Haier HLM-116B User manual

INSTRUCTION

INSTRUCTION MANUAL

MANUAL

W ATER

W ATER DISPENSER

DISPENSER

H LM

LM -116B

-116B

PRODUCT

PRODUCT AND

AND

AND DESCRIPTION

DESCRIPTION

SPECIAL

SPECIAL CAUTIONS

CAUTIONS

* This product belong to the type Ⅰ home appliance, this dispenser have to

connect with a three core socket which with a grounding wire. Or use the

e lectrical leakage protector.

* Please remember do not insert the plug of this dispenser into the socket

which used by some other home appliances or facilities together.

* If do not use the dispenser for long time, please disconnect the dispenser

with the electrical power.

* Do not make any changes on the plug yourself or prolong the power cord

yourself.

* The connecting way of the power cord: X type connecting, if the power cord

get damaged, must be changed by the professional maintenance person, do

not change the power cord by yourself.

* When the water dispenser is working, please do not allow the children play

with the dispenser, to avoid the hurt of the hot water.

OPERATION

OPERATION INSTRUCTIONS

INSTRUCTIONS

� Operation environmental temperature: 10 ℃ -42 ℃ .

� If the device is not applied for a long time, after the hot water cools down,

please remove the power plug and revolve the backside drainage cap to

drain the rest water in the hot tank then tighten the cap. Open the cold

water faucet to drain the rest water in the cold tank.

� If you do not plan to use the water heating function for more than three

days, we strongly recommend that you turn off the hot water function.

TAKING

TAKING DISPENSER

DISPENSER

DISPENSER OUT

OUT

OUT OR

OR SERVICE

SERVICE

� If the water dispenser will not be used for a long period of time, unplug the

power supply cord.

� Turn off the hot water.

� Drain the water through the faucets.

� Drain the water from tanks by drainage hole from the back of the

dispenser.

ATTENTIONS

� Do not use the bottle with any crack, leakage or holes.

� Do not set “ heating ” function until water comes out of hot water faucet to

prevent any damage on the heating tube.

� Never set “ heating ” function when there is no water.

� In the process of using, check the water tray frequently. If the water tray is

full, please pour the water out in time.

� Do not change the set of “ cooling ” between “ ON ” and “ OFF ” in three

minutes and protect the compressor and extend the compressor usage

life.

� This water dispenser is not recommended for outdoor use. Locate the

dispenser vertically and on the flat floor. Please keep the back side of the

dispenser more than 20 cm to the wall or other appliance, to make a better

heating emanating for the condenser of the dispenser .

� Locate the dispenser away from direct sunlight and sources of heat (stove,

heater, radiator, etc.).

� Keep the body of the dispenser clean , avoid the body of dispenser to be

scratched by the hard and sharp things.

� Please do not incline the dispenser more th a n 45 degrees when move it.

And also when mov e the dispenser, to avoid dropping and crash.

� Please do not locate the dispenser near the costly appliance or facility, like

the

TV,

DVD.

PREPA

PREPA RATION

RATION

RATION BEFORE

BEFORE

BEFORE FIRST

FIRST

FIRST OPERATION

OPERATION

� Before connecting the appliance to the power source. Let it stand upright

for approximately 2 hours. This will reduce the possibility of a malfunction

in the cooling system from handling during transportation.

The water dispenser is pre-cleaned at the factory but the reservoir and water

lines must be flushed with fresh water before use as follows:

1. Keep the unit unplugged.

2. Check and make sure the backside hot water drainage hole cap is not

leaked or broken.

3. Fill water tank with tap water full to capacity, wait for 5 minutes until

water settles.

4. Press the hot water faucet button until water comes out, then stop.

5. Plug the dispenser into the electrical socket . Press power ON/OFF

button. We are ready to complete the first cycle. In order to do that, wait

for the hot water to reach temperature (it will indicate ready with 3 beeps)

in approximately 10 minutes, and then wait for the cold to reach

temperature in other 40 minutes approximately (it will indicate ready

with 3 beeps).

6. Unplug the dispenser from the electrical outlet. Proceed to drain the

water from the faucets button, pressing hot water button and then cold

water button , until no more water remains. (to facilitate this operation,

use a large container)

7. Then, drain any water left in the tanks by opening the drain cap (stopper)

locates on the back side of the dispenser, until the left water drains

completely. Please do remember to close the drain cap(stopper) after

the drainage.

8. Then you could place a 5 gallon /3 gallon bottle of water on to the water

intake of the dispenser, allow water to stand for approximate one minute.

Or place a water purifier on to the water intake of the dispenser, then

pour tap water into the water purifier, also al low water to stand for

approximate on e minute to let the water flow into tanks.

9. Push water faucet buttons to insure water flows from both faucets.

10. Plug the dispenser back to electrical socket.

11.

Now you are ready to use your water dispenser.

ELECTRONIC

ELECTRONIC CONTROL

CONTROL

CONTROL :

For storage/refrigerator cabinet For sterilization cabinet

INS

INS TRUCTION

TRUCTION

TRUCTION OF

OF LCD

LCD

（ 1 ） In

In a

a Stand-by

Stand-by

Stand-by status

status

status : Press ON

ON button, the clock will display “ 00:00 ” or

present time and goes into stand-by status.

(2) Heating

Heating

Heating function

function

function : Heating indicator will flash on the display, when the

temperature reach to the setting temperature, the heating indicator will stop

flash and display steadily.

(3) Cooling

Cooling

Cooling function

function

function : Cooling indicator will flash on the display, when the

temperature reach to the setting temperature, the cooling indicator will stop

flash and display steadily.

(4) Boiling

Boiling

Boiling water

water

water heating

heating

heating function

function

function : Heating indicator and water temperature

will flash together, when the temperature of boiling water is 95 ℃ , the boiling

process return to original status.

(5) Ozone

Ozone

Ozone sterilization

sterilization

sterilization function

function

function (

(

( for

for

for sterilization

sterilization

sterilization cabinet

cabinet

cabinet only)

only)

only) : Ozone

sterilization indicator flash on the display, when the sterilization pause or stop,

the sterilization indicator display steadily.

(6) Anti-overheated

Anti-overheated

Anti-overheated display

display

display : when water dispenser is heating, if the hot tank

has no water, the water dispenser will stop heating, meantime the overheating

protection indicator flash (overheating protection indicator is heating indicator

and water temperature flash together). When the overheating protection

indicator flash, please fill water and reset, then the water dispenser wok

normally 。

（ 7 ） Low-temperature

Low-temperature

Low-temperature warm-keeping

warm-keeping

warm-keeping function:

function:

function: when water dispenser is

cooling, if cold water temperature lower than 3 ℃ , water dispenser stops

cooling automatically, meantime low temperature protection indicator flash(the

low temperature protection indicator is cooling indicator *and ℃ flash

together)please reset the power, then the water dispenser can work normally.

(8) Troubleshooting

Troubleshooting

Troubleshooting display

display

display : when the screen display Er

Er , if the heating

indicator does not display, it shows heating sensor meet problem, turn off to

check the equipment or change the sensor. If the cooling indicator does not

display, it shows cooling sensor meet problem, turn off to check the equipment

or change the sensor for solving problems.

2 INSTRUCTION

INSTRUCTION

INSTRUCTION OF

OF OPERATING

OPERATING

(1) Power(ON/OFF)

Power(ON/OFF)

Power(ON/OFF) : In a OFF status, press ON button, the screen will be in a

stand-by mode; when in a stand-by mode, press the OFF button, it will cut off

the power.

(2) Boiling/Set

Boiling/Set

Boiling/Set function

function

function : When dispenser is working, press this button and

goes into Boiling function. And press button again, quit boiling function. If press

this button over 2 seconds, it will goes into a Set

Set

Set mode. The screen will flash

following set sequence: HOUR （ clock set ） , MINUTE, HOT WATER

TEMPERATURE, COLD WATER TEMPERATURE, STERILIZATION MODE. If

not press above button over 8 seconds, the setting will finish.

(3) Night

Night

Night lamp

lamp

lamp (for

(for

(for storage

storage

storage or

or refrigerator

refrigerator

refrigerator cabinet)

cabinet)

cabinet) : Press this button, Night

lamp is On, press it once more, lamp is .Off.

Sterilizing/Night

Sterilizing/Night lamp

lamp

lamp (for

(for

(for sterilization

sterilization

sterilization cabinet

cabinet

cabinet only)

only)

only) : whenever press this

button, the water dispenser starts sterilizing progress. Press button again to

stop serilizing function. Press this button over 2 seconds, Night lamp is On,

press it over 2 seconds once more, lamp is .Off.

(4) Hot/+

Hot/+

Hot/+ : Press the hot button and start heating mode, press it once more and

quit heating. Press the hot button at the setting process, the number will

increase, press the button for 2 seconds more and goes into continuous

status.

(5) Cold/-

Cold/-

Cold/- :Press the cold button and start cooling mode, press it once more and

quit cooling, press the cold button at the setting process, the number will minus,

press the button over 2 seconds and goes into continuous status.

3 INSTRUCTION

INSTRUCTION

INSTRUCTION OF

OF FUNCTION

FUNCTION

(1)

(1) Clock

Clock

Clock set

set

a press ON 00:00 light

b press SET 00:00 hour flash

c press HOT/+ or COLD/- 06:00 set hour

d press SET 00:00 minutes flash

e press HOT/+ or COLD/- 06:23 set minutes

(2) Hot

Hot

Hot and

and

and cold

cold

cold temperature

temperature

temperature set

set

Press SET at the adjusting temperature flash, press HOT/+ or COLD/- set the

desired temperature. The hot temperature adjust between 70 ℃ and 90 ℃ ,the

cold temperature adjust between 5 ℃ and 15 ℃ (compressor cooling)or 10 ℃

and 15 ℃ (electrical cooling).

(3) Boiling

Boiling

Boiling function

function

Under any heating status, press BOILING/SET button and go into boiling

function. The set boiling temperature is 95 ℃ . When the temperature reach

95 ℃ , then quit boiling progress and return to original status. When the boiling

function is working, the Heating indicator and temperature will flash together.

(4) Sterilization

Sterilization

Sterilization function

function

function (

(

( for

for

for sterilization

sterilization

sterilization cabinet

cabinet

cabinet only

only

only )

)

Firstly put the items or goods into cabinet, close the cabinet door, then press

STERILIZTING/NIGHT LAMP over 2 seconds to start sterilization, when need

sterilization progress stop at the midway, press the button over 2 seconds and

quit the sterilization progress.

Sterilization setting have strong and weak two modes, the strong mode

time is 15 minutes and the weak mode time is 10 minutes. The selecting

method of strong and weak mode is: press SET button until the sterilization

indicator flash, press HOT/+ and COLD/- to select required sterilization mode.

During sterilizing process, please don ’ t open the cabinet avoiding the

leakage of ozone. After one hour of sterilizing, the goods can be taken out. The

sterilizing cabinet just can store small items, such as cup and tea.

CHECKING

CHECKING POSSIBLE

POSSIBLE

POSSIBLE PROBLEMS

PROBLEMS

PROBLEMS —

—

— DIY

DIY

In case the dispenser get some problems, before you sending the dispenser to the

maintenance place, you may checking the problems by yourself as follows:

Malfunction

phenomena

P ossible

ossible

ossible seasons

seasons

seasons Clear

Clear

Clear the

the

the problem

problem

1. The LCD screen

does not display

1. The electrical power has

not been connected well

2. the ON/OFF switch is

not on

1. Check if the plug inserted

into the power socket well

2. Check if the socket

connected with the power well

3. Turn on the switch

2. Big noise when the

dispenser is working

T he dispenser is not

located well

1. Make the dispenser be

located on flat fool

2. Do not let the back of the

dispenser lean on the wall

3. Press the left water

faucet button, no

water come out

There are some air left in

the hot water tank

1. Press the left faucet button

till water come out

2. Shake the dispenser gently .

4. Press the right

water faucet button,

no water come out

There are some air left in

the cold water tank

1.Press the right faucet button

till water come out

2. Shake the dispenser gently .

5. water leakage from

the head of top cover

The cap of the water bottle

is damaged

Contacting your bottle water

supplier

WIRING

WIRING DIAGRAM

DIAGRAM

CAUTION:

This appliance is not intended for use by persons (including children) with

reduced physical, sensory or mental capabilities, or lack of experience and

knowledge, unless they have been given supervision or instruction concerning

use of the appliance by a person responsible for their safety.

WARNING-Do not use mechanical devices or other means to accelerate the

defrosting process, other than those recommended by the manufacturer.

WARNING-Do not damage the refrigerant circuit.

WARNING-Do not use electrical appliances inside the food storage

compartments of appliance, unless they are of the type recommended by the

manufacturer.

WARNING-To avoid a hazard due to instability of the appliance, it must be

fixed in accordance with the instructions.

In order to ensure the water dispenser with enough stability, users should

follow below instructions to fix the unit:

1 .Children should be supervised to ensure that they do not play with the

appliance.

2 .Household used only

3 .Do not store explosive substances such as aerosol cans with flammable

propellant in this appliance.

4 .If the supply cord is damaged ， it must be replaced by the manufacturer ， its

service agent or similarly qualified persons in order to avoid a hazard.

Haier HLM-116B User manual

Related papers

Other documents