Sanyo VPC-R1E User manual

SERVICE MANUAL

Digital Camera

AC adaptor

VPC-R1

VPC-R1EX

(Product Code : 126 293 00)

(U.S.A., Canada)

(Product Code : 126 293 02)

(Europe, PAL General)

Contents

1. OUTLINE OF CIRCUIT DESCRIPTION .................... 2

2. DISASSEMBLY ........................................................ 11

3. ELECTRICAL ADJUSTMENT .................................. 13

4. USB STORAGE INFORMATION

REGISTRATION ...................................................... 18

5. TROUBLESHOOTING GUIDE................................. 19

6. PARTS LIST............................................................. 20

CABINET AND CHASSIS PARTS 1 ........................ 20

CABINET AND CHASSIS PARTS 2 ........................ 21

ELECTRICAL PARTS .............................................. 22

ACCESSORIES & PACKING MATERIALS ............. 26

AC Adaptor .............................................................. 26

CIRCUIT DIAGRAMS &

PRINTED WIRING BOARDS ...................................... C1

The components designated by a symbol ( ! ) in this schematic diagram designates components whose value are of

special significance to product safety. Should any component designated by a symbol need to be replaced, use only the part

designated in the Parts List. Do not deviate from the resistance, wattage, and voltage ratings shown.

CAUTION : Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type recommended by the manufacturer.

Discard used batteries according to the manufacturer’s instructions.

NOTE : 1. Parts order must contain model number, part number, and description.

2. Substitute parts may be supplied as the service parts.

3. N. S. P. : Not available as service parts.

Design and specification are subject to change without notice.

SB117/U, E, EX, EX2, SVA01/U, EX, E

REFERENCE No. SM5310265

FILE NO.

PRODUCT SAFETY NOTICE

VPC-R1E

(Product Code : 126 293 01)

(U.K.)

VPC-R1G

(Product Code : 126 293 06)

(No Tax)

VAR-G5U

(Product Code : 126 301 01)

(U.S.A., Canada)

VAR-G5EX

(Product Code : 126 301 02)

(Europe, PAL General)

VAR-G5E

(Product Code : 126 301 03)

(U.K.)

– 2 –

Fig. 1-1.Optical Black Location (Top View)

Fig. 1-2. CCD Terminal Name

1. OUTLINE OF CIRCUIT DESCRIPTION

1-1. CA-A CIRCUIT DESCRIPTIONS

Around CCD block

1. IC Configuration

IC903 (RJ24J1AA0PT) CCD imager

IC902 (TC74VHC04FTP) H driver

IC904 (LR366854) V driver

IC905 (AD9806KST) CDS, AGC, A/D converter

2. IC905 (CCD)

[Structure]

Frame transfer type CCD image sensor

Optical size 1/2.8 type

Effective pixels 1300 (H) x 980 (V)

Pixels in total 1353 (H) x 1006 (V)

Optical black

Horizontal (H) direction: left 2 pixels, right 51 pixels

Vertical (V) direction: upper 10 pixels, below 12 pixels

Dummy bit number Horizontal : 20 Vertical : 4

Table 1-1. CCD Pin Description

1, 2, 23, 24

3, 4

5, 6

19, 20

21, 22 PI1, PI2

PI3, PI4

VSUB

PS4, PS3

Image clock

Accumulation clock

Reset gate

N substrate

Image clock

Accumulation clock

P well

0~12 V

PS1, PS2

0~12 V

L=18 V, H=23 V

8 V

CCD output gate

VOG

3.3 V

Frame shift

Line sending

VOUT

CCD output

VDD

Power

VSS GND

VRD

Reset drain

Approx. 13 V

20 V

0 V

20 V

13, 15

PH4, PH2

14, 16

PH1, PH3

L=2.5 V, H=7.5 V

L=0 V, H=5 V

Horizontal register clock

L=26 V, H=29 V

0~12 V

Frame shift

Line sending

Frame shift

Pin No. Symbol

Pin Description

Waveform

Voltage

(LCC24

Top View)

11 12 16

151413

3 2 1 21

2324

VDD

VSS

VRD

PH4

PH1

PH2

PH3

PS1

PS2

VPW

VOUT

PS3

PS4

NSUB

VOG

PI4

PI3

(NC)

PI1

PI2

(NC)

– 3 –

GND

Fig. 1-3. IC903 Block Diagram

Fig. 1-4. IC902 Block Diagram

3. IC903 (H Driver) and IC902 (V Driver)

An H driver (IC903) and V driver (IC902) are necessary in

order to generate the clocks (vertical transfer clock, horizon-

tal transfer clock and electronic shutter clock) which driver

the CCD.

IC902 is an inverter IC which drives the horizontal CCDs (H1

and H2). In addition the VREG 0~7, VXREG2 and VXREG3

signals which are output from IC102 are the vertical transfer

clocks. The clock is drived until peak value which necessary

CCD at IC902.

4. IC901 (CDS, AGC Circuit and A/D Converter)

The video signal which is output from the CCD is input to

Pins (26) and (27) of IC901. There are S/H blocks inside IC905

generated from the XSHP and XSHD pulses, and it is here

that CDS (correlated double sampling) is carried out.

After passing through the CDS circuit, the signal passes

through the AGC amplifier. It is A/C converted internally into

a 10-bit signal, and is then input to IC102.

Fig. 1-5. IC901 Block Diagram

2319

PBLK

A/D

ACVDD

CMLEVEL

VRT

VTB

STBY CLPOB

ADCMODE

TIMING

GENERATOR

CLPDM SHP

SHD ADCCLK

DIN

ADCIN

DOUT

DRVDD

DVDD

ADVDD

37 20

3341

CLAMP

REFERENCE

CLAMP

CDS

PGA

MUX S/H

AD9802

OUT_NSUB

GND

OUT_1

OUT_2

OUT_3

OUT_4

OUT_5

OUT_6

OUT_7

OUT_8

OUT_9

OUT_10

CAP5V

CAPNS

GND

VDD

OCNT

DUTY

IN_1

IN_2

IN_3

IN_4

IN_5

IN_6

IN_7

IN_8

IN_9

IN_10

IN_NSUB

Power circuit

OCNT circuit

DUTY circuit

– 4 –

Fig. 1-6. Horizontal Transfer of CCD Imager and Extraction of Signal Voltage

Fig. 1-7. Theory of Signal Extraction Operation

5. Transfer of Electric Charge by the Horizontal CCD

The transfer system for the horizontal CCD emplays a 4-phase drive method.

The electric charges sent to the final stage of the horizontal CCD are transferred to the floating diffusion (FD), as shown in Fig.

1-6. PR is turned on by the timing in (1), and the floating diffusion is charged to the potential of RD.

The PR is turned off by the timing in (2). In this condition, the floating diffusion is floated at high impedance.

The H2 potential becomes shallow by the timing in (3), and the electric charge now moves to the floating diffusion.

Here, the electric charges are converted into voltages at the rate of V = Q/C by the equivalent capacitance C of the floating

diffusion. PR is then turned on again by the timing in (1) when the H2 potential becomes deep.

Thus, the potential of the floating diffusion changes in proportion to the quantity of transferred electric charge, and becomes

CCD output after being received by the source follower. The equivalent circuit for the output circuit is shown in Fig. 1-7.

6. Lens drive block

6-1. Shutter drive

The regulator (IC952) drives by P ON signal which is output

from the power control IC (IC501) is drived, and then power is

supplied to iris shutter drive IC (IC951). The drive signal

(GPIO4, GPIO5, GPIO6, GPIO7) which is output from the

ASIC (IC102) is drived the iris shutter drive IC (IC951), and

the iris shutter spring is open and closed.

Reset gate pulse

20 V Pre-charge drain bias (PD)

Direction of transfer

Voltage output

Electric

charge

H Register

Floating diffusion gate is

floated at a high impedance.

C is charged

equivalently

H1 H4 H3 H2 H1 H4 H3

(1)

(2)

(3)

CCD OUT

(1)(2)

(3)

FDRD

H1 H4 H3 H2 H1 H4 H3

FDRD

H1 H4 H3 H2 H1 H4 H3

FDRD

– 5 –

2. Outline of Operation

When the shutter opens, detect the 8-bit microprocessor and

transmit to record operation starts.

When the PTG drives the FT-CCD, picture data passes

through the A/D and is then input to the ASIC as 10-bit data.

This data then sends FCP, after which it is carried out various

processing operations on the data (such as gamma correc-

tion and white balance). The data is then sent to the ITP where

processing such as contour emphasis and chroma are car-

ried out, after which it is temporarily stored in the SDRAM.

In case of still picture the data is then compressed by the

JPEG method and in case of picture it is compressed by

MJPEG method and is written to compact flash card.

3. LCD Block

RGB signals corresponding to the LCD driver are output from

the ASIC (video player). The LCD driver converts the RGB

signals that are output from the ASIC to a signal level that is

appropriate for the LCD monitor. These RGB signals and the

control signal which is output by the LCD driver are used to

drive the LCD panel.

The RGB signals are 1H transposed so that no DC compo-

nent is present in the LCD element, and the two horizontal

shift register clocks drive the horizontal shift registers inside

the LCD panel so that the 1H transposed RGB signals are

applied to the LCD panel.

Because the LCD closes more as the difference in potential

between the VCOM (common polar voltage: fixed at DC) and

the R, G and B signals becomes greater, the display becomes

darker; if the difference in potential is smaller, the element

opens and the LCD become brighter. In addition, the bright-

ness and contrast settings for the LCD can be varied by means

of the serial data from the ASIC.

1-2. CA-B CIRCUIT DESCRIPTION

1. Circuit description

1-1. PTG

This is program timing generator. Generates the timing signal

that is needed in order to drive the FT-CCD sensor.

1-2. FCP

The FCP receives the output data from the FT-CCD sensor

via the PTG, and then carries out various processing opera-

tions on the data (such as gamma correction and white

banance).

1-3. ITP

The ITP is a pixel conversion processor. It carries out various

processing operations (such as contour emphasis and chroma)

on the image data that is input from the FCP or from memory,

and then stores the processed data in memory.

1-4. CPU

This is 32 bit RISC CPU.

1-5. Memory controller

This is controlled SDRAM, flash ROM and CF card etc.

1-6. Video player

Outputs the RGB signals that are needed to control the graphic

overlay function and to drive the LCD.

1-7. GPIO

This is a multipurpose I/O. (It can be used as an input/output

port.)

1-8. COM port

This is communication block. Supports USB communication.

1-9. Serial communication

This is the interface for the 8-bit microprocessor.

1-10. LCD driver

The RGB output signals that are output from the ASIC are

converted to a signal level that is appropriate for the LCD moni-

tor.

1-11. LCD monitor

This is the image display device which displays the image

signals supplied from the LCD driver.

– 6 –

1-3. CP1 POWER CIRCUIT DESCRIPTION

1. Outline

This is the main power circuit, and is comprised of the follow-

ing blocks.

Switching controller (IC501)

Digital 5 V and analog system power output (T5001, Q5001)

Digital 2.5 V system power supply (Q5007)

Digital 3.4 V system power supply (Q5018)

LCD system power supply (Q5008, T5002)

Backlight power supply output (Q5013)

Inverter output (T5003, Q5017)

2. Switching Controller (IC501)

This is the basic circuit which is necessary for controlling the

power supply for a PWM-type switching regulator, and is pro-

vided with five built-in channels, only CH2 (digital 5 V, analog

system), CH4 (LCD system), CH3 (digital 2.5 V), CH1 (digital

3.4 V) and CH5 (backlight system) are used. Feedback from

5 V (D) (CH2), 2.5 V (D) (CH3) , 12.4 V (L) (CH4), 3.4 V (D)

(CH1) and 7 V (L) (CH5) power supply outputs are received,

and the PWM duty is varied so that each one is maintained at

the correct voltage setting level.

2-1. Short-circuit protection circuit

If output is short-circuited for the length of time determined

by the condenser which is connected to Pin (29) of IC501, all

output is turned off. The control signal (P ON) are recontrolled

to restore output.

3. Digital 3.4 V Power Output

3.4 V (D) is output. Feedback is sent to pin (41) of the switch-

ing controller (IC501) for PWM control to be carried out.

4. Digital 5 V and Analog System Power Output

5.1 V (D) , 26.4 V (A), 20 V (A), 13 V (A) and 5.1 V (A) are

output. Feedback for the 5.1 V (D) is provided to the switch-

ing controller (Pins (35) of IC501) so that PWM control can

be carried out.

5. Digital 2.5 V System Power Output

2.5 V (D) is output. Feedback is provided to the swiching con-

troller (Pin (23) of IC501) so that PWM control can be carried

out.

6. LCD System Power Output

12.4 V (L) is output. Feedback for the 12.4 V (L) is provided

to the switching controller (Pins (22) of IC501) so that PWM

control can be carried out.

7. Backlight Power Supply output

7.0 V (L) is output. Feedback is sent to pin (17) of the switch-

ing controller (IC501) for PWM control to be carried out.

8. Inverter Output

The backlight uses a flat picture tube. When INV CLK is in-

put, Q5017 carries out switching operations, so that T5003 is

energized and a high-voltage pulse is generated between pins

(3) and (4) of T5003. This high-voltage pulse is applied to the

backlight to make it illuminate.

– 7 –

1-4. CP1 STROBO CIRCUIT DESCRIPTION

1. Charging Circuit

When UNREG power is supplied to the charge circuit and the

CHG signal becomes High (3.3 V), the charging circuit starts

operating and the main electorolytic capacitor is charged with

high-voltage direct current.

However, when the CHG signal is Low (0 V), the charging

circuit does not operate.

1-1. Power switch

When the CHG signal switches to Hi, Q5406 turns ON and

the charging circuit starts operating.

1-2. Power supply filter

L5401 and C5405 constitute the power supply filter. They

smooth out ripples in the current which accompany the switch-

ing of the oscillation transformer.

1-3. Oscillation circuit

This circuit generates an AC voltage (pulse) in order to in-

crease the UNREG power supply voltage when drops in cur-

rent occur. This circuit generates a drive pulse with a frequency

of approximately 50-100 kHz. Because self-excited light omis-

sion is used, the oscillation frequency changes according to

the drive conditions.

1-4. Oscillation transformer

The low-voltage alternating current which is generated by the

oscillation control circuit is converted to a high-voltage alter-

nating current by the oscillation transformer.

1-5. Rectifier circuit

The high-voltage alternating current which is generated at

the secondary side of T5401 is rectified to produce a high-

voltage direct current and is accumulated at electrolytic ca-

pacitor C5412 on the main circuit board.

1-6. Voltage monitoring circuit

This circuit is used to maintain the voltage accumulated at

C5412 at a constance level.

After the charging voltage is divided and converted to a lower

voltage by R5417 and R5419, it is output to the SY-A block as

the monitoring voltage VMONIT. When this VMONIT voltage

reaches a specified level at the SY-A block, the CHG signal is

switched to Low and charging is interrupted.

2. Light Emission Circuit

When RDY and TRIG signals are input from the ASIC, the

stroboscope emits light.

2-1. Emission control circuit

When the RDY signal is input to the emission control circuit,

Q5409 switches on and preparation is made to let current

flow to the light emitting element. Moreover, when a STOP

signal is input, the stroboscope stops emitting light.

2-2. Trigger circuit

When a TRIG signal is input to the trigger circuit, D5405

switches on, a high-voltage pulse of several kilovolts is gen-

erated inside the trigger circuit, and this pulse is then applied

to the light emitting part.

2-3. Light emitting element

When the high-voltage pulse form the trigger circuit is ap-

plied to the light emitting part, currnet flows to the light emit-

ting element and light is emitted.

Beware of electric shocks.

– 8 –

1-5. SY-A CIRCUIT DESCRIPTION

1. Configuration and Functions

For the overall configuration of the SY-A block, refer to the block diagram. The SY-A block centers around a 8-bit microprocessor

(IC301), and controls camera system condition (mode).

The 8-bit microprocessor handles the following functions.

1. Operation key input, 2. Clock control, 3. Power ON/OFF, 4. Strobe charge control.

Signal

1~2

10~12

15~16

17~18

20~23

25~26

35~36

39~40

44~45

48~52

75~78

54~74

79~80

NOT USED

AVSS

AVR

AVCC

VDD3

UNREG (S)

VDD3

STROBO_V

P54~P56

DC_IN

X1, X0

MOD1, 0

P. ST.

S10~S13

P04

P05~P06

PLL_EN

USB_CNT

REQACK

RESET B

NOT USED

VF_LED_G

EXT_IRQ1

SDATA

SCLK

SELF_LED_R

NOT USED

X0A, X1A

BUZZER

CHARGE

NOT USED

VCC

NOT USED

SO0~SO3

NOT USED

I/O

Outline

GND

Analog power

Main (ASIC system) power detection

Battery power input (analog input)

Main (ASIC system) power detection

Connect to GND through register

AC adaptor connection detection (analog input)

Main clock oscillation terminal (4 MHz)

Connect to GND

Reset input

Key matrix input

Connect to GND through register

ASIC PLL permission signal

USB connection detection H : Connection

Reset output to ASIC L : Reset

VF LED (green) ON/OFF signal L : Light

External interruption signal

Serial communication control signal

Self LED (red) ON/OFF signal L : Light

Sub clock oscillation terminal (32.768 kHz)

Buzzer output terminal

Strobo charge ON/OFF signal L : ON

Digital power

Key matrix output

Serial communication control signal

VSS

GND

30 SDIR

Serial communication control signal

31 BAT_OFF

Battery OFF detection H : OFF

32 +3.2_SW

3.2 V power (switch)

Strobo charge voltage input (analog input)

34 P ON

DC/DC converter (analog) ON/OFF signal H : ON

Table 4-1. 8-bit Microprocessor Port Specification

– 9 –

Fig. 4-1 Internal Bus Communication System

Table 4-2. Key Operation

2. Internal Communication Bus

The SY-A block carries out overall control of camera operation by detecting the input from the keyboard and the condition of the

camera circuits. The 8-bit microprocessor reads the signals from each sensor element as input data and outputs this data to the

camera circuits (ASIC) or to the LCD display device as operation mode setting data. Fig. 4-1 shows the internal communication

between the 8-bit microprocessor, ASIC and SPARC lite circuits.

3. Key Operaiton

For details of the key operation, refer to the instruction manual.

8-bit

Microprocessor

ASIC

REQACK

EXT_IRQ1

SDATA

SDIR

SCK

RESET B

SCAN

OUT

SCAN

MAIN SW-PLAY POSITION

MAIN SW-LCD OFF

POSITION

RIGHT

MAIN SW-LCD ON

POSITION

LEFT

COVER SW

DOWN

SET

MODE

FOCUS SW

CF_IN

SHUTTER 1stSHUTTER 2nd

TEST

– 10 –

ASIC,

memory

CCD

8 bit

CPU

LCD

MONITOR

Power voltage

Power OFF

Play back

Shutter switch ON

Resolution, flash, self-timer switch ON

LCD finder

3.3 V

5 V (A)

+12 V etc.

3.2 V

(ALWAYS)

+12 V etc.

OFF

32KHz OFF

OFF

4 MHz OFF

→→

→OFF

4 MHz OFF

OFF

4 MHz OFF

4 MHz ON

OFF

4 MHz ON

Table 4-3. Camera Mode

Note) 4 MHz = Main clock operation, 32 kHz = Sub clock operation

Power switch ON-

Auto power OFF

CAMERA

4. Power Supply Control

The 8-bit microprocessor controls the power supply for the overall system.

The following is a description of how the power supply is turned on and off. When the battery is attached, a regulated 3.2 V

voltage is normally input to the 8-bit microprocessor (IC301) by IC302, so that clock counting and key scanning is carried out

even when the power switch is turned off, so that the camera can start up again. When the battery is removed, the 8-bit micro-

processor operates in sleep mode using the backup capacitor. At this time, the 8-bit microprocessor only carries out clock

counting, and waits in standby for the battery to be attached again. When a switch is operated, the 8-bit microprocessor supplies

power to the system as required.

The 8-bit microprocessor first sets the P ON signal at pin (34) to high, and then turns on the DC/DC converter for the digital

system. After this, it sets RESET B signal at pin (33) to high so that the ASIC is set to the active condition.

After this, in case of driving the CCD, it sets the P (A) ON signal at pin (176) of the ASIC to high, and then turns on the DC/DC

converter for the analog system.

If the LCD monitor is on, the LCD ON signal at pin (175) of the ASIC set to high, and the DC/DC converter for the LCD monitor

is turned on. Once it is completed, the ASIC returns to the reset condition, all DC/DC converters are turned off and the power

supply to the whole system is halted.

– 18 –

4. USB STORAGE INFORMATION

REGISTRATION

USB storage data is important for when the camera is con-

nected to a computer via a USB connection.

If there are any errors in the USB storage data, or if it has not

been saved, the USB specification conditions will not be sat-

isfied, so always check and save the USB storage data.

Preparation:

POWER switch: ON

Adjustment method:

1. Connect the camera to a computer. (Refer to 3-5. Con-

necting the camera to the computer on the page 14.)

2. Double-click on the DscCalDi128a.

3. Click on the Get button in the USB storage window and

check the USB storage data.

VID: SANYO

PID: VPC-R1 or VPC-R1E or VPC-R1EX or VPC-R1G

Serial:

Rev. : 1.00

4. Check the “Serial” in the above USB storage data. If the

displayed value is different from the serial number printed

on the base of the camera, enter the number on the base

of the camera. Then click the Set button.

5. Next, check VID, PID and Rev. entries in the USB storage

data. If any of them are different from the values in 3. above,

make the changes and then click the corresponding Set

button.

Firmware

Image

AWB

Focus

UV Matrix

R Bright

RGB Offset

Tint

B Bright

Gain

Phase

LCD

Calibration

Upload

Initialize

LCD Type

H AFC Test

VCOMDC

VCOMPP

Cal Data

Cal Mode

EVF

USB storage

Get

Set

VID

Set

PID

Set

Serial

Set

Rev.

Set

Setting

Language

Video Mode

VCO

Firmware Version:

– 19 –

5. TROUBLESHOOTING GUIDE

POWER LOSS INOPERTIVE

BARRIER SW

MAIN SW ON

NORMAL

IC301-20 (SCAN IN 0)

PULSE INPUT

CHECK

BARRIER SW,

RB301, D3007

IC302-7 (UNREG)

CHECK

POWER BLOCK

IC301-53

(VDD)

IC301-19

(RESET)

CHECK IC302

CHECK IC302, R3054

IC301-31

(BAT OFF)

CHECK IC302, R3053

IC301-15

OSCILLATION

CHECK X3001

IC301-44

OSCILLATION

CHECK X3002

CHECK IC301

NO PICTURE

MAIN CLOCK FOR SYSTEM OPERATION

NO OPERATION IF ABSENT

CHECK X1102 OSCILLATOR, C1104, C1105

CLK (28.63636MHz)

OSCILLATION

CHECK X1102

SD CLK (57.27 MHz)

OSCILLATION

IC103-38

SD RAM (IC103) MOVEMENT CLOCK

NO READ PROGRAM FROM IC121 IF ABSENT

CHECK IC102, IC103

IC102-237

IC301-39, 40

CHECK SOLDERING OF

MEMORY PIN

INCORRECT HANDSHAKING BETWEEN 8-BIT

CPU AND RS-232C

CHECK EACH INTERFACE

PUSH SHUTTER

BUTTON

IC301-20, 21

(SCAN IN 0, 1)

PULSE INPUT

CHECK RB301,

D3006, D3007

CN301-34

(P ON)

CHECK IC301,

POWER BLOCK

IC102-176

(P(A) ON)

CHECK, IC301, ASIC

(IC102), CA-A BLOCK,

POWER BLOCK

SERIAL

COMMUNICATION

CHECK

IC301, CA-A BLOCK

CHECK CP1

TAKING INOPERATIVE

LOW

OFF

LOW

YES

HIGH

YES

HIGH

LOW

6. PARTS LIST

N.S.P.: Not available as service parts.

LOCATION PARTS NO. DESCRIPTION LOCATION PARTS NO. DESCRIPTION

CABINET & CHASSIS PARTS 1

1 636 064 3505 COVER LENS-SB117/EX2,VPC-R1G ONLY

1 636 062 7628 COVER LENS-SB117/U,EXCEPT VPC-R1G

2 636 064 3581 DEC FRONT-SB117/EX2,VPC-R1G ONLY

2 636 063 1595 DEC FRONT-SB117/U,EXCEPT VPC-R1G

3 636 065 3832 ASSY,CABI FRONT SV-117/U ,EXCEPT VPC-R1G

3 636 065 3863 ASSY,CABI FRONT SV-117/EX2 ,VPC-R1G ONLY

4 636 064 3567 COVER BATTERY-SB117/EX2,VPC-R1G ONLY

4 636 062 7642 COVER BATTERY-SB117/U,EXCEPT VPC-R1G

5 636 063 0925 TERMINAL BATT D-SB117/U

6 636 062 8090 STAND-SB117/U, STAND

7 636 063 1663 SPRING COVER LENS-SB117/U

8 636 062 7697 HOLDER COVER LENS-SB117/U

9 636 065 1333 SPACER CABI FRONT-SB117/U

10 636 064 3475 CABINET TOP B-SB117/EX2,VPC-R1G ONLY

10 636 062 7611 CABINET TOP B-SB117/U,EXCEPT VPC-R1G

11 636 063 2189 SPRING SHUTTER-SB117/U

12 636 064 2997 ASSY,BUT SHUTTER-SB117/U,

EXCEPT VPC-R1G

12 636 064 3147 ASSY,BUT SHUTTER-SB117EX2,

VPC-R1G ONLY

13 636 064 3444 CABINET TOP A-SB117/EX2,VPC-R1G ONLY

13 636 062 7604 CABINET TOP A-SB117/U,EXCEPT VPC-R1G

14 636 063 1625 SPACER MONITOR-SB117/U

15 636 062 8335 SLIDE FUNCTION-SB117/U

16 636 063 1632 SHAFT CARD-SB117/U

17 636 064 3536 COVER CARD-SB117/EX2,VPC-R1G ONLY

17 636 062 7635 COVER CARD-SB117/U,EXCEPT VPC-R1G

18 636 065 3870 ASSY,CABI BACK SV-117/U ,EXCEPT VPC-R1G

18 636 065 3917 ASSY,CABI BACK SV-117/EX2 ,VPC-R1G ONLY

19 636 062 8304 KNOB FUNCTION-SB117/U

20 636 062 8076 DEC MONITOR-SB117/U

101 411 177 6502 SCR S-TPG PAN PCS 1.7X4

102 411 177 8100 SCR S-TPG PAN PCS 1.7X2.5

103 411 177 8407 SCR S-TPG PAN PCS 1.7X3

104 411 177 9503 SCR S-TPG PAN PCS 1.7X3

105 411 181 7007 SCR S-TPG PAN PCS 1.7X6.0

[VPC-R1/R1E/R1EX/R1G]

SB117/U Parts Lisut-1

101

102

103

104

105

102

N.S.P.: Not available as service parts.

LOCATION PARTS NO. DESCRIPTION LOCATION PARTS NO. DESCRIPTION

CABINET & CHASSIS PARTS 2

1 645 049 8633 LENS(ASSY)

2 636 064 7015 SPACER,L04

3 645 049 7384 OPTICAL FILTER

4 636 063 2653 SPACER

5 636 062 8137 COMPL PWB,CP-1

6 636 062 7666 HOLDER MONITOR-SB117/U

7 636 063 2110 COMPL,LCD-SB117

8 636 065 0909 SPACER CV MONITOR 2-117J2

9 636 064 2935 SPACER CV MONITOR-SB117/U

10 636 063 1656 SPRING MACRO-SB117/U

11 636 062 8083 KNOB MACRO-SB117/U

12 645 025 1252 SWITCH,LEAF 1P-1T

13 636 062 7680 HOLDER CHASSIS B-SB117/U

14 403 324 3502 DL-ELECT 0.1F Z 5.5V

15 645 025 1252 SWITCH,LEAF 1P-1T

16 645 048 9969 ASSY,LAMP,SB117

17 636 063 0918 TERMINAL BATT C-SB117/U

18 636 062 7765 TERMINAL BATT B-SB117/U

19 636 062 7758 TERMINAL BATT A-SB117/U

20 636 065 1838 ASSY,HLD CHASSIS A-SV 117

21 636 062 8144 COMPL PWB,TB-1

22 419 002 6604 PIEZO BUZZER PS1550L40N

23 645 049 8664 LENS,VF(ASSY)

24 636 062 8069 DEC SELF-SB117/U

101 411 177 6502 SCR S-TPG PAN PCS 1.7X4

103 411 177 8407 SCR S-TPG PAN PCS 1.7X3

106 411 182 3701 SCRS-TPG PAN PCS 1.7X5

107 411 175 3701 SCR S-TPG PAN PCS 1.7X3.5

SB117/J Parts Lisut-2

101

103

107

N.S.P.

106

Note:

1. Materials of Capacitors and Resistors are abbreviated as follows ;

Resistors Capacitors

MT-FILM Metallized Film Resistor MT-POLYEST Metallized Polyester Capacitor

MT-GLAZE Metallized Glaze Resistor MT-COMPO Metallized Composite Capacitor

OXIDE-MT Oxide Metallized Film Resistor TA-SOLD Tantalum Solid Capacitor

AL-SOLID Aluminum Solid Capacitor

NP-ELECT Non-Polarized Electrolytic Capacitor

OS-SOLID Aluminum Solid Capacitors with Organic

Semiconductive Electrolytic Capacitor

DL-ELECT Double Layered Electrolytic Capacitor

2. Tolerance of Capacitor (10pF over) and Resistor are noted with follow symboles.

F ............1% G ............2% J ............5% K ............10%

M ..........20% N ..........30% Z ..........+80% ~ -20%

3. Capacitors

U :

F P : pF

4. Inductors

UH :

H MH : mH

5. N.S.P. : Not available as service parts.

ELECTRICAL PARTS

LOCATION PARTS NO. DESCRIPTION LOCATION PARTS NO. DESCRIPTION

COMPL PWB,CP-1

636 062 8137

(SEMICONDUCTORS)

Q1302 405 102 5609 TR 2SD1819A-R

OR 405 092 4101 TR 2SC4081-R

Q1601 405 133 8907 TR DTC114EUA

OR 405 119 0802 TR UN5211

OR 405 078 7300 TR 2SC4398

Q1602 405 102 6705 TR 2SA1745-7

OR 405 102 8303 TR 2SA1745-6

Q1706 405 115 7201 TR DTC144EE

OR 405 102 5500 TR 2SB1218A-R

OR 405 137 2000 TR 2SA1576A-R

Q3001 405 102 5609 TR 2SD1819A-R

OR 405 092 4101 TR 2SC4081-R

OR 405 078 7300 TR 2SC4398

Q3002 405 102 5609 TR 2SD1819A-R

OR 405 092 4101 TR 2SC4081-R

OR 405 078 7300 TR 2SC4398

Q3004 405 115 5504 TR DTA114EE

Q5001 405 150 5002 TR CPH3109

Q5002 405 115 5108 TR 2SA1774 R

Q5003 405 115 5108 TR 2SA1774 R

Q5005 405 157 1403 TR 2SA2018

Q5006 405 129 2902 TR UMH11N

Q5007 405 153 7508 TR CPH5701

Q5008 405 150 5002 TR CPH3109

Q5009 405 129 2902 TR UMH11N

Q5010 405 157 1403 TR 2SA2018

Q5013 405 150 5200 TR CPH5703

Q5014 405 157 1403 TR 2SA2018

Q5015 405 115 6907 TR DTC114EE

Q5016 405 130 1109 TR UMY1N

Q5017 405 153 8406 TR FTS2005

Q5018 405 153 7508 TR CPH5701

Q5401 405 115 7508 TR DTC123JE

Q5402 405 115 6907 TR DTC114EE

Q5405 405 147 9709 TR CPH3205

Q5406 405 150 5002 TR CPH3109

Q5407 405 115 5207 TR 2SC4617 R

Q5409 405 158 0306 TR CY25AAJ-8

Q9001 405 133 8907 TR DTC114EUA

OR 405 119 0802 TR UN5211

OR 405 078 7300 TR 2SC4398

Q9002 405 165 7305 TR BFR92AW

Q9003 405 102 5500 TR 2SB1218A-R

OR 405 137 2000 TR 2SA1576A-R

(INTEGRATED CIRCUITS)

IC102 409 509 6504 IC CX11637-21 (BGA) (N.S.P.)

IC103 409 482 0506 IC HY57V651620BTC-10S

OR 409 502 3807 IC HY57V641620HGT-H

IC106 409 484 7602 IC NC7SZ08P5

IC121 4095 220 0305 IC 29300117F

IC141 409 471 4102 IC SN74LV244ADB

IC142 409 471 4201 IC SN74LV245ADB

IC143 409 471 4201 IC SN74LV245ADB

IC145 409 368 5809 IC TC7SH08FU

IC171 409 462 2902 IC LV4135W

IC173 409 453 0702 IC TK11330BM

IC175 409 400 9109 IC TC7SET08FU

IC301 410 426 0209 IC MB89165LPFV-G-360-BND

IC302 409 383 1008 S-8423NFS

IC501 409 496 5009 IC BD9731KV

IC502 409 301 5507 IC TC7S08FU

IC901 409 498 6806 IC AD9806KST

IC902 409 507 4403 IC LC89906V(TE-L)

IC903 409 514 2102 IC 74ACTQ04MTC

IC904 409 407 0505 IC TK11331BM

IC905 409 503 0508 IC LC99351(CCD)

IC951 409 247 1205 IC LB1837M

IC952 409 513 0505 IC TK71735S

(DIODES)

D1001 407 149 0807 DIODE 1SS355

D1701 407 166 0606 DIODE MA365

D3002 407 205 2707 LED SML-310LT

D3003 407 201 7607 LED SML-310MT

D3004 407 220 5905 DIODE HN1D01FU

OR 407 175 2202 DIODE UMP11N

D3005 407 220 5905 DIODE HN1D01FU

OR 407 175 2202 DIODE UMP11N

D3006 407 220 5905 DIODE HN1D01FU

OR 407 175 2202 DIODE UMP11N

D3007 407 220 5905 DIODE HN1D01FU

OR 407 175 2202 DIODE UMP11N

D3051 407 149 0807 DIODE 1SS355

D5001 407 199 4909 DIODE 1SS376

D5002 407 149 0807 DIODE 1SS355

D5003 407 210 5403 DIODE RB551V-30

D5004 407 162 8507 DIODE DAN222

D5005 407 190 3703 DIODE RB050L-40-TE25

D5006 407 149 0807 DIODE 1SS355

D5007 407 190 3703 DIODE RB050L-40-TE25

D5008 407 149 0807 DIODE 1SS355

D5013 407 210 5403 DIODE RB551V-30

D5402 407 202 0300 DIODE F1F16

D5404 407 202 0102 DIODE F1SN4

D5405 407 199 4503 DIODE CR08AS-8-T1

D5407 407 162 8507 DIODE DAN222

D9001 407 105 6102 DIODE SB007-03Q

D9002 407 105 6102 DIODE SB007-03Q

D9003 407 113 5609 DIODE DSH015

OR 407 134 7200 DIODE MA141K

OR 407 220 7305 DIODE MA142K-G

OR 407 153 7205 DIODE MA142K

D9004 407 113 5609 DIODE DSH015

LOCATION PARTS NO. DESCRIPTION LOCATION PARTS NO. DESCRIPTION

D9004 407 134 7200 DIODE MA141K

OR 407 220 7305 DIODE MA142K-G

OR 407 153 7205 DIODE MA142K

D9005 407 113 5609 DIODE DSH015

OR 407 134 7200 DIODE MA141K

OR 407 220 7305 DIODE MA142K-G

OR 407 153 7205 DIODE MA142K

D9006 407 113 5609 DIODE DSH015

OR 407 134 7200 DIODE MA141K

OR 407 220 7305 DIODE MA142K-G

OR 407 153 7205 DIODE MA142K

(OSC)

X1101 645 049 1085 OSC,CRYSTAL 48.000MHZ

X1102 645 049 1078 OSC,CRYSTAL 28.63636MHZ

X3001 645 046 1415 OSC,CERAMIC 4.00MHZ

X3002 636 040 1129 OSC CRYSTAL 32.768KHZ

(FILTER)

XF131 645 049 3430 FILTER,220-100M

(VARIABLE RESISTORS)

VR502 645 046 7844 VR,SEMI,2.2K S

(INDUCTORS)

L1001 645 041 1977 INDUCTOR,330 OHM

L1002 645 041 1977 INDUCTOR,330 OHM

L1071 645 020 1899 INDUCTOR,68 OHM

L1101 645 021 1645 INDUCTOR,2.2U J

L1502 645 041 1977 INDUCTOR,330 OHM

L1701 645 035 7183 INDUCTOR,10U J

L1702 645 004 2478 INDUCTOR,10U J

L1703 645 041 1977 INDUCTOR,330 OHM

L3001 645 049 1504 IMPEDANCE,120 OHM P

L5001 645 033 8762 INDUCTOR,47U K

L5002 645 033 8762 INDUCTOR,47U K

L5003 645 033 8762 INDUCTOR,47U K

L5004 645 033 8663 INDUCTOR,10U K

L5006 645 037 0632 INDUCTOR,47U M

L5007 645 033 8762 INDUCTOR,47U K

L5009 645 049 1825 IMPEDANCE,180 OHM P

L5010 645 049 1825 IMPEDANCE,180 OHM P

L5011 645 040 3286 INDUCTOR,22U M

L5012 645 033 8663 INDUCTOR,10U K

L5013 645 033 8663 INDUCTOR,10U K

L5014 645 021 5315 INDUCTOR,110 OHM

L5016 645 037 0632 INDUCTOR,47U M

L5401 645 037 0618 INDUCTOR,15U M

L9001 645 020 1912 INDUCTOR,240 OHM

(TRANSFORMERS)

T5001 645 048 5831 TRANS,POWER,PULSE

T5002 645 047 2336 TRANS,POWER,PULSE

T5003 645 027 5425 TRANS,POWER,PULSE

T5401 645 044 6641 TRANS,STEP UP

T5402 645 031 6951 TRANS,STEP UP

(CAPACITORS)

C1001 403 312 6805 CERAMIC 0.1U Z 16V

C1002 403 312 6805 CERAMIC 0.1U Z 16V

C1003 403 312 6805 CERAMIC 0.1U Z 16V

C1004 403 312 6805 CERAMIC 0.1U Z 16V

C1005 403 312 6805 CERAMIC 0.1U Z 16V

C1006 403 312 6805 CERAMIC 0.1U Z 16V

C1007 403 312 6805 CERAMIC 0.1U Z 16V

C1008 403 312 6805 CERAMIC 0.1U Z 16V

C1009 403 311 4505 CERAMIC 1000P K 50V

C1010 403 312 6805 CERAMIC 0.1U Z 16V

C1011 403 312 6805 CERAMIC 0.1U Z 16V

C1012 403 312 6805 CERAMIC 0.1U Z 16V

C1013 403 312 6805 CERAMIC 0.1U Z 16V

C1014 403 312 6805 CERAMIC 0.1U Z 16V

C1015 403 312 6805 CERAMIC 0.1U Z 16V

C1016 403 312 6805 CERAMIC 0.1U Z 16V

C1017 403 312 6805 CERAMIC 0.1U Z 16V

C1061 403 312 6805 CERAMIC 0.1U Z 16V

C1062 403 312 6805 CERAMIC 0.1U Z 16V

C1063 403 324 0501 CERAMIC 10U Z 10V

C1064 403 312 6805 CERAMIC 0.1U Z 16V

C1071 403 312 6805 CERAMIC 0.1U Z 16V

C1072 403 312 6805 CERAMIC 0.1U Z 16V

C1073 403 312 6805 CERAMIC 0.1U Z 16V

C1074 403 312 6805 CERAMIC 0.1U Z 16V

C1101 403 311 5809 CERAMIC 47P J 50V

C1102 403 309 8102 CERAMIC 5P C 50V

C1103 403 309 8102 CERAMIC 5P C 50V

C1104 403 311 7803 CERAMIC 8P D 50V

C1105 403 311 7803 CERAMIC 8P D 50V

C1201 403 332 9503 CERAMIC 1U M 6.3V

C1301 403 311 5809 CERAMIC 47P J 50V

C1302 403 311 5809 CERAMIC 47P J 50V

C1401 403 312 6805 CERAMIC 0.1U Z 16V

C1402 403 312 6805 CERAMIC 0.1U Z 16V

C1403 403 312 6805 CERAMIC 0.1U Z 16V

C1412 403 312 6805 CERAMIC 0.1U Z 16V

C1502 403 324 0501 CERAMIC 10U Z 10V

C1503 403 311 3409 CERAMIC 0.01U K 16V

C1504 403 311 3409 CERAMIC 0.01U K 16V

C1704 403 311 3409 CERAMIC 0.01U K 16V

C1705 403 312 6003 CERAMIC 39P J 50V

C1706 403 319 3005 CERAMIC 220P J 25V

C1707 403 155 1807 CERAMIC 0.01U K 25V

C1709 403 317 1904 CERAMIC 6800P K 25V

C1711 403 283 6309 CERAMIC 1U Z 10V

C1712 403 346 2309 CERAMIC 0.1U K 10V

C1713 403 311 3409 CERAMIC 0.01U K 16V

C1714 403 346 2309 CERAMIC 0.1U K 10V

C1715 403 323 6009 CERAMIC 10U M 16V

C1721 403 338 0405 CERAMIC 0.47U K 25V

C1722 403 338 0405 CERAMIC 0.47U K 25V

C1723 403 338 0405 CERAMIC 0.47U K 25V

C1726 403 155 1807 CERAMIC 0.01U K 25V

C1727 403 338 0405 CERAMIC 0.47U K 25V

C1731 403 332 9503 CERAMIC 1U M 6.3V

C1732 403 332 9503 CERAMIC 1U M 6.3V

C1733 403 332 9503 CERAMIC 1U M 6.3V

C1734 403 332 9503 CERAMIC 1U M 6.3V

C1735 403 335 4802 CERAMIC 0.33U K 6.3V

C1736 403 346 2309 CERAMIC 0.1U K 10V

C1737 403 346 2309 CERAMIC 0.1U K 10V

C1738 403 311 5809 CERAMIC 47P J 50V

C1739 403 311 5809 CERAMIC 47P J 50V

C1740 403 311 5809 CERAMIC 47P J 50V

C1741 403 358 3202 CERAMIC 10U K 6.3V

C1746 403 332 9503 CERAMIC 1U M 6.3V

C1748 403 358 3202 CERAMIC 10U K 6.3V

C1754 403 332 9503 CERAMIC 1U M 6.3V

C1775 403 207 0307 CERAMIC 1U Z 16V

C3001 403 345 4304 TA-SOLID 22U M 10V

C3002 403 312 6805 CERAMIC 0.1U Z 16V

C3003 403 312 6805 CERAMIC 0.1U Z 16V

C3005 403 312 6805 CERAMIC 0.1U Z 16V

C3007 403 312 6805 CERAMIC 0.1U Z 16V

C3008 403 323 9406 TA-SOLID 10U M 10V

C3009 403 312 6805 CERAMIC 0.1U Z 16V

C3010 403 311 4505 CERAMIC 1000P K 50V

C3011 403 311 7506 CERAMIC 22P J 50V

C3012 403 309 8607 CERAMIC 18P J 50V

C3051 403 207 0307 CERAMIC 1U Z 16V

C3052 403 312 6805 CERAMIC 0.1U Z 16V

C3053 403 312 6805 CERAMIC 0.1U Z 16V

C3054 403 312 6805 CERAMIC 0.1U Z 16V

C3056 403 311 3409 CERAMIC 0.01U K 16V

C3057 403 312 6805 CERAMIC 0.1U Z 16V

C5001 403 311 4505 CERAMIC 1000P K 50V

C5002 403 311 4505 CERAMIC 1000P K 50V

C5003 403 311 4505 CERAMIC 1000P K 50V

C5004 403 311 4505 CERAMIC 1000P K 50V

C5005 403 311 4505 CERAMIC 1000P K 50V

C5006 403 311 4505 CERAMIC 1000P K 50V

C5007 403 311 3409 CERAMIC 0.01U K 16V

C5008 403 311 3409 CERAMIC 0.01U K 16V

C5009 403 338 4403 CERAMIC 0.1U K 16V

C5010 403 338 4403 CERAMIC 0.1U K 16V

C5011 403 311 3409 CERAMIC 0.01U K 16V

C5012 403 343 8700 CERAMIC 1U M 12V

C5013 403 352 7305 CERAMIC 4.7U K 6.3V

C5014 403 343 8700 CERAMIC 1U M 12V

C5015 403 352 7305 CERAMIC 4.7U K 6.3V

C5016 403 348 9108 CERAMIC 0.47U K 6.3V

C5017 403 319 3005 CERAMIC 220P J 25V

C5018 403 338 4403 CERAMIC 0.1U K 16V

C5019 403 311 7605 CERAMIC 2200P K 50V

C5020 403 338 4403 CERAMIC 0.1U K 16V

C5021 403 338 4403 CERAMIC 0.1U K 16V

C5022 403 317 1201 CERAMIC 0.22U K 50V

C5026 403 317 1201 CERAMIC 0.22U K 50V

C5027 403 311 1801 CERAMIC 1U K 10V

C5029 403 340 1803 CERAMIC 1U M 25V

C5030 403 340 1803 CERAMIC 1U M 25V

C5031 403 343 3101 CERAMIC 1U K 6.3V

C5033 403 334 3806 CERAMIC 10U K 6.3V

C5034 403 334 3806 CERAMIC 10U K 6.3V

C5035 403 311 7605 CERAMIC 2200P K 50V

C5036 403 340 6907 CERAMIC 1U K 16V

C5037 403 340 6907 CERAMIC 1U K 16V

C5038 403 340 6907 CERAMIC 1U K 16V

C5039 403 334 3806 CERAMIC 10U K 6.3V

C5040 403 311 1801 CERAMIC 1U K 10V

C5041 403 367 6607 POS-SOLID 47U M 6.3V

C5042 403 311 7704 CERAMIC 4700P K 25V

C5043 403 311 1801 CERAMIC 1U K 10V

C5044 403 367 6607 POS-SOLID 47U M 6.3V

C5045 403 311 7704 CERAMIC 4700P K 25V

C5047 403 325 0500 CERAMIC 2.2U K 16V

C5048 403 340 6907 CERAMIC 1U K 16V

C5049 403 311 7605 CERAMIC 2200P K 50V

C5050 403 348 9108 CERAMIC 0.47U K 6.3V

C5052 403 113 4109 CERAMIC 2200P K 50V

C5054 403 309 8706 CERAMIC 100P J 50V

C5055 403 340 6907 CERAMIC 1U K 16V

C5057 403 333 3609 POS-SOLID 33U M 10V

C5058 403 311 4505 CERAMIC 1000P K 50V

C5059 403 333 3609 POS-SOLID 33U M 10V

C5401 403 341 4407 CERAMIC 0.047U K 350V

C5402 403 330 5903 CERAMIC 0.01U K 500V

C5403 403 163 9604 CERAMIC 0.033U Z 25V

C5404 403 311 4505 CERAMIC 1000P K 50V

C5405 403 341 4803 CERAMIC 10U K 10V

C5406 403 307 7008 CERAMIC 0.068U K 16V

C5407 403 113 4109 CERAMIC 2200P K 50V

C5412 404 087 6601 ELECT 120U A 330V

C9001 403 312 6805 CERAMIC 0.1U Z 16V

C9002 403 312 6805 CERAMIC 0.1U Z 16V

C9003 403 312 6805 CERAMIC 0.1U Z 16V

C9004 403 312 6805 CERAMIC 0.1U Z 16V

C9005 403 311 7605 CERAMIC 2200P K 50V

C9006 403 312 6805 CERAMIC 0.1U Z 16V

C9008 403 312 6805 CERAMIC 0.1U Z 16V

C9009 403 312 6805 CERAMIC 0.1U Z 16V

C9010 403 312 6805 CERAMIC 0.1U Z 16V

C9011 403 312 6805 CERAMIC 0.1U Z 16V

C9012 403 320 5302 CERAMIC 0.15U K 25V

C9013 403 345 4304 TA-SOLID 22U M 10V

C9014 403 311 3409 CERAMIC 0.01U K 16V

C9015 403 311 3409 CERAMIC 0.01U K 16V

C9016 403 343 8700 CERAMIC 1U M 12V

C9017 403 311 3409 CERAMIC 0.01U K 16V

C9018 403 343 8700 CERAMIC 1U M 12V

C9019 403 312 6805 CERAMIC 0.1U Z 16V

C9022 403 312 6805 CERAMIC 0.1U Z 16V

C9023 403 312 6805 CERAMIC 0.1U Z 16V

C9024 403 312 6805 CERAMIC 0.1U Z 16V

C9025 403 312 6805 CERAMIC 0.1U Z 16V

C9026 403 367 6102 CERAMIC 4.7U K 16V

C9027 403 217 9604 ELECT 100U M 16V

C9028 403 312 6805 CERAMIC 0.1U Z 16V

C9029 403 312 6805 CERAMIC 0.1U Z 16V

C9030 403 338 4403 CERAMIC 0.1U K 16V

C9031 403 343 8700 CERAMIC 1U M 12V

C9040 403 343 8700 CERAMIC 1U M 12V

C9042 403 343 8700 CERAMIC 1U M 12V

C9043 403 164 0204 CERAMIC 0.1U Z 25V

C9044 403 311 3409 CERAMIC 0.01U K 16V

C9045 403 312 6805 CERAMIC 0.1U Z 16V

C9046 403 164 0204 CERAMIC 0.1U Z 25V

C9047 403 164 0204 CERAMIC 0.1U Z 25V

C9048 403 312 6805 CERAMIC 0.1U Z 16V

C9049 403 312 6805 CERAMIC 0.1U Z 16V

C9050 403 338 4403 CERAMIC 0.1U K 16V

C9051 403 213 5501 ELECT 10U M 25V

C9052 403 312 6805 CERAMIC 0.1U Z 16V

C9053 403 164 0204 CERAMIC 0.1U Z 25V

C9054 403 164 0204 CERAMIC 0.1U Z 25V

C9056 403 218 4905 ELECT 4.7U M 35V

C9057 403 312 6805 CERAMIC 0.1U Z 16V

C9058 403 164 0204 CERAMIC 0.1U Z 25V

C9059 403 280 3400 ELECT 47U M 35V

C9501 403 338 4403 CERAMIC 0.1U K 16V

C9502 403 332 9503 CERAMIC 1U M 6.3V

C9503 403 155 1807 CERAMIC 0.01U K 25V

(RESISTOR PACKS)

RB101 645 037 0816 R-NETWORK 0X4 1/32W