo do funcionamiento,-23

Caracterieticae ..................................... 24

Uso del equipo de aire acondicionado--24

Caracteristicae del equipo de aire

acondicionado ....................................... 25

MANTENIMIENTO .................................... 26

Limpieza del filtro del aire ...................... 26

Urnpiezadel equipode aireacondidonado -,--26

CSmo eacar la rejilla frontal ................... 26

CSmo a reemplaza el grille anterior ,..,..26

CORRECCION DE FALLAS ...................... 27

Antesde Llarnarpareservicio...................... 27

PARA PEDIR SERVICIO .......Cubierta Trasera

GARANTIA DE UN ANO POR EL

EQUIPO DE AIRE ACONDICIONADO

DE HABITACI()N

Dumnte un a_o complete a partir de la fecha de

compra, si este equipo de aire acondieionado recibe

mantenimiento y se utiliza para el enfriarniento

normal de habitaei6n seg0n las instrucciones

indicadas en este manual del propietario, Sears

reparar_, gratuitamente este equipo de aire

acondicionado, si tiene alg0n defects en rnateriales

o fabricaci6n.

OARANTIA TOTAL DE CINCO A_IOS

POR EL SISTEMA DE REFRIGERACI()N

HERMETICAMENTE SELLADO

Dumnte cinco a_os a partir de la fecha de compra,

sieste equipo de aire acondicionado recibe

mantenimiento y se utiliza para el enfriarniento

normal de habitaei6n seggn las instrucciones

indicadas en este manual del propietario, Sears

reparar_, gratuitamente el sistema de refrigeraci6n

herrn_ticarnente sellado (qua consiste en el agente

refrigerante, los tubas de cone×i6n y el compresor),

si tiene alg0n defeeto en materiales o fabricaci6n.

EL SERVICIO DE GARANTIA ESTA A SU

DISPOSICION CON SOLO PONERSE EN

CONTACTO EL CENTRO DE SEARS AL

1-SO0-4-MY-HOME _

La proteccion de garantfa cubre unicamente a los

equipos de aire acondicionado usados para usa

domestico y no para uso comereial.

Esta garantfa s61o tiene validez mientras el producto

se est_ usando en los Estados Unidos.

Esta garantfa le da derechos legales especfficos y

usted puede tener otros detaches que varfan de

estado en estado.

Sears, Roebuck and Co., D/817WA,

Hoffman Estates, IL 60179 U.S.A.

-16-

IMPORTANTES INSTRUCCIONES DE SEGURIDAD

Las siguientes instrucciones de seguridad le indicar_n c6mo usar su equipo de sire acondioionado de

habitaoi6n papa evitar da_os pars usted mismo y para su EQUIPO DE AIRE ACONDICIONADO,

POR SU SEGURIDAD

No alrnacene ni use gasolina u otros vapores y

Ifquidos inflamables cerea de _ste o cualquier otro

eleotrodom6stico. Lea las etiquetas de los

productos papa vet si contienen advertencias sobre

el car_cter inflamable de los rnismos y otras

advertencias.

PARA PREVENIR ACCIDENTES

Pars reducir el desgo de incendios, descargas

el6otricas o lesiones personales al usar su equipo

de aire acondicionado, tome las precauciones

b_sioas, entre las que est_n las siguientes:

• Asegkirese de qua la alimentaci6n el6ctrica sea la

apropiada pare el rnodelo qua usted ha elegido.

• $i el equipo de sire acondioionado debe instalarse

en una ventana, a usted probablemente le

conviene limpiar primate arnbos lades del vidrio.

$i la ventana es del tipo de tres paneles con un

panel inoluido de pantalla, le conviene sacar la

ventana completarnente antes de la instalaci6n.

• Asegkirese de qua el equipo de aire

acondicionado ha side instalado correctamente y

con seguridad segL_nse sehala en las

instrucoiones separadas de instalaoi6n que vienen

en este manual. Conserve este manual y las

instrucoiones de instalaoi6n para usarlos

posiblemente en el future al saoar o volver a

instalar esta unidad.

• Use guantes al manejar el equipo de aire

acondicionado, tenga ouidado pare evitar oortadas

con las afiladas aletas met_.licas qua se hallan en

nes frontales y posteriores.

INFORMACION ELECTRICA

En la place de eerie del fabrioante se indica ou_] es

la oapacidad el_ctrios nominal complete de su nuevo

equipo de aim aosndidonado pare habitad6n. Consulte

esta place cuandovaya averific_r los requedmientos

el6ctricos.

• Asegfire_sede que elequipo de sire aosndioionado

tangs unacone_6n osrrecta atierra. Para reduoiral

rnmlrnolosdesgosde descargas el_ctrioss e incendio,

es impor_nteconectar el equipo osrrectamente a tierra,

Elosrd,6nde alimerr_oi6n el_'ioa e_ equipade con

un enchufede _es espigascon osne:,d6na _errapare

protegedecon'_adesgos de desc_rgas el_trioss.

" Su equipo de sire acondidonado debe enohuf_ en

unatoms de osrriente de pared quetenga una osneYJ6n

osnecta atierra. Si la toms de corrierrte de paredque

usted piensausar no _ osnec_de osnec_mente a

•_erm o no est_ protegida conun fusible de acci6n

retardapa o conun irTterruptorde circuito, hagsque un

elec_'icistacalificado le instale laterns de osrriente de

pareden forms correct&

• No posg_ a funcionar el equipo de sire aosndioionado

con unacubierta protectors extedor entire& Estopodrfa

oossionar da_os rrec,_niossder'¢¢odel sire

acondidonado.

• No use uncable de extension ni un enchufe

adeptador.

_ Evrtelospeligrosdeinsendiosy

desosrgasel_;_ioss.No useuncable deexlensi6nni un

enchufesdaptador.No elimineningunade lasespigas

delenchufedelcord,6nde slimentad6nel6ctdca,

Temade corriente

de pared con

cone_i6na tierra.

Pruebs

,_C, able de

alimentsci6n

I cosclsvij a

_ I do_adade

conexi6n s

_] tierra de 3

/ , terminsles,

/ Terminalde

osnexi6n a tierra.

_/ BSjOninguna circunstancia

/' corte, quite o evite el use de

la osnexi6n a tierra de esta

clavijs.

IDEAS PARA AHORRAR ENERGJA

• La capaoidad del equipo de sire acondicionado

debe corresponder al tamafio de la habitaoi6n

pare el funcionamiento eficiente y satisfactorio del

equipo.

• Instale el equipo de sire acondicionado de

habitaci6n en el lade sombreado de su hogar. Una

ventana orientada haoia el norte es la major

porque tiene sombre la mayor parte del d/a.

• No bloquee el flujo de sire hacia el interior oon

persianas, cortinas o muebles; o la parte de

afuera con arbustos, parades u otras

construcoiones.

• Cierre el regulador de tire de la chirnenea, las

rejillas de calefacoi6n del piso y la pared, de tel

mode que el sire fr{o no se esoape ni per la

ohirnenea ni per los oonductos.

• Mantenga las persianas y las oortinas de otras

ventanas oerradas durante la parte m_.s soleada

del dfa.

• Limpie el filtro del sire oomo se recomienda en la

seooi6n "MANTENIM lENTO" de este manual.

• El aislamiento correoto y las juntas herm_,ticas en

puertas y ventanas en su hogar le ayudar_n a

mantener el aire caliente afuera y el aire frfo

adentro.

• AI darle sombre externamente a la ease con

_rboles, plantas o toldos ayudar_, a reducir la

carga de trabajo del equipo de sire acondioionado.

• Opere los aparatos qua produoen calor come, per

ejemplo, homes, lavadoras, secadoras y

lavaplatos durante la parte rn_s frfa del dfa,

-17_

RESPETETODOSLOSCODIGOSY REGLAMENTO&

BAJONINGUNACIRCUNSTANClAC0RTE,QUITE0

EVITEELUS0DELACONEXIONATERRADEESTA

CLAVIJA.

ESTEAPARAT0NECESITASERCONECTADOATIERRA.

8e requiereureaalirnentaci6nel_ctricaCA,adecaadamer_te

conect_daa tierraconun_usiblede15A,de60Hzyde

230/208V,Serecomiendaunfusiblederetardooun

disyunlordeciR:uitoqua_limenlesol{_Tlenleaesteap_r_to,

NOUSECABLEELECTRIC0DEEXTENSION.

METODORECOMENDADODECONEXIONA"nERRA

Persupro_acogL;rid_d_.__ara_d_b_cco_rs_ a_o_.E_

-:paratovie_eequpadeeo_ancabledealimentad_,nyan-:eavij-:de

1_ teTlinaes Pa'ared_ci_-:lT_xinoelpelcjedec_equeel_chico

elcabledebee_ar¢onectadea_a conexi_,ndep-:recconeo_exiSn

-:tierra,yr_ conexi_,ndebeheco_edeacuercoconatiltima

edie6ndelC6digeEl_ctFcol'Jecon-:l(Ar'4SI_I',_FPA70),e_fcoteco_

losc6digosy_gleTentosIce-:leeSinoexileco-:co_exi_,nee

p_r_ad_:_ad_,e clientetienea _e_s_bilcadylaebligeci_nde

nanee_instaler,co"coeec_ricietac_lifcodo,:_"econexi_,ndep_

_dr_:_ad_det_ te_minaesconconex6n_tierra

115V~ 230V~

F / I

Elcablede_limmtad6npcadeincbir_ndiepcaitive

interrupterdecorriente,L_carcae_de[enchufec_enia

can_nborondepr_eb_yottodereinicio.Eldiepcailivo

debecomprobweeperi_dicamenteprcaionando

primateelboi6nTESTydcap_J_eRESET.

Sie[bo'_onTESTnosedescanectaosielb_l_n

RESETnopermanecaactive,saspsndaelusedsIaira

acandicionadoypbngaseanconl_ctocanuntecnica

des_r4cioeualificado,

NOTA: La forma puede ser diferente segdn su modelo.

Utilice el enchufe de [a pared Consume de Energi_

Standard 125V,

enchufe de 3

L'nea.s de

15A, 125V AO Utilice un fusible de

15AMP, o _n

Standard 125V, Int_rrap|or _Je15AMP.

enchufe de 3

L'nea.s de

15A, 125V AO

Standard 250V,

enchufe de 3 Utilice un f_sible _e

L'nea.$ de 20AMP. o _n

20A, 250V AC Int_rrap|or _Je20AMP.

Peligro be chequeel_rico

Conecte en una conex16nde pared de 3 terminale8

No quite la terminalde conexi6n a tierra

No use abap_bores

No use cable el_ctrico de extension

8i nose siguenest_sinstrucciones,puede ocasionarse

la muerte,un incendio oun chequeel_trico.

Puede escogerentre los dos m_todos abajodescritosde acuerdo ala forma del tabureIe de su ventana y su preferencia.

UTILIZANDO LA RANURA "A"

Aprete el obturador usando hoyo do tornillo, y saque

el cable el_.ctricoa trav_.s do la ranura "A'.

UTILIZANDO LA RANURA "B"

Aprete el obtumdor usando el hoyo izquierdo do

tomillo, y gire apropiadamente pare sacar el cable

el_ctrico a tray,s de la ranura "B".

-18-

REQUISTIOS DE VENTANA

Estas Jnstrucoiones son pars una ventana de

corredera horizontal o un marco de ventana.

La salida el6ctrica debe quedar al alcance del cable

de conexi6n.

Para la instalaci6n en una ventana con marco, la

estructura de la ventana y el lateral del edificio

deben ser los adecuados pars sopoltar el peso del

aparato de airs acondicionado.

Ventana de oorredera horizontal

Ventana con marco

SERVICIO ELECTRICO

Cornpruebe cu_l ee la alirnentaci6n el_ctric_que Ilega a

su dornioilio.L_ slirnentaci6n el_ctdca dispanible debe ser

la rnismaque se rnuestraen Isplata del "fsbdcantede la

unidad (que se hslla en el lads dereoho del gabinete de

corriente alterna).

Todos los rnodelos est&n equipadoe con un enchufe de

treseepigas papasurninisImr un sepsis correctsy una

conexi6n a tierra segum y positive. Nocambie el enchufe

de ninguna forrna. No use un enchufe adsptador. Si eu

toma de corriente de pared actual no puede uearee con el

enohu'fedel equips, Ilamea un electdcista calificsdo pars

queefectde Isscorresoiones necssarias.

CONSERVE LA CAJA y este MANUAL DEL

PROPIETARIO pars que le siwa corns referenois en el

futurc. La cajaes la rnejormanem de conservar Isunidad

durante el inviemo o cuando no est& en uso.

Pare evitsrel riesgode lee[onespersonales,dsnosa

su propiedad,o dance al products debido sl peso de

esteequir)oylosf[Iosa que seran exr)uestos:

• El sire asondicionado del que se bahiaen este

manual sfirma peligro de peso exsesivo.

Dos o ross personas se requiere pars movere

instslar Is unidsd. Pars ev[tar her[dasoagstamlento,

use tecni_s apropiadas pare levntary removerla

unidsd.

• Cu[dadossrnenteinspeoc[oneel lugardondeel airs

asondicionadosere puesto.Asegurese que el lugsr

sostengael pesode Is unidsdsebre un par[odo de

tiempo prolsngads.

• Msntengs su sire scondicionadoson cuidsdo. Use

guantesprotectores cusndo levsnteo muevs Is

unidsd, EVlTE lasaletas 'ilosas de mmetalen el

serpectln delsctero y de atres.

• Asegurese que el sire asondicionado nose ca[ga

durante Is [nstalac[on.

NOTE!

Antes de usar el acondicionador de

airs asegure la parrilla delantara con

dos tornillos incluidos con el manual

de owner's.

1. Abra la parrilla de la entrada hacia

abajo y quite el filtro de airs.

2. Sujete la parrilla delantera con los

tornillos.

3. Reinstale el filtro de airs.

4. Oierre la parrilla de la entrada.

Bandejade Entrada

-19_

INSTALACION PIEZAS DE

MONTAJE

NO. r_OBBRELAPARTE CAN'ilDAD

1 Cortina 1

2 Ours superior 1

3 Ours lateral 1

4 Ouide lat_tral 2

5 Soporte de fijaci6n 1

6 Soporte 1

7 Tomille de nivelaci6n y tuerca 1

8 Tomille 2

9 Tuerca 2

10 Amndela 2

11 Junta de gufs lataml 1

12 Burlete de espuma 1

13 Selle del Banda de la ventana 1

14 Soporte de fijaci6n de ventana 1

15 Tomille (ripe A) 9

16 Tomille (ripe B) 3

17 Tomille (ripe C) 8

HERRAMIENTAS REQUERIDAS

,Guantes apmtados

,,Destornillador normal

,,Destornillador Phillips

,,Pinsas

,,Cuchillo filoso

,,Llave inglesa o Ilave abierta de 3/8"

,,Llave hexagonal de cube y trinquete de 1/4

de pulgada

* Cinta para medir

*Taladro electrico

"Broca de taladro de 1/4"

INSTALACION

Escoja un lugar que le permita Ilevar el aire fris al &rea

que desea. Las vestanas que se usen pare la

ins'talaciOndebes tarter la resis'tescia suficiente para

espsrtar el peso del equipsde aire acondicionado. Una

buena instalaci6n con a'tenciOnespecial a la correcta

posici6n de la unidad disminuir& la probabilidad de que

sea necesado efestuar reparaciones.

Cuands se deses enfdar m&s de una habi'taci6n, la

ins'talaciOnes muy impsrtanta puesto que el aire frfs no

dobla esquinas. Para enfriar sus habitaciones, el aire

frfs debe desplazarse desde el equips de aire

acondicionado en una "trayestoria recta.

- 20 -

MONTAJE EN UNA VENTANA

DE CORREDERA HORIZONTAL

E! Colocar sin apretar el soporte a la parte infedor de

la fijaci6n usando los "_rnillos y arandela y tuercas.

Colacar el tomillo y latuerca de nivelaci6n. (Fig. 1)

.._L-...._Tor nillo

A nde,a

Tue a

fijaci6n _ _ FIG 1

I1_ Ouitan la protesciSn del sells de la banda del

ventana y aplique el sells a la banda del ventana.

IR']I Mida y marca auavemente una Ifnea de 8-1/4

pulgadas desde la jamba de la ventana. Centre el

conjunto del soporte en la banda de la ventana y

ajListalo 4 tornillos del tips C (Fig. 2).

8', _sIpulga

Page is loading ...

Kenmore 58075123500 Owner's manual

Brand: Kenmore

Model: 58075123500

Category: Split-system air conditioners

Type: Owner's manual

This manual is also suitable for

Download PDF

report

in other languages

español: Kenmore 58075123500 El manual del propietario

Kenmore 58075123500 Owner's manual

This manual is also suitable for

Kenmore 58075123500 Owner's manual

in other languages

Related papers

Other documents