ReadyRemote 23927 Owner's manual

ReadyRemote
Brand
ReadyRemote
Model
23927
Type
Owner's manual

This manual is also suitable for

ReadyRemote 23927 is a remote car starter system that allows you to start your car remotely, as well as lock and unlock the doors, and open the trunk. The system also includes a panic button that can be used to sound the car's horn and attract attention in an emergency. The ReadyRemote 23927 is a convenient and easy-to-use system that can help you to stay safe and secure while on the go.

Here are some of the key features and benefits of the ReadyRemote 23927:

  • Remote start: Start your car from anywhere within range of the remote control.
  • Lock/unlock doors: Lock and unlock your car's doors with the press of a button.

ReadyRemote 23927 is a remote car starter system that allows you to start your car remotely, as well as lock and unlock the doors, and open the trunk. The system also includes a panic button that can be used to sound the car's horn and attract attention in an emergency. The ReadyRemote 23927 is a convenient and easy-to-use system that can help you to stay safe and secure while on the go.

Here are some of the key features and benefits of the ReadyRemote 23927:

  • Remote start: Start your car from anywhere within range of the remote control.
  • Lock/unlock doors: Lock and unlock your car's doors with the press of a button.
Read Me First!
23926, 23927 ADDENDUM
ADN23926.7 12-05, 23926, 23927 ADDENDUM © 2005 Directed Electronics—all rights reserved
Remote Car Starter De-initialization Instructions
The Remote Car Starter system that you have purchased has been initialized during our quality testing process and before proceeding with installation,
please, perform a simple de-initialization process following the steps below:
1. Locate main Power (Pink) and Ground (Black) wires using the diagram on the 1st page of your installation manual.
2. Connect ground wire to the Negative Battery Terminal (-) of your vehicle's battery.
3. Press and hold White Programming Button on the main remote car starter module.
4. Connect Power Wire to the Positive Battery Terminal (+) of your vehicle's battery while holding the White Programming Button (the LED will
illuminate).
5. Release the White Programming Button.
6. Disconnect Power wire from the Positive Battery Terminal (+) and wait until LED on the module goes out.
7. Reconnect Power wire to the Positive Battery Terminal (+). The LED will turn on and off.
8. Unit is now de-initialized, you can disconnect both Power and Ground wires from vehicle's battery and proceed with the installation using
the enclosed Installation Manual.
Note: Once you are done de-initialing the unit please make sure that the "In-gear" dipswitch mounted inside of the module (you will need to open a module
for that)is in the ON opposition, otherwise you will not be able to initialize the unit at the end of the installation. Please refer to a diagram in the Installation
Manual to locate the switch (page 4 for 23926 and page 5 for 23927).
Read Me First!
23926, 23927 ADDENDUM
ADN23926.7 12-05, 23926, 23927 ADDENDUM © 2005 Directed Electronics—all rights reserved
Remote Car Starter De-initialization Instructions
The Remote Car Starter system that you have purchased has been initialized during our quality testing process and before proceeding with installation,
please, perform a simple de-initialization process following the steps below:
1. Locate main Power (Pink) and Ground (Black) wires using the diagram on the 1st page of your installation manual.
2. Connect ground wire to the Negative Battery Terminal (-) of your vehicle's battery.
3. Press and hold White Programming Button on the main remote car starter module.
4. Connect Power Wire to the Positive Battery Terminal (+) of your vehicle's battery while holding the White Programming Button (the LED will
illuminate).
5. Release the White Programming Button.
6. Disconnect Power wire from the Positive Battery Terminal (+) and wait until LED on the module goes out.
7. Reconnect Power wire to the Positive Battery Terminal (+). The LED will turn on and off.
8. Unit is now de-initialized, you can disconnect both Power and Ground wires from vehicle's battery and proceed with the installation using
the enclosed Installation Manual.
Note: Once you are done de-initialing the unit please make sure that the "In-gear" dipswitch mounted inside of the module (you will need to open a module
for that)is in the ON opposition, otherwise you will not be able to initialize the unit at the end of the installation. Please refer to a diagram in the Installation
Manual to locate the switch (page 4 for 23926 and page 5 for 23927).
  • Page 1 1

ReadyRemote 23927 Owner's manual

ReadyRemote
Brand
ReadyRemote
Model
23927
Type
Owner's manual
This manual is also suitable for

ReadyRemote 23927 is a remote car starter system that allows you to start your car remotely, as well as lock and unlock the doors, and open the trunk. The system also includes a panic button that can be used to sound the car's horn and attract attention in an emergency. The ReadyRemote 23927 is a convenient and easy-to-use system that can help you to stay safe and secure while on the go.

Here are some of the key features and benefits of the ReadyRemote 23927:

  • Remote start: Start your car from anywhere within range of the remote control.
  • Lock/unlock doors: Lock and unlock your car's doors with the press of a button.
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents