Etec Moving Beam 7Q User manual

Brand: Etec

Model: Moving Beam 7Q

Type: User manual

Moving Beam 7Q

LED Beam Moving Head

User Manual

1.1 Unpacking

1.2 Safety Instructions

Carefully unpack the carton, check the contents to ensure that all parts are present,

and have been received in good condition. Contact your supplier immediately and

retain packing material for inspection if any part is missing or damaged.

1. INTRODUCTION

■

1 x Moving Beam 7Q

■

1 x Power Cord

■

1 x Mounting bracket

■

1 x User Manual

▪

The product is for indoor use only.

▪

Always turn off, unplug power and allow fixture to cool before servicing.

▪

Ensure that fixture is properly grounded.

▪

Please keep this User Guide for future consultation.

▪

Always make sure that you are connecting to the proper voltage and that the line

voltage you are connecting to is not higher than that stated on decal or rear panel of

the fixture.

▪

Always disconnect from power before servicing or replacing fuse.

▪

Make sure power cord is never crimped or damaged.

Warning!!! To reduce the risk of fire, electric shock, or injury to persons,

follow these important safety instructions:

The following items are included in the box:

Caution!

Avaid looking directly into the LED light beam at a close distance!

Thank you for selecting this LED moving head. With 7 x 15W RGBW 4in1 LEDs, it

produces

extremely bright beam and unlimited colors. Great for stage, club, bar, DJ,

etc. To optimize the performance of this product, please read the user manual

carefully before use.

1.3 Features

▪

LED beam effect

▪

DMX, Auto, Sound, M/S

▪

14 DMX channels

The Moving Head is fully operational in any mounting position, hanging upside-down,

side mounted, or set on a flat llevel surface, etc.

1.4 Product overview

2. SETUP

2.1 Mounting

▪

Linear dimmer 0 - 100%

▪

Various strobe 1-25 fps

▪

Pan/Tilt: 540° / 220°

▪

4-button LCD display

IMPORTANT!!! Safety cables must always be used when unit is celling or truss

mounted. The safety cable must be capable of holding 10 times the weight of the

fixture.

Control Panel

Power In/Out ON/OFFFuse

DMX In/Out

The fixture is designed to work on AC 100-240V 50-60Hz. All units must be powered

directly from a switched circuit. This unit cannot be run on a rheostat or dimmer

circuit even if used solely for a 0% to 100% switching.

2.3 AC Power

WARNING!!! All fixtures must be connected to circuits with a

suitable Earth Ground.

3.1 Menu Map

3. OPERATION INSTRUCTIONS

DMX Address DMX Address = 001

Built-in program

= 0 - 100%

Reset Default

Calibration

Manual control

Temperature = 000C

Auto Play

= Alone

= Master

= Alone

= Master

Sound activation

= ON / OFF

Code Code = 000

Pan Pan = 000

Tilt Tilt = 000

Red Red = 000

Green Green = 000

Blue Blue = 000

White White = 000

Pan Pan = 000

Pan fine Pan fine= 000

Tilt Tilt = 000

Tilt fine Tilt fine = 000

P/T speed Speed = 000

Dimmer Dimmer = 000

Strobe Strobe = 000

Red Red = 000

Green Green = 000

Blue Blue = 000

White White = 000

Slave

5 Sound sensitivity

= ON / OFF

3 Reverse Pan = ON / OFF

4 Reverse Tilt = ON / OFF

6 Special

7 Reset

3.2 DMX channels

14 DMX Channels

Channel

Pan 000-255

000-255

000-010

011-020

021-030

031-040

041-050

051-060

061-070

071-080

081-090

Pan fine

Tilt

Tilt fine

DMX Value & Functions

Pan movement

Fine control of Pan movement

Tilt movement

Fine control of Tilt movement

000-2555 P/T speed Pan/Tilt speed from high to low

Dimmer 0-100%

Red intensity 0-100%

Green intensity 0-100%

Blue intensity 0-100%

White intensity 0-100%

Strobe closed

Strobe speed from slow to fast

Strobe open

000-2556 Dimmer

7 Strobe

8Red

9 Green

11 White

000-009

010-250

251-255

10 Blue

12 Color Macro

13 Auto programs

14 Reset

No function

Red

Green

Blue

White

R+G

G+B

B+W

R+B

091-100

101-110

111-120

121-130

131-140

141-150

151-200

G+W

R+W

R+G+B

R+G+W

G+B+W

R+G+B+W

Color snap from slow to fast

201-255

Color cross fade from slow to fast

000-015

016-045

046-075

076-105

106-135

136-165

166-195

196-225

226-255

No function

Program 1

Program 2

Program 3

Program 4

201-225

6 seconds to reset

Program 5

Program 6

Program 7

Program 8

5. Specifications

Source: 7 x 15W RGBW 4in1 LEDs

Beam angle: 8°

Power consumption: 160W maximum

Fuse: F2A / 250V

Power supply: 100~240V, 50-60Hz

Dimensions: 267 x 168 x 304 mm

Weight: 4.8 kg

4. General Maintenance

a. Unscrew the fuse holder and remove the damaged fuse.

b. Replace with exact same type fuse and screw the fuse holder back in its place.

4.1 Fuse Replacement

MPORTANT INFORMATION!

In order to optimize the recovery and recycling of the materials

that old appliances contain and reduce the impact on human

health and the environment, ensure that this product is recycled

at the end of its life.

Etec Moving Beam 7Q User manual

Etec Moving Beam 7Q User manual

Etec Moving Beam 7Q User manual

Other documents