Stelpro ARWF1002 User manual

Brand: Stelpro

Model: ARWF1002

Category: Space heaters

Type: User manual

This manual is also suitable for

INSARWF0314

USER’S gUidE

ARWF SERiES

WALL FAN HEATER

REPLACEMENT COMPONENT LIST INCLUDED

For further information or to consult this guide online, please visit our website at www.stelpro.com

This unit

complies with

the CSA and

UL standards

HISTORIQUE DES RÉVISIONS | REVISIONS HISTORY

REV. DATE DESCRIPTION MODIFIÉ PAR | MODIFIED BY:

MATÉRIEL | MATERIAL :

1 / 1

# PIÈCE | PART # :

RWF

FEUILLE | SHEET :

X:\01_PRODUITS\FAMILLES\RWF\DOCUMENTATION\RWF_ISO.dft

TROISIÈME ANGLE DE

PROJECTION

THIRD ANGLE PROJECTION

FORMAT | SIZE :

DESCRIPTION :

AÉROCONVECTEUR MURAL

EMPLACEMENT:

TOLÉRANCES SI NON-SPÉCIFIÉES | TOLERANCES IF NOT SPECIFIED

ANGULAIRE | ANGULAR:

±.03"

±.015"

.XX

.XXX

[ ±.76mm ]

[ ±.38mm ]

±1°

±0.5°

XX°

XX.X°

lboujida

2005-12-01

2013-09-24 / bcloutier

LINÉAIRE | LINEAR:

CRÉÉ LE | CREATED ON :

CRÉÉ PAR | CREATED BY :

MIS À JOUR | UPDATED :

L'INFORMATION CONTENUE DANS CE

DOCUMENT EST LA PROPRIÉTÉ DE

STELPRO DESIGN. EN AUCUN CAS,

L'INFORMATION NE PEUT ÊTRE

UTILISÉE, SAUF SOUS AUTORISATION

ÉCRITE DE STELPRO DESIGN.

THE INFORMATION IN THIS DOCUMENT

IS THE PROPERTY OF STELPRO DESIGN.

IN ANY CASE, THE INFORMATION CAN'T

BE USED, EXCEPT BY THE WRITTEN

CONSENT OF STELPRO DESIGN.

INSARWF0314

AVERTiSSEMENT

Before installing and operating this product, the user and/or installer must read, understand and follow these instructions and keep them handy for future refe

rence. If these instructions are not followed, the warranty will be considered null and void and the manufacturer deems no further responsibility for this product.



, according to the 

effective in your region.

The following instructions must be adhered to in order to avoid personal injuries or property damages, serious injuries and potentially fatal electric shocks.

Protect the heating unit with the appropriate circuit breaker or fuse, in accordance with the nameplate.

Make sure the line voltage (volt) is consistent with that indicated on the unit’s nameplate.

This unit must be

.

Switch off the power at the circuit breaker/fuse before installing, repairing and cleaning the unit.

Make sure the unit is appropriate for the intended use (if needed, refer to the product catalog or a representative). Use this heater only as described in this







It corresponds to 

-

quired capacity to heat a room. If needed, refer to a specialist who will be able to calculate these heat losses and optimize the required capacity or consult the



to install several units instead of one. For example, 2 X 1000 W rather than 1 X 2000 W.





 indicated in the installation section.





Moreover, do not turn it on or off when standing in water or if your hands are wet.

When mounting the unit, make sure that the anchorage used can support the total weight of the unit with the mounting brackets.

When cutting or drilling into a wall, do not damage electrical wiring and other hidden utilities.





Because this unit is hot when in use, it may pose risks even in normal operation. Therefore, be careful and responsible when using it. To avoid burns, do not

let bare skin touch hot surfaces. Let the unit cool down for a few minutes before handling it (it stays warm for some time after shut-down). Extreme caution is

necessary when any heater is used by or near children or invalids and whenever the heater is left operating and unattended.

from the front of the

heater and away from the side and rear.



Never block air vents (with objects or other items). You risk damaging the heater and the obstruction could lead to electric shock or overheating, which could









products. Store it in a dry place.

Some areas are dustier than others. Thus, it is the user’s responsibility to evaluate if the unit must be cleaned based on the amount of dirt accumulated on



accordance with these instructions.

The thermal protection activation indicates that the unit has been subjected to abnormal operating conditions so the light shall lit up. If the thermal protection



to make sure it is not damaged. (Refer to the limited warranty).

Before unplugging the unit, all controls must be in the “OFF” position and the current from the main breaker panel should be cut. (The general switch may be



repair centre. (Refer to the limited warranty)

Make sure that all the electrical connections are secure and have been made properly. Pull each wire to ensure it is not loose in the connector or the terminal



If an option must be added, make sure it has been approved by Stelpro. This way, it will ensure that it has been tested in accordance with our safety rules and

that an appropriate installation has been planned into the unit.



instances, the instruction manual may not entirely match all the functions of the actual product. Therefore, the actual product and packaging, as well as the name

and illustration, may differ from the manual.

WARNiNg





INSARWF0314









          

   



Keep the front and and upper sides of the unit at least 3 feet (91 cm) from any adjacent surfaces.

Moreover, make sure objects or pieces of furniture such as, but not limited to, blankets, towels,



into contact with the unit and keep them at least 3 feet (91 cm) from the unit. Failure to comply



make sure those near the unit can withstand heat.

TECHNICAL DRAWINGS

INSTALLATION

SPECIFICATIONS

SPECS, TECHNICAL DRAWINGS & INSTALLATION



      



120, 208, 240, 277 V  6 LB/2.7 KG 3 1/4”/82 MM 8 11/16”/220 MM 17 1/8”/435 MM







FRONT

TOP

8 11/16"

220mm

17 1/8"

435mm

6 3/8"

163mm

14 9/16"

370mm

1 5/16"

34mm

3/4"

19mm

2 3/8"

60mm

2 7/8"

72mm

2 11/16"

68mm

3/4"

20mm

203mm

7/8"

22mm

7/8"

22mm

3 3/16"

80mm

13/16"

21mm

INSARWF0314

Available Products with Dual Power

   

ARWF1001 1000W 500W 120V

ARWF1008 1000W 500W 208V

ARWF1002 1000W 500W 240V

ARWF1501 1500W 750W 120V

ARWF1508 1500W 750W 208V

ARWF1502 1500W 750W 240V

ARWF2008 2000W 1000W 208V

ARWF2002 2000W 1000W 240V

TO CHANGE POWER OF UNIT

Before doing the following connections, make sure to turn off the fuse/breaker supplying the circuit.

High Power Setting

- Refer to related wiring examples to complete the connection to the cable coming from the circuit breaker and the thermostat (if needed).

- Wires A and B are connected together.

                 

connected to the ground wire coming from the circuit breaker cable. In the unit, use the green screw to connect the ground wire from the cable.



each wire and make sure they cannot come out of the wire nut.

- Once all these steps are performed, you can turn on the circuit breaker safely.

Low power setting

- Refer to related wiring examples to complete the connection to the cable coming from the circuit breaker and the thermostat (if applicable).

- Only wire A is connected. So, remove wire B and put a wire nut on its tip.

connected to the ground wire coming from the circuit breaker cable. In the unit, use the green screw to connect the ground wire from the cable.

each wire and make sure they cannot come out of the wire nut.

- Once all these steps are performed, you can turn on the circuit breaker safely.

Important : Light

Activation of the thermal protection is indicated by a light. It warns you that the heater has been subjected to

abnormal conditions. If this occurs, it is highly recommended that the unit be disconnected and inspected by a



INSTALLATION OF THE BACK BOX IN A NEW BUILDING









3. Position the back box on the appropriate stud or joist location and secure it using two nails or screws.

4. Remove one knockout in the back box to allow for the entry of the power supply cable.

5. Bring the power supply cable to the back box. Install a cable clamp and route the cable into the back box, leaving at least 6” (152mm) of cable

inside the back box for connection to the unit’s lead wires.

6. Put back the fan deck (4 screws).

* To facilitate installation with a surface cabinet, secure the heater to the wall, then place the cabinet and the grill together. Place the top screw

in line with the mounting hole. Lastly, install the second screw.

INSTALLATION & OPERATION

OPERATION

the heater must be properly installed before it is used.

INSARWF0314

THERMOSTAT

L1 L2

High Power Low Power

BLACK

GROUND

RED

BLACK

GROUND

RED

GROUND

BLACK

RED

GROUND

BLACK

RED

GROUND

BLACK

RED

GROUND

BLACK

RED

THERMOSTAT

GROUND

BLACK

RED

THERMOSTAT

L1 L2

GROUND

BLACK

RED

THERMOSTAT INSTALLATION - DOUBLE POLE INTERNAL

THERMOSTAT INSTALLATION - SINGLE POLE EXTERNAL

THERMOSTAT INSTALLATION - DOUBLE POLE EXTERNAL

THERMOSTAT INSTALLATION - SINGLE POLE INTERNAL

INSTALLATION

INSARWF0314

       

        

         

         

          



Use a soft rag for dusting. When cleaning, use only a damp rag and

         

 

dusty location, use a vacuum brush to remove dust and other foreign

objects from the grilles. Note that cigarette smoke could yellow the

discharge grille and that the best way to prevent this problem is to

clean the unit regularly.









MAINTENANCE

 

The unit does not work

 

 Open circuit breaker or fuse

 Activated thermal protection

 Faulty connections

The unit runs continuously

 

 

The enclosure is extremely hot

 

 Blocked air vents

 

The unit cycles under control of the thermal protection

(overheat indicator)

 Blocked air vents

 

Overheating

 

 

The breaker trips when the heater is turned on

 Faulty connections

 Voltage higher than indicated on the nameplate

Elements are on, but the motor does not work  

The desired room temperature cannot be reached

 One or more defective elements

 

 Voltage lower than indicated on the nameplate

 

N.B. If you do not solve the problem after checking these points, cut off the power supply at the main electrical panel and contact our customer service (see the

“Limited warranty” section to obtain the phone numbers).

TROUBLESHOOTING

MAINTENANCE & TROUBLESHOOTING

INSARWF0314

  

1 BOUT-019 

1 BOUT-021 

1 BOUT-020 

2 SB-005 

3 ELF-RWF001 ELEMENT (KIT) 500W-120V/1500W-

208V/2000W-240V

3 ELF-RWF002 ELEMENT (KIT) 0750 W-240 V

3 ELF-RWF003 ELEMENT (KIT) 0500 W-240 V

3 ELF-RWF004 ELEMENT (KIT) 1000 W-120 V

3 ELF-RWF005 ELEMENT (KIT) 500/1000 W-240 V

3 ELF-RWF006 ELEMENT (KIT) 1250 W-240 V

3 ELF-RWF007 ELEMENT (KIT) 1000 W-240 V

3 ELF-RWF007 ELEMENT (KIT) 750 W-208 V

3 ELF-RWF008 ELEMENT (KIT) 1500 W-240 V

3 ELF-RWF009 ELEMENT (KIT) 1500 W-120 V

3 ELF-RWF010 ELEMENT (KIT) 2000 W-208 V

3 ELF-RWF014 ELEMENT (KIT) 500 W-347 V

3 ELF-RWF015 ELEMENT (KIT) 750 W-347 V

3 ELF-RWF016 ELEMENT (KIT) 1000 W-347 V

3 ELF-RWF017 ELEMENT (KIT) 1250 W-347 V

3 ELF-RWF018 ELEMENT (KIT) 1500 W-347 V

3 ELF-RWF019 ELEMENT (KIT) 2000 W-347 V

3 ELF-RWF020 ELEMENT (KIT) 750/1500 W-240 V

3 ELF-RWF021 ELEMENT (KIT) 1000/2000 W-240 V

3 ELF-RWF022 ELEMENT (KIT) 500 W-277 V

3 ELF-RWF023 ELEMENT (KIT) 750 W-277 V

3 ELF-RWF024 ELEMENT (KIT) 1000 W-277 V

3 ELF-RWF025 ELEMENT (KIT) 1250 W-277 V

3 ELF-RWF026 ELEMENT (KIT) 1500 W-277 V

3 ELF-RWF027 ELEMENT (KIT) 2000 W-277 V

3 ELF-RWF028 ELEMENT (KIT) 500/1000 W-120 V

3 ELF-RWF029 ELEMENT (KIT) 750/1500 W-120 V

3 ELF-RWF030 ELEMENT (KIT) 500/1000 W-208 V

3 ELF-RWF031 ELEMENT (KIT) 750/1500 W-208 V

3 ELF-RWF032 ELEMENT (KIT) 1000/2000 W-208 V

3 ELF-RWF033 ELEMENT (KIT) 1250 W-120 V

3 ELF-RWF034 ELEMENT (KIT)750 W-120 V

  

3 ELF-RWF035 ELEMENT (KIT)1000 W-208 V

3 ELF-RWF036 ELEMENT (KIT)500 W-208 V

3 ELF-RWF037 ELEMENT (KIT)1250 W-208 V

4 M-RWF13Z* GRILLE

5 BLA-001 

6 MO-001 MOTOR 500-1000 W 208 V

6 MO-001 MOTOR 1250-2000 W-240 V

6 MO-002 MOTOR 500-1000 W-240 V

6 MO-010 MOTOR 500-1000 W 120 V

6 MO-011 MOTOR 1250-2000 W 208 V

6 MO-012 MOTOR 1250-2000 W-120 V

7 PROT-006 

7 PROT-005 

8 ST-017 

8 ST-013 

9 M-RWF00A0 

10 PL-240 

* Add W for white and A for almond

REPLACEMENT COMPONENT LIST

INSARWF0314

STELPRO DESIGN INC. | Saint-Bruno-de-Montarville | Quebec | J3V 6L7





, Stelpro warrants its products and their components against

   

 This warranty applies only to the original

purchaser; it is non-transferable and cannot be extended.



If at any time during the warranty period the unit becomes defective, you must cut off the power supply at the main electrical panel and contact 1) your

installer or distributor, 2) your service center or 3) Stelpro’s customer service department. In all cases, you must have a

 and

provide the

. Stelpro reserves the right to examine or to ask one of its representatives to

examine the product itself or any part of it before honoring the warranty. Stelpro reserves the right to replace the entire unit, refund its purchase price

or repair a defective part. Please note that repairs made within the warranty period must be authorized in advance in writing by Stelpro and carried out

by persons authorized by Stelpro.



 (electricians and distributors - French),  (electricians and distributors - English), or 

(consumers). The authorization number must be clearly written on the parcel or it will be refused.



This warranty is exclusive and in lieu of all other representations and warranties (except of title), expressed or implied, and Stelpro expressly disclaims



Stelpro’s liability with respect to products is limited as provided above. Stelpro shall not be subject to any other obligations or liabilities whatsoever,

whether based on contract, tort or other theories of law, with respect to goods or services furnished by it, or any undertakings, acts or omissions

relating thereto. Without limiting the generality of the foregoing, Stelpro expressly disclaims any liability for property or personal injury damages,

           

services, shutdowns, slowdowns, or for other types of economic loss or for claims of a dealer’s customers or any third party for such damages. Stelpro





of maintenance, improper maintenance (other than that prescribed by Stelpro) or a use other than that for which the unit was designed; 3) a natural

disaster or an event out of Stelpro’s control, including, but not limited to, hurricanes, tornadoes, earthquakes, terrorist attacks, wars, overvoltage,



negligence of the user or owner of the product. Moreover, it does not cover the cost of disconnection, transport, and installation.

The warranty is limited to the repair or the replacement of the unit or the refund of its purchase price,

. Any parts

replaced or repaired within the warranty period with the written authorization of Stelpro will be warranted for the remainder of the original warranty

period. This warranty will be considered null and void and Stelpro will have the right to refuse any claims if

 without