Miele KM3010G Installation guide

Category
Hobs
Type
Installation guide

Miele KM3010G: The Miele KM3010G gas cooktop offers a variety of features to make cooking easier and more enjoyable. With its four burners, you can cook multiple dishes at once, and the cast-iron grates provide a stable surface for your pots and pans. The cooktop also features electronic ignition, so you don't have to worry about fumbling with matches or lighters. And the sleek design of the cooktop will complement any kitchen décor.

Here are some of the benefits of the Miele KM3010G gas cooktop:

  • Four burners for cooking multiple dishes at once
  • Cast-iron grates for a stable surface for your pots and pans

Miele KM3010G: The Miele KM3010G gas cooktop offers a variety of features to make cooking easier and more enjoyable. With its four burners, you can cook multiple dishes at once, and the cast-iron grates provide a stable surface for your pots and pans. The cooktop also features electronic ignition, so you don't have to worry about fumbling with matches or lighters. And the sleek design of the cooktop will complement any kitchen décor.

Here are some of the benefits of the Miele KM3010G gas cooktop:

  • Four burners for cooking multiple dishes at once
  • Cast-iron grates for a stable surface for your pots and pans
Operating and Installation Instructions
Gas Cooktop
To prevent accidents and machine damage, read the Operating Manual
before installation or use.
M.-Nr. 09 317 500en - US, CA
2
WARNING:
If the information in this manual is not followed
exactly, a fire or explosion may result causing
property damage, personal injury or death.
Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any
other appliance.
WHAT TO DO IF YOU SMELL GAS
ß Do not try to light any appliance.
ß Do not touch any electrical switch.
ß Do not use any phone in your building.
ß Immediately call your gas supplier from a
neighbor’s phone. Follow the gas supplier’s
instructions.
ß If you cannot reach your gas supplier, call the
fire department.
Installation and service must be performed by a
qualified installer, service agency or the gas
supplier.
(In Massachusetts installation must be performed
by a licensed plumber / gas fitter.)
Note to the installer:
Please leave this instruction book with the
consumer for the local electrical / gas inspector’s
use.
®
®
IMPORTANT SAFETY INSTRUCTIONS.................................4
Guide to the appliance .............................................9
Before the first use ...............................................11
Operation .......................................................12
Control knobs.....................................................12
Turning on .......................................................12
Turning on in the event of a power failure ............................13
Regulating .......................................................13
Turning off .......................................................13
Cookware .......................................................14
Energy saving tips ................................................15
Safety feature ....................................................16
Cleaning and care ................................................17
Frequently asked questions ........................................20
Technical Service.................................................21
IMPORTANT INSTALLATION SAFETY INSTRUCTIONS ..................24
Installation dimensions ............................................27
Installation ......................................................28
Electrical connection..............................................30
Wiring diagram ...................................................31
Gas connection ..................................................32
Gas pressure regulator .............................................33
Conversion to another type of gas...................................34
Burner capacity ..................................................35
Nominal ratings ...................................................35
Help protect our environment.......................................36
Contents
3
WARNING - When using your gas
appliance follow basic
precautions, including the
following:
This gas cooktop conforms to all
uniform safety codes and
regulations.
Read all instructions before
installation or use to prevent
injury and appliance damage.
These instructions contain
important information on
installation, safety, use and
maintenance of this appliance.
They will help you avoid injury
and damage to the appliance.
Keep these operating instructions
in a safe place and pass them on
to any future user.
SAVE THESE INSTRUCTIONS
Correct usage
~
This appliance is intended for use in
domestic households and in similar
working and residential environments.
~
Only use this gas cooktop for
residential purposes such as cooking
and keeping food warm.
Other uses are not permitted and can
be dangerous.
~
This appliance is not intended for
outdoor use.
~
This equipment has not been
designed for maritime use or for use in
mobile installations such as aircraft or
recreational vehicles.
~
Persons who lack physical, sensory
or mental abilities, or experience with
the appliance should not use it without
supervision or instruction by a
responsible person.
IMPORTANT SAFETY INSTRUCTIONS
4
Children
~
Children should not be left
unattended in an area where the
appliance is in use. Never allow
children to sit or stand on any part of
the appliance.
Caution: Do not store items of interest
to children in cabinets above the
appliance. Children climbing on the
appliance to reach these items could
be injured.
~
The appliance is hot during use and
remains so for some time after being
switched off. Keep children away from
the appliance.
~
Keep all pots and pans out of the
reach of children. Danger of burning or
scalding.
~
Ensure that any packing material, is
disposed of safely and kept out of the
reach of children. Danger of
suffocation!
Technical safety
~
Installation, repair and maintenance
work should be performed by a Miele
authorized service technician in
accordance with local building and
safety codes. Work by unqualified
persons could be dangerous and may
void the warranty.
~
Before installing the cooktop, check
for externally visible damage. Do not
operate a damaged appliance. A
damaged gas cooktop is a hazard.
~
Be certain your appliance is
properly installed and grounded by a
qualified technician.
~
To guarantee the electrical safety of
this appliance, continuity must exist
between the appliance and an effective
grounding system. It is imperative that
this basic safety requirement be met. If
there is any doubt, have the electrical
system of the house checked by a
qualified electrician.
~
Before installation, make sure that
the voltage and frequency listed on the
rating label correspond with the
household electrical supply. This data
must correspond to prevent injury and
appliance damage. Consult a qualified
electrician if in doubt.
~
Do not operate the appliance until it
has been properly installed in the
countertop.
~
Under no circumstance open the
outer casing of the appliance. This is a
safety hazard and may damage the
appliance.
IMPORTANT SAFETY INSTRUCTIONS
5
~
Before servicing, turn off the gas
valve and disconnect the power supply
by either removing the fuse, unplugging
the unit or manually "tripping" the circuit
breaker.
~
While the appliance is under
warranty repairs should only be
performed by a Miele authorized ser
-
vice technician. Otherwise the warranty
is void.
~
Defective components should be
replaced by Miele original spare parts
only. Only with these parts can the
manufacturer guarantee the safety of
the appliance.
~
The appliance is not designed for
use with an external timer or a remote
control system.
~
Do not operate any appliance with a
damaged cord or plug, or if the
appliance has been damaged in any
manner. Contact Miele’s Technical Ser-
vice Department.
~
Do not use an extension cord to
connect this appliance to electricity.
Extension cords do not guarantee the
required safety of the appliance.
~
In the event of damage or defect,
turn off the appliance immediately. Turn
off the gas shut off valve and
disconnect completely from the
electrical supply. Contact the Miele
Technical Service Department.
Do not use the appliance until it has
been repaired.
Ensure power is not supplied to the
appliance while repair work is carried
out.
~
Any breakages or cracks in the
ceramic surface of the appliance are
defects and must be treated as such.
Turn it off immediately. Disconnect the
gas cooktop from the electrical and gas
supplies. Contact Miele Technical Ser
-
vice.
Safety
~
The appliance is hot during use and
remains so for some time after being
switched off. Be careful not to touch the
appliance if it may still be hot.
~
Do not heat empty pots or pans.
This may cause damage to the
cookware and the surrounding area.
Danger of fire.
~
Do not leave the cooktop
unattended while in use. Boil-overs
cause smoking, and greasy spill-overs
may ignite.
~
Do not use water on grease fires.
Smother any fire or flame using a lid, or
use a dry chemical or foam-type
extinguisher.
,
WARNING - NEVER use this
appliance as a space heater to heat
or warm the room. Doing so may
result in carbon monoxide poisoning
and overheating.
~
Protect your hands with oven mitts
or potholders when using the
appliance. Use only dry, heat resistant
potholders. Moist or damp potholders
used on hot surfaces can result in
steam burns. Do not let the potholder
touch the hot heating elements. Do not
use towels or other bulky items near the
appliance.
IMPORTANT SAFETY INSTRUCTIONS
6
~
Do not flambé under an exhaust
hood. Flames could be drawn up into
the hood by the suction or the grease
filters may ignite.
~
Take care that drafts do not blow
flammable material toward the flames
or push the flames so that they extend
beyond the edges of the pan.
~
Only certain types of glass / ceramic
or other glazed cookware are suitable
for use on a cooktop without breaking
due to a sudden temperature change.
Verify with cookware manufacturer.
~
Be aware of loose fitting or hanging
garments while operating the cooktop,
they may present a fire hazard.
~
Be careful not to drop anything on
the ceramic surface. Even lightweight
objects may cause damage.
~
Only use cooking utensils suitable
for cooktop use.
~
Do not store items on the appliance
when not in use. Items could melt or
catch fire from residual heat or if the
appliance is turned on inadvertently.
Always switch the burner(s) off after
use.
~
Do not store aerosols, combustibles
or any other easily flammable materials
underneath or adjacent to the
appliance.
~
Do not use plastic or aluminium foil
on any part of the cooktop. It melts at
high temperatures. Fire hazard.
~
Do not heat unopened containers.
Built-up pressure may cause the
container to burst and result in injury.
~
Make sure all components of the
gas burner are assembled correctly
before using the cooktop.
~
Do not use pans that extend past
the burner grate. Using larger pans
may cause the flames to spread out
and damage the surrounding
countertop or other countertop
appliances.
~
For safety and stability, do not use
pans with a bottom diameter smaller
than the burner grate.
~
Only certain types of glass, ceramic
or other glazed cookware are suitable
for use on a combiset without breaking
due to the sudden temperature change.
~
Do not use containers made of
plastic or aluminium. They may melt at
high temperatures.
~
The burner grates supplied with the
appliance must always be used. Never
place a pan on the burner by itself.
~
Do not let cooking grease or other
flammable materials accumulate on the
appliance. Fire Hazard.
~
Place the grates on vertically to
prevent any scratches.
~
The use of a gas cooktop leads to
the formation of heat, moisture and
combustion products in the room where
the appliance is installed. Ensure
proper attention is paid to the
ventilation of the installation area:
windows kept open or a ventilation
hood installed and running.
IMPORTANT SAFETY INSTRUCTIONS
7
~
When using a portable appliance
near the cooktop, make sure that its
power cord does not come in contact
with the cooktop.
~
If there is a drawer directly
underneath the appliance without a
wooden base in between, ensure that
no aerosols, combustible liquids or
other easily flammable materials are
kept in it. If cutlery inserts are to be
placed in the drawer, they must be
made of a heat-resistant material.
~
Do not use roasting pans, frying
pans or grill stones large enough to
cover several burners. The resulting
heat accumulation can damage the
appliance.
~
If the gas cooktop is installed
behind a cabinet door, it must only be
used with the door open.
Only close the cabinet door when the
appliance is switched off.
~
If the gas cooktop has not been
used for an unusually long time, it
should be thoroughly cleaned before
using it again and checked that it is
working properly by an authorized
expert.
~
Before discarding an old appliance,
disconnect it from the gas and
electrical supply, and cut off the power
cord to prevent it from becoming a
hazard.
SAVE THESE INSTRUCTIONS
AND REVIEW THEM
PERIODICALLY
IMPORTANT SAFETY INSTRUCTIONS
8
Cooktop
a Fast burner
b Auxiliary burner
cd Normal burners
e Grates
f Burner symbols
Control knobs:
g Front right burner
h Right rear burner
i Left rear burner
j Front left burner
Guide to the appliance
9
Burners
Fast, Auxiliary and Normal burners
a Burner cap
b Burner head
c Burner base
d Ignition safety control
(Thermocouple)
e Ignitor
Guide to the appliance
10
Cleaning the cooktop
^
Remove any protective films.
^
Wash the removable parts of the gas burner in a mild
solution of warm water and liquid dish soap.
^
Dry and reassemble the parts in the correct order (see
"Cleaning and care").
^
Wipe the cooktop with a damp cloth and dry thoroughly.
Metal components have a protective coating which may give
off a slight odor the first time your new appliance is heated.
The harmless odor will dissipate after a short time and does
not indicate a faulty connection or appliance defect.
Before the first use
11
Control knobs
The control knob is used to turn on the burner and to regulate
the strength of the flame.
Fast, Auxiliary and Normal burners
ß The gas supply is turned off
& Highest flame
/ Lowest flame
Turning on
^ To light the burner, press the corresponding burner control
knob and turn it counterclockwise to the largest flame
symbol.
Pressing a burner control knob automatically generates a
spark at all burners on the cooktop. This is normal and
does not indicate a faulty appliance.
^
When a flame is visible, keep the burner control knob
pressed for5-10seconds, then release it.
^
If the flame goes out prematurely, turn the burner control
knob to "ß". Air out the room or wait at least 1 minute before
attempting to reignite. You may have to keep the burner
control knob pressed a little longer.
^
If the burner does not ignite even at the second attempt,
turn the burner control knob to "ß" and and see "Frequently
asked questions".
Operation
12
Turning on in the event of a power failure
If there is a power loss, you can ignite the flame manually,
e.g. with a match.
^
Press the burner control knob and turn it
counterclockwise to the largest flame symbol.
^
Keep the knob pressed and ignite the escaping gas-air
mixture with a match.
^
Keep the knob pressed for a further approx.5-10seconds
and then release it.
Regulating
The flame should be regulated so that it never protrudes
beyond the pot. Since the outer part of the gas flame is much
hotter than the center of the flame, the flame tips should
remain under the base of the pot. Protruding flame tips give
off unnecessary heat into the air and can damage pot
handles and increase the risk of burning.
The burner can be continuously regulated between the
highest and lowest flame.
^ To switch from the high to the low setting, turn the burner
control knob clockwise until resistance is felt. Press the
knob down until you pass the stop, and release the
pressure and set the cooktop the desired setting.
^
To switch from the low to the high setting, turn the burner
control knob counterclockwise until resistance is felt. Press
the knob down until you pass the stop, and release the
pressure and set the cooktop the desired setting.
Turning off
^
Turn the burner control knob clockwise to "ß".
The gas supply is stopped and the flame goes out.
Do not turn the burner control knob clockwise beyond "ß".
Operation
13
Select the cookware to match the burner:
large diameter = large burner
small diameter = small burner.
Using oversized pans may cause the flames to spread out
and damage the surrounding countertop or other
countertop appliances. The proper pan size will also
improve efficiency.
Pots with a smaller diameter than the pan support and pots
that do not sit securely (without wobbling) are hazardous
and should not be used.
Unlike pans used on an electric cooktop, the bases do not
need to be even for good results.
When buying pots and pans, keep in mind that it is
generally not the base diameter but the upper diameter
which is specified.
Only use heat-resistant cookware.
Thick pan bases will give more even results, as hot spots
are reduced due to better heat distribution.
Thin pan bases will conduct the heat faster but not as
evenly as thick pan bases. Stir the food frequently to
prevent burning.
Always place the cookware on the grate. The cookware
must not be placed directly on the burner.
Position the cookware on the grate so that it cannot tip
over. A minimum amount of wobbling can never be
completely ruled out.
Do not use pots or pans with edge-supported bases.
Cookware
14
If possible, cook in covered pots or pans. This prevents
unnecessary heat loss.
Cook with less water.
The cooking time can be significantly reduced by using a
pressure cooker.
After cooking or frying, promptly set to a lower flame.
Generally, wide / shallow pans will heat quicker and cook
more evenly than narrow / tall ones.
Energy saving tips
15
Ignition safety control
The appliance is equipped with an Ignition safety control.
This control cuts the gas supply if the flame goes out and
reignition is unsuccessful, e.g. from a boilover or a draft. Any
further escape of gas is prevented.
^
To reignite the burner knob clockwise to "ß" and then turn it
on as usual.
The Ignition safety control works independently of the power
supply. It is active if the appliance is in use during a power
failure.
Safety feature
16
,
Never use a steam cleaner to clean this cooktop.
Pressurized steam could cause permanent damage to the
surface and to components.
Do not use any sharp or pointed objects which could
damage the seal between the frame and the countertop.
Keep the ignitor in the burner dry. If it gets wet it will not
spark.
Dry your cooktop thoroughly after cleaning it to prevent
lime deposits.
Spills containing salt or sugar should be cleaned immedi
-
ately.
The surfaces of the burner parts and grates become
slightly duller over time. This is normal and does not
indicate any impairment of the material.
To better maintain your appliance avoid the following:
cleaners containing soda, ammonia, thinners, or chlorides,
cleaners containing descaling agents or lime removers,
abrasive cleaners,
stainless steel cleaners,
dishwasher soap,
caustic (oven) cleaners,
scouring pads, steel wool, hard brushes,
metal scrapers.
Glass cleaners may be used to clean the exterior.
However do not allow them to sit or "puddle", this can
cause damage to the surface. Remove the cleaner
promptly.
Cleaning and care
17
Cleaning Instructions
Ceramic
surfaces
Remove heavy dirt with a damp cloth and stubborn
dirt with a glass scraper.
Clean with the Miele ceramic surface and stainless
steel cleaner (see the Miele online store) and with
kitchen paper or a clean cloth.
Do not apply cleaner to a hot cooktop as this can
cause discoloration.
Wipe with a damp cloth and dry with a soft cloth.
Do not use liquid dish soap
as not all soiling and
residue will be removed.
This results in an invisible
film which causes
discoloration of the glass
ceramic. This discoloration
is permanent.
When using special
ceramic cleaning agents,
follow the instructions of the
manufacturer.
Grates Take out the grates.
Clean in the dishwasher or with a sponge cloth, a
mild solution of liquid dish soap and warm water.
If necessary, use the rough side of the sponge.
Bei hellen Stellen kann es
sich um Reinigerreste aus
der Spülmaschine oder um
Abrieb der Topfböden
handeln. Reinigen Sie wie
links beschrieben.
Burner control
knob
Clean with a sponge cloth, some liquid dish soap
and warm water.
Not dishwasher safe.
Burner Remove all loose parts of the burner.
Clean with a sponge cloth, a mild solution of liquid
dish soap and warm water.
Wipe the non-detachable parts of the burner with a
damp cloth.
Not dishwasher suitable.
Make sure that the flame
openings are completely
dry after cleaning.
Ignition safety
control
(thermocouple)
Wipe carefully with a well damp cloth. The Ignition safety control
(thermocouple) must not
become wet, otherwise it
will not spark.
Cleaning and care
18
Assembling the burners
Auxiliary, normal and fast burners
^ Place the burner head b on the burner base c so that the
thermocouple d and the ignitor e feed through the holes
of the burner head. The burner head must engage
properly.
^
Lay the burner cap a flat on the burner ring b.
The burner cap cannot shift if positioned correctly.
Make sure the burner parts are assembled in the right order.
Cleaning and care
19
,
Repairs should only be carried out by an authorized technician in
accordance with local and national safety regulations. Unauthorized repairs
could cause injury or appliance damage.
Problem Cause Solution
The burner does not
ignite after several
attempts
The burner is not assembled
correctly.
Assemble the burner correctly.
The gas valve is closed. Open the gas valve.
The burners are wet and soiled
and/or the flame holes in the
burners are soiled and clogged.
Clean and dry the burner.
The igniters are wet. Dry the igniters.
The cooktop is not plugged in
and the circuit breaker has
tripped.
Plug the cooktop in and restore power.
If lack of power is the problem, the cooktop
can be lit with a match. See “Turning on in the
event of a power failure”.
Gas flame goes out
after ignition
- Residue has been built up
between the ignitor and the
burner.
- The burners are assembled
incorrectly.
Clean the burners.
Position the burner parts correctly.
The shape of the gas
flame varies
The burner parts are not
positioned correctly.
Position the burner parts correctly.
The burner head or burner
cover holes are dirty.
Clean the burners.
The burner ignitor is
not working
The circuit breaker has tripped. Restore power.
If lack of power is the problem, the cooktop
can be lit with a match. See “Turning on in the
event of a power failure”.
There is food residue between
the ignitor and the burner cover.
Clean carefully (see "Cleaning and care").
Frequently asked questions
20
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40

Miele KM3010G Installation guide

Category
Hobs
Type
Installation guide

Miele KM3010G: The Miele KM3010G gas cooktop offers a variety of features to make cooking easier and more enjoyable. With its four burners, you can cook multiple dishes at once, and the cast-iron grates provide a stable surface for your pots and pans. The cooktop also features electronic ignition, so you don't have to worry about fumbling with matches or lighters. And the sleek design of the cooktop will complement any kitchen décor.

Here are some of the benefits of the Miele KM3010G gas cooktop:

  • Four burners for cooking multiple dishes at once
  • Cast-iron grates for a stable surface for your pots and pans

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI