Mariner Waterproof Quad-Copter User manual

Brand: Mariner

Model: Waterproof Quad-Copter

Type: User manual

Instruction Manual

Mariner Waterproof Quad-Copter

● Basic Version

Dear customer:

Thank you for purchasing the Mariner waterproof quad-c op t e r. In order to quickly and safely master the operation of

Mariner, please read the user manual carefully and then keep it in a safe place for future consultation and reference.

1. Important statement

1). This product is not a toy. It’s a piece of complicated equipment which harmoniously integrates engineering materials,

mechanics, electronics, aerodynamic and high frequency radio. Correct installation and adjustment are necessary to

avoid accidents taking place. The owner must always operate in a safe manner. Improper operation may result in

serious property damage, bodily injury or even death.

2). We accept no liability for damage and consequent damage arising from the use of these products. As we have no

control over the way they are maintained, used and operated.

3). This product is suitable for experienced Aircraft pilots aged 18 years or more. All minors must be accompanied by a

responsible adult when flying.

4). The flight field should be legally approved by the local government. We accept no liability for any safety duties or

fines arising from operation, usage or miss-control after the sale of the products.

5). We consign our distributors to offer technical support and service after sale. Please contact the local distributors for

problem resolution caused by usage, operation, maintenance, etc.

2. Safety matters needing attention

Aircraft flight is a high risk hobby, whose flight should be kept far away from other people. Mis-assembled or broken

main frame, defective electronic equipment, and/or problematic radio system will lead to unforeseen accidents such as

bodily injury or property damage. The pilot MUST pay attention to the flight safety and UNDERSTAND his responsibility

for accidents caused by his carelessness.

2.1 Far away from obstacles and people

An Aircraft in flight has risk of uncertain flight speed and direction which is potentially dangerous. When flying, please

keep your Aircraft far away from people, high buildings, high-tension lines, etc.

2.2 Proper operation and maintenance

Please use FPVfactory original spare parts to upgrade, modify or maintain your Aircraft in order to ensure its safety.

Please operate your Aircraft within the range of functions permitted. It is forbidden to use it outside of the safety laws

or regulations.

2.3 Avoid flying alone

At the beginning of learning about radio-controlled flight, there are some difficulties to overcome. Please avoid flying

alone. Invited experienced pilots to guide you (two of the most effective methods to practice are via a PC flight

simulator and/or under the supervision of a skilled pilot).

2.4 Safe operation

Please fly your Aircraft according to your physical status and flight skills. Fatigue, listlessness and miss-operation will

increase the possibilities of accidental hazard.

2.5 Away from highly sinning parts

Please keep pilot, people and object away from the spinning blades.

2.6 Protect from heat

An Aircraft is made from metal, fiber, plastic and electronic components etc. Please keep away from heat in order to

avoid distortion, even damage, caused by high temperatures.

3. Attention before flight

3.1 Ensure the battery packs of both transmitter and receiver are fully charged (saturated).

3.2Ensure both the throttle stick and the throttle trim of your transmitter stay at the lowest positions before operation.

3.3Please strictly obey the order of turn-on and turn-off before operation. When starting your flight, please turn on

your transmitter first, and connect the power cable of your Aircraft last. When finishing your flight, please disconnect

the power cable of your Aircraft first, and turn off your transmitter.

3.4 An upset in the order of connection may cause your Aircraft to lose control. Please cultivate a correct habit of

turn-on and turn-off.

4. What’s in the box

Mariner*1, Motors*4, ESCs*4, Power distribution board*1, Extra landing gear*1, Propellers*4, Top cover-seal*1, Top

cover-unseal*1, Manual*1

5. Product diagram

6. Propeller installation

6.1Look at the direction of the propellers and insure

they are installed correctly.

6.2 There is “1238R” mark in the propeller,

means this is a clockwise propeller. There is “1238”

mark in the propeller, means this is a anti-clockwise

propeller.

6.3 To insure proper fit of the propellor on the motor,

use one of the included black bushings.

(Two tips: 1. propeller side with letter of “1238R or 1238” is on the top; 2. The Wind generated by propeller goes

down to ground). Use the red anodized nutto attach the propeller to the motor.

(Note: A small open end wrench has been included to tighten the propeller nut.)

7. UBEC connection

UBEC is a small electronic module for providing power

to the receiver and fly control system. It needs a free

channel from RC receiver.

If you use DJI flight control unit or other type of flight

control unit with power module, then you don’t need to

install this UBEC.

8. Connect the indication board to battery

There are 4 super bright REDs on the arms of Mariner.

The RED ones on the front, while GREEN ones on the

rear. The LED help to indicate important functions the

Mariner no matter in day time or in night time. It also

provides a battery status alerts by flashing when the

LiPo battery is low.

The LED board has a 7-pin connector (GND, B1, B2, B3,

B4, B5, B6). The LED boardcan detect the voltage up to

a 6-cell, (6S), battery. Make sure the Black GND line of

battery connects to the GND pin of the LED board.

9. Landing arm and gimbal installation

9.1 Mariner comes with 4super flexible Nylon landing arms, These landing arms are made from a strong engineering

thermoplastic and can survive moderate crashes and hard landings. Use of the landing arm is necessary when carrying a

camera or gimbal system.

9.2 The Mariner has 4 screw holes with metal insertion the bottom. These screw holes can be used to attach a gimbal

or camera mount. They are not necessary if you use an adhesive camera mount like that provided by GoPro and other

small HD sport camera.

10. Main specification

Body Diameter：500mm;

Body Height：120mm ;

Wind Diameter:755mm ;

Propeller Type:1238;

Propeller Length:30.5mm ;

Weight:1150g ;

Max take-off Weight:>2000g ;

Motor Type: 4215/650kv ;

ESC:40A ;

Battery: 2500mah/ 4S/ 25C /14.8V

For more information of our products, please visit www.fpvfactory.com or www.moogu.cn

Mariner Waterproof Quad-Copter User manual

Brand: Mariner

Model: Waterproof Quad-Copter

Type: User manual

Download PDF

report

Mariner Waterproof Quad-Copter User manual

Mariner Waterproof Quad-Copter User manual

Other documents