Craftsman 020606-00 Owner's manual

Brand: Craftsman

Model: 020606-00

Category: High-pressure cleaners

Type: Owner's manual

This manual is also suitable for

580754890

Operator's Manual

T °

3000 PSi MAX* @ 2.4 GPM

2600 PSi @ 2.7 GPM MAX*

PRESSURE WASHER

Model No. 580.754890

WARNING

Before using this product, read this

manual and follow all Safety Rules

and Operating Instructions,

ADVERTENCIA

Antes de utiiizar el producto, lea este

manual y siga todas las Reglas de

Seguridad e Instrucciones de Uso,

,, Safety

,,Assembly

,, Operation

o Maintenance

o Parts

- Espa5ol, p. 36

* Thuspressure washer usrated unaccordance to the Pressure Washer Manufacturers Assocuatuon

(PWMA) standard PW101-2010 (Teshng and Rahng Performance of Pressure Washers)

* Esta hmpuadora a presu6n estA clasuficada conforme a la norma PW101-2010 (comprobacu6n y clasuficacu6n de rendumlento de hmpuadoras

a presu6n) de la Asocuacu6n de fabncantes de bombas a presu6n (Pressure Washer Manufacturers Assocuahon, PWMA)

Sears Brands Management Corporation, Hoffman Estates, IL 60179 U.S.A.

Visit our Craftsman website: www.craftsman.com

Part No 80012100 Rev- (09/03/2014)

WARRANTY ....................................... 2

REPAIR PROTECTION AGREEMENT ................. 2

SAFETY RULES .................................. 3-5

FEATURES AND CONTROLS ........................ 6

ASSEMBLY ..................................... 7-11

OPERATION ................................... 12-15

SPECIFICATIONS ................................. 16

MAINTENANCE ................................ 17-21

STORAGE ........................................ 22

TROUBLESHOOTING .............................. 23

REPLACEMENT PARTS ......................... 24-31

EMISSION CONTROL WARRANTY ............... 32-33

ESPAI'4OL ..................................... 34-59

HOW TO ORDER PARTS .................. BACK PAGE

CRAFTSMAN TWO YEAR FULL WARRANTY

FOR TWO YEARS from the date of purchase, this product is warranted against any defects in material or

workmanship. Defective product will receive free repair or replacement if repair is unavailable.

For warranty coverage details to obtain free repair or replacement, visit the web site: www.craftsman.com/warranty.

This warranty covers ONLY defects in material and workmanship. Warranty coverage does NOT include:

• Expendable items that can wear out from normal use within the warranty period, such as spray guns, hoses,

nozzle extensions, nozzles, spray tips, filters or spark plugs.

Product damage resulting from user attempts at product modification or repair or caused by product

accessories.

Repairs necessary because of accident or failure to operate or maintain the product according to all supplied

instructions.

• Preventive maintenance, or repairs necessary due to improper fuel mixture, contaminated or stale fuel.

This warranty is void if this product is ever used while providing commercial services or if rented to another person.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

Sears Brands Management Corporation, Hoffman Estates, IL 60179

Congratulations on making a smart purchase.

Your new Craftsman@ product is designed and

manufactured for years of dependable operation. But

like all products, it may require repair from time to time.

That's when having a Repair Protection Agreement can

save you money and aggravation.

Here's what the Repair Protection Agreement*

includes:

Expert service by our 10,000 professional repair

specialists

Unlimited service and no charge for parts and

labor on all covered repairs

Product replacement up to $1500 if your covered

product can't be fixed

Discount of 25% from regular price of service

and related installed parts not covered by the

agreement; also, 25% off regular price of preventive

maintenance check

Fast help by phone - we call it Rapid Resolution -

phone support from a Sears representative. Think of

us as a "talking owner's manual".

Once you purchase the Repair Protection Agreement,

a simple phone call is ail it takes for you to schedule

service.You can call anytime day or night, or schedule

a service appointment online.

The Repair Protection Agreement is a risk-free

purchase. If you cancel for any reason during the

product warranty period, we will provide a full refund.

Or, a prorated refund anytime after the product warranty

period expires. Purchase your Repair Protection

Agreement today!

Some limitations and exclusions apply. For prices

and additional information in the U.S.A. call

1=800=827=6655.

* Coverage in Canada varies on some items. For

full details, call Sears Canada at 1=800=361=6665.

Sears installation Service

For Sears professional installation of home appliances,

garage door openers, water heaters, and other

major home items, in the U.S.A. or Canada call

1=800=4=lVlY-HOME®,

Read this manual carefully and become

familiar with your pressure washer. Know its

applications, its limitations, and any hazards

involved.

important Safety information

Safety Symbols and Meanings

Operator's Manual

Slippery Surface

Fire

Toxic Fumes

ElectricalShock

Fall FluidInjection

Explosion Kickback Projectile

Moving Parts Flying Chemical Hot Surface

Objects Burn

The safety alert symbol indicates a potential

personal injury hazard. A signal word (DANGER,

WARNING, or CAUTION) is used with the alert symbol

to designate a degree or level of hazard seriousness. A

safety symbol may be used to represent the type of

hazard. The signal word NOTICE is used to address

practices not related to personal injury.

DANGER indicates a hazard which, if not avoided,

will result in death or serious injury.

WARNING indicates a hazard which, if not avoided,

could result in death or serious injury.

_.' CAUTION indicates a hazard which, if not avoided,

could result in minor or moderate injury.

NOTICE address practices not related to personal

injury.

Z_ WARNING The engine exhaust from this

product contains chemicals known to the State of

California to cause cancer, birth defects, or other

reproductive harm.

WARNING This product contains lead and lead

compounds, known to the State of California to

cause birth defects or other reproductive harm.

Wash your hands after handling this product.

WARNING POISONOUS GAS HAZARD.

Engine exhaust contains carbon monoxide,

a poisonous gas that could kill you in

' minutes.You CANNOT smell it, see it, or

taste it. Even if you do not smell exhaust fumes, you

could still be exposed to carbon monoxide gas.

Some chemicals or detergents could be harmful if

inhaled or ingested, resulting in death, serious injury,

nausea, fainting or poisoning.

• Operate this product ONLY outside far away from

windows, doors and vents to reduce the risk of carbon

monoxide gas from accumulating and potentially being

drawn towards occupied spaces.

• Install battery-operated carbon monoxide alarms or

plug-in carbon monoxide alarms with battery back-up

according to the manufacturer's instructions. Smoke

alarms cannot detect carbon monoxide gas.

• DO NOT run this product inside homes, garages,

basements, crawlspaces, sheds, or other partially-

enc!osed spaces even if using fans or opening doors and

windows for ventilation. Carbon monoxide can quickly

build up in these spaces and can linger for hours, even

after this product has shut off.

• ALWAYS place this product downwind and point the

engine exhaust away from occupied spaces.

If you start to feel sick, dizzy, or weak while using this

3roduct, shut it off and get to fresh air RIGHT AWAY. See a

doctor. You may have carbon monoxide poisoning,

• Use a respirator or mask whenever there is a chance that

vapors may be inhaled when using chemicals.

• Read all instructions with mask so you are certain the

mask will provide the necessary protection against

inhaling harmful vapors when using chemicals.

WARNING Chemical Burn Hazard.

_ hemicais could cause burns resulting in

death or serious injury.

L i

• DONOT use caustic liquid with pressurewasher.

• Use ONLYpressure washersafe detergents/soaps.

Followall manufacturersinstructions.

WARNING Starter cord kickback (rapid

_ etraction) will pull hand and arm toward

engine faster than you can let go which

could cause broken bones, fractures,

bruises, or sprains resulting in serious injury.

• NEVER pull starter cord without first relieving spray gun

pressure.

• When starting engine, pull cord slowly until resistance is

felt and then pull rapidly to avoid kickback.

• After each starting attempt, where engine fails to run,

always point spray gun in safe direction, press red button

and squeeze spray gun trigger to release high pressure.

• Firmly grasp spray gun with both hands when using high

pressure spray to avoid injury when spray gun kicks back.

_.' WARNING Risk of electrocution,

_ ontact with power source could cause

electric shock or burn resulting in death or

serious injury.

• NEVER spray near powersource.

z_ WARNING The high pressure stream of water

that this equipment produces could cut

through skin and its underlying tissues,

resulting in serious injury and possible

amputation.

Spray gun traps high water pressure, even when

engine is stopped and water is disconnected, which

could result in serious injury.

• If cut by fluid, call physician immediately. DO NOT treat as

a simple cut.

• DO NOT allow CHILDREN to operate pressure washer.

• NEVER repair high pressure hose. Replace it.

• NEVER repair leaking connections with sealant of any

kind. Replace o-ring or seal.

• NEVER connect high pressure hose to nozzle extension.

• Keep high pressure hose connected to pump and spray

gun while system is pressurized.

• ALWAYS point spray gun in safe direction, press red

button and squeeze spray gun trigger to release high

pressure, every time you stop engine.

• NEVER aim spray gun at people, animals, or plants.

• DO NOT secure spray gun in open position.

• DO NOT leave spray gun unattended while machine is

running.

• NEVER use a spray gun which does not have a trigger

lock or trigger guard in place and in working order.

• Always be certain spray gun, nozzles and accessories

are correctly attached.

WARNING Fuel and its vapors are extremely

__ flammable and explosive which could. cause burns, fire or explosion

' resulting in death or serious injury.

WHEN ADDING OR DRAINING FUEL

= Turn pressure washer engine OFF and let it cool at least

2 minutes before removing fuel cap. Loosen cap slowly to

relieve pressure in tank.

= Fill or drain fuel tank outdoors.

= DO NOT overfill tank. Allow space for fuel expansion.

= If fuel spills, wait until it evaporates before starting engine.

• Keep fuel away from sparks, open flames, pilot lights,

heat, and other ignition sources.

= Check fuel lines, tank, cap and fittings frequently for

cracks or leaks. Replace if necessary.

= DO NOT light a cigarette or smoke.

WHEN STARTING EQUIPMENT

= Ensuresparkplug, muffler,fuel cap, and aircleaner are inplace

• DO NOT crank engine with spark plug removed.

WHEN OPERATING EQUIPMENT

• DO NOT operate this product inside any building, carport,

porch, mobile equipment, marine applications, or enclosure.

= DO NOT tip engine or equipment at angle which causes

fuel to spill.

= DO NOT spray flammable liquids.

WHEN TRANSPORTING, MOVING OR REPAIRING

EQUIPMENT

= Transport/move/repair with fuel tank EMPTY or with fuel

shutoff valve OFF (0).

• DO NOT tip engine or equipment at angle which causes

fuel to spill.

• Disconnect spark plug wire.

WHEN STORING FUEL OR EUIPMENT WroTHFUEL mNTANK

= Store away from furnaces, stoves, water heaters, clothes

dryers, or other appliances that have pilot light or other

ignition source because they could ignite fuel vapors.

WARNING Exhaust heat/gases could ignite

_ _ combustibles, structuresordamagefuel tank causing a fire, resulting in

death or serious injury.

Contact with muffler area could cause burns

resulting in serious injury.

DO NOT touch hot parts and AVOID hot exhaust gases.

Allow equipment to cool before touching,

• Keep at least 5 ft. (1.5 m) of clearance on all sides of

pressure washer including overhead.

It is a violation of California Public Resource Code,

Section 4442, to use or operate the engine on any forest-

covered, brush-covered, or grass-covered land unless

the exhaust system is equipped with a spark arrester, as

defined in Section 4442, maintained in effective working

order. Other states or federal jurisdictions may have

similar laws.

Contact the original equipment manufacturer, retailer,

or dealer to obtain a spark arrester designed for the

exhaust system installed on this engine.

Replacement parts must be the same and installed in the

same position as the original parts.

_.'WARNINGUseofpressurewashercould

_ create puddles and slipperysurfaces causing you to fall resulting

in death or serious injury.

Kickback from spray gun could cause you to fall

resulting in death or serious injury.

• Operate pressure washer from a stable surface.

• The cleaning area should have adequate slopes and

drainage to reduce the possibility of a fall due to slippery

surfaces.

• Be extremely careful if you must use the pressure washer

from a ladder, scaffolding, or any other similar location.

• Firmly grasp spray gun with both hands when using high

pressure spray to avoid injury when spray gun kicks back.

z_ WARNING Unintentional sparking could cause

/X fire or electric shock resulting indeath or serious injury.

WHEN ADJUSTING OR MAKING REPAIRS TO YOUR

PRESSURE WASHER

• Disconnect the spark plug wire from the spark plug and

place the wire where it cannot contact spark plug.

WHEN TESTING FOR ENGINE SPARK

• Use approved spark plug tester.

• DO NOT check for spark with spark plug removed.

WARNING Starter and other rotating parts

could entangle hands, hair, clothing, or

accessories resulting in serious injury.

• NEVER operate pressure washer without protective

housing or covers.

• DO NOT wear loose clothing, jewelry or anything that

could be caught in the starter or other rotating parts.

• Tie up long hair and remove jewelry.

WARNING Risk of eye or bodily injury.

,/_ Spray could splash back or propel

objects resulting in serious injury.

• Always wear indirect vented (chemical splash) safety

goggles marked to comply with ANSI Z87.1 when using

or in vicinity of this equipment.

• NEVER substitute safety glasses or dry-condition

goggles for indirect vented safety goggles.

• Always wear protective clothing such as a long-sleeved

shirt, long pants and close-toed shoes.

• NEVER operate pressure washer when barefoot or

wearing sandals or shorts.

CAUTION Excessively high operating speeds

could result in minor injury.

Excessively low speeds impose a heavy load.

• DO NOT tamper with governor spring, links or other parts

to increase engine speed. Pressure washer supplies

correct rated pressure and flow when running at

governed speed.

• DO NOT modify pressure washer in any way.

NOTICE High pressure spray could damage fragile

items including glass.

• DONOTpointspraygunatglasswhenusingred(0°)spraytip.

• NEVER aimspray gun at plants.

NOTICE Improper treatment of pressure washer

could damage it and shorten its life.

• If you have questions about intended use, ask dealer or

contact qualified service center.

• NEVER operate units with broken or missing parts, or

without protective housing or covers.

• DO NOT by-pass any safety device on this machine.

• DO NOT tamper with governed speed.

• DO NOT operate pressure washer above rated pressure.

• DO NOT modify pressure washer in any way.

• Before starting pressure washer in cold weather, check all

parts of the equipment to be sure ice has not formed there.

• NEVER move machine by pulling on hoses. Use handle

provided on unit.

• This equipment is designed to be used with Sears

authorized parts ONLY. If equipment is used with parts

that DO NOT comply with minimum specifications, user

assumes all risks and liabilities.

KNOW YOUR PRESSURE WASHER

Read the Operator's Manual and safety ruRes before operating your pressure washer.

Compare the illustrations with your pressure washer to familiarize yourself with the locations of various

controls and adjustments, Save this manual for future reference,

A =Spray Gun -- Controls the application of water onto

cleaning surface with trigger device. Includes trigger lock,

B =Accessory Tray -- Provides convenient storage for

accessories, such as gun, nozzle extension, etc.

C =Spray Tips -- Detergent, 0°, 15° and 40°: for various

high pressure cleaning applications.

D =Fold Down Handle -- Handle and accessory tray fold

flat atop cold engine for space-saving storage.

E =Recoil Starter -- Used for starting the engine manually.

F =Oil Fill/Dipstick -- Check, add and drain engine oil here.

G =Water Inlet -- Connection for garden hose.

H =High Pressure Outlet -- Connection for high pressure

hose.

d =Air Filter i Protects engine by filtering dust and debris

out of intake air.

K - Bottle Bracket -- Cleaning solution bottle fits in wire

form bracket here. Concentrate bottle not included.

M - Engine Switch -- Sets engine in starting mode for recoil

starter and stops a running engine.

N =Project Pro® PerfectMix TM Siphon -- Mixes

concentrate with pressure washer spray.

P =Warning/Operating Instructions Tag -- Identifies

hazards and proper procedure to start/stop pressure

washer.

Q =Fuel Tank -- Fill tank with regular unleaded fuel. Always

leave room for fuel expansion.

R =High Pressure Hose -- Connect one end to water pump

and the other end to spray gun.

S =Nozzle Extension with Quick Connect -- Allows you to

switch between four different spray tips.

Items Not Shown:

Pump -- Develops high pressure.

Automatic Cool Down System -- Cycles water through

pump when water reaches 125°-155°E Warm water will

discharge from pump onto ground. This system prevents

internal pump damage.

Identification Label i Provides model and serial number of

pressure washer. Please have these readily available if calling

for assistance.

Your pressure washer requires some assembly and is

ready for use only after it has been properly serviced

with the recommended oil and fuel.

If you have any problems with the assembly of

your pressure washer, please call the pressure

washer helpline at 1=800=222=3136.

UNPACK THE PRESSURE WASHER

1. Remove everything from carton except pressure

washer,

2. Open carton completely by cutting each corner

from top to bottom,

ASSEMBLING PRESSURE WASHER

Your Craftsman pressure washer will need assembly

before operation:

1. Fill out and send in registration card.

2. Attach handle and accessory tray.

3. Connect detergent siphon hose to pump.

4. Add oii to engine crankcase.

5. Add fuel to fuel tank.

6. Connect pressure hose to spray gun and pump.

7. Connect water supply to pump.

8. Attach nozzle extension to spray gun.

3. Remove pressure washer from carton.

CARTON CONTENTS

Check all contents. If any parts are missing or

damaged, call the pressure washer helpline at

1=800=222=3136.

, Main Unit

• Handle

• Accessory Tray with Hose Wrap

• High Pressure Hose

• Spray Gun

• Nozzle Extension with Quick Connect Fitting

• Oil Pouch

9. Select/attach quick connect spray tip to nozzle

extension.

Attach Handle and Accessory Tray

1. Place handle (A) onto handle supports connected

to main unit, Make sure holes in handle align with

holes on handle supports,

Bottle Bracket Wireform

PerfectMix Siphoning Unit/Hose

Parts Bag (which includes the following):

Operator's Manual

Owner's Registration Card

Bag containing 4 Multi-Colored Quick Connect

Spray Tips

Handle Fastening Hardware Kit (which includes):

Handle Bolts (2)

Carriage Bolt

Plastic Knobs for Handle (2)

Plastic Knob

2. Insert handle carriage bolts (B) through holes from

inside of unit and attach a plastic knob (C) from

outside of unit. Tighten by hand.

NOTICE By loosening both knobs to the middle

section of the attachment bolt, the upper handle can

fold forward to store flat atop the cold engine. DO NOT

fold the handle down while the engine is hot.

3. Insert rubber straps (D) through slots (E) in back of

accessory tray and pull tight from front.

Tree Clips (4)

Become familiar with each piece before assembling

the pressure washer. Identify all contents with the

illustration on page 6. If any parts are missing or

damaged, call the pressure washer helpline at

1=800=222=3136.

Place accessory tray (A) over holes (B) on handle

(viewing from front of unit), Push the tree clips

accessory tray,

5, Insert spray tips and other supplied accessories in

spaces provided in accessory tray, See How to Use

Accessory Tray,

6, Place bottle bracket (D) facing outside over hole in

handle support, Secure bottle bracket with carriage

bolt (E) and plastic knob (F), Tighten by hand,

Project Pro@ Perfect Mix TM Siphon

1, Attach the tube end of the blue PerfectMix Siphon

(G) to the barbed tube fitting (H) on the pump,

2, Place Perfect Mix bottle (J) (not included) in

wireform bracket on handle,

3, Remove cap from bottle and insert Perfect Mix

Siphon (G), Screw siphon unit to top of bottle,

NOTICE Use clip (K) on cap to snap siphon to wire

form bracket when siphon is not in a concentrate bottle,

Add Engine Oil

1. Place pressure washer on a flat, level surface.

2. Clean area around oil fill and remove yellow oii fiil

cap/dipstick.

3. Hold neck of supplied oil pouch and remove cap.

4. Slowly pour contents of oii pouch into oil fill

opening. Checking oil level frequently, fiil to FULL

mark (top hole) on dipstick.

I ' ]

_'_'

NOTICE Pause to permit oil to settle. Wipe dipstick

clean each time oil level is checked. DO NOT overfill.

NOTICE Improper treatment of pressure washer

could damage it and shorten its life.

• DO NOT attempt to crank or startthe engine before ithas

been properly servicedwith the recommendedoil.This

could result in an engine failure.

5. Replace oii fiil cap/dipstick and fully tighten.

Add Fuel

Fuel must meet these requirements:

• Clean, fresh, unleaded gasoline.

• A minimum of 87 octane/87 AKI (91 RON). For

high altitude use, see High Altitude.

• Gasoline with up to 10% ethanol (gasohol) is

acceptable.

._.'WARNING Fuel and its vapors are extremely

_ flammable and explosive which could

cause burns, fire or explosion

resulting in death or serious injury.

WHEN ADDING FUEL

• Turn pressure washer engine OFF and let it cool at least

2 minutes before removing fuel cap. Loosen cap slowly to

relieve pressure in tank.

• Fill fuel tank outdoors.

• DO NOT overfill tank. Allow space for fuel expansion.

• If fuel spills, wait until it evaporates before starting engine.

• Keep fuel away from sparks, open flames, pilot lights,

heat, and other ignition sources.

• Check fuel lines, tank, cap and fittings frequently for

cracks or leaks. Replace if necessary.

• DO NOT light a cigarette or smoke.

NOTICE Use of unapproved fuels could damage

generator and voids warranty.

• DO NOTuse unapprovedgasolinesuch as E15and E85.

• DO NOT mixoil in gasolineor modifyengine to run on

alternatefuels.

To protect the fuel system from gum formation, mix in a

fuel stabilizer when adding fuel. See Storage. Ali fuel is

not the same. If you experience starting or performance

problems after using fuel, switch to a different fuel

provider or change brands. This engine is certified to

operate on gasoline. The emission control system for

this engine is EM (Engine Modifications).

1. Clean area around fuel fill cap, remove cap.

2. Slowly add regular unleaded fuel (A) to fuel

tank (B). Be careful not to overfill. To allow for fuel

expansion, do not fiil above the bottom of the fuel

tank neck.

N NNNNNNNNNN

N NNNNNNNNNN N

3. Install fuel cap and wait for any spilled fuel to

evaporate.

CAUTION! Alcohol-blended fuels (called gasohol,

ethanol or methanol) can attract moisture, which leads

to separation and formation of acids during storage.

Acidic gas can damage the fuel system of an engine

while in storage.

To avoid engine problems, the fuel system should be

treated with a fuel preserver or emptied before storage

of 30 days or longer. If adding a fuel preserver, fill the

fuel tank with fresh fuel. If only partially filled, air in the

tank will promote fuel deterioration during storage. If

fuel preserver is not used, drain the fuel tank, start the

engine and let it run until the fuel lines and carburetor

are empty. Use fresh fuel next season. See Storage for

additional information.

NEVER use engine or carburetor cleaner products in

the fuel tank as permanent damage may occur.

High Altitude

At altitudes over 5,000 ft. (1524 m), a minimum

85 octane / 85 AKI (89 RON) gasoline is acceptable. To

remain emissions compliant, high altitude adjustment is

required. Operation without this adjustment will cause

decreased performance, increased fuel consumption,

and increased emissions. See a qualified Sears dealer

for high altitude adjustment information. Operation of

the engine at altitudes below 2,500 ft. (762 m) with the

high altitude kit is not recommended.

Lubricate O=Rings

Lubrication of o-rings is extremely important for

installation and operation. The use of a lubricant

(petroleum or synthetic grease) during assembly helps

seat o-rings properly and provides an improved seal. It

also helps protect the o-ring from damage by abrasion,

pinching or cutting and extends the life of the o-ring.

NOTICE ALWAYS apply a small amount of lubricant

on o-rings prior to assembling the garden hose to the

pump (A), high pressure hose (B), spray gun (C), and

nozzle extension (D).

Lubricate all connections shown below, following

these instructions:

1. Inspect and clean connecting surfaces prior to

lubrication and assembly.

2. Use lubricants sparingly during assembly; a light

film is all that is required.

3. Use a small brush or cotton swab to apply grease

directly to o-rings where they are not accessible

(QC fitting, M22 fitting).

Connect Hose and Water Supply to Pump 4. Run water through garden hose for 30 seconds to

flush it of debris. Turn off water.

NOTICE DO NOT run the pump without the water

supply connected and turned on.

• Damage to equipment resultingfrom failureto follow this

instruction willvoid warranty.

NOTICE Remove and discard the shipping caps from

the pump's high pressure outlet and water inlet before

attaching hoses.

1. Uncoil high pressure hose and attach one end of

hose to base of spray gun. Tighten by hand.

WARNING The high pressure stream of water

that this equipment produces could cut

through skin and its underlying tissues,

resulting in serious injury and possible

amputation.

• NEVER connect high pressure hoseto nozzle extension.

• Keep high pressure hose connectedto pump and spray

gun while systemis pressurized.

• Alwaysbe certain spray gun, nozzlesand accessories

are correctly attached.

2. Attach other end of high pressure hose to high

pressure outlet on pump. Tighten by hand.

3. Before connecting garden hose to water inlet,

inspect inlet screen (A). Clean screen if it contains

debris or have it replaced if damaged. DO NOT run

pressure washer if inlet screen is damaged or

missing,

NOTICE DO NOT siphon standing water for the water

supply. Use ONLY cold water (less than 100°F).

NOTICE Using a One Way Valve (vacuum breaker or

check valve) at pump inlet could cause pump or inlet

connector damage.

• There MUST be at least 10 ft.(3 m)of unrestricted garden

hosebetween the pressurewasher inlet and any device,

such asa vacuumbreakeror check valve.

• Damageto equipment resultingfrom failureto followthis

instructionwill voidwarranty.

5. Connect garden hose (not to exceed 50 ft. in

length) to water inlet. Tighten by hand.

z_ WARNING Risk of eye injury.

_ pray could splash back or propel objects

resulting in serious injury.

* Always wear indirect vented (chemical splash) safety

goggles marked to comply with ANSI Z87.1 when using

or in vicinity of this equipment.

* NEVER substitute safety glasses or dry-condition goggles

for indirect vented safety goggles.

6. Turn ON the water, press red button (B) on the gun

and squeeze the trigger to purge the pump system of

air and impurities.

Checklist Before Starting Engine

Review the unit to ensure you have performed all of the

following:

1. Be sure to read Safety Rules and Operation

sections before using the pressure washer.

2. Make sure handle is in place and secure.

3. Check that oil has been added to proper level in

engine crankcase.

4. Add proper fuel to fuel tank.

5. Check for proper hose connections (high pressure

and water supply) and that there are no kinks, cuts,

or damage to the high pressure hose.

6. Provide proper water supply (not to exceed 100°F).

HOW TO USE YOUR PRESSURE

WASHER

if you have any problems operating your pressure

washer, please call the pressure washer helpline at

1=800=222=3136,

Pressure Washer Location

Carbon Monoxide Poisoning

A_ WARNING POISONOUS GAS HAZARD, Engine

_ xhaust contains carbon monoxide, a

poisonous gas that could kill you in minutes,

You CANNOT smell it, see it, or taste it, Even

if you do not smell exhaust fumes, you could stiil be

exposed to carbon monoxide gas,

• Operate this product ONLY outside far away from

windows, doors and vents to reduce the risk of carbon

monoxide gas from accumulating and potentially being

drawn towards occupied spaces.

• Install battery-operated carbon monoxide alarms or

plug-in carbon monoxide alarms with battery back-up

according to the manufacturer's instructions. Smoke

alarms cannot detect carbon monoxide gas.

• DO NOT run this product inside homes, garages,

basements, crawlspaces, sheds, or other partially-

enclosed spaces even if using fans or opening doors and

windows for ventilation. Carbon monoxide can quickly

build up in these spaces and can linger for hours, even

after this product has shut off.

• ALWAYS place this product downwind and point the

engine exhaust away from occupied spaces.

If you start to feel sick, dizzy, or weak while using this

3roduct, shut it off and get to fresh air RIGHT AWAY. See a

doctor. You may have carbon monoxide poisoning.

To Start Your Pressure Washer

To start your engine-powered pressure washer for the

first time, follow these instructions step-by-step. This

information also applies whenever you start the engine

after you have let the pressure washer sit idle for at

least a day.

1. Place pressure washer outside near an water source

capable of supplying water at a flow rate greater

than 3.7 gallons per minute and no less than 20 PSI

at pressure washer end of garden hose.

2. Check that high pressure hose is tightly connected to

spray gun and pump. See Assembly for illustrations.

3. Make sure unit is in a level position.

4. Connect garden hose to water inlet on pressure

washer pump.

NOTICE DO NOT run the pump without the water

supply connected and turned on,

• Damageto equipment resultingfrom failureto followthis

instructionwill voidwarranty.

Turn ON the water, press red button on the gun and

squeeze the trigger to purge the pump system of air

and impurities.

Attach nozzle extension to spray gun. Tighten by hand.

Pull back on collar of nozzle extension, insert spray

tip and release collar. Tug on spray tip to make sure

it is securely in place. See How to Use Spray Tips.

Exhaust Port

Pointed away from

occupied spaces

Risk of Fire Clearances

z_ WARNING Exhaust heat/gases could ignite

/_ combustibles, structuresor damage fuel tank

causing a fire, resulting in death or serious injury.

• Keep at least 5 ft. (1.5m) clearance on all sides of

pressurewasher includingoverhead.

Push engine rocker switch (A) to ON (I) position.

NOTICE Before starting the pressure washer, be sure

,ou are wearing safety goggles as described below.

/_ WARNING Risk of eye injury,

Spray could splash back or propel objects

, resulting in serious injury,

• Always wear indirect vented (chemical splash) safety

goggles marked to comply with ANSI Z87.1 when using or

in vicinity of this equipment.

• NEVER substitute safety glasses or dry-condition goggles

for indirect vented safety goggles.

NOTICE This unit is equipped with a ReadyStart®

engine. A ReadyStart engine means there is no priming

or choking required.

9. When starting engine, position yourself as

recommended and grasp starter grip handle and

pull slowly until you feel some resistance. Then pull

rapidly to start engine.

',, _'

, ,iI

I i _ ,iI

,,,_-_,v,I',_

• ]1 I

I1' " o i ,_

-4 J

_. WARNING Starter cord kickback (rapid

retraction) will pull hand and arm toward

, engine faster than you can let go which

could cause broken bones, fractures,

bruises, or sprains resulting in serious injury.

• NEVER pull starter cord without first relieving spray gun

pressure.

• When starting engine, pull cord slowly until resistance is

felt and then pull rapidly to avoid kickback.

• After each starting attempt, where engine fails to run,

always point spray gun in safe direction, press red button

and squeeze spray gun trigger to release high pressure.

• Firmly grasp spray gun with both hands when using high

pressure spray to avoid injury when spray gun kicks back.

0. Return recoii starter slowly. DO NOT let rope "snap

back" against starter.

11. Point spray gun in a safe direction, push the red

button to release the trigger lock, and pull the trigger.

WARNING The high pressure stream of water that

this equipment produces could cut through

skin and its underlying tissues, resulting in

serious injury and possible amputation.

Spray gun traps high water pressure, even when

engine is stopped and water is disconnected, which

could result in serious injury.

• DO NOT allow CHILDREN to operate pressure washer.

• Keep high pressure hose connected to pump and spray

gun while system is pressurized.

• NEVER aim spray gun at people, animals, or plants.

• DO NOT secure spray gun in open position.

• DO NOT leave spray gun unattended while machine is

running•

• NEVER use a spray gun which does not have a trigger

lock or trigger guard in place and in working order.

• Always be certain spray gun, nozzles and accessories

are correctly attached.

WARNING Exhaust heat/gases could ignite

_ _ combustibles, structuresordamage

fuei tank causing a fire, resulting in

death or serious injury.

Contact with muffler area could cause burns

resulting in serious injury.

DO NOT touch hot parts and AVOID hot exhaust gases.

Allow equipment to cool before touching.

Keep at least 5 ft. (1.5 m) of clearance on all sides of

pressure washer including overhead.

It is a violation of California Public Resource Code,

Section 4442, to use or operate the engine on any forest-

covered, brush-covered, or grass-covered land unless

the exhaust system is equipped with a spark arrester, as

defined in Section 4442, maintained in effective working

order. Other states or federal jurisdictions may have

similar laws.

Contact the original equipment manufacturer, retailer, or

dealer to obtain a spark arrester designed for the exhaust

system installed on this engine.

Replacement parts must be the same and installed in the

same position as the original parts.

How to Stop Your Pressure Washer

1. Release spray gun trigger and let engine idle for

two minutes.

Push engine rocker switch to OFF (0) position.

ALWAYS point spray gun in a safe direction,

push red button and squeeze spray gun trigger to

release retained high water pressure,

WARNING The high pressure stream of water that

this equipment produces could cut through

skin and its underlying tissues, resulting in

' serious injury and possible amputation.

Spray gun traps high water pressure, even when

engine is stopped and water is disconnected, which

could result in serious injury.

Keep high pressure hoseconnected to pump and spray

gun while systemis pressurized.

ALWAYSpoint spraygun in safe direction, press red

button and squeeze spray gun triggerto release high

pressure,everytime youstop engine.

How to Use Accessory Tray

The unit is equipped with an accessory tray with

places to store your spray gun, nozzle extension, high

pressure hose and spray tips.

1. Place spray gun in wide groove on accessory tray

as shown. Pull rubber strap tight around spray gun

and place hole in strap over tab on accessory tray.

i II .y . ,, '

ll,/'z_ _ _ iL,

-/',, ",, i r_--_-_.-

'_¢-_ --h_ '" _"

\"_/"

2. Place nozzle extension in narrow groove on

accessory tray. Pull rubber strap tight around

nozzle extension and place hole in strap over tab

on accessory tray.

3. Insert multi-colored spray tips in holes provided on

front of accessory tray.

4. Place one end of high pressure hose in groove at

top of accessory tray and wrap high pressure hose

around hooks as shown.

How to Use Spray Tips

The quick-connect on the nozzle extension allows you

to switch between four different quick connect spray

tips. Spray tips can be changed while pressure washer

is running once spray gun trigger is locked. The spray

tips vary the spray pattern as shown.

Follow these instructions to change spray tips:

1. Pull back collar on quick-connect and pull current

spray tip off. Store spray tips in holder provided on

the accessory tray.

_.' WARNING The high pressure stream of water

that this equipment produces could cut

through skin and its underlying tissues,

resulting in serious injury and possible

amputation.

• NEVER changespray patternswithout thetrigger locked

on the spray gun.

• DO NOTtwist spraytips while spraying.

Select desired spray tip:

Low Pressure

Black

Use to apply

detergent

High Pressure

40 ° White 15°Yellow 0° Red

2600 PSi 2600 PSi 3000 PSi

2.7 GPM 2.5 GPM 2.4 GPM

For delicate rinse, for gentle cleaning of

cars trucks, boats, RV's, patio furniture, lawn

equipment, etc., select white 40° spray tip.

For general rinsing, ideal for most all purpose

cleaning such as home siding, brick patios,

wood decks, driveways and sidewalks, garage

floors, etc., select yellow 15° spray tip.

For maximum rinsing, for stubborn or hard to

reach surface such as second story surfaces,

paint removal, oil stains, rust removal or other

stubborn substances (tar, gum, grease, wax,

etc.), select red 0° spray tip.

To apply detergent, applies project specific

cleaners to help break down stubborn dirt and

grime on a variety of surfaces, select black

detergent spray tip.

Pull back on collar, insert new spray tip and release

collar. Tug on spray tip to make sure it is securely in

place.

Usage Tips

For most effective cleaning, keep spray tip from

8 to 24 inches (20 to 61 cm) away from cleaning

surface.

If you get spray tip too close, especially using a

high pressure spray tip, you may damage surface

being cleaned.

Do Not get closer than 6 inches (15 cm) when

cleaning tires.

Cleaning and Applying Detergent

WARNING Chemical Burn Hazard.

,_, Chemicals could cause burns resulting in

death or serious injury.

• DO NOT usecaustic liquidwith pressurewasher.

• Use ONLYpressurewasher safe detergents/soaps.

Follow all manufacturersinstructions.

To apply detergent, follow these steps:

To apply undiluted detergent using the blue PerfectMix

siphon, follow these steps:

1, Review use of spray tips,,

2, Attach PerfectMix siphon hose to pump and

PerfectMix concentrate bottle,

NOTICE Use standard detergent siphon hose &

filter kit, available at Sears retail item 75180, to apply

standard detergents. Detergent siphon hose & filter kit

is available as an optional accessory. Itis not included

with the pressure washer.

NOTICE Contact with the hot muffler could damage

detergent siphoning tube.

• When inserting the siphon into a detergent solution bottle,

route the tube so as to keep it from inadvertently contacting

the hot muffler.

3. Make sure black detergent spray tip is installed.

NOTICE Detergent cannot be applied with the high

pressure spray tips (White, Yellow or Red).

4. Make sure garden hose is connected to water inlet.

Check that high pressure hose is connected to

spray gun and pump. Turn on water.

NOTICE You must attach all hoses before you start

the engine.

• Starting the engine without all the hoses connected and

without the water turned ON could damage the pump.

• Damage to equipment resulting from failure to follow this

instruction will void warranty.

Start engine following instructions How to Start

Your Pressure Washer.

Apply detergent to a dry surface, starting at lower

portion of area to be washed and work upward,

using long, even, overlapping strokes.

Allow detergent to "soak in" for 3-5 minutes before

washing and rinsing. Reapply as needed to prevent

surface from drying. DO NOT allow detergent to dry

on (prevents streaking).

Pressure Washer Rinsing

For Rinsing:

1. Remove black detergent spray tip from nozzle

extension.

2. Select and install desired high pressure spray tip

following instructions How to Use Spray Tips.

3. Keep the spray gun a safe distance from the area

you plan to spray.

A_WARNING Kickback from spray gun could

_ ause you to fall resulting in death or serious

injury.

• Operate pressure washer from a stable surface.

• Be extremely careful if you must use the pressure washer

from a ladder, scaffolding, or any other similar location.

• Firmly grasp spray gun with both hands when using high

pressure spray to avoid injury when spray gun kicks back.

4. Apply a high pressure spray to a small area, then

check the surface for damage. If no damage is

found, it is okay to continue cleaning.

5. Start at the top of the area to be rinsed, working

down with same overlapping strokes as you used

for washing and applying detergent.

Automatic Cool Down System (Thermal

Relief)

ifyou run the engine on your pressure washer for

3-5 minutes without pressing the trigger on the

spray gun, circulating water in the pump can reach

temperatures above 125°R The system engages to cool

the pump by discharging the warm water onto the

ground,

ENGINE TECHNICAL iNFORMATiON PRODUCT SPECIFICATIONS

This is a single cylinder, overhead valve (OHV), air

cooled engine. In the State of California, Model 120000

engines are certified by the California Air Resources

Board to meet emissions standards for 125 hours.

Such certification does not grant the purchaser, owner

or operator of this engine any additional warranties with

respect to the performance or operational life of this

engine. The engine is warranted solely according to the

product and emissions warranties stated elsewhere in

this manual.

Power Ratings

The gross power rating for individual gasoline engine

models is labeled in accordance with SAE (Society

of Automotive Engineers) code J1940 Small Engine

Power & Torque Rating Procedure, and is rated in

accordance with SAE J1995. Torque values are derived

at 2600 RPM for those engines with "rpm" called out

on the label and 3060 RPM for all others; horsepower

values are derived at 3600 RPM. The gross power

curves can be viewed at www.BRIGGSandSTRATTON.

COM. Net power values are taken with exhaust and

air cleaner installed whereas gross power values are

collected without these attachments. Actual gross

engine power will be higher than net engine power and

is affected by, among other things, ambient operating

conditions and engine-to-engine variability. Given the

wide array of products on which engines are placed,

the gasoline engine may not develop the rated gross

power when used in a given piece of power equipment.

This difference is due to a variety of factors including,

but not limited to, the variety of engine components (air

cleaner, exhaust, charging, cooling, carburetor, fuel

pump, etc.), application limitations, ambient operating

conditions (temperature, humidity, altitude), and

engine-to engine variability. Due to manufacturing and

capacity limitations, Briggs & Stratton may substitute an

engine of higher rated power for this engine.

Pressure Washer Specifications

Max Outlet Pressure .................... 3000 PSi*

Max Flow Rate ......................... 2.7 GPM

Detergent Mix .................... Use as directed

Water Supply Temperature ...... Not to exceed 100°F

Engine Specifications

Bore ......................... 2.688 in. (68.28 mm)

Stroke ........................ 2.040 in. (51.82 mm)

Displacement ..................... 11.58 in. (190 cc)

Spark Plug

Type: .................. Briggs & Stratton 692051

Set Gap To: ................ 0.020 inch (0.051 mm)

Armature Air Gap: ...... 0.010-0.014 in.(0.25-0.36mm)

Valve clearance with valve springs installed and piston

1/4 in. (6 mm) past top dead center (check when engine

is cold).

Intake ................ 0.004-0.008 in.(0.10-0.20 mm)

Exhaust............... 0.004-0.008 in.(0.10-0.20 mm)

Fuel Capacity ........................... 1.6 Quarts

Oil Capacity ................... 20 Ounces (0.6 liter)

NOTICE For practical operation, the engine load

should not exceed 851/oof rated power. Engine power

will decrease 3-1/2% for each 1,000 ft. (300 m) above

sea level and 11/ofor each 10° F (5.6° C) above 77° F

(25 ° C). It should operate satisfactorily at an angle up

to 15°,

* This pressure washer is rated in accordance to

the Pressure Washer Manufacturers Association

(PWMA) standard PW101-2010 (Testing and Rating

Performance of Pressure Washers).

Maintenance Schedule

Follow the hourly or calendar intervals, whichever

occurs first. More frequent service is required when

operating in adverse conditions noted below.

First 5 Hours

, Change engine oil

Every 8 Hours or Daily

= Check/clean water inlet screen 1

• Check high pressure hose

Check detergent siphoning hose

Check spray gun and assembly for leaks

Clean debris

Check engine oil level

Every 50 Hours or Yearly

= Clean engine air cleaner 2

Change engine oil2

Inspect muffler and spark arrester

Every 200 Hours or Yearly

Replace engine air cleaner 2

Yearly

Replace spark plug

Clean cooling system 2

1 Clean if clogged Replace if perforated or torn

2 Service more often under dirty or dusty conditions

General Recommendations

Regular maintenance will improve the performance and

extend the life of the pressure washer. See any Sears

or other qualified service dealer for service.

The pressure washer warranty does not cover items

that have been subjected to operator abuse or

negligence. To receive full value from the warranty, the

operator must maintain pressure washer as instructed

in this manual including proper storage as detailed in

Storage.

Some adjustments will need to be made periodically to

properly maintain your pressure washer.

All service and adjustments should be made at least

once each season. A new spark plug and clean air filter

assure proper fuel-air mixture and help your engine run

better and last longer. Follow the requirements in the

Maintenance Schedule chart above.

Pump Oil

DO NOT attempt any oil maintenance on this pump.

The pump is pre-lubricated and sealed from the factory,

requiring no additional maintenance for the life of the

pump.

Emissions Control

Maintenance, replacement, or repair of the

emissions control devices and systems may

be performed by any non=road engine repair

establishment or individual. However, to obtain

"no charge" emissions control service, the work must

be performed by a factory authorized dealer. See the

Emissions Warranty.

Before Each Use

1. Check engine oil level.

2. Clean debris.

3. Check water inlet screen for damage.

4. Check high pressure hose for leaks.

5. Check gun and nozzle extension assembly for leaks.

6. Purge pump of air and contaminants.

PRESSURE WASHER MAINTENANCE

Clean Debris

Daily or before use, clean accumulated debris from

pressure washer. Keep linkage, spring and controls

clean. Keep area around and behind muffler free from

any combustible debris. Inspect cooling air slots and

openings on the pressure washer. These openings

must be kept clean and unobstructed.

Pressure washer parts should be kept clean to reduce the

risk of overheating and ignition of accumulated debris.

Use a damp cloth to wipe exterior surfaces clean.

NOTICE Improper treatment of pressure washer

could damage it and shorten its life.

• DO NOT insert anyobjectsthrough cooling slots.

Use a soft bristle brush to loosen caked on dirt, oil,

etc.

Use a vacuum cleaner to pick up loose dirt and

debris.

Check and Clean Inlet Screen

Examine garden hose inlet screen. Clean if it is clogged

or replace if it is torn.

Check High Pressure Hose

High pressure hoses can develop leaks from wear,

kinking, or abuse, inspect hose before each use. Check

for cuts, leaks, abrasions, bulging of cover, or damage

or movement of couplings, if any of these conditions

exist, replace hose immediately.

_.' WARNING The high pressure stream of water

that this equipment produces could cut

through skin and its underlying tissues,

resulting in serious injury and possible

amputation.

• NEVER repair high pressure hose.Replace it.

• Replacement hose ratingMUSTequal or exceed

maximum pressure ratingof unit.

Check Detergent Siphoning Tube

Examine the filter on detergent tube (if equipped)

and clean if clogged. The tube should fit tightly on the

barbed fitting. Examine the tube for leaks or tears.

Replace the filter or tube if either is damaged.

Detergent Siphoning Check Ball

Occasionally check ball in detergent siphoning

system may become stuck from storage, dried soap,

or minerals in water. The check ball can be freed by

performing the following:

NOTICE Before performing this procedure, be sure

,ou are wearing safety goggles as described below.

Z_ WARNING Risk of eye injury,

_ pray could splash back or propel objectsresulting in serious injury,

• Always wear indirect vented (chemical splash) safety

goggles marked to comply with ANSI Z87.1 when using

or in vicinity of this equipment.

• NEVER substitute safety glasses or dry-condition

goggles for indirect vented safety goggles.

Shut OFF engine and turn off water supply.

ALWAYS point spray gun in a safe direction,

press red button and squeeze spray gun trigger to

release retained high water pressure.

WARNING The high pressure stream of water

that this equipment produces could cut

through skin and its underlying tissues,

resulting in serious injury and possible

amputation.

Spray gun traps high water pressure, even when

engine is stopped and water is disconnected, which

could result in serious injury.

• Keep high pressure hose connectedto pump and spray

gun while systemis pressurized.

• ALWAYSpoint spraygun in safe direction, press red

button and squeeze spray gun triggerto releasehigh

pressure,every time youstop engine.

Remove detergent siphoning hose from barbed

fitting on pump.

Using a firm, blunt object 7/64" in diameter or

smaller, by at least 1" long, such as an Alien

wrench, slowly insert the object into the barbed

fitting until you meet resistance. This resistance is

the check ball.

5. Slowly push down until you feel the bail move

slightly, push no more than 1/8:'.Slight pressure

may be required to free the bail.

6. Repeat steps 4 and 5 if necessary.

7. Reinstall detergent siphoning hose onto barb

fitting.

8. Treat with PumpSaver as described in Protecting

the Pump during storage to prevent reoccurrence.

Check Spray Gun

Examine hose connection to spray gun and make sure

it is secure. Test trigger by pressing it and making sure

it springs back into place when you release it. Do not

depress red button and test trigger. You should not be

able to press trigger. Replace spray gun immediately if it

fails any of these tests.

Spray Tip Maintenance

A pulsing sensation felt while squeezing the spray gun

trigger may be caused by excessive pump pressure.

The principal cause of excessive pump pressure is a

spray tip clogged or restricted with foreign materials,

such as dirt, etc. To correct the problem, immediately

clean the spray tip following these instructions:

1. Shut off engine and turn off water supply.

2. ALWAYS point spray gun in a safe direction, press

red button and squeeze spray gun trigger to release

retained high water pressure.

.'_ WARNING The high pressure stream of water

that this equipment produces could cutthrough skin and its underlying tissues,

resulting in serious injury and possible

amputation.

Spray gun traps high water pressure, even when

engine is stopped and water is disconnected, which

could result in serious injury.

• Keephigh pressurehose connectedto pumpand spray

gun while system ispressurized.

• ALWAYSpointspray gun in safe direction, press red

button and squeezespray gun trigger to releasehigh

pressure,every time you stop engine.

Remove spray tip from end of nozzle extension.

Use a small paper clip to free any foreign material

clogging or restricting spray tip (A).

Remove nozzle extension from spray gun.

Using a garden hose, remove additional debris by

back flushing water through nozzle extension. Back

flush between 30 to 60 seconds.

7. Reinstall spray tip into nozzle extension.

8. Reconnect nozzle extension to spray gun.

9. Make sure garden hose is connected to water inlet.

Check that high pressure hose is connected to

spray gun and pump. Turn on water.

10. Start engine following instructions How to Start

Your Pressure Washer.

11. Test pressure washer by operating with each quick

connect spray tip.

O-Ring Maintenance

Purchase an O-Ring Repair Kit, Sears item 75116, at

your local Sears or by calling 1-888=331-4569 or online

at www.sears.com. It is not included with the pressure

washer. This kit includes replacement o-rings and a

water inlet filter. Refer to the instruction sheet provided

in the kit to service your unit's o=rings.

WARNING The high pressure stream of water

that this equipment produces could cut

through skin and its underlying tissues,

' ' resulting in serious injury and possible

amputation.

• NEVERrepair leakingconnections with sealant ofany

kind.Replace o-ring or seal.

ENGINE MAINTENANCE

z_ WARNING Unintentional sparking could cause

/_ fire or electric shock resulting in

death or serious injury.

WHEN ADJUSTING OR MAKING REPAIRSTOYOUR

PRESSUREWASHER

• Disconnectthe spark plug wirefrom the spark plug and

placethewire where it cannot contact spark plug.

WHEN TESTING FOR ENGINE SPARK

• Use approvedspark plug tester.

• DONOT check forspark with spark plug removed.

Oil

Oil Recommendations

We recommend the use of Briggs & Stratton Warranty

Certified oils for best performance. Other high-quality

detergent oils are acceptable if classified for service SF,

SG, SH, SJ or higher. DO NOT use special additives.

Outdoor temperatures determine the proper oil

viscosity for the engine. Use the chart to select the best

viscosity for the outdoor temperature range expected.

104

50--

-4

-22

-- Z

-1€

C:3 ¸

CO m

0 m

D 30

_- 20

-10

-20

-30

* Below 40°F (4°C) the use of SAE 30 will result in hard

starting.

** Above 80°F (27°C) the use of 10W30 may cause increased

oil consumption. Check oil level more frequently.

Checking Oil Level

1, Make sure pressure washer is on a level surface,

2, Remove oil dipstick and wipe dipstick with clean

cloth. Replace and tighten dipstick. Remove and

check oil level.

Verify oil is at FULL mark (top hole) on dipstick.

Replace and tighten dipstick.

[/ Full

',,I< J

_., Add

--- ,_

Adding Engine Oil

1. Make sure pressure washer is on a level surface.

2. Check oil level as described in Checking Off Level.

3. If needed, slowly pour oil into oil fill opening to the

FULL mark (top hole) on dipstick. DO NOT overfill.

NOTICE Overfilling with oil could cause the engine to

not start, or hard starting.

• DO NOT overfill.

• If over the FULL mark on dipstick, drain oil to reduce oi!

level to FULL mark on dipstick.

4. Tip your pressure washer to drain oil from oil fill into

a suitable container making sure you tip your unit

away from spark plug. When crankcase is empty,

return pressure washer to upright position.

5. Slowly pour recommended oil (about 20 oz. (0.6 I))

into oil fill opening. Pause to permit oil to settle. Fill

to Full mark (top hole) on dipstick.

6. Wipe dipstick clean each time oil level is checked.

DO NOT overfill.

7. Replace and tighten dipstick.

8. Wipe up any remaining oil.

9. Reconnect spark plug wire to spark plug.

Service Air Cleaner

Your engine will not run properly and may be damaged

if you run it with a dirty air cleaner. Service more

often if operating under dirty or dusty conditions.

Replacements are available at your local Sears service

center.

To service the air cleaner, follow these steps:

1, Slide air cleaner lever (A) to unlock (m") position

and tilt cover (B) down.

4. Replace and tighten dipstick.

Changing Engine Oil

If you are using your pressure washer under extremely

dirty or dusty conditions, or in extremely hot weather,

change oil more often.

_. CAUTION Avoid prolonged or repeated skin

contact with used motor oil.

• Used motor oil has been shown to cause skin cancer in

certain laboratory animals.

• Thoroughly wash exposed areaswith soap and water.

KEEP OUT OF REACH OF CHILDREN.

DON'T POLLUTE. CONSERVE

RESOURCES. RETURN USED OILTO

COLLECTION CENTERS.

Change oil while engine is still warm from running,

as follows:

1. Drain fuel tank by running pressure washer until

fuel tank is empty.

2. Disconnect spark plug wire and keep it away from

spark plug.

3. Clean area around oil fill, remove oil fill cap/

dipstick. Wipe dipstick clean.

2. Carefully remove air cleaner to prevent debris from

falling into carburetor.

3. Wash foam air cleaner (C) in liquid detergent and

water. Squeeze dry in a clean cloth.

4. SATURATE foam air cleaner in engine oil and

squeeze in a clean cloth to remove excess oil.

5. Reinstall clean or new foam air cleaner in base (D).

6. Tilt cover up and slide lever to lock (_,) position.

NOTICE You can purchase new air filter elements by

calling 1=888-331=4569,

Service Spark Plug

Changing the spark plug will help your engine to start

easier and run better.

1. Clean area around spark plug.

2. Remove and inspect spark plug.

3. Replace spark plug if electrodes are pitted, burned

or porcelain is cracked. Use the recommended

replacement plug. See Specifications.

Page is loading ...

Craftsman 020606-00 Owner's manual

Brand: Craftsman

Model: 020606-00

Category: High-pressure cleaners

Type: Owner's manual

This manual is also suitable for

580754890

Download PDF

report

in other languages

español: Craftsman 020606-00 El manual del propietario

Craftsman 020606-00 Owner's manual

This manual is also suitable for

Craftsman 020606-00 Owner's manual

in other languages

Related papers

Other documents