Peerless DS-LEDA27-4x4 Installation guide

Category
Wall & ceiling mounts accessories
Type
Installation guide

This manual is also suitable for

12018-05-15 #:146-9026-4 (2019-08-15)
ENG
DS-LEDA27 Series
For Absen Acclaim
*Actual conguration may vary
22018-05-15 #:146-9026-4 (2019-08-15)
To properly tighten screws: Tighten until screw
head makes contact, then tighten another 1/2
turn. Do not overtighten screws.
1
2
+1/2
4
3
Symbols
ENG
WARNING
ENG
Do not overtighten screws.
ENG
Tools Needed for Assembly.
ENG
5/32"
(4mm)
ENG - This product is designed to be installed on plywood walls. Hardware is included for plywood installation.
Before installing make sure the supporting surface will support the combined load of the equipment and
hardware. Screws must be tightly secured. Do not overtighten screws or damage can occur and product may fail.
Never exceed the Maximum Load Capacity. Always use an assistant or mechanical lifting equipment to safely lift
and position equipment. This product is intended for indoor use only. Use of this product outdoors could lead to
product failure or personal injury. Be careful not to pinch ngers when operating the mount. For support please
call customer care at 1-800-865-2112.
WARNING
3/8"
(10mm)
3/8"
(10mm)
#
Skip to step.
ENG
32018-05-15 #:146-9026-4 (2019-08-15)
H
I
JM5 x 5mm
set screw
#14 x 2.5"
wood screw
M5 x 8mm
A1 A2 C
left column right column inside vertical
column kit
Parts List
Description
outside vertical column kit
A1 left column
A2 right column
spacer kit
B1 top vertical spacer
B2 bottom vertical spacer (not used)
B3 horizontal spacer
Cinside vertical column kit
Dtop horizontal extrusion asy
Ebottom horizontal extrusion asy
F extrusion connector
G 3mm allen wrench 2-tip t-handle
H M5 x 5mm set screw
I #14 x 2.5" wood screw
JM5 x 8mm socket button screw
K wall plate shim
Parts (Before beginning, make sure you have all parts shown below).
ENG
D
E
top horizontal
extrusion asy
bottom horizontal
extrusion asy
K
wall plate
shim
B3
horizontal
spacer
F
extrusion
connector
B2B1 bottom vertical
spacer
top vertical
spacer
G
3mm allen wrench
two-tip T-handle
42018-05-15 #:146-9026-4 (2019-08-15)
1
Refer to layout drawing included for your
specic model.
ENG
52018-05-15 #:146-9026-4 (2019-08-15)
2-1
Optional: If connecting two top horizontal extrusions,
rst remove inner hook-on brackets.
ENG
Remove and save hardware.
ENG
D
D
2-2
Use extrusion connectors to connect top horizontal
extrusions.
ENG
F (4)
G (4)
H (8)
D
D
G
G
62018-05-15 #:146-9026-4 (2019-08-15)
3-1
Optional: If connecting two bottom horizontal
extrusions, rst remove inner hook-on brackets
ENG
Remove and save hardware.
ENG
E
E
2-3
Replace one hook-on bracket in between connected
extrusions.
ENG
Use saved hardware.
ENG
D
D
G
G
72018-05-15 #:146-9026-4 (2019-08-15)
3-2
Use extrusion connectors to connect bottom
horizontal extrusions.
ENG
H (6)
F (3)
E
E
E
E
3-3
Replace one hook-on bracket in between connected
extrusions.
ENG
Use saved hardware.
ENG
G
G
82018-05-15 #:146-9026-4 (2019-08-15)
4-1
Use a laser level to keep mounting holes
level.
ENG
4
ENG - When installing Peerless wall mounts on a wood stud wall covered with plywood, verify that the wood
studs are a minimum of 2" x 4" nominal size and plywood is a minimum Grade BC, 1/2" (13 mm) thick. Plywood
may be covered by gypsum board (drywall) up to 5/8" thick.
WARNING
92018-05-15 #:146-9026-4 (2019-08-15)
4-2
Level top horizontal extrusion and mark
mounting holes on plywood (must be
minimum Grade BC, 1/2" (13mm) thick.)
ENG
D
3.94"
(100mm)
display tile
10 2018-05-15 #:146-9026-4 (2019-08-15)
4-3
Drill mounting holes into supporting surface
(2.5" (64mm) minimum depth required).
ENG
5/32"
(4mm)
2.5"
(64mm)
5/32"
(4mm)
4-4
Level extrusion. Install using wood screws
provided.
ENG
3/8"
(10mm)
Maximum 80 in. • lb (9 N.M.).
ENG
D
I (7)
11 2018-05-15 #:146-9026-4 (2019-08-15)
4-5
Secure vertical spacers to the wall ush with the
horizontal extrusion.
ENG
3/8"
(10mm)
Edges must be ush.
ENG
B1
I
D
B1 (2)
12 2018-05-15 #:146-9026-4 (2019-08-15)
4-6
Use third vertical spacer to align bottom
horizontal extrusion ush with vertical spacer,
then mark mounting holes on plywood (must be
minimum Grade BC, 1/2" (13mm) thick.)
ENG
56.19"
(143cm)
E
B1
Edges must be ush.
ENG
B1
E
13 2018-05-15 #:146-9026-4 (2019-08-15)
4-8
Use third vertical spacer to align bottom
horizontal extrusion ush with vertical
spacer, then install using wood screws
provided.
ENG
3/8"
(10mm)
Maximum 80 in. • lb (9 N.M.).
ENG
4-7
Drill mounting holes into supporting surface
(2.5" (64mm) minimum depth required).
ENG
5/32"
(4mm)
2.5"
(64mm)
5/32"
(4mm)
E
I (7)
14 2018-05-15 #:146-9026-4 (2019-08-15)
4-9
Remove vertical spacer.
ENG
3/8"
(10mm)
B1 (2)
15 2018-05-15 #:146-9026-4 (2019-08-15)
5-1
Hook on and secure outer vertical columns.
"L" and "R" markings designate left and right
column.
ENG
A1
A2
J (8)
Tighten hardware.
ENG
E
D
G
16 2018-05-15 #:146-9026-4 (2019-08-15)
5-2
Hook on and secure all inside vertical
columns.
ENG
C (4)
Tighten hardware.
ENG
J (16)
G
17 2018-05-15 #:146-9026-4 (2019-08-15)
6-1
Loosen hardware on vertical columns.
ENG G
18 2018-05-15 #:146-9026-4 (2019-08-15)
6-2
Tighten.
ENG
Tighten.
ENG
Plumb and level outer columns, then tighten
hardware. Tighten hardware on four corner wall
plates.
ENG G
19 2018-05-15 #:146-9026-4 (2019-08-15)
Tighten.
ENG
Loosen.
ENG
Optional leveling for bowed walls
ENG
Insert.
ENG
K
6-3
Tie a string between top slots on outer
columns in order to level the depth of each
vertical column.
ENG
Loosen, adjust, tighten.
ENG
G
20 2018-05-15 #:146-9026-4 (2019-08-15)
Tie a string between bottom slots on outer
columns in order to level the depth of each
vertical column.
ENG
Loosen, adjust, tighten.
ENG
6-4
Tighten.
ENG
Loosen.
ENG
Optional leveling for bowed walls
ENG
Insert.
ENG
K
G
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36

Peerless DS-LEDA27-4x4 Installation guide

Category
Wall & ceiling mounts accessories
Type
Installation guide
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI