Norton BBL1347 Owner's manual

OWNERS MANUAL

Block Buster Large Masonry Saw

Models:

BBL547 BBL527

BBL5247 BBL7247

BBL1347 BBL1327 BBL13247

Form BBL527-1327 Manual Rev 8-2012

2

WARRANTY

Saint-Gobain Abrasives, Inc. (Norton Clipper) Products warrants all

products manufactured by it against defects in workmanship or

materials for a period of one (1) year from the date of shipment to the

customer.

The responsibility of Saint-Gobain Abrasives, Inc. under this warranty

is limited to replacement or repair of defective parts at Saint-Gobain

Abrasives, Inc. Stephenville, Texas factory, or at a point designated

by it, of such part as shall appear to us upon inspection at such point,

to have been defective in material or workmanship, with expense for

transportation borne by the customer.

In no event shall Saint-Gobain Abrasives, Inc. be liable for

consequential or incidental damages arising out of the failure of any

product to operate properly.

Integral units such as gasoline engines, electric motors, batteries,

tires, transmissions, etc., are excluded from this warranty and are

subject to the prime manufacturer's warranty.

This warranty is in lieu of all other warranties, expressed or implied,

and all such other warranties are hereby disclaimed.

Important: Before placing equipment in operation, record the following

information.

MODEL: _________ SERIAL NO.: ___________

PURCHASE FROM: _____________________

ADDRESS: ____________________________

CITY: _______ STATE: ______ ZIP: ________

TELEPHONE NO. ______________________

Before using this equipment, make sure that person using it

Read and understand the instructions in this owner’s manual.

3

Table of Contents

Section Page

I. Preparation 4-16

A. Safety Precautions 4

Dust and Silica Warning 4

B. Assembly 6

C. Assembly Conveyor Cart & Guide a Cut 6-7

D. BBL Series Masonry Saw Specifications 8

E. Electrical Connections 9-10

F. Wiring Diagram 10-14

BBL527, BBL547, BBL5247 5HP 230v/60/1 11

BBL527 3PHASE, BBL547 3PHASE, BBL5247 3PHASE, 5HP 230-460/60/3 W/Switch

BBL727 3PHASE, BBL7247 3PHASE 7.5HP 230-460/60/3 12

BBL727 575V 3PHASE 7.5HP 575v/60/3 13

BBL527 600v 3PHASE 5HP 600/60/3 14

G. Electric Motor Trouble Shooting 15

H. Gasoline Engine 15-16

II. Operation 17-21

A. How To Mount The Blade 17

B. “Step Cutting” With Abrasive Blades 17-18

C. “Jam Cutting” And “Step Cutting With Diamond Blades 18-19

D. Dry Cutting 19

E. Wet Cutting 19-20

III. Maintenance 20-23

A. V-Belts 20-21

B. Electric Motor 20

C. Gasoline Engine 21-22

D. Blade Shaft Bearings 23

E. Water Pump 22-23

IV. Parts List 24-34

A. Ordering Information 24

B. Electric Motor And Gasoline Engine Service Information 24

C. Frame And Water Pump All BBL Models 25-26

D. Cutting Head Gasoline Models 27-29

E. Cutting Head Electric Models 30-31

F. Electric Motor 32

G. Cutting Table All BBL Models 33

H. Guide-A-Cut Assembly All BBL Models 34

Read And Understand Owner’s Manual

Before Use

Safety Alert Symbol: Information Following This Symbol Is Very

Important.

Use Only Genuine Norton Diamond Blades

4

I. PREPARATION

A. Safety Precautions

Important! The following safety precautions must always be observed.

Hazard Symbols

Fuel (gasoline) is extremely flammable and its vapors can explode if

ignited. Store gasoline only in approved containers, in well-ventilated,

unoccupied approved areas, and away from sparks or flames. Do not

fill the fuel tank while the engine is hot or running. Do not start the

engine near spilled fuel.

Never use the fuel as a cleaning agent

Engine components can get extremely hot from operation. To prevent

burns, do not touch the engine or related parts while the engine is

running or immediately after it is turned off. Never operate the engine

with any heat shields or guards removed.

Keep all guards in place when operating any piece of equipment

Keep hands, feet, hair, and clothing away from all rotating parts

Lethal Exhaust Gas use only in well ventilated areas. Engine exhaust

gases contain poisonous carbon monoxide, which is odorless, colorless,

and can cause death if inhaled. Avoid inhaling exhaust fumes, and

never run the engine in a closed building or confined area

Never tamper with the governor components of settings to increase the

maximum speed. Severe personal injury and damage to the engine or

equipment can result if operated at speed above maximum. Always

obey the maximum speed rating of blade.

DO NOT LIFT THE SAW BY THE HANDLE OR

GUARDS!!!

5

Dust and Silica Warning

Grinding/cutting/drilling of masonry, concrete, metal and other materials can generate

dust, mists and fumes containing chemicals known to cause serious or fatal injury or

illness, such as respiratory disease, cancer, birth defects or other reproductive harm. If

you are unfamiliar with the risks associated with the particular process and/or material

being cut or the composition of the tool being used, review the material safety data

sheet and/or consult your employer, the material manufacturer/supplier, governmental

agencies such as OSHA and NIOSH and other sources on hazardous materials and

make certain to comply with all product warnings and instructions for the safe and

effective use of the material being cut. California and some other authorities, for

instance, have published lists of substances known to cause cancer, reproductive

toxicity, or other harmful effects.

Control dust, mist and fumes at the source where possible. In this regard use good

work practices and follow the recommendations of the manufacturer/supplier,

OSHA/NIOSH, and occupational and trade associations. Water should be used for

dust suppression when wet cutting is feasible. When the hazards from inhalation of

dust, mists and fumes cannot be eliminated through engineering controls such as

either vacuum and/or water mist, the operator and any bystanders should always wear

a respirator approved by NIOSH/MSHA for the material being cut.

California Proposition 65 Message

Some dust created by power sanding, sawing, grinding, drilling, and other construction

activities contain chemicals known (to the State of California) to cause cancer, birth

defects or other reproductive harm. Some examples of these chemicals are:

• Lead, from lead-based paints

• Crystalline silica, from bricks and cement and other masonry products

• Arsenic and chromium, from chemically treated lumber

For Addition Information Consult The Following Sources:

http://www.osha.gov/dsg/topics/silicacrystalline/index.html

http://www.cdc.gov/niosh/consilic.html

http://oehha.ca.gov/prop65/law/P65law72003.html

http://www.dir.ca.gov/Title8/sub4.html

Use Approved:

Eye Protection Hearing

Protection Respiratory

Protection Head Protection

6

I. PREPARATION

B. Assembly

1. Remove machine from skid.

2. Remove the conveyor cart and guide-a-cut from the carton and place on the

pan.

3. Remove the drain plug from carton and place in drain opening in bottom of

pan.

4. Check the owner’s manual for wiring connection and proper electrical

connections before starting saw.

C. Assembly Conveyor Cart & Guide-a-Cut

The Block Buster Masonry saws are shipped completely assembled and ready

for use except for diamond blade, gasoline, and oil. Inspect the saw for

shipping damage. If any damage is found, contact the shipper immediately

and file a freight claim. Norton Construction Products is not

responsible for any freight-related damages. Remove the saw from

the pallet.

Items Included with the saw:

Item Part No UPC QTY Notes

Conveyor Cart Assembly 83777 00310007390 1

Guide-A-Cut Assembly 83892 00310007501 1

Splash Guard Assembly 75128 00310004632 1

Wrench 19 mm 70807 00310004053 1

Wrench 22mm 72143 00310004199 1

Water Pump Assembly 72305 00310004237 1 Gasoline Powered Machines Only

Pump Water Electric 214169 70184668392 1 Electric Powered Machines Only

Fit Barb Hose 1/4FPTX1/2 9602010

70184650470

1 Electric Powered Machines Only

Owner’s Manual Form BBL527-

1327 -NA-

1 Form BBL527-1327 Manual Rev 4-

2012

Diamond Bade

1 General Propose Same Diameter as

Blade Size

Do not install the blade until it is time to use the saw!

ANSI regulations prohibit the transportation of any concrete saw with

the blade installed!

7

Conveyor Cart Assembly:

Remove the Conveyor Cart and Back Stop from the Saws Water Pan, and the

Wing Nuts, Carriage Bolts, Washers, and Cart Stop from the plastic bag. Slide

one (1) Carriage Bolt thru each of the three (3) Square Holes located on the

front of the Conveyor Cart. Slide the Back Stop Over each of the Carriage

Bolts. Slide the Stop Assembly over the Carriage Bolt Located on the Left front

of the Conveyor Cart NOTE: The Rubber Stop will faces away from the

Conveyor Cart. Attach one (1) Washer and one (1) Wing Nut to each Carriage

Bolt and Tighten. See Figure 1: Back Stop Assembly. Place the Conveyor

Cart on the Machine.

Figure 1: Back Stop Assembly

Guide-A-Cut Assembly:

Attach the Guide-A-Cut to the Conveyor Cart by adjusting the Wing Bolt until

the Guide-A-Cut can slide over the Black Stop. The Guide-A-Cut will work as a

Rip Guide that is adjustable for 90 and 45 cuts. See Figure 2: Guide-A-Cut

Assembly.

Figure 2: Guide-A-Cut Assembly

Splash Assembly:

Remove the Splash Guard from the Saw Water Pan. Attach the Splash Guard

Spring Clips to the Pivoting Bar Located Under the Cutting Head. Note that the

rough side of the Splash Guard should face towards the front of the saw. The

Splash Guard material is made is designed for easy to cleaning. To clean,

simply rinse the Splash Guard with water until clean. The Splash Guard should

be used when wet cutting to reduce the amount of debris thrown from the blade

and cutting surface. When dry cutting the Splash Guard can be removed to

allow the dust particles to drift away from the Saw Operator.

8

I. PREPARATION

D. BBL Series Masonry Saw Specifications

Dimensions/Weight

Length 41” (1041mm)

Width 26” (660mm)

Height (Electric) 54” (1372mm)

Height (Gas) 57” (1448mm)

Weight (Electric) Uncrated 440lbs (970kg)

Weight (Gas) Uncrated 460lbs (1014kg)

Electric Motor

Motor Mfg. Baldor

Motor Type TEFC, Thermal Protection

Motor RPM 3,450 RPM

Single Phase:

BBL527

BBL547

BBL5247

5 HP - 230v 60 Hz single Phase (Standard)

Run Amperage: 20.6 Amp @ 230v

Three Phase 5 Horse Power

BBL527 3PHASE

BBL547 3PHASE

BBL5247 3PHASE

5 HP - 230-460v 60Hz three Phase (Optional)

Three Phase 7-1/2 Horse Power

BBL727 3PHASE

BBL7247 3PHASE

7-1/2 HP 230-460v 60Hz three Phase

Run Amperage: 8.4 Amp @ 230v/4.2 Amp @ 480v

Three Phase 7-1/2 Horse Power 575v

BBL727 575v 3PHASE 7-1/2 HP 575v 60Hz three Phase (Optional)

Thee Phase 5 Horse Power 600v

BBL527 600v 3PHASE 5 HP - 600v 60 Hz single Phase (Optional)

Engine (Gasoline Models Only)

Engine Mfg. Honda

Spec No. GX390K1QXC9

Model GX390

Engine Type Single Cylinder 4 Cycle

Horse Power 13 hp (9.5kW) @ 3,600 rpm

Max Torque 19.5 ft-lbs (26.5 Nm, 2.7 kg-m) @ 2,500 rpm

Cooling System Air

Oil Capacity 1.1 liter (1.16 US qt)

Fuel Capacity 6.5 liter (1.79 US gal)

Fuel Type Unleaded Gasoline (86 pump octane)

Low Oil Sensor Yes

Air Filtration Four Stage Cyclone

Characteristics

Max Blade 20” (508 mm) or 14” (356 mm)

Depth of Cut 24” (610 mm) 10” (254 mm)

20” (508 mm) 8” (203 mm)

14” (356 mm) 5” (127 mm)

Arbor Bore 1” (25.4 mm)

Blade Shaft Locking Device Machined Into Flats Of Tight Collar

Blade Shaft Speed 24” 1938 rpm

20” 2400 rpm

14” 2900 rpm

Depth Control Hand Feed With Return Spring

Depth Lock Standard

Number Of V-Belts 2

Blade Guard Type All Steel Construction

Stay Level Blade Guard Yes

Fork Lift Brackets Built In

Water Pump (Gasoline Models) Mechanically Belt Driven

Water Pump (Electric Models) Electrical 115v/60Hz

9

I. PREPARATION

E. Electrical Connections

Important Before connecting the motor leads to the power supply, be sure that

the voltage, cycles and phase shown on the nameplate of the motor correspond to

the available power supply. Both the 5 HP and 7-1/2 HP. motors have overload

protectors and are equipped with a reset button on the motor housing. If, after

proper electrical connections are made, the motor will not run, press the reset

button to the overload protector switch. The optional 575v and 600v Three (3)

Phase motors do not have a thermal over load protector.

Failure to run the motor on the proper voltage will damage the motor and is not

covered under warranty. Improperly wired motors are not covered under warranty.

Voltage Selection for Three (3) Phase Motors 5 and 7-1/2 HP 230-480v:

Wherever possible, use 480v power supply for best operation. To change

voltage, disconnect the power form the machine, remove the terminal box cover

from the top of the motor, and change the connections as shown in the wiring

diagrams on page 12 or the chart below.

Line A Line B Line C Join Join Join Join Join Join

High (480v) 1 2 3 4,7 5,8 6,9 10 11 12

Low (230v) 1,7 2,8 3,9 10,4 11,5 12,6 – – –

Power Connections

Connect the power supply to the pigtail leads of the switch. Direct wiring

connection is preferred, but an extension cord with an electrical plug with 30 amp

minimum capacity may be used. Connecting wires should be as short as possible

and in one piece. In no case should the connecting wires be longer than shown in

the following table:

Model HP Volts Phase 50’ (15m) 100’ (30.4m) 150’ (45.7m)

BBL527

BBL547

BBL5247

5 HP 230v 1 12 AWG 12 AWG 10 AWG

BBL527 3PHASE

BBL547 3PHASE

BBL5247 3PHASE

5 HP 230-480v 3 12 AWG 12 AWG 10 AWG

BBL727 3PHASE

BBL7247 3PHASE 7.5 HP 230-480v 3 12 AWG 12 AWG 10 AWG

BBL727 575v 3PHASE 7.5 HP 575v 3 12 AWG 12 AWG 10 AWG

BBL527 600v 3PHASE 5 HP 600v 3 12 AWG 12 AWG 10 AWG

Caution-When wires that are too small gauge or too long are used, loss of power,

over heating, or possible damage to the motor will result.

Always use the proper wiring connectors that are UL/CSA approved to attach the motor to

the electrical supply. Any wiring hook ups should be made by qualified personnel and made

to National Electrical Code and to any Local Codes.

10

Generators:

If a generator must be used, it must be the minimum size listed below or greater.

The generator must have a 30A circuit and capable of providing a minimum of

wattage at the required voltage. Under size generators will cause motor damage

and is not covered under warranty.

Motor HP Minimum Generator Size

5 HP 230v 17.6 Kw

5 HP 230-460v 3 Phase 15.2 Kw

7-1/2 HP 230-460v 3 Phase 22.6 Kw

5 HP 600v 3 Phase 15.2 Kw

7-1/2 HP 575v 3 Phase 22.6 Kw

I. PREPARATION

F. Wiring Diagram

Model Part#

UPC#

Description

HPVolts Hz PH Baldor

Specification Baldor

Drawing

BBL527

BBL547

BBL5247 232088

00510003898

MOT 5.0HP 230v/60/1 W/Switch

5

230v

60

1 36J656Y959

CD1122

BBL527 3PHASE

BBL547 3PHASE

BBL5247 3PHASE 232099

70184683437

MOT 5HP 230-460/60/3 W/Switch

5230-

460v

60

3 36H968W189G1

CD1597

BBL727 3PHASE

BBL7247 3PHASE 232100

70184683438

MOT 7.5HP 230-460/60/3

W/Switch 7.5230-

460v 60 3 36K167T227

CD1597

BBL727 575v

3PHASE 232157

70184627209

MOT 7.5HP 575/60/3 W/Switch

7.5575v 60 3 36N332S715

CD0003A02

BBL527 600v

3PHASE 23215

70184626967

MOT 5HP 600/60/3 W/Switch

No Thermal Overload Protector 5 600v 60 3 36H968T894 CD0383A02

Before attempting any electrical work always verify the voltage, phase, and Baldor

Motor Specification from the Motor Name Plate with the Chart Shown Above. Any

failure due to misapplication of voltages and or Phase is not covered under any

warranty.

For any Electric Motor service, warranty, or technical related questions contact your nearest

Baldor service center:

Baldor Electric Company

Corporate Headquarters

5711 R.S. Boreham, Jr. St.

P.O. Box 2400

Fort Smith, AR 72901

Phone: (501) 646-4711

Fax: (501) 648-5792

Web: http://www.baldor.com

11

Wiring Diagram 5HP 230v/60 hz/1 Phase

Model Motor

Part# Motor UPC#

Description

HP Volts Hz PH Baldor

Specification Baldor

Drawing

BBL527

BBL547

BBL5247 232088

00510003898

MOT 5.0HP 230v/60/1 W/Switch

5

230v

60

1 36J656Y959

CD1122

12

Wiring Diagram 5HP & 7-1/2 HP 230-460v/60Hz/3 Phase

Model Motor

Part# Motor UPC#

Description

HP Volts Hz PH Baldor

Specification Baldor

Drawing

BBL527 3PHASE

BBL547 3PHASE

BBL5247 3PHASE 232099

70184683437

MOT 5HP 230-460/60/3 W/Switch

5230-

460v

60

3 36H968W189G1

CD1597

BBL727 3PHASE

BBL7247 3PHASE 232100

70184683438

MOT 7.5HP 230-460/60/3 W/Switch 7.5230-

460v 60 3 36K167T227

CD1597

NOTE: High Voltage = 460v, Low Voltage =230v. Unit normally ship configured for low voltage (230v).

13

Wiring Diagram 7-1/2 HP 575v/60Hz/3 Phase

Model Motor

Part# Motor UPC#

Description

HP Volts Hz PH Baldor

Specification Baldor

Drawing

BBL727 575V

3PHASE 232157

70184627209

MOT 7.5HP 575v/60/3 W/Switch

7.5 575v 60 3 36K167T227

CD1597

14

Wiring Diagram 5 HP 600v/60Hz/3 Phase

Model Motor

Part# Motor UPC#

Description

HP Volts Hz PH Baldor

Specification Baldor

Drawing

BBL527 600v

3PHASE 23215

70184626967

MOT 5HP 600/60/3 W/Switch

No Thermal Overload Protector 5 600v 60 3 36H968T894 CD0383A02

15

G. Electrical Motor Trouble Shooting:

Circuit Breaker During Start Up or Not Cutting:

 Verify that the power supply voltage matches the motor name plate

voltage

Failure to run the motor on the proper voltage will damage

the motor and is not covered under warranty. Improperly

wired motors are not covered under warranty.

 Verify that the circuit breaker is at least 30 amps

 Verify that the Extension Cord meets the requirements on See:

Power Connections page 9

 Have a qualified Electrician verify that the Electrical Connections are

correctly made.

 If using a generator verify that it meets the minimum requirements

See: Generators on page 9

Circuit Breaker Trips while cutting: - This is an issue with the Blade or Cutting

Method being used.

 Verify that the Blade Being used is correct for the material being cut

 Verify that the Blade is properly exposed

 Verify that the Blade is installed properly

 Verify the cutting method. Forcing the Blade into the material is a

sign that either the Blade is NOT correct for the material being cut or

an inexperienced operator. Let the Blade and Machine work for you

do not work for the Blade and Machine.

Overload Protector (Thermal) Trips – This is a sign of Low Voltage, Incorrect

Blade for Material being cut, or forcing the Blade through the material.

 Verify Voltage at the machine!

 Verify that the Extension Cord meets the requirements on See:

Power Connections page 9

 Verify the cutting method. Forcing the Blade into the material is a

sign that either the Blade is NOT correct for the material being cut or

an inexperienced operator. Let the Blade and Machine work for you

do not work for the Blade and Machine.

 Clean Motor by blowing out the fan cover with compressed air

 Check the Motor for a damaged fan

G. Gasoline Engine

Prior to attempting to operate the engine, read the information contained in

the engine owner's manual. An engine owner’s manual is supplied with

every gasoline powered concrete saw.

1. Check Oil: Add oil if low. Refer to the engine owner's manual for the

recommended SAE viscosity grades. Capacity of oil is 1.1 liters (1.16 US qt)

16

2. Check Fuel: Fill if low. Use only unleaded gasoline with a pump sticker

octane rating of 86 or higher is recommended. Never use an oil and gasoline

mixture!

3. Air Cleaner: Never run the engine without the air cleaner! Rapid engine wear

will result from contaminants being drawn through the carburetor and into the

engine.

4. Engine Starting: Refer to the engine owner's manual for proper engine

starting procedure.

The head on the Gasoline Powered Saw should only rise to a

maximum of nine (9) inches above the surface of the Cutting

Table

For any Engine service, warranty, or technical related questions please contact

your nearest Honda service centers:

Honda Power Equipment Group

4900 Marconi Dr.

Alpharetta, GA 30005-8847

Tel: (800) 426-7701

Fax: (678) 339-2670

Web page: http://www.honda-engines.com/dis.htm

17

II. OPERATION

A. How to Mount Blade

Be sure blade shaft collars and arbor are free of dirt and all foreign material before

mounting blade on the arbor shaft. Tightening blade against an uneven surface

can cause fracture of an abrasive blade or cause to run-out of alignment, causing

excessive blade wear.

When tightening bolt against outside blade shaft collar, be sure to tighten enough

to hold the blade firmly without slipping but do not over tighten excessive

tightening can cause fracture of abrasive blades.

Using blade shaft wrench (in bracket) remove the blade shaft bolt and loosen

collar.

Place the blade on the arbor, and attach the loose collar and tighten the blade

shaft bolt securely.

B. "Step Cutting " With Abrasive Blades

Use "step cutting" without exception when cutting wet or dry with abrasive

blades. "Jam cutting", which is discussed and illustrated in the section following,

is to be used only with wet and dry cutting diamond blades.

1. Clamp and hold material firmly against the backstop on conveyor cart. Be

certain the material does not slip or rock during cutting operation, as this can bind

blade, causing excessive wear and fracture.

2. Move the conveyor cart near the blade, and pull down on the head until the

blade is lowered to a point where it will lightly contact the top of the material. Then

18

start "step cutting" - which means passing the material beneath the blade with

rapid , (50 to 60 strokes per minute) full length strokes, taking a shallow cut

(approximately 1/8" deep ) on the forward, and also on the backward stroke.

Complete each rapid stroke backward and forward, by passing the material

beyond the center of the blade before starting the reverse movement of the cart.

The harder the material, the more rapid the forward and backward strokes.

3. "Step cutting as can be seen in the sketch below, lessens the area of the blade

circumference in contact with the material, keeping the blade cool, running free,

and cutting at peak efficiency. Don't get the impression "step" cutting means slow

cutting - actually it is 6 times faster than trying to "force" the cut by strong-arming

the material through the blade. Forcing the blade through with a deep cut causes

a longer area of the blade circumference to be in contact with the material, causing

excessive friction heat to be generated, which then causes the blade to "smear"

or "load" with fused material particles and lose its sharp cutting surface. (Note: If

improper operation should cause an abrasive blade to "smear", make several cuts

through a soft brick to "dress” the blade back to good cutting performance.)

C. "Jam Cutting" and "Step Cutting" With Diamond Blades

In "Jam" cutting the head is locked in a fixed position and the material is pushed

into it as shown in the sketch at the bottom. "Jam" cutting with the head locked in

a fixed position usually provides greater efficiency.

1. To lock the head into position, tighten the lever nut at the back of the saw.

2. "Step" cutting with diamond blades is done by applying more pressure to the

blade. Unlike "step" cutting with abrasive blades, "step" cutting with diamond

blades requires only a few passes through the material.

3. In cutting, clamp the material securely and hold it firmly against the conveyor

cart backstop. If the material is allowed to slip, resulting seizure of the blade may

bend the diamond blade steel center or cause a ring section to be twisted off.

4. Do not force the material or bump into the blade. When nearing completion of

the cut, retard and slightly hold back the conveyor cart. If this is not done, the

material may be pulled into the blade so fast that excessive pressure on the rim

may cause warping or twisting of the rim section.

19

5. When a new diamond blade is broken in, make the first few cuts slowly until the

blade cuts freely and easily.

6. When the blade is cutting freely and easily. Use it! As long as it cuts

satisfactorily do not dress the diamond blade or remove it from the blade shaft.

7. After continuous cutting of extremely hard and dense materials, the blade may

slow down and it may be necessary to "dress" the cutting edge. To do this:

a. Use a rapid "step" cutting method for a few cuts - push the material

back and forth under the blade while it is cutting down. If this is not

sufficient:

b. Make one or two cuts in a soft brick or light weight block.

However, "dressing" should be done as seldom as possible - because too

much "dressing" reduces blade life.

D. Dry Cutting

1. Use a proper blade, which is marked for dry cutting.

2. Remove the water curtain.

3. Disconnect the water pump.

4. Use "step" cutting as explained previously when using abrasive blades.

5. Use "jam" or "step" cutting when using dry cutting diamond blades.

E. Wet Cutting

Water may be supplied either by filling the water pan to within a half-inch of the top

(for continuous use of the same water) or by placing a barrel of water next to the

saw (for continuous flow of clean water). When using water from a barrel, remove

water from pan and submerge it in water barrel. Remove the drain plug so the

used water and sludge will drain from pan.

1. Prepare water supply.

2. Install water curtain on cutting head pivot bar.

20

3. The saw uses a belt driven mechanical pump which only operates when the

engine/motor is running.

4. Handle on petcock should be turned in line with the water flow. Start motor and

be certain that both sides of the blade are getting water.

5. Be sure that the water covers the bottom of the pump at all times. Do not let

sludge and dirt get deep enough in the pan to block the pump inlet.

6. Use "step" cutting with abrasive blades as previously directed.

7. Use "jam" cutting or "step" cutting with diamond blades as previously

described.

III. MAINTENANCE

The saw requires very little maintenance for long satisfactory operation. However,

the following points must be watched:

A. V-Belts

The drive belts are made of premium oil and heat resistant materials. They require

very little adjustment, but should be tightened after the first few days of running.

Adjustment and Alignment

Warning: Never make adjustments to v-belts and pulleys while engine is running.

1. The best tension for a v-belt drive is the lowest tension at which the belts will

not slip under full load.

2. Simply take up the drive until the belts are snug in the grooves. Run the drive

for about 15 minutes to "seat" the belts. Then impose the peak load. If the belts

slip, tighten them until they no longer slip at peak load.

3. Remember, too much tension shortens belt and bearing life.

4. Check belt tension frequently during the first day of operation. Check belt

tension periodically thereafter and make any necessary adjustments.

5. The two most common causes of misalignment are shown in the drawing.

a). The engine drive shaft pulley and the blade shaft are not parallel. See figure I

b). The pulleys are not located properly on the shafts. (See figure 2)

6). To check alignment, all you need is a steel straight edge.

7). Line up the straight edge along the outside faces of both pulleys as shown in

the drawing.

8). Misalignment will show up as a gap between the pulley face and the straight

edge.

9). Make sure that the width of the outside land is equal on both pulleys.

Page is loading ...

Norton BBL1347 Owner's manual

This manual is also suitable for

Norton BBL1347 Owner's manual

Related papers

Other documents