Graco 356-08-42 - Lauren Dressing Table Assembly Instructions Manual

Brand: Graco

Model: 356-08-42 - Lauren Dressing Table

Type: Assembly Instructions Manual

This manual is also suitable for

A S S E M B L Y I N S T R U C T I O N S

PRINTED IN CHINA

HARDWARE AND TOOLS DIAGRAM

LaJobi Industries. - 257 Prospect Plains Rd. Cranbury,NJ 08512-Phone: 888-266-2848

Bulletin No. A-DT00-00

Dressing Table

Adult assembly required.

Small parts may present a choking hazard prior to assembly.

PARTS LIST

REF. PART NAME QUANTITY

A. Headboards 2

B. Non-grooved Rails 2

C. Wide Grooved Rails(Top) 2

D. Grooved Rails(Middle/Bottom) 4

E. Thick Shelf(Top) 1

F. Thin Shelves(Middle/Bottom) 2

G. 1-3/4 " Bolts 16

H. 3/4 " Bolts 2

I. Nylon Washers 2

J. Nuts 2

K. Allen Wrench 1

L. Wood Dowels 4

M. Casters 4

N. Restraint Harness 1

O. Foam Pad 1

Enclosed please find simple step-by-step instructions to help you quickly assemble your product. Before you begin we

recommend that you follow the steps below:

1. Please read the instructions thoroughly

2. Identify all parts and hardware, and

3. You will need the following tools:

Philips Head screw driver

Flat head screw driver

Hammer

Pliers.

To protect your parts during assembly please place them on a soft surface. To clean surface use only water on a damp cloth.

Do not use window cleaners or cleaning abrasives as it will scratch the surface and could damage the protective coating.

1-3/4" Bolt

Nylon Washer

Model shown is example only.

Styles may vary.

Restraint Harness

Foam Pad

Casters

Wood Dowel

Nut

Allen Wrench

3/4" Bolt

BULLETIN NO. A-FCI00-00

Furniture Care Instructions

Room Climate Control

Wood, when first cut contains more than 50 percent water. When it is prepared for furniture

construction

it is placed in a Kiln and the moisture content is brought down to 8 to 10 percent. Wood

porous and responds to its environment. If the room has high humidity it will absorb it and expand

and if the humidity is low it will lose moisture and shrink.

It is important that the humidity levels in the room be controlled from extremes of too much

humidity or too little. Furniture should not be placed close to air-conditioning outlets, fire places,

radiators, space heaters, humidifiers or dehumidifiers. Exposure to extreme variations of

temperature and humidity can damage any fine wood product.

The Ideal Environment for Fine Furniture

Fine wood furniture will have fewer problems when its environment is controlled at a temperature

between 65 and 75 degrees and a relative humidity between 35 and 40 percent. Wood placed in an

vironment out side of those limits can and will shrink or expand and may develop some small

crac

ks which are not material or structural defects.

Sticking Doors and Drawers

With the minor changes in temperature and humidity doors and drawers may swell and be

dif

ficult to open or close. Tolerances have been built into the units but extreme conditions may still

cause sticking. This will adjust back to normal over time but until it does consider using a

deh

umidifier or rub candle wax or paraffin on the sides that stick.

Avoid Direct Sunlight

Keep the furniture out of direct sunlight. Ultraviolet rays will fade colors and in some cases

darken them. It can also cause crazing or hair line cracks in the finish. White finishes will yellow

naturally over time and exposure to direct sunlight will hasten this natural process along with some

woods darkening naturally over time; this is not considered to be a quality defect.

Proper Storage

If you need to put your furniture in storage for any period of time do not store them in a damp

basement or hot dry attic. Allow air movement around the furniture and do not stack anything on it.

In General

Protect furniture surface from hot or extremely cold items.

Use coasters under hot or cold beverages

Do not use synthetic fabric under accessories or lamps

otect tops from pens, makers and crayons

Oils from potpourri and other scented items can damage the furniture finish.

Do not drag items across the surface of the furniture.

Allow the surface to breath by rotating your accessories and lamps.

Do not over polish the furniture, do it only two or three times a year. Over polishing can

distort the natural finish of the product.

Do not wax the furniture as wax build up can destroy the natural finish of the product.

When moving furniture always lift the unit. Do not push or drag it to avoid damage to legs

Keep the furniture level so doors and drawers open and close freely.

Clean with a damp, not wet, cloth. Use only a mild soap. Do not use abrasive cleaners.

BULLETIN NO. A-PAP00-00

STOP

IF YOU EXPERIENCE ANY

ISSUES WITH THIS PRODUC

BEFORE YOU

RETURN THIS TO

THE RETAILER

PLEASE FOLLOW

PROCEDURES ON THE

REVER

SE SIDE OF THIS FORM.

BULLETIN NO. A-PAP01-00

Product Assistance Procedures

You have purchased a quality piece of furniture. Our international team has

spent

many hours designing and engineering this piece and packaging to ensure you

will be satisfied with your purchase. But if for any reason you need help with your

purchase please

Procedures to follow should you have any questions:

For best and most timely service please contact us by e-mail at [email protected]

Please provide the following information in your e-mail.

1. Your N

ame__________________________________________________

2. Address_____________________________________________________

_____________________________________________________

Phone number________________________________________________

Place and date of purchase_____________________________________

_________________________________________________________

5. It

em number and description of your product. ____________________

_________________________________________________________

The

item number can be found on the back of the case or on the foot/headboard

f the crib. Please include all numbers found on that label including the PO# and

production date.

6. Short description o

f the issues and attach a photo if possible.

____________________________________________________________

meone will contact you via e-mail or phone to help you with your issues.

If you do not have internet access, please fax the above information to

609-409-5809

If you do not have internet or fax access, please call us at 888-266-2848 and be sure

to have all the above information ready to give to your Client Service Specialist.

A S S E M B L Y I N S T R U C T I O N S

PRINTED IN CHINA

LaJobi Industries. - 257 Prospect Plains Rd. Cranbury,NJ 08512-Phone: 888-266-2848

Bulletin No. A-WDT00-00

！ WARNING: FALL HAZARD

. TO PREVENT DEATH OR SERIOUS INJURY，ALWAYS KEEP

CHILD WITHIN ARM’S REACH.

. THIS PRODUCT NOT TO BE USED AS A CHANGING TABLE

UNLESS EQUIPPED WITH CHANGING PAD AS DESCRIBED

BELOW.

. READ ALL INSTRUCTIONS BEFORE USE OF THE CHANGING

TABLE OR THE CHANGING PAD.

. DO NOT USE THIS DRESSING/CHANGING TABLE OR CHANGING

PAD IF THERE ARE ANY LOOSE JOINTS,MISSING OR BROKEN

PARTS AND SHARP EDGES.PLEASE CONTACT

LAJOBI

INDUSTRIES,INC.,257 PROSPECT PLAINS ROAD,CRANBURY,

NJ 08512 FOR REPLACEMENT PART AND INSTRUCTIONAL

LITERATURE. DO NOT SUBSTITURE PARTS OF ANY KIND.

. KEEP ALL INSTRUCTIONS FOR FUTURE USE.

. USE ONLY AN APPROVED CHANGING PAD THAT MEETS

F23388-04.THE PAD WILL HAVE A LABEL THAT INDICATES THAT IT

MEETS F23388-04 AND MAY BE SOLD BY ANOTHER

MANUFACTURER.FOLLOW ALL PAD MANUFACTURER’S

INSTRUCTIONS.

. WHEN CHILD REACHES A MAXIMIUM WEIGHT OF 30 LBS,

THE DRESSING /CHANGING TABLE SHALL NO LONGER BE USED.

A S S E M B L Y I N S T R U C T I O N S (continued)

PRINTED IN CHINA

Step 1

Attach the two non-grooved rails(B)

to the top left and right positions on

one of the headboards(A) using

wood dowels & 1-3/4″ Bolts(G).

Attach the two wide grooved

rails(C) to the middle left and right

positions on one of the

headboards(A) using 1-3/4″

Bolts(G).Attach the four grooved

rails(D) to the bottom left and right

positions on one of the

headboards(A) using 1-3/4″

Bolts(G).See Figure 1.

Step 2

Lay the headboard on the floor,rails

up.Make sure that the thick shelf(E) is

inserted into the top wide grooved

rails.Slide the shelf through the grooves

and into the headboard.Repeat with the

two remaining thin shelves(F).See

Figure 2.

Figure 1

Dressing Table Assembly

Figure 2

LaJobi Industries. - 257 Prospect Plains Rd. Cranbury,NJ 08512-Phone: 888-266-2848

Model shown is example only.

Styles may vary.

Model shown is example only.

Styles may vary.

Bulletin No. A-DT00-00

A S S E M B L Y I N S T R U C T I O N S (continued)

PRINTED IN CHINA

Figure 4

LaJobi Industries. - 257 Prospect Plains Rd. Cranbury,NJ 08512-Phone: 888-266-2848

Model shown is example only.

Styles may vary.

Bulletin No. A-DT00-00

Figure 3

Step 4

Insert the casters (M) as shown in

Figure 4 .

Model shown is example only.

Styles may vary.

Step 3

Attach the other headboard(A) to the

rails using 1-3/4″ Bolts(G) and Wood

Dowels(L). See Figure 3.

A S S E M B L Y I N S T R U C T I O N S (continued)

PRINTED IN CHINA

Figure 6

LaJobi Industries. - 257 Prospect Plains Rd. Cranbury,NJ 08512-Phone: 888-266-2848

Model shown is example only.

Styles may vary.

Bulletin No. A-DT00-00

Figure 5

Step 6

Place the Foam Pad(O) onto the Thick Shelf(E)

on top of the attached strap from Step 5 ,as

shown in Figure 6 .

Model shown is example only.

Styles may vary.

WARNING: FALL HAZARD

ALWAY KEEP CHILD WITHIN AN ARMS REACH.

Step 5

Place the Restraint Harness(N) and

align the hole on the Harness Strap

end to the hole on the thick shelf

(E).Attach the Strap to the shelf by

inserting an Allen Head bolt (H)

through a washer (I),the Strap(N) and

the Shelf hole.Secure with a Nut (J)

on the underside of the shelf, as

shown in Figure 5. Repeat process to

attach the other side of the strap to the

shelf.

RESTRAINT HARNESS SYSTEM USE:

. Place the infant on the Dressing/Changing Table

Foam Pad.

. Position the Restraint Harness over the middle

of the infant’s torso and insert the buckled ends

into each other until they lock shut with a click.

. Gently pull the loose end of the strap to lightly

snug the Restraint Harness around the infant.

Graco 356-08-42 - Lauren Dressing Table Assembly Instructions Manual

Brand: Graco

Model: 356-08-42 - Lauren Dressing Table

Type: Assembly Instructions Manual

This manual is also suitable for

Download PDF

report

Graco 356-08-42 - Lauren Dressing Table Assembly Instructions Manual

This manual is also suitable for

Graco 356-08-42 - Lauren Dressing Table Assembly Instructions Manual

Other documents