Instruction Manual
Hakomatic B 70 CL (7061.30/35/36/40/42/44)
Instruction Manual
Hakomatic B 70 CL (7061.30/35/36/40/42/44)
Scrubmaster B70 CL
2
Introduction
Preface
Dear customer, It is our desire that the
good characteristics of the Hakomatic B
70 CL should justify the confidence you
demonstrated by making this purchase.
Prior to the first drive, carefully read the
chapter "Safety Information” as well, in
order to ensure you a safe working with
the machine.
Your own safety, as well as the safety of
others, depends to a great extent on
how the vehicle is moved and operated.
Therefore, carefully read and under-
stand this operation and maintenance
manual prior to the first drive.
The manual provides valuable informa-
tion about operation, service and
maintenance. The warning symbols as
used in this manual identifies items re-
levant to safety. Please observe the
safety provisions (see chapter "Safety
Information”).
Your authorised Hako dealer will be
pleased to answer further questions re-
garding the vehicle or the operation and
maintenance manual.
Please be advised explicitly that we
cannot accept any legal issues out of
the contents of this manual.
If repair work has to be performed make
sure that only genuine spare parts are
used; only genuine spare parts may
guarantee a dependable machine.
We reserve the right for technical im-
provement..
Valid as of: Oktober 2006
Hako GmbH
D-23843 Bad Oldesloe
Hamburger Str. 209-239
Telefon ++49 (04531) 8060
Proper use
The machine is a vacuum scrubbing
machine for wet cleaning of hard-sur-
faced floors. Using the machine beyond
this scope of application will be deemed
improper use; The manufacturer cannot
be held liable for consequential dama-
ges; the user alone bears the risk.
The term of proper use also includes
operation, maintenance and repair work
to be performed in compliance with the
manufacturer's specifications.
The Hakomatic B 70 CL may be used
by persons only that are familiar with
the machine and aware of possible ha-
zards
involved.
The applicable Accident Prevention Re-
gulations and further regulations in vi-
gour concerning aspects of safety and
working medicine will have to be com-
plied with.
If modifications to the machine are
made in absence of the manufacturer's
prior consent, the latter cannot be held
liable for damage resulting from such
unauthorized modification.
Introduction
2
Introduction
Preface
Dear customer, It is our desire that the
good characteristics of the Hakomatic B
70 CL should justify the confidence you
demonstrated by making this purchase.
Prior to the first drive, carefully read the
chapter "Safety Information” as well, in
order to ensure you a safe working with
the machine.
Your own safety, as well as the safety of
others, depends to a great extent on
how the vehicle is moved and operated.
Therefore, carefully read and under-
stand this operation and maintenance
manual prior to the first drive.
The manual provides valuable informa-
tion about operation, service and
maintenance. The warning symbols as
used in this manual identifies items re-
levant to safety. Please observe the
safety provisions (see chapter "Safety
Information”).
Your authorised Hako dealer will be
pleased to answer further questions re-
garding the vehicle or the operation and
maintenance manual.
Please be advised explicitly that we
cannot accept any legal issues out of
the contents of this manual.
If repair work has to be performed make
sure that only genuine spare parts are
used; only genuine spare parts may
guarantee a dependable machine.
We reserve the right for technical im-
provement..
Valid as of: Oktober 2006
Hako-Werke GmbH
D-23843 Bad Oldesloe
Hamburger Str. 209-239
Telefon ++49 (04531) 8060
Proper use
The machine is a vacuum scrubbing
machine for wet cleaning of hard-sur-
faced floors. Using the machine beyond
this scope of application will be deemed
improper use; The manufacturer cannot
be held liable for consequential dama-
ges; the user alone bears the risk.
The term of proper use also includes
operation, maintenance and repair work
to be performed in compliance with the
manufacturer's specifications.
The Hakomatic B 70 CL may be used
by persons only that are familiar with
the machine and aware of possible ha-
zards
involved.
The applicable Accident Prevention Re-
gulations and further regulations in vi-
gour concerning aspects of safety and
working medicine will have to be com-
plied with.
If modifications to the machine are
made in absence of the manufacturer's
prior consent, the latter cannot be held
liable for damage resulting from such
unauthorized modification.
Introduction
April 2014
Scrubmaster
B70 CLshould justify the confidenece you
Scrubmaster B70 CL may be used
3
Notes on warranty
The terms of the sales contract apply.
Damages are not subject to warranty if
they are due to non-compliance with the
maintenance and service provisions.
The maintenance work has to be perfor-
med by an authorized Minuteman ser-
vice center and confirmed in the
"Maintenance certificate" which is the
warranty document.
The following is excluded from
warranty: fuses, natural wear, damages
caused by overload, inexpert handling
and unauthorized modification of the
machine. Moreover, any claim for war-
ranty cannot be accepted if damages of
the machine are caused by fitting parts
or accessories without Minuteman's pri-
or and explicit consent or by non-com-
pliance with the maintenance
instructions.
Acceptance of the machine
Upon arrival, check machine for possi-
ble damages in transit. For refund of
such damage, have the Deutsche Bahn
AG or your freight forwarder confirm
such damage. Mail notification and
waybill to:
Hako GmbH
Hamburger Strasse 209-239
23843 Bad Oldesloe
Introduction
3
Notes on warranty
The terms of the sales contract apply.
Damages are not subject to warranty if
they are due to non-compliance with the
maintenance and service provisions.
The maintenance work has to be perfor-
med by an authorized Minuteman ser-
vice center and confirmed in the
"Maintenance certificate" which is the
warranty document.
The following is excluded from
warranty: fuses, natural wear, damages
caused by overload, inexpert handling
and unauthorized modification of the
machine. Moreover, any claim for war-
ranty cannot be accepted if damages of
the machine are caused by fitting parts
or accessories without Minuteman's pri-
or and explicit consent or by non-com-
pliance with the maintenance
instructions.
Acceptance of the machine
Upon arrival, check machine for possi-
ble damages in transit. For refund of
such damage, have the Deutsche Bahn
AG or your freight forwarder confirm
such damage. Mail notification and
waybill to:
Hako-Werke GmbH
Hamburger Strasse 209-239
23843 Bad Oldesloe
Introduction
4
Table of Content
Introduction . . . . . . . . . . . . . 2
Preface. . . . . . . . . . . . . . . . . . 2
Proper use . . . . . . . . . . . . . . . 2
Notes of warranty . . . . . . . . . . 3
Acceptance of the machine . . 3
1 Safety information . . . . . . . . 5
1.1 Safety and Warning Symbols. 5
1.2 General Provisions. . . . . . . . . 6
1.3 Provisions for Operation. . . . . 6
1.4 Maintenance instructions . . . . 7
1.5 Specific Hazards . . . . . . . . . . 8
1.6 Information for Protection of En-
vironment . . . . . . . . . . . . . . . . 8
1.7 Labels at the Machine . . . . . . 9
2 First Operation . . . . . . . . . . 10
2.1 Instruction. . . . . . . . . . . . . . . 10
2.2 Initial charging procedure. . . 10
2.3 Before Taking into Operation 10
2.4 Start Machine . . . . . . . . . . . . 10
2.5 Operation . . . . . . . . . . . . . . . 11
2.6 Stop Machine . . . . . . . . . . . . 11
2.7 After Work . . . . . . . . . . . . . . 11
2.8 Transport rides . . . . . . . . . . . 11
3 Operation . . . . . . . . . . . . . . 12
3.1 Method of operation . . . . . . . 12
3.1.1 Brush Head . . . . . . . . . . . . . 12
3.1.2 Clear Water Tank . . . . . . . . . 12
3.1.3 Squeegee. . . . . . . . . . . . . . . 13
3.1.4 Soiled Water Tank . . . . . . . . 13
3.1.5 Travel Drive . . . . . . . . . . . . . 13
3.1.6 Batteries and Charger . . . . . 13
3.1.7 Options. . . . . . . . . . . . . . . . . 13
3.2 Operating and Indicating Ele-
ments . . . . . . . . . . . . . . . . . . 14
3.2.1 Operating Panel . . . . . . . . . . 14
3.2.2 At the machine . . . . . . . . . . . 17
4 Technical Data . . . . . . . . . . 20
5 Maintenance and Care . . . . 22
5.1 Hako System Maintenance . 22
5.2 Maintenance document . . . . 23
5.3 Maintenance Schedule. . . . . 24
5.4 Battery Systems . . . . . . . . . . 28
5.4.1 Charge Batteries . . . . . . . . . 29
5.4.2 Low Discharge Signal sender
(LDS) . . . . . . . . . . . . . . . . . . 29
5.4.3 Maintenance of Drive
Batteries . . . . . . . . . . . . . . . . 29
5.4.4 Remove Batteries. . . . . . . . . 29
5.4.5 Install Batteries. . . . . . . . . . . 29
5.4.6 Disposal of Batteries . . . . . . 29
5.5 Clear Water Tank . . . . . . . . . 30
5.5.1 Fill Clear Water Tank . . . . . . 31
5.5.2 Empty Clear Water Tank . . . 31
5.5.3 Clean Clear Water Filter. . . . 31
5.6 Soiled Water Tank . . . . . . . . 32
5.6.1 Empty Soiled Water Tank . . 33
5.6.2 Clean Soiled Water Tank . . . 33
5.6.3 Clean Suction Filter . . . . . . . 33
5.7 Plate brush head . . . . . . . . . 34
5.7.1 Clean Brushes . . . . . . . . . . . 34
5.7.2 Change Brushes . . . . . . . . . 34
5.7.3 Change Deflector Roller. . . . 34
5.7.4 Change Sealing Strip . . . . . . 34
5.8 Roll brush head . . . . . . . . . . 35
5.8.1 Clean dirt hopper . . . . . . . . . 35
5.8.2 Remove brushes . . . . . . . . . 35
5.8.3 Clean brushes . . . . . . . . . . . 35
5.8.4 Fit brushes . . . . . . . . . . . . . . 35
5.8.5 Change deflector roller. . . . . 35
5.9 Squeegee. . . . . . . . . . . . . . . 36
5.9.1 Clean Squeegee . . . . . . . . . 36
5.9.2 Change Sealing strips . . . . . 36
5.9.3 Adjust Sealing strips. . . . . . . 36
EC-Declaration of Conformity
. . . . . . . . . . . . . . . . . . . . . . . 37
4
Table of Content
Introduction . . . . . . . . . . . . . 2
Preface. . . . . . . . . . . . . . . . . . 2
Proper use . . . . . . . . . . . . . . . 2
Notes of warranty . . . . . . . . . . 3
Acceptance of the machine . . 3
1 Safety information . . . . . . . . 5
1.1 Safety and Warning Symbols. 5
1.2 General Provisions. . . . . . . . . 6
1.3 Provisions for Operation. . . . . 6
1.4 Maintenance instructions . . . . 7
1.5 Specific Hazards . . . . . . . . . . 8
1.6 Information for Protection of En-
vironment . . . . . . . . . . . . . . . . 8
1.7 Labels at the Machine . . . . . . 9
2 First Operation . . . . . . . . . . 10
2.1 Instruction. . . . . . . . . . . . . . . 10
2.2 Initial charging procedure. . . 10
2.3 Before Taking into Operation 10
2.4 Start Machine . . . . . . . . . . . . 10
2.5 Operation . . . . . . . . . . . . . . . 11
2.6 Stop Machine . . . . . . . . . . . . 11
2.7 After Work . . . . . . . . . . . . . . 11
2.8 Transport rides . . . . . . . . . . . 11
3 Operation . . . . . . . . . . . . . . 12
3.1 Method of operation . . . . . . . 12
3.1.1 Brush Head . . . . . . . . . . . . . 12
3.1.2 Clear Water Tank . . . . . . . . . 12
3.1.3 Squeegee. . . . . . . . . . . . . . . 13
3.1.4 Soiled Water Tank . . . . . . . . 13
3.1.5 Travel Drive . . . . . . . . . . . . . 13
3.1.6 Batteries and Charger . . . . . 13
3.1.7 Options. . . . . . . . . . . . . . . . . 13
3.2 Operating and Indicating Ele-
ments . . . . . . . . . . . . . . . . . . 14
3.2.1 Operating Panel . . . . . . . . . . 14
3.2.2 At the machine . . . . . . . . . . . 17
4 Technical Data . . . . . . . . . . 20
5 Maintenance and Care . . . . 22
5.1 Hako System Maintenance . 22
5.2 Maintenance document . . . . 23
5.3 Maintenance Schedule. . . . . 24
5.4 Battery Systems . . . . . . . . . . 28
5.4.1 Charge Batteries . . . . . . . . . 29
5.4.2 Low Discharge Signal sender
(LDS) . . . . . . . . . . . . . . . . . . 29
5.4.3 Maintenance of Drive
Batteries . . . . . . . . . . . . . . . . 29
5.4.4 Remove Batteries. . . . . . . . . 29
5.4.5 Install Batteries. . . . . . . . . . . 29
5.4.6 Disposal of Batteries . . . . . . 29
5.5 Clear Water Tank . . . . . . . . . 30
5.5.1 Fill Clear Water Tank . . . . . . 31
5.5.2 Empty Clear Water Tank . . . 31
5.5.3 Clean Clear Water Filter. . . . 31
5.6 Soiled Water Tank . . . . . . . . 32
5.6.1 Empty Soiled Water Tank . . 33
5.6.2 Clean Soiled Water Tank . . . 33
5.6.3 Clean Suction Filter . . . . . . . 33
5.7 Plate brush head . . . . . . . . . 34
5.7.1 Clean Brushes . . . . . . . . . . . 34
5.7.2 Change Brushes . . . . . . . . . 34
5.7.3 Change Deflector Roller. . . . 34
5.7.4 Change Sealing Strip . . . . . . 34
5.8 Roll brush head . . . . . . . . . . 35
5.8.1 Clean dirt hopper . . . . . . . . . 35
5.8.2 Remove brushes . . . . . . . . . 35
5.8.3 Clean brushes . . . . . . . . . . . 35
5.8.4 Fit brushes . . . . . . . . . . . . . . 35
5.8.5 Change deflector roller. . . . . 35
5.9 Squeegee. . . . . . . . . . . . . . . 36
5.9.1 Clean Squeegee . . . . . . . . . 36
5.9.2 Change Sealing strips . . . . . 36
5.9.3 Adjust Sealing strips. . . . . . . 36
EC-Declaration of Conformity
. . . . . . . . . . . . . . . . . . . . . . . 37
5
Safety information
1 Safety information
1.1 Safety and Warning Symbols
All paragraphs in this manual referring
to your personal safety, the safety of
your machine and the environment pro-
tection are attributed one of the follo-
wing warning symbols:
Symbol Hazardous for ... Description
Safety Provisions persons and goods Safety Provisions in dangerous situation caused by
misuse inaccurate adherence of instructions or pres-
cribed work routine.
CAUTION the machine important information on handling the machine in
order to maintain operability.
Ecological hazard the environment due to use of substances representing an inherent
danger to health of environment
5
Safety information
1 Safety information
1.1 Safety and Warning Symbols
All paragraphs in this manual referring
to your personal safety, the safety of
your machine and the environment pro-
tection are attributed one of the follo-
wing warning symbols:
Symbol Hazardous for ... Description
Safety Provisions persons and goods Safety Provisions in dangerous situation caused by
misuse inaccurate adherence of instructions or pres-
cribed work routine.
CAUTION the machine important information on handling the machine in
order to maintain operability.
Ecological hazard the environment due to use of substances representing an inherent
danger to health of environment
6
Safety information
1.2 General Provisions
• Apart from the provisions contained
in this instruction manual, the gene-
ral safety provisions and the acci-
dent prevention regulations as
imposed by law have to be complied
with.
• Before taking your machine into ope-
ration, carefully read the instruction
manual as well as other separate in-
structions for accessories or atta-
ched implements and comply with all
points mentioned there during work.
• Persons being trained by qualified
Hako technicians only are authori-
sed to operate, service and repair
the machine.
• You are advised to thoroughly study
the safety instructions since precise
knowledge only helps avoiding er-
rors during operation of the machine
and thus guarantee faultless usage
of the machine.
• The operating instructions have to
be at hand at the place of use of the
machine, and therefore have to be
kept readily available at the machi-
ne.
• When selling or letting the machine
for rent, hand out these documents
to the new owner/operator and have
the transfer certified!
• The warning and instruction plates
attached to the machine contain va-
luable advice about safe operation.
Immediately replace incomplete or il-
legible labels.
• As far as safety standards are con-
cerned, spare have to equal genuine
spare parts!
1.3 Provisions for Operation
• Before first operation of the machine,
fully charge the battery with an initial
charging procedure and comply with
the operating instructions of the
charger as well as with those of the
battery manufacturer. Hako cannot
be held liable for damages resulting
from the fact that the initial charging
has not or insufficiently been done.
• Before taking into operation, check
the machine for operational safety!
Immediately remedy malfunctions!
• It is indispensable for the operator to
get acquainted with all attached im-
plements and controls as well as
with their function before operation
begins. Once you have started to
work, no time will be left to do so!
• When working with the machine use
firm and skid proof shoes.
• The machine may be used only on
such surfaces clearly specified by
the owner or his authorised repre-
sentative.
• When working with the machine take
notice of third persons, especially
children.
• Start riding immediately after brush
head has lowered otherwise the
brush might leave traces on the
ground. Lift the brush head before ri-
ding over obstacles (doorsteps).
• Only fold open empty soiled water
tank
• Use only cleaning agents suitable for
automatic machines (low-foaming)
and comply with the instructions for
use, disposal and with the warning
information specified by the cleaning
agent's manufacturer.
• The machine is not designed for col-
lecting hazardous, inflammable or
explosive dusts or substances.
• Usage of the machine in explosive
areas is prohibited.
• Pull the switching key to avoid un-
authorized use of the machine.
• Before transport of the machine, lift
6
Safety information
1.2 General Provisions
• Apart from the provisions contained
in this instruction manual, the gene-
ral safety provisions and the acci-
dent prevention regulations as
imposed by law have to be complied
with.
• Before taking your machine into ope-
ration, carefully read the instruction
manual as well as other separate in-
structions for accessories or atta-
ched implements and comply with all
points mentioned there during work.
• Persons being trained by qualified
Hako technicians only are authori-
sed to operate, service and repair
the machine.
• You are advised to thoroughly study
the safety instructions since precise
knowledge only helps avoiding er-
rors during operation of the machine
and thus guarantee faultless usage
of the machine.
• The operating instructions have to
be at hand at the place of use of the
machine, and therefore have to be
kept readily available at the machi-
ne.
• When selling or letting the machine
for rent, hand out these documents
to the new owner/operator and have
the transfer certified!
• The warning and instruction plates
attached to the machine contain va-
luable advice about safe operation.
Immediately replace incomplete or il-
legible labels.
• As far as safety standards are con-
cerned, spare have to equal genuine
spare parts!
1.3 Provisions for Operation
• Before first operation of the machine,
fully charge the battery with an initial
charging procedure and comply with
the operating instructions of the
charger as well as with those of the
battery manufacturer. Hako cannot
be held liable for damages resulting
from the fact that the initial charging
has not or insufficiently been done.
• Before taking into operation, check
the machine for operational safety!
Immediately remedy malfunctions!
• It is indispensable for the operator to
get acquainted with all attached im-
plements and controls as well as
with their function before operation
begins. Once you have started to
work, no time will be left to do so!
• When working with the machine use
firm and skid proof shoes.
• The machine may be used only on
such surfaces clearly specified by
the owner or his authorised repre-
sentative.
• When working with the machine take
notice of third persons, especially
children.
• Start riding immediately after brush
head has lowered otherwise the
brush might leave traces on the
ground. Lift the brush head before ri-
ding over obstacles (doorsteps).
• Only fold open empty soiled water
tank
• Use only cleaning agents suitable for
automatic machines (low-foaming)
and comply with the instructions for
use, disposal and with the warning
information specified by the cleaning
agent's manufacturer.
• The machine is not designed for col-
lecting hazardous, inflammable or
explosive dusts or substances.
• Usage of the machine in explosive
areas is prohibited.
• Pull the switching key to avoid un-
authorized use of the machine.
• Before transport of the machine, lift
7
Safety information
the squeegee and the brush head.
Adapt driving habit to local conditi-
ons.
• The machine may be used only for
operation on plane areas with a ma-
ximum inclination of up to 2 %.
1.4 Maintenance instructions
• The daily and weekly maintenance
and repair task must be performed
by a qualified operator. For any
maintenance and repair work
beyond please contact your local
Hako service centre.
• Observe the maintenance activities
and intervals set out in the instruc-
tion manual.
• Maintenance and repair work may
be carried out only by means of ap-
propriate tools.
• Have the machine checked for safe
condition in the sense of the Acci-
dent Prevention Regulation by an
expert at regular intervals (recom-
mendation: at least once yearly) as
well as after modifications or repair.
• Spare parts have to equal the techni-
cal requirements as specified by the
manufacturer! Genuine spare parts
guarantee compliance with these re-
quirements.
• Stop engine before proceeding to in-
spection and maintenance work.
• To prevent the machine from being
used by unauthorized persons, the
control key must be removed.
• When performing work at the electri-
cal system, be sure to remove the
battery plug.
• Make sure to protect the soiled water
tank against accidental closing or til-
ting down before working in the area
of a lifted tank lid.
• Do not clean the electrical parts by
means of high-pressure cleaning
equipment.
• The use of aggressive detergents is
not admitted.
• Let the machine dry after cleaning
e.g. for weekend.
• The machine may be taken into ope-
ration after all protective devices
have been fitted and positioned.
1.5 Specific Hazards
Electric system
• Only use genuine fuses with prescri-
bed connecting load.
• In case of malfunction of the electric
system, immediately shutdown ma-
chine and remedy.
• Qualified personnel only is authori-
sed to proceed to works at the elec-
trical equipment and only according
to electro-technical rules.
• Inspect/check the electrical equip-
ment of the machine at regular inter-
valls. Immediately remedy defects
such e.g. loose connections or scor-
ched cables.
Battery
• Respect the operating instructions of
the battery manufacturer.
• Handling and changes of the batte-
ries may take place only by mainte-
nance staff.
• Never place metal objects or tools on
batteries - short-circuit hazard!
• Due to alteration of the centre of gra-
vity, only use batteries as released
and at the prescribed position only.
• Provide for sufficient ventilation of
areas where batteries are charged. –
Explosion hazard!
• Refer to safety provisions in supple-
ment 88-60-2556 - Information on
drive batteries.
7
Safety information
the squeegee and the brush head.
Adapt driving habit to local conditi-
ons.
• The machine may be used only for
operation on plane areas with a ma-
ximum inclination of up to 2 %.
1.4 Maintenance instructions
• The daily and weekly maintenance
and repair task must be performed
by a qualified operator. For any
maintenance and repair work
beyond please contact your local
Hako service centre.
• Observe the maintenance activities
and intervals set out in the instruc-
tion manual.
• Maintenance and repair work may
be carried out only by means of ap-
propriate tools.
• Have the machine checked for safe
condition in the sense of the Acci-
dent Prevention Regulation by an
expert at regular intervals (recom-
mendation: at least once yearly) as
well as after modifications or repair.
• Spare parts have to equal the techni-
cal requirements as specified by the
manufacturer! Genuine spare parts
guarantee compliance with these re-
quirements.
• Stop engine before proceeding to in-
spection and maintenance work.
• To prevent the machine from being
used by unauthorized persons, the
control key must be removed.
• When performing work at the electri-
cal system, be sure to remove the
battery plug.
• Make sure to protect the soiled water
tank against accidental closing or til-
ting down before working in the area
of a lifted tank lid.
• Do not clean the electrical parts by
means of high-pressure cleaning
equipment.
• The use of aggressive detergents is
not admitted.
• Let the machine dry after cleaning
e.g. for weekend.
• The machine may be taken into ope-
ration after all protective devices
have been fitted and positioned.
1.5 Specific Hazards
Electric system
• Only use genuine fuses with prescri-
bed connecting load.
• In case of malfunction of the electric
system, immediately shutdown ma-
chine and remedy.
• Qualified personnel only is authori-
sed to proceed to works at the elec-
trical equipment and only according
to electro-technical rules.
• Inspect/check the electrical equip-
ment of the machine at regular inter-
valls. Immediately remedy defects
such e.g. loose connections or scor-
ched cables.
Battery
• Respect the operating instructions of
the battery manufacturer.
• Handling and changes of the batte-
ries may take place only by mainte-
nance staff.
• Never place metal objects or tools on
batteries - short-circuit hazard!
• Due to alteration of the centre of gra-
vity, only use batteries as released
and at the prescribed position only.
• Provide for sufficient ventilation of
areas where batteries are charged. –
Explosion hazard!
• Refer to safety provisions in supple-
ment 88-60-2556 - Information on
drive batteries.
8
Safety information
1.6 Information for Protection of
Environment
• For safe use of substances inheriting
a danger to health and environment
specific knowledge is required.
• Observe the legal directives and lo-
cal regulations for disposal of deter-
gents, see Water Management Act.
• Used batteries labelled as recyclable
contain reusable economic goods.
According to the crossed dustbin la-
bel these batteries must not be ad-
ded to the normal waste. Provide for
agreement with the Hako contract
dealer on return and disposal accor-
ding to § 8 BattV.
8
Safety information
1.6 Information for Protection of
Environment
• For safe use of substances inheriting
a danger to health and environment
specific knowledge is required.
• Observe the legal directives and lo-
cal regulations for disposal of deter-
gents, see Water Management Act.
• Used batteries labelled as recyclable
contain reusable economic goods.
According to the crossed dustbin la-
bel these batteries must not be ad-
ded to the normal waste. Provide for
agreement with the Hako contract
dealer on return and disposal accor-
ding to § 8 BattV.
9
Safety information
1.7 Labels at the Machine
The following safety and information la-
bels are legibly attached to the machi-
ne. Replace missing or illegible labels
immediately.
Hako nameplate (Fig. 1/1)
Machine identification number (Fig. 1/2)
Soiled water drain hose (Fig. 1/3)
A = Read and observe the instruction
manual (Fig. 1/2)
B = Maximum inclination of 10%
(Fig. 1/2)
C = Do not clean the machine by means
of high-pressure cleaning equipment
(Fig. 1/2)
Fig.1
USA
A
B
C
10
1
2
3
9
Safety information
1.7 Labels at the Machine
The following safety and information la-
bels are legibly attached to the machi-
ne. Replace missing or illegible labels
immediately.
Hako nameplate (Fig. 1/1)
Machine identification number (Fig. 1/2)
Soiled water drain hose (Fig. 1/3)
A = Read and observe the instruction
manual (Fig. 1/2)
B = Maximum inclination of 10%
(Fig. 1/2)
C = Do not clean the machine by means
of high-pressure cleaning equipment
(Fig. 1/2)
Fig.1
USA
A
B
C
10
1
2
3
10
First Operation
2 First Operation
2.1 Instruction
Instruction is required before first ope-
ration. First instruction into handling of
the machine must be held by a qualified
person sent by your local Hako contract
dealer. Your Hako dealer will be infor-
med by the manufacturer upon delivery
of the vehicle and will contact you to
make a date for instruction.
2.2 Initial charging procedure
Before first operation of the
machine, fully charge the bat-
tery with an initial charging pro-
cedure and comply with the
operating instructions of the
charger as well as with those of
the battery manufacturer.
Hako cannot be held liable for
damages resulting from the
fact that the initial charging has
not or insufficiently been done.
2.3 Before Taking into Operation
Proceed to the following inspections be-
fore taking the machine into operation:
1. Check parking site for signs of leaka-
ge. Hoses, lines and tanks must be
free from any leakage or damage.
2. Install brushes and squeegee, see
maintenance chapter.
3. Install batteries and connect battery
plug, see maintenance chapter.
4. Check battery charge and proceed
to re-charging of batteries if required.
Generally proceed to initial charging
before first operation of the machine.
5. Empty soiled water tank and clean it
if required, see maintenance chap-
ter.
6. Re-fill clear water tank and add cle-
aning agent according to the manu-
facturer's recommendations.
Use only cleaning agents sui-
table for automatic machines
(low-foaming) and comply with
the instructions for use, dispo-
sal and with the warning infor-
mation specified by the cle-
aning agent's manufacturer.
2.4 Start Machine
Before start of the machine, set
accelerator level to neutral po-
sition. Should the accelerator
lever be out of neutral position
and machine be switched on,
an error message occurs.
Proceed to the following to set the ma-
chine into operating mode:
• Disconnect mains plug of the char-
ger from outlet and fasten to holder if
require.
• Switch on machine by actuation of
key switch from position (0) to positi-
on (1).
10
First Operation
2 First Operation
2.1 Instruction
Instruction is required before first ope-
ration. First instruction into handling of
the machine must be held by a qualified
person sent by your local Hako contract
dealer. Your Hako dealer will be infor-
med by the manufacturer upon delivery
of the vehicle and will contact you to
make a date for instruction.
2.2 Initial charging procedure
Before first operation of the
machine, fully charge the bat-
tery with an initial charging pro-
cedure and comply with the
operating instructions of the
charger as well as with those of
the battery manufacturer.
Hako cannot be held liable for
damages resulting from the
fact that the initial charging has
not or insufficiently been done.
2.3 Before Taking into Operation
Proceed to the following inspections be-
fore taking the machine into operation:
1. Check parking site for signs of leaka-
ge. Hoses, lines and tanks must be
free from any leakage or damage.
2. Install brushes and squeegee, see
maintenance chapter.
3. Install batteries and connect battery
plug, see maintenance chapter.
4. Check battery charge and proceed
to re-charging of batteries if required.
Generally proceed to initial charging
before first operation of the machine.
5. Empty soiled water tank and clean it
if required, see maintenance chap-
ter.
6. Re-fill clear water tank and add cle-
aning agent according to the manu-
facturer's recommendations.
Use only cleaning agents sui-
table for automatic machines
(low-foaming) and comply with
the instructions for use, dispo-
sal and with the warning infor-
mation specified by the cle-
aning agent's manufacturer.
2.4 Start Machine
Before start of the machine, set
accelerator level to neutral po-
sition. Should the accelerator
lever be out of neutral position
and machine be switched on,
an error message occurs.
Proceed to the following to set the ma-
chine into operating mode:
• Disconnect mains plug of the char-
ger from outlet and fasten to holder if
require.
• Switch on machine by actuation of
key switch from position (0) to positi-
on (1).
11
First Operation
2.5 Operation
1. Switch on the machine.
2. Use lever (Fig. 5/3) to lower squee-
gee. Suction turbine switches on au-
tomatically.
3. Switch on clear water supply by me-
ans of tip-switch (Fig. 4/14).
4. Adjust clear water amount by means
of tip-switch (Fig. 4/13).
5. Use pedal (Fig. 5/9) to lower brush
head.
6. Use accelerator lever (Fig. 5/1) to
adjust work speed and direction.
Increases the plate brush pressure if
required with pedal (Fig. 5/10) .
Start moving machine imme-
diately after lowering of the
brush head, otherwise the
brushes leave traces on the
floor. Lift-out squeegee before
changing to reverse ride and
lift-out brush head before pas-
sing over dormers and more.
2.6 Stop Machine
If release the accelerator lever, this re-
turns automatically into the neutral posi-
tion. The machine stops. Protect the
machine against unintentional move-
ments or against being inadvertently
started.
2.7 After Work
1. Ride machine to suitable site for
maintenance.
2. Stop machine, lift squeegee and
brush head and pull key switch.
3. Empty and clean soiled water tank.
Observe the legal directives
and local regulations for dispo-
sal of detergents, see Water
Management Act.
4. Check clear water filter.
5. Check seals and suction hose.
6. Check operating media levels,
function and setting.
7. Charge batteries.
8. Clean the machine.
Empty the clear water tank before
shutting down the machine for a longer
time.
Do not clean the electrical
parts by means of high-pressu-
re cleaning equipment.
2.8 Transport rides
For transport rides to the place of use of
the machine, switch it on, lift-out squee-
gee and brush head and actuate the ac-
celerator switch according to the
desired direction of travel.
2.9 Tie-down points
In case of transport on a vehicle or trai-
ler, the machine has to be protected
against rolling off. Tie the machine
down firmly by lashing it to the front with
the eye bolts (Fig. 2/1) and to the rear
with the chassis (Fig. 2/2) .
Fig.2
12
11
First Operation
2.5 Operation
1. Switch on the machine.
2. Use lever (Fig. 5/3) to lower squee-
gee. Suction turbine switches on au-
tomatically.
3. Switch on clear water supply by me-
ans of tip-switch (Fig. 4/14).
4. Adjust clear water amount by means
of tip-switch (Fig. 4/13).
5. Use pedal (Fig. 5/9) to lower brush
head.
6. Use accelerator lever (Fig. 5/1) to
adjust work speed and direction.
Increases the plate brush pressure if
required with pedal (Fig. 5/10) .
Start moving machine imme-
diately after lowering of the
brush head, otherwise the
brushes leave traces on the
floor. Lift-out squeegee before
changing to reverse ride and
lift-out brush head before pas-
sing over dormers and more.
2.6 Stop Machine
If release the accelerator lever, this re-
turns automatically into the neutral posi-
tion. The machine stops. Protect the
machine against unintentional move-
ments or against being inadvertently
started.
2.7 After Work
1. Ride machine to suitable site for
maintenance.
2. Stop machine, lift squeegee and
brush head and pull key switch.
3. Empty and clean soiled water tank.
Observe the legal directives
and local regulations for dispo-
sal of detergents, see Water
Management Act.
4. Check clear water filter.
5. Check seals and suction hose.
6. Check operating media levels,
function and setting.
7. Charge batteries.
8. Clean the machine.
Empty the clear water tank before
shutting down the machine for a longer
time.
Do not clean the electrical
parts by means of high-pressu-
re cleaning equipment.
2.8 Transport rides
For transport rides to the place of use of
the machine, switch it on, lift-out squee-
gee and brush head and actuate the ac-
celerator switch according to the
desired direction of travel.
2.9 Tie-down points
In case of transport on a vehicle or trai-
ler, the machine has to be protected
against rolling off. Tie the machine
down firmly by lashing it to the front with
the eye bolts (Fig. 2/1) and to the rear
with the chassis (Fig. 2/2) .
Fig.2
12
12
Operation
3 Operation
3.1 Method of operation
General
The Hakomatic B 70 CL is a vacuum
srubbing machine for wet cleaning of
hard-surfaced floors.
3.1.1 Brush Head
Lower brush head (Fig. 3/1) via pedal
before scrubbing. The brushes rotate
and water supply switches on automati-
cally. With the accelerator lever in neu-
tral position (machines stopped)
brushes and water supply switch off au-
tomatically. The figures represent plate
brush head type machines. Equipment
of the machine with cylindrical broom
head is also available.
3.1.2 Clear Water Tank
Fill the clear water tank (Fig. 3/2) after
folding up the opening. The clear water
tank holds 70 litres and the filling level
can be followed optically (through trans-
parent hose). Regulation of water
amount is available via adjustment
handle. Adjust water amount by means
of tip-switch.
Fig.3
2
3
4
1
6
7
5
12
Operation
3 Operation
3.1 Method of operation
General
The Hakomatic B 70 CL is a vacuum
srubbing machine for wet cleaning of
hard-surfaced floors.
3.1.1 Brush Head
Lower brush head (Fig. 3/1) via pedal
before scrubbing. The brushes rotate
and water supply switches on automati-
cally. With the accelerator lever in neu-
tral position (machines stopped)
brushes and water supply switch off au-
tomatically. The figures represent plate
brush head type machines. Equipment
of the machine with cylindrical broom
head is also available.
3.1.2 Clear Water Tank
Fill the clear water tank (Fig. 3/2) after
folding up the opening. The clear water
tank holds 70 litres and the filling level
can be followed optically (through trans-
parent hose). Regulation of water
amount is available via adjustment
handle. Adjust water amount by means
of tip-switch.
Fig.3
2
3
4
1
6
7
5
Scrubmaster B70 CL is a vacuum
13
Operation
3.1.3 Squeegee
The movable squeegee (Fig. 3/3) con-
sists of the squeegee lift-out, the suc-
tion turbine and sealing strips. The
soiled water is wiped from the floor by
means of sealing strips. Squeegee is lo-
wered via hand lever. Simultaneously,
the suction turbine switches on. The
suction turbine works independent of di-
rection of travel and even if the machine
stops. Second actuation of the hand le-
ver lifts the squeegee up again and suc-
tion turbine is automatically switched off
with a delay of 15 seconds.
3.1.4 Soiled Water Tank
The soiled water is taken from squee-
gee to the soiled water tank (Fig. 3/4) by
suction turbine and suction hose. For
cleaning and collecting water at places
where access is difficult, the machine is
equipped with handheld suction hose.
3.1.5 Travel Drive
The machine features a continuous tra-
vel drive (Fig. 3/5). The electronic travel
drive control realises modification of tra-
vel speed, direction as well as dynamic
braking.
3.1.6 Batteries and Charger
The machine is equipped with mainte-
nance-free 180 Ah batteries (Fig. 3/6), ,
an automatic charger unit (Fig. 3/7) and
a low discharge signal sender (LDS) for
protection against low discharge.
Information on drive batteries, see leaf-
let 88-60-2556.
3.1.7 Options
• Dosage system and floater unit for
automatic filling
• Extraction hose including suction
pipe, joint nozzle and wet suction
nozzle
• Mop holder and tool-box for cleaning
utensils
• Silence Kit for soundproofed operati-
on
• Privat-Label for additional labels.
• Scrubbing tool
Accessories such as brushes,
rollers, pads, pad holder with
centerlock and sealing strips
you find in our spare parts ca-
talogue in the Internet under
www.hako.com
13
Operation
3.1.3 Squeegee
The movable squeegee (Fig. 3/3) con-
sists of the squeegee lift-out, the suc-
tion turbine and sealing strips. The
soiled water is wiped from the floor by
means of sealing strips. Squeegee is lo-
wered via hand lever. Simultaneously,
the suction turbine switches on. The
suction turbine works independent of di-
rection of travel and even if the machine
stops. Second actuation of the hand le-
ver lifts the squeegee up again and suc-
tion turbine is automatically switched off
with a delay of 15 seconds.
3.1.4 Soiled Water Tank
The soiled water is taken from squee-
gee to the soiled water tank (Fig. 3/4) by
suction turbine and suction hose. For
cleaning and collecting water at places
where access is difficult, the machine is
equipped with handheld suction hose.
3.1.5 Travel Drive
The machine features a continuous tra-
vel drive (Fig. 3/5). The electronic travel
drive control realises modification of tra-
vel speed, direction as well as dynamic
braking.
3.1.6 Batteries and Charger
The machine is equipped with mainte-
nance-free 180 Ah batteries (Fig. 3/6), ,
an automatic charger unit (Fig. 3/7) and
a low discharge signal sender (LDS) for
protection against low discharge.
Information on drive batteries, see leaf-
let 88-60-2556.
3.1.7 Options
• Dosage system and floater unit for
automatic filling
• Extraction hose including suction
pipe, joint nozzle and wet suction
nozzle
• Mop holder and tool-box for cleaning
utensils
• Silence Kit for soundproofed operati-
on
• Privat-Label for additional labels.
• Scrubbing tool
Accessories such as brushes,
rollers, pads, pad holder with
centerlock and sealing strips
you find in our spare parts ca-
talogue in the Internet under
www.hako.com
14
Operation
3.2 Operating and Indicating Ele-
ments
3.2.1 Operating Panel
1Display
2 Key switch
3 Battery charge indication
4 LDS indicator
5 Symbol brush drive
6 Symbol suction turbine drive
7 Hourmeter
8 Symbol Service indicator
9free
10 Symbol Silence Kit (optional)
11 Symbol clear water dosage
12 Tip-switch Silence Kit (optional)
13 Tip-switch clear water dosage
14 Tip-switch clear water supply On/Off
15 Symbol vacuum scrubbing tool
(optional)
Fig.4
17 9 843
12
6
13
10
14
5
2
11
15
14
Operation
3.2 Operating and Indicating Ele-
ments
3.2.1 Operating Panel
1Display
2 Key switch
3 Battery charge indication
4 LDS indicator
5 Symbol brush drive
6 Symbol suction turbine drive
7 Hourmeter
8 Symbol Service indicator
9free
10 Symbol Silence Kit (optional)
11 Symbol clear water dosage
12 Tip-switch Silence Kit (optional)
13 Tip-switch clear water dosage
14 Tip-switch clear water supply On/Off
15 Symbol vacuum scrubbing tool
(optional)
Fig.4
17 9 843
12
6
13
10
14
5
2
11
15
15
Operation
Display (Fig. 4/1)
This panel allows centralized monito-
ring of functions and detection of all
available operating modes.
The key switch turns the electrical sy-
stem on and off.
Pull the switching key to avoid
unauthorized use of the machi-
ne.
Battery charge indication (Fig. 4/3)
Battery charge indication appears on
the panel during the charging procedu-
re and shows the current charge condi-
tion of batteries during the procedure.
The following symbols appear:
Battery symbol A < charge of 20 %
Battery symbol B = charge of 80 %
Battery symbol C = charge of 100 %
Battery symbol D (flashes) = error
LDS indicator (Fig. 4/4)
Upon switching on, the LDS indication
is output on the panel to show the cur-
rent battery charge condition during
operation. Additional Information see
chapter maintenance.
Symbol brush drive (Fig. 4/5)
This symbol appears when brush drive
is switched on.
Symbol suction turbine drive (Fig. 4/
6)
This symbol appears when suction tur-
bine drive is switched on.
Hourmeter (Fig. 4/7)
Upon switching on, the hourmeter
briefly displays the software version
and the last error code. Then the cur-
rent operating hour level is shown.
Service indicator (Fig. 4/8)
The service indicator lights after occur-
rence of a system error and cleaning or
riding procedure is interrupted. In addi-
tion to the service indicator, a 4-digit
code is displayed on the hourmeter.
A B C D
1.1.1.1
15
Operation
Display (Fig. 4/1)
This panel allows centralized monito-
ring of functions and detection of all
available operating modes.
The key switch turns the electrical sy-
stem on and off.
Pull the switching key to avoid
unauthorized use of the machi-
ne.
Battery charge indication (Fig. 4/3)
Battery charge indication appears on
the panel during the charging procedu-
re and shows the current charge condi-
tion of batteries during the procedure.
The following symbols appear:
Battery symbol A < charge of 20 %
Battery symbol B = charge of 80 %
Battery symbol C = charge of 100 %
Battery symbol D (flashes) = error
LDS indicator (Fig. 4/4)
Upon switching on, the LDS indication
is output on the panel to show the cur-
rent battery charge condition during
operation. Additional Information see
chapter maintenance.
Symbol brush drive (Fig. 4/5)
This symbol appears when brush drive
is switched on.
Symbol suction turbine drive (Fig. 4/
6)
This symbol appears when suction tur-
bine drive is switched on.
Hourmeter (Fig. 4/7)
Upon switching on, the hourmeter
briefly displays the software version
and the last error code. Then the cur-
rent operating hour level is shown.
Service indicator (Fig. 4/8)
The service indicator lights after occur-
rence of a system error and cleaning or
riding procedure is interrupted. In addi-
tion to the service indicator, a 4-digit
code is displayed on the hourmeter.
A B C D
1.1.1.1
16
Operation
free (Fig. 4/9)
Silence Kit tip symbol (optional)
(Fig. 4/10)
This symbol appears when Silence Kit
tip-switch is switched on.
Clear water dosage symbol (Fig. 4/
11)
This symbol appears upon actuation of
the clear water dosage tip-switch.
Silence Kit tip-switch (optional) (Fig.
4/12)
This tip-switch is used to change suc-
tion turbine to silent mode. The silent
mode symbol appears in the display.
Clear water dosage tip-switch (Fig.
4/13)
This tip-switch is used to regulate the
amount of clear water. Additionally,
clear water amount is adapted to driving
speed. The display shows a six-stage
symbol for the supplied amount of clear
water.
Clear water supply ON/OFF tip-
switch (Fig. 4/14)
This tip-switch is used to switch clear
water supply ON or OFF.
Scrubbing tool symbol (optional)
(Fig. 4/15)
This symbol appears when scrubbing
tool-switch (A) is switched on
Hand cleaning tool (optional)
Hand-cleaning tool with spray function
for the Hakomatic with scrubbing tool
connection for thorough cleaning on
areas which are difficult to reach.
A
16
Operation
free (Fig. 4/9)
Silence Kit tip symbol (optional)
(Fig. 4/10)
This symbol appears when Silence Kit
tip-switch is switched on.
Clear water dosage symbol (Fig. 4/
11)
This symbol appears upon actuation of
the clear water dosage tip-switch.
Silence Kit tip-switch (optional) (Fig.
4/12)
This tip-switch is used to change suc-
tion turbine to silent mode. The silent
mode symbol appears in the display.
Clear water dosage tip-switch (Fig.
4/13)
This tip-switch is used to regulate the
amount of clear water. Additionally,
clear water amount is adapted to driving
speed. The display shows a six-stage
symbol for the supplied amount of clear
water.
Clear water supply ON/OFF tip-
switch (Fig. 4/14)
This tip-switch is used to switch clear
water supply ON or OFF.
Scrubbing tool symbol (optional)
(Fig. 4/15)
This symbol appears when scrubbing
tool-switch (A) is switched on
Hand cleaning tool (optional)
Hand-cleaning tool with spray function
for the Hakomatic with scrubbing tool
connection for thorough cleaning on
areas which are difficult to reach.
A
Scrubmaster with scrubbing tool
17
Operation
3.2.2 At the machine
1 Accelerator lever
2 Opening of clear water tank
3 Hand lever for squeegee lift-out
4 Clear water filter
5 Soiled water drain hose
6 Clear water level indication
7 Brush ejector
8 Power connection charger unit
9 Pedal brush head
10 Pedal plate brush head pressure
Fig.5
123
5
7
86
4
10
9
17
Operation
3.2.2 At the machine
1 Accelerator lever
2 Opening of clear water tank
3 Hand lever for squeegee lift-out
4 Clear water filter
5 Soiled water drain hose
6 Clear water level indication
7 Brush ejector
8 Power connection charger unit
9 Pedal brush head
10 Pedal plate brush head pressure
Fig.5
123
5
7
86
4
10
9
18
Operation
Accelerator lever (Fig. 5/1)
With the machine being switched on,
the accelerator lever allows continuous
regulation of speed. If pulled to maxi-
mum position, maximum speed is attai-
ned. Reduce speed by taking the lever
slowly back. If released, the lever auto-
matically returns into neutral position
and the machine stops (deadman
function). The parking brake of the tra-
vel drive is activated. The symbol of the
parking brake appears in the display.
Protect the machine against
rolling off before leaving it un-
attended. Before switching the
machine on again, make sure
that the accelerator lever is in
neutral position.
Opening of clear water tank (Fig. 5/2)
The clear water tank is filled after fol-
ding up the opening.
Hand lever for squeegee lift-out (Fig.
5/3)
Use this hand lever to lift and lower the
squeegee.
Clear water filter (Fig. 5/4)
While clear water flows from tank to
brush head, it is cleaned by the filter ele-
ment.
Soiled water drain hose (Fig. 5/5)
This hose allows draining the collected
soiled water from the tank.
Clear water drain hose (Fig. 5/6)
This hose allows draining the clear wa-
ter tank.
Brush ejector (Fig. 5/7)
The brush ejector makes brush removal
fast and easy.
Power connection charger unit (Fig.
5/8)
The power connection supplies the
charger unit with power.
Pedal brush head (Fig. 5/9)
Use this pedal to lift and lower the brush
head.
Pedal plate brush head pressure
(Fig. 5/10)
This pedal allows increasing the ground
pressure of the plate brush head.
18
Operation
Accelerator lever (Fig. 5/1)
With the machine being switched on,
the accelerator lever allows continuous
regulation of speed. If pulled to maxi-
mum position, maximum speed is attai-
ned. Reduce speed by taking the lever
slowly back. If released, the lever auto-
matically returns into neutral position
and the machine stops (deadman
function). The parking brake of the tra-
vel drive is activated. The symbol of the
parking brake appears in the display.
Protect the machine against
rolling off before leaving it un-
attended. Before switching the
machine on again, make sure
that the accelerator lever is in
neutral position.
Opening of clear water tank (Fig. 5/2)
The clear water tank is filled after fol-
ding up the opening.
Hand lever for squeegee lift-out (Fig.
5/3)
Use this hand lever to lift and lower the
squeegee.
Clear water filter (Fig. 5/4)
While clear water flows from tank to
brush head, it is cleaned by the filter ele-
ment.
Soiled water drain hose (Fig. 5/5)
This hose allows draining the collected
soiled water from the tank.
Clear water drain hose (Fig. 5/6)
This hose allows draining the clear wa-
ter tank.
Brush ejector (Fig. 5/7)
The brush ejector makes brush removal
fast and easy.
Power connection charger unit (Fig.
5/8)
The power connection supplies the
charger unit with power.
Pedal brush head (Fig. 5/9)
Use this pedal to lift and lower the brush
head.
Pedal plate brush head pressure
(Fig. 5/10)
This pedal allows increasing the ground
pressure of the plate brush head.
19
Operation
Dirt hopper guiding rail (Fig. 6/1)
The dirt hopper located at the cylindrical
broom head is fastened by a guiding
rail. This dirt hopper may be easily re-
moved for cleaning.
Lever for cylindrical broom seating
(Fig. 6/2)
This lever (both sides) is used to re-
lease/lock the cylindrical broom sea-
ting. The cylindrical brooms may be
easily removed without tools.
Swing aside squeegee
Swing aside the squeegee in lifted-out
condition to allow passage through nar-
row clearances. This can be done by
foot or by hand by swinging the squee-
gee to the left in the area of the deflector
bail / deflector roller until the locking pin
(Fig. 6/3) catches. In order to release
locking of the squeegee, actuate the
hand lever (Fig. 5/3) of the squeegee
lift-out (lowering).
Fig.6 1 Dirt hopper guiding rail
2 Lever for cylindrical broom seating
3 locking pin
123
19
Operation
Dirt hopper guiding rail (Fig. 6/1)
The dirt hopper located at the cylindrical
broom head is fastened by a guiding
rail. This dirt hopper may be easily re-
moved for cleaning.
Lever for cylindrical broom seating
(Fig. 6/2)
This lever (both sides) is used to re-
lease/lock the cylindrical broom sea-
ting. The cylindrical brooms may be
easily removed without tools.
Swing aside squeegee
Swing aside the squeegee in lifted-out
condition to allow passage through nar-
row clearances. This can be done by
foot or by hand by swinging the squee-
gee to the left in the area of the deflector
bail / deflector roller until the locking pin
(Fig. 6/3) catches. In order to release
locking of the squeegee, actuate the
hand lever (Fig. 5/3) of the squeegee
lift-out (lowering).
Fig.6 1 Dirt hopper guiding rail
2 Lever for cylindrical broom seating
3 locking pin
123
20
Technical Data
4 Technical Data
Metric unit Plate brush 65 Roll brush 60
Machine length cm 155 164
Machine height cm 111 111
Machine width without Squeegee cm 68 68
Machine width with Squeegee cm 95 95
Working width cm 65 60
Squeegee width cm 95 95
Surface performance theoretical m²/h 3250 3000
Service voltage V 24 24
Nominal power drive motor W 430 430
Nominal power suction motor W 520 520
Nominal power brush motor W 2x720 2x720
Number of brushes Qty. 2 2
Diameter of brushes cm 33 15
Work ride km/h 5 5
Clean water tank litres 70 70
Soiled water tank litres 75 75
Weight without Batteries and water kg 189 181
Weight with water and Batteries kg 388 380
20
Technical Data
4 Technical Data
Metric unit Plate brush 65 Roll brush 60
Machine length cm 155 164
Machine height cm 111 111
Machine width without Squeegee cm 68 68
Machine width with Squeegee cm 95 95
Working width cm 65 60
Squeegee width cm 95 95
Surface performance theoretical m²/h 3250 3000
Service voltage V 24 24
Nominal power drive motor W 430 430
Nominal power suction motor W 520 520
Nominal power brush motor W 2x720 2x720
Number of brushes Qty. 2 2
Diameter of brushes cm 33 15
Work ride km/h 5 5
Clean water tank litres 70 70
Soiled water tank litres 75 75
Weight without Batteries and water kg 189 181
Weight with water and Batteries kg 388 380
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/