GFW GFW 2 Wall Mounted Bedside Table Set User manual

Type
User manual

This manual is also suitable for

HARMONY
Bedside
Issue 1 - 10/09/21
IMPORTANT - Retain these instructions for future reference
x 2 30 min
Set Up
Safety
Important - Please read these instructions fully before starting assembly
• WARNING: To prevent
falling down, these units must
be secured to a wall using the
brackets supplied.
• A unit that is allowed to topple
can cause serious or fatal injury.
In addition to wall fixing the unit,
place heavy items on the lower
shelves, do not put any heavy
objects on top of the unit and
never allow children to climb or
hang on drawers, doors or
shelves.
• Refer to guide after section 16
for wall fixing information.
• Warning: Each unit weighs
approximately 8 kgs.
Please lift with care.
• Assembly to be carried out by
a competent adult only.
• During assembly children
should be kept away from the
product due to possible risk of
injury.
• Installation shall only be
carried out exactly according to
the manufacturer’s instructions -
otherwise a safety risk can
occur if incorrectly installed.
• Do not use this item if any
components are missing or
damaged.
• Regularly check all fastenings
to ensure they are properly
tightened.
Care Advice
• Check you have all the
components and tools listed on
relevant pages.
• Remove all fittings from the
specified plastic bag and
separate them into their groups.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
• Assembly videos are
available throughout
these instructions by
scanning in the QR
codes.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Dispose of all packaging
carefully and responsibly.
• Only clean with a damp cloth.
Cabinet Panels
Drawer Panels Note: the internal drawer panels are grey
725 x 10.5cm x 2
WRP-00000637
639.1 x 15.8cm x 2
DF-00026196
136 x 32.8cm x 2
DF-00026191
236 x 32.8cm x 2
DF-00026192
339.5 x 29.5cm x 2
DF-00026190
439.5 x 32.7cm x 2
DF-00026193
539.5 x 19.3cm x 2
DF-00026194
825 x 10.5cm x 2
WRP-00000638
936.45 x 10.5cm x 2
WRP-00000638
10 37.55 x 24.7cm x 2
TDF-00026211
Fittings Use these drawings to
correctly identify the fittings
Tools
Only used for
drilling walls
F171GY
Bag 2
Dx 4 Fx 8
A
F901
Ax 4 E
F639
x 6
F607
Bag 1
A
F901
F22
Ax 24 Cx 24
Bx 24
F900
R
L
x 2
H
J38700
F529
Gx 4
Bag 3
1
2
Set aside 1 of every panel and half of all fittings to be used
later to assemble the 2nd bedside
Important: Fittings for both bedsides are packed together.
Seperate each bag into 2 equal groups, and set aside 1 of each
www.youtube.com/watch?v=UASzY5gcboY
Fitting Plastic Runners
SNAP!
SNAP!
SNAP!
SNAP!
Hx 1
Hx 1
3
Hx 1
2
1
Finished
front edge
Finished
front edge
L
R
4
5
Gx 2
2
1
2
1
Ax 12
6
7
8
3
Finished
front edge
Cx 4
Bx 4
3
3
2
Finished
front edge
Finished
front edge
9
10
32
x 2
4
Finished
front edge
Cx 4
Bx 4
11
12
4
2
x 2
5
Finished
front edge
Cx 4
Bx 4
Finished
front edge
13
14
5
x 2
1
x 6
15 Using 2 people place the unit onto the wall in the required position.
When it is in the correct position, mark the centre of the hole in
each of the unit’s 2 Brackets for drilling.
Mark the centre of
the 2 Brackets ready
for drilling
16
Carefully place the
Bedside unit onto the
wall by positioning the
Brackets over the Screws
Fit the key-hole part of
the Bracket over the
screw, making sure that
its protruding parts at the
top and bottom are
against the grooves in
the Bracket
Make sure the unit is
level, then drop the
key-hole part over the
Screw and tighten it up
Gx 2
Drill the holes for the Bedside Brackets
Drill into the mark-holes in the wall using an
appropriate drill-bit.
The screws and plugs are not supplied as they
need to be the correct type to suit your wall.
Note: Take care when drilling the wall that you
do not drill into any pipes, wires etc.
If in doubt, consult an expert.
See the next section for a guide to wall mounting and fixings
3cm
Leave the screws sticking out
from the wall by about 3cm
Important note:
Important: When drilling into walls always
check that there are no hidden wires or pipes etc.
If plastic wall plugs
are supplied with your
product:
- these are only suitable for
use in masonry walls.
If you are in any doubt about
the correct wall plugs for
your wall, seek professional
advice.
Failure of the product due to
using incorrect fixings is the
responsibility of the installer.
Make sure that the screws and wall plugs being used
are suitable for supporting your unit. Consult a qualified
tradesperson if you are unsure.
Hints:
1: General rule: Always use a larger screw and wall plug
if you are not sure.
2: Ensure you use the recommended drill bit to match the wall
plug and hole size.
3: Ensure you drill the hole horizontally, do not force the drill or
enlarge the hole.
4: Take extra care when drilling high walls, ceilings and ceramic
tiles. Ensure wall plugs are inserted beyond the thickness of
the ceramic tiles to avoid the tiles splitting or cracking.
5: Ensure wall plugs are well fitted and are a tight fit in the
drilled hole.
Types of walls You can use one of the following types of wall plug if your
walls are made of brick, breeze block, concrete, stone or wood.
Generally aerated blocks should not
be used to support heavy loads, use
a specialist fitting in this case. For light
loads, general purpose wall plugs can
be used.
For use with plasterboard partitions or
hollow wooden doors. For use with walls stuck with
plasterboard. The hammer fixing allows
it to be fixed to the wall rather than the
plasterboard. Always check the fixing
is secure to the retaining wall.
For use when attaching light loads on
to plasterboard partitions. For use when fitting or supporting
heavy loads such as shelving, wall
cabinets and coat racks.
For use with heavier loads such as TV
& HiFi speakers and satelite dishes etc.
No.1 “General Purpose” wall plug No.3 “Cavity Fixing” wall plug No.5 “Hammer Fixing” wall plug
No.2 “Plasterboard” wall plug No.4 “Cavity Fixing-Heavy Duty”
wall plug No.6 “Shield Anchor” wall plug
Heavy loads
A Guide to Wall Mounting & Fixings
Care &
Maintenance
Safety: Always check the fitting
and location to ensure your safety
in and around the home.
Fitting: From time to time check
the fitting to ensure the wall plugs
or screws do not become loose.
17 If required, follow the instructions below to alter the height of the Bedside unit.
Loosen the screw in
each Bracket and move
the unit up or down.
Drop the key-hole part
back down over the
screw and re-tighten it,
making sure it locates
into the grooves.
Slide the plastic cover
over the bracket
18
19
20
Drawer Assembly
www.youtube.com/watch?v=InNBV_uuMmo
Drawer Assembly
F171GY
Bag 2
Dx 4 Fx 8
A
F901
Ax 4 E
F639
x 6
F607
6
Ax 2
7
8
Dx 2
7
8
6
x 2
21
22
7
8
10
9
9
Fx 2
23
24
Fx 2
Ex 3
Make sure the Drawer Base panel is
inserted in all 4 grooves. You may
need to manoeuvre it slightly.
Important: Make sure that the
drawer assembly is square
before fitting the wedgefixes.
A
B
25
26
www.youtube.com/watch?v=UASzY5gcboY
Fitting Plastic Runners
Hx 2
27
28
ALR3763
Assembly is complete
Steps
2 - 26
Using the panels and fitting that were set aside in Step 1,
repeat Step 2 - 26 to assemble the other bedside
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20

GFW GFW 2 Wall Mounted Bedside Table Set User manual

Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI