Chief PNRUB-G Installation guide
- Category
- Wall & ceiling mounts accessories
- Type
- Installation guide
This manual is also suitable for
PNR Series Installation Instructions
2
DISCLAIMER
Milestone AV Technologies and its affiliated corporations and
subsidiaries (collectively "Milestone"), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Chief®, ClickConnect™ and Centris Select™ are registered
trademarks of Milestone AV Technologies. All rights reserved.
DEFINITIONS
MOUNTING SYSTEM: A MOUNTING SYSTEM is the
primary Chief product to which an accessory and/or component
is attached.
ACCESSORY: AN ACCESSORY is the secondary Chief
product which is attached to a primary Chief product, and may
have a component attached or setting on it.
COMPONENT: A COMPONENT is an audiovisual item
designed to be attached or resting on an accessory or mounting
system such as a video camera, CPU, screen, display,
projector, etc.
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all mounting systems
are properly assembled and installed using the instructions
provided.
WARNING: Failure to provide adequate structural strength
for this mounting system can result in serious personal injury
or damage to equipment! It is the installer’s responsibility to
make sure the structure to which this mounting system is
attached can support five times the combined weight of all
equipment. Reinforce the structure as required before
installing the mounting system. The wall to which the mount
is being attached may have a maximum drywall thickness of
5/8” (1.6cm).
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components attached to this mount does not exceed
200 lbs (90.7 kg).
WARNING: Use this mounting system only for its intended
use as described in these instructions. Do not use
attachments not recommended by the manufacturer.
WARNING: Never operate this mounting system if it is
damaged. Return the mounting system to a service center for
examination and repair.
WARNING: Do not use this product outdoors.
IMPORTANT ! : The PNR Series mounts has been designed
to be mounted onto a 2" x 4" (51mm x 102 mm) 16" on center,
wood stud wall.
NOTE: The PNR Series includes:
•Accessory Model PNR2000 (to be used with UL Listed
Chief accessory PSBU interface bracket--not
included).
•Model PNRU which includes the UL Listed Chief
accessory PSBU interface bracket.
--SAVE THESE INSTRUCTIONS--
Installation Instructions PNR Series
3
DIMENSIONS
Mounting Pattern
25
1.001.00
2546
19.69
500
16.00
406
7.00
178
1.81
19.00
483
538
21.19
38
4
.18
1.50
.40
10
NOTE:
PSBU INTERFACE BRACKET
NOT SHOWN. THE PSBU INTERFACE
BRACKET WILL ADD 1” IN DEPTH
AND MAY AFFECT THE LOCATION
OF THE DISPLAY ON THE MOUNT.
DIMENSIONS: [MILLIMETERS]
INCHES
PNR Series Installation Instructions
4
DIMENSIONS -- cont’d
Retracted
25.00
635
2°
TiltedDown
17°
U
nit
Dept
h
T
il
t A
dj
u
s
tmen
t
*
Roll Adjustment
Extended
83
3.25
27.06
687
Highest Height Setting
1.53
39
Lowest Height Setting
2.61
66
Tilted Up
*The range of adjustment will v ary with different size s creens
5°
10.84
76.17°
MAX
76.17°
MAX
22.65
MAX
161.09°
MAX
90.00°
18.21
DIMENSIONS: [MILLIMETERS]
INCHES
Installation Instructions PNR Series
5
LEGEND
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
Pencil Mark
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Marquage au crayon
Drill Hole
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Percez un trou
Adjust
Ajustar
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
PNR Series Installation Instructions
6
TOOLS REQUIRED FOR INSTALLATION
PARTS
7/32" (5.5mm) #2 9/16"
A (1)
[PNR assembly]
B (2)
[Cover]
C (2)
[End cap] D (2)
[End cap]
E (1)
[Adjustment wrench] G (4)
J (12)
5-1/2" Cable tie
F (1)
[Adjustment insert]
H (4)
5/16 x 3-1/2"
K (1)
[PSBU bracket]
(Only included with PNRU)
[Installation washer]
L (2)
[Cable clip]
Installation Instructions PNR Series
7
Installing Mount to Wall
WARNING: IMPROPER INSTALLATION CAN LEAD TO
MOUNT FALLING CAUSING SERIOUS PERSONAL
INJURY OR DAMAGE TO EQUIPMENT! It is the installer’s
responsibility to make sure the structure to which the mount
is being installed is capable of supporting five times the
combined weight of the mount and all attachments.
NOTE: The following instructions assume a suitable mounting
structure and surface exists prior to installation.
CAUTION: To avoid personal injury, use an assistant when
lifting, lowering or holding PNR during installation.
1. Determine mounting location taking into consideration
display size and PNR’s range of movement.
2. Using a stud sensor locate two wood studs 16” on center.
(See Figure 1)
Figure 1
3. Place and level mount against wall, aligning mounting holes
in upper and lower wall channels with studs. (See Figure 1)
4. Mark four mounting holes making sure mounting holes are
located as close as possible to center of studs.
(See Figure 1)
5. Drill four 7/32" pilot holes where the mounting holes were
marked. (See Figure 1)
6. Partially install two 5/16" x 3-1/2" lag bolts (H) into upper
pilot holes. DO NOT tighten at this time. (See Figure 2)
7. Align mounting holes in upper wall channel with lag bolts,
and hang mount on lag bolts.
8. Adjust mount lateral position left until lag bolts are seated in
mounting slots in upper wall channel. (See Figure 2)
9. Place two installation washers (G) over two lag bolts (H).
(See Figure 2)
10. Install two 5/16" x 3-1/2" lag bolts (H) through mounting holes
in lower wall channel and into pilot holes. (See Figure 2)
11. Place two installation washers (G) over two lag bolts (H).
(See Figure 2)
12. Tighten all hardware. DO NOT over tighten!
Figure 2
Adjusting PNR Height
NOTE: Height adjustment range up to 1.08 inches.
1. Check PNR for the desired height. If needed, use the
adjustment wrench (E) to adjust the PNR height. (See
Figure 3)
•Turn adjustment nut clockwise to lower the unit height,
or
•Turn adjustment nut counterclockwise to raise the unit
height.
Figure 3
1
3
4
5
x 4
3
6
(H) x 4
10
(G) x 2
8
(G) x 2
9
11
Adjustment nut
1
Lower
Raise
PNR Series Installation Instructions
8
Installing Covers and End Caps
NOTE: The covers and end caps have pressure fitting ends
that lock into place with each other.
1. Install cover (B) over the top bracket. (See Figure 4)
2. Install end caps (C and D) into the cover and top bracket.
(See Figure 4)
3. Repeat Steps 1 and 2 for the lower mounting bracket. (See
Figure 4)
Figure 4
Mounting the Display
WARNING: IMPROPER INSTALLATION CAN LEAD TO
MOUNT FALLING CAUSING SEVERE PERSONAL INJURY
OR DAMAGE TO EQUIPMENT. Displays can weigh in
excess of 40 lbs (18.1kg). ALWAYS use two people and
proper lifting techniques when installing display.
1. Install PSBU interface bracket (K - included with PNRU
only) to display using hardware and installation instructions
included with PSBU bracket.
2. Move faceplate to extended position by grasping faceplate
and pulling outward away from wall.
WARNING: IMPROPER INSTALLATION CAN LEAD TO
MOUNT FALLING CAUSING SEVERE PERSONAL INJURY
OR DAMAGE TO EQUIPMENT. Make sure mounting buttons
on display are properly seated in mounting holes in faceplate.
3. While supporting both sides of display, align four mounting
buttons on display or interface bracket with four mounting
holes in faceplate. (See Figure 5) and (See Figure 6)
4. Lower display into place listening for audible "click" to
ensure recessed area of mounting buttons are properly
seated in lower area of mounting holes and ClickConnect
mechanism engages. (See Figure 5) and (See Figure 6)
NOTE: Holes are provided in the faceplate for use with a
padlock or similar locking device, if desired. In addition,
the pin and nut may be removed from the upper holes
and moved to the lower holes for use as a more
permanent locking device. (See Figure 6)
Figure 5
Figure 6
1
2
2
(B)
(D)
(C)
3
4
4
3
To use as a
more permanent
lock, remove pin
and nuts and move
to lower holes.
A padlock or bolt may be
placed through latch holes.
Installation Instructions PNR Series
9
Cable Management
WARNING: IMPROPER INSTALLATION CAN LEAD TO
SERIOUS PERSONAL INJURY OR DAMAGE TO
EQUIPMENT! Make sure cables do not run through pinch
points.
1. Thread cable ties (J) under cable clamps in mount arms.
(See Figure 1)
Figure 7
2. Route power/audio/video cables through the cable channel
in top arm (See Figure 7), allowing sufficient slack in cables
for left / right movement of display and swing arm, as well
as swing arm extension and retraction.
3. Secure cables to top arm using two cable ties (J).
4. Repeat Steps 1 through 3, as necessary, for remaining top
arm and lower arms.
WARNING: IMPROPER INSTALLATION CAN LEAD TO
SERIOUS PERSONAL INJURY OR DAMAGE TO
EQUIPMENT! DO NOT route cables through holes in
faceplate.
5. (Optional) Install two cable clips (L) into holes on connector
bracket. (See Figure 8)
Figure 8
Cable clamps
Cable tie
1
Cable tie
Top view
(top view)
(L) x 2
connector
bracket
PNR Series Installation Instructions
10
Tension Adjustments
Vertical Tilt Tension Adjustment
1. With display mounted, check for desired vertical tilt tension.
2. Adjust the Centris Select knob until desired vertical tilt
tension is obtained. (See Figure 9)
3. To lock the mount at the desired vertical tilt, tighten the
vertical tilt lock screw. (See Figure 10)
Figure 9
Figure 10
Swivel Tension Adjustment
CAUTION: DO NOT OVER TIGHTEN SWIVEL
ADJUSTMENT NUT. Over tightening swivel adjustment nut
will cause excessive wear and may distort adjustment
components.
1. Using a 9/16” wrench (not provided), slightly tighten or
loosen swivel tension adjustment nut. (See Figure 11)
2. Repeat until desired tilt tension is obtained.
Roll Tension Adjustment
1. If necessary, loosen or tighten roll tension adjustment nut.
(See Figure 11)
2. Repeat until desired rotational tilt tension is obtained.
Figure 11
Centris Select
adjustment knob
Vertical tilt
lock screw
Roll tension
adjustment nut
Swivel tension
adjustment nut
Installation Instructions PNR Series
11
Swing Arm Adjustments
The dual swing arms are shipped installed in the center of the
top and bottom mounting brackets, which is the standard
mounting configuration.
The top and bottom mounting brackets have slotted holes,
allowing for lateral adjustment of the dual swing arms.
After installing top and bottom mounting brackets between two
wood studs 16” on center, the swing arms can be adjusted or
moved off center, depending on the location of the mount, size
of display, and lateral movement needed to rotate the display.
The swing arms can be adjusted, as follows:
•Adjusting the Swing Arms Off-Center
With no disassembly required, you can adjust the
swing arms up to 1-inch to the left of center or up to
1-inch to the right of center.
•Reconfiguring the Swing Arms Left of Center
With some disassembly and reassembly required, you
can move the swing arms to the left of center by
reconfiguring the mount. Use the first and third slotted
holes in the top and bottom mounting brackets.
•Reconfiguring the Swing Arms Right of Center
With some disassembly and reassembly, you can
move the swing arms to the right of center by
reconfiguring the mount. Use the third and fifth slotted
holes in the top and bottom mounting brackets.
Adjusting the Swing Arms Off Center
1. Remove the display from the mount.
2. Loosen four bolts (two on the top and two on the bottom)
securing the swing arm assembly to top and bottom
mounting brackets (See Figure 12).
3. Move the swing arm assembly left or right within slots to
desired location.
4. Tighten the bolts.
5. Install the display on the mount.
Figure 12
Reconfiguring the Swing Arms to Left or Right of
Center
1. Remove the display from the mount.
WARNING: The next step will release the arm assembly
from the mount. The arms and plate may fall if you are not
careful.
2. Remove four bolts (two on the top and two on the bottom)
securing the swing arm assembly to the top and bottom
mounting brackets. (See Figure 3)
Figure 13
3. Move the swing arm assembly left or right within slots to
desired location.
•Left of Center (See Figure 3).
•Right of Center (See Figure 14).
4. Install four bolts (two on the top and two on the bottom) to
secure the swing arm assembly to the top and bottom
mounting brackets.
5. Tighten the bolts.
6. Install the display on the mount.
Figure 14
Top bolts
Top bolts
Top bolts
PNR Series Installation Instructions
12
Swing Arm Tension Adjustment
Swing arm tension is pre-set at the factory and is adjusted to
accommodate displays with weights near the top of the mount’s
capacity.
If smaller displays are used it may be difficult to reposition the
display after mounting.
NOTE: The display must be mounted prior to adjusting swing
arm tension.
To adjust swing arm tension to compensate for smaller display:
1. Place adjustment insert (F) into tension adjustment screw
located at swing arm pivot point. (See Figure 15)
NOTE: The display may need to be repositioned in order to
gain access to the tension adjustment screw(s).
2. Use the adjustment wrench (E) provided with the mount,
turn adjustment insert clockwise to increase swing arm
tension (See Figure 16) or counterclockwise to reduce
swing arm tension. (See Figure 17)
NOTE: Small adjustments of 1/8 turn or less are typically all
that is required to achieve desired tension.
3. Check swing arm tension. If desired tension is present,
tension adjustment is complete. If additional tension
adjustment is required, repeat steps 1 and 2 until desired
tension is achieved.
NOTE: If changing from a smaller display to a larger display it
may be necessary to increase swing arm tension.
Figure 15
Figure 16
Figure 17
Tension adjustment
screw
(E)
(F)
Increase tension
Reduce tension
Installation Instructions PNR Series
13
Removing Display from Mount
1. Remove bolt or padlock from faceplate (if used).
NOTE: The pin may have been used as a more permanent
locking device. If so, remove nut and pin and move
from the lower holes to the upper holes.
2. Pull back on flag on upper mounting hole and press pin
down into "Open" position. (See Figure 18)
WARNING: DISPLAY MAY WEIGH IN EXCESS OF 40
LBS! Always use two people and proper lifting techniques
when installing or positioning display on mount.
Figure 18
3. Carefully lift display from mount
4. Lift up on pin and place flag back against faceplate to return
it to "Closed" position. (See Figure 19)
Figure 19
2
1
Remove bolt
or padlock
if used.
Pin in
"Closed"
position -
move to
"Open"
position to
remove
display.
Pin in
"Open"
position -
4
move to
"Closed"
position
after display
is removed.
PNR Series Installation Instructions
14
Installation Instructions PNR Series
15
USA/International A 6436 City West Parkway, Eden Prairie, MN 55344
P800.582.6480 / 952.225.6000
F877.894.6918 / 952.894.6918
Europe A Franklinstraat 14, 6003 DK Weert, Netherlands
P+31 (0) 495 580 852
F+31 (0) 495 580 845
Asia Pacific A Office No. 918 on 9/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P852 2145 4099
F852 2145 4477
PNR Series Installation Instructions
Chief, a products division of
Milestone AV Technologies
8800-002682 Rev01
2016 Milestone AV Technologies
www.milestone.com
07/16
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
Chief PNRUB-G Installation guide
- Category
- Wall & ceiling mounts accessories
- Type
- Installation guide
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Chief PNRUB-G User manual
-
Chief Manufacturing PNR Series User manual
-
-
Chief MIWRFUB Installation guide
-
-
-
-
-
-