Gamber-Johnson Zebra TC8000/TC8300 Non-Powered Cradle Installation guide

Gamber-Johnson
Brand
Gamber-Johnson
Model
Zebra TC8000/TC8300 Non-Powered Cradle
Type
Installation guide

This manual is also suitable for

Gamber-Johnson Zebra TC8000/TC8300 Non-Powered Cradle is a rugged and reliable docking solution designed to securely hold and charge your Zebra TC8000 or TC8300 mobile computer. This cradle is constructed from high-quality materials and features a durable design that can withstand the rigors of everyday use. The cradle's non-powered design means that it does not require any external power source, making it ideal for use in vehicles or other mobile environments.

The cradle's ergonomic design makes it easy to insert and remove your mobile computer with one hand, even while wearing gloves. The cradle also features a built-in cable management system that helps to keep your cords organized and out of the way.

Gamber-Johnson Zebra TC8000/TC8300 Non-Powered Cradle is a rugged and reliable docking solution designed to securely hold and charge your Zebra TC8000 or TC8300 mobile computer. This cradle is constructed from high-quality materials and features a durable design that can withstand the rigors of everyday use. The cradle's non-powered design means that it does not require any external power source, making it ideal for use in vehicles or other mobile environments.

The cradle's ergonomic design makes it easy to insert and remove your mobile computer with one hand, even while wearing gloves. The cradle also features a built-in cable management system that helps to keep your cords organized and out of the way.

© Copyright 2019 Gamber-Johnson, LLC
PS-001
Printing Spec:
each individual product.
7160-1277, -01, & -02
TC8000 docking station and cradle
Rev A INST-923
This instruction sheet is for the Zebra TC8000 docking station and cradle only. For
instructions on features, set-up, and operation of the Zebra TC8000 handheld computer,
please refer to the manual provided by Zebra with the computer.
This docking station is designed to be used with a variety of Gamber-Johnson mounting
systems. Installation instructions for other Gamber-Johnson products are provided with
1/6
Form
If you need assistance or have questions, call Gamber-Johnson at 1-800-456-6868
RevisionProduct
INSTALLATION INSTRUCTIONS
Product Mounting Disclaimer
Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage
of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson
products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brake lines, electrical, drive train or other systems), air-bags and other safety equipment is
required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with original vehicle manufactures specifications
and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.
THUMB LATCH
LOCK
MAIN HOUSING
connector cable
attaches to Power wire
pigtail or USB hub
#10-32 MOUNTING
SCREWS
(AMP'S MOUNTING
HOLE PATTERN)
Opening the docking station will void the product warranty.
2/6
software issues are resolved prior to installation:
Test the docking station to ensure that it is working properly.
File these instructions in a safe place and refer to them when performing maintenance or re-
installing.
WARNING: Failure to follow all safety precautions and instructions may result in property damage,
serious injury, or death.
Conduct a "Bench Test"
prior to the actual install to verify that mounting locations are safe and practical.
PRE-INSTALLATION RECOMMENDATOINS
Gamber-Johnson strongly advises a "bench test" be conducted to verify all electronic and
Gamber-Johnson recommends positioning of all mounts and equipment in the vehicle
operating in the dock and battery is charging.
2. Insert computer into the docking station and verify that the computer is
1. Make sure the computer is operational by itself.
During Installation:
DO NOT connect this docking station to the vehicle battery until:
All other electrical connections are made1.
Mounting of all components is complete2.
Verification that no shorts exist in the entire system3.
DO NOT install equipment or route wiring or cords in the deployment path of any air bag.
When drilling into the vehicle, DO make sure that both sides of the surface are clear of anything that
could be damaged.
CAUTION: If wiring is shorted to the frame, high current conductors can cause hazardous sparks
resulting in electrical fires or flying molten metal.
After installation:
Safety is dependent on the proper installation and servicing of this docking station. It is important to
read and follow all instructions before installing this product.
To properly install a Gamber-Johnson docking station you must have a good understanding of
automotive electrical procedures and systems, along with proficiency in the installation and service of
aftermarket vehicle equipment.
There are no adjustments required at any time of the electrical components within the docking station.
IMPORTANT SAFETY INFORMATION FOR INSTALLERS
7160-1277-01
Power Only Cradle
Attach the power wire pigtail (7100-0445)
to the connector cable. Then plug the
5Vdc output power supply into the power
wire pigtail and secure with electrical tape.
GJ# 7400-0013 = 12-32Vdc input
GJ# 7400-0014 = 20-60Vdc input
GJ# 7400-0015 = 72-110 Vdc input
3/6
TC8000 Dock Options
7160-1277
Non Powered Cradle
7160-1277-02
Dock to be used in conjunction with the
Zebra USB hub #SHARE-USBH-01
(purchased separately from Zebra). Attach
the connector cable to the USB hub and the
12-24Vdc ouput power supply to the USB
hub and secure with electrical tape.
GJ# 16411 = 12-32Vdc input
GJ# 16412 = 20-60Vdc input
GJ# 16515 = 72-110Vdc input
GJ# 7160-1261
7160-1277-02 - Mounted with a
Connector cable
mating connector
the side
Hub positioned to
(purchased from Zebra)
SHARE-USBH-01 hub
Power supply
mating connector
Hub positioned to
the top
SHARE-USBH-01 hub
(purchased from Zebra)
4/6
TC8000 Mounting Options
The TC8000 docking station has the AMP's (30mm x 38mm) hole pattern.
7160-1277-01 - Mounted with a
GJ# 7160-0420
7160-1277-01 - Mounted with a
GJ# 7160-0357
scanner handle.
the scanner into the dock
until the spring loaded latch
below the trigger.
above with your fingers
Hold the scanner as shown
pops over the front surface
to hold it in place.
scanner into the dock at
pins are located.
top inside edge where the
Push upward until it hits the
approx. a 45 deg. angle
Place the top end of the
Lower the handle portion of To remove the scanner,
push the thumb latch to the
left and pull outward on the
5/6
Docking and Undocking the Computer
may cause undesired operation.
Dock-Zebra-TC8000 - Power Only Cradle
Regulatory Certification Information
Regulatory Model #: 7160-1277
GJ Model #'s: 7160-1277, 7160-1277-01, 7160-1277-02
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions. (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interfernece that
6/6
Dock-Zebra-TC8000 - Dock for use with USB Hub
•
ROHS: 50581: 2012 ROHS2 DIRECTIVE 2011/65/EU•
Certifications:
EN 55032: 2012/AC: 2013•
EN 50498: 2010•
VCCI-CISPER 32: 2016•
AS/NZS CISPER 32: 2015•
FCC PART 15 B: CLASS B•
ICES-003: 2017•
EN 50498: 2010•
ISO 10605, SECTION 8, TABLE C.2
Descriptions: Dock-Zebra-TC8000 - Cradle Only
Gamber-Johnson LLC, 3001 Borham Ave., Stevens
Point, WI, 54481, USA, 715-344-3482
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

Gamber-Johnson Zebra TC8000/TC8300 Non-Powered Cradle Installation guide

Gamber-Johnson
Brand
Gamber-Johnson
Model
Zebra TC8000/TC8300 Non-Powered Cradle
Type
Installation guide
This manual is also suitable for

Gamber-Johnson Zebra TC8000/TC8300 Non-Powered Cradle is a rugged and reliable docking solution designed to securely hold and charge your Zebra TC8000 or TC8300 mobile computer. This cradle is constructed from high-quality materials and features a durable design that can withstand the rigors of everyday use. The cradle's non-powered design means that it does not require any external power source, making it ideal for use in vehicles or other mobile environments.

The cradle's ergonomic design makes it easy to insert and remove your mobile computer with one hand, even while wearing gloves. The cradle also features a built-in cable management system that helps to keep your cords organized and out of the way.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents