Playnation Russet Racer Assembly Manual

190 Etowah Industrial Court

Canton, GA 30114

www.playnation.com

Russet Racer

Model: 702D

(BOXES: 701N-1, 701N-2, 702N,

Tire Swing Box & Slide Boxes)

Please inspect and inventory all parts immediately upon accepting delivery. Use the

inventory pages in the manual to make sure you have received all necessary parts.

The quickest method to get any parts that are missing or damaged is use our “Quick

Response Center” located at:

www.playnation.com/support

DO NOT RETURN THIS PRODUCT TO THE RETAILER OR CONTACT THE RETAILER DIRECTLY.

THE RETAILER DOES NOT STOCK COMPONENTS.

PLEASE RETAIN ALL INSTRUCTIONS FOR FUTURE REFERENCE. KEEP THEM IN A SAFE

PLACE WHERE YOU CAN REFER TO THEM AS NEEDED. CHECK FOR REVISED INSTRUC-

TIONS AT:

http://www.playnation.com/manuals.html

PLAYNATION WARRANTY 2015

MANUFACTURER'S LIMITED LIFETIME WARRANTY

PlayNation Play Systems, Inc. warrants its Lifetime™ series of swing sets to be free from defects in

workmanship and materials, under normal use and conditions, for the lifetime of the product for above

ground structural wood components and for two years for all other components (e.g., swings, hardware,

plastics, tarps, rope ladder, etc.) except PlayNation's Super Scoop Slides™ and Super Tube Spiral Slides™.

PlayNation warrants its Super Scoop Slides™ and Super Tube Spiral Slides™ to be free from defects in

workmanship and materials, under normal use and conditions, for the lifetime of the product.

PlayNation warrants its Regal™, Imperial™, and Empire™ series swing sets to be free from defects in

workmanship and materials, under normal use and conditions, for a period of 15 years for above ground

structural wood components and for two years for all other components (e.g., swings, hardware,

plastics, tarps, rope ladder, etc.).

PlayNation warrants all remaining products, including but not limited to its Free Standing Swing Set, Free

Standing Tire Swing, See-Saw, Children's Picnic Table with Umbrella, Play-Zee-Bo™ and spring riders to

be free from defects in workmanship and materials, under normal use and conditions, for a period of 1

year. All accessories purchased separate from those included with one of our swing set packages have a

one year limited warranty.

Cosmetic imperfections and natural tendencies of wood such as peeling, splintering, warping,

seasonal checking or cracking, knots or knot holes, etc. are normal characteristics of all outdoor

wooden play equipment and are not covered by this warranty. Checks or cracks in wood components

that do not affect the intended function of the part, piece or overall swing set are not covered under

this warranty.

Wood rot or decay that develops because the product was installed in an area with poor drainage is not

covered under this warranty. Lumber that has been damaged by wood boring bees, or conditions that

develop as a result of faulty or improper installation of the product, are not covered by this warranty.

Fading of stain, discoloration or mold on any wood part or accessory is not covered by this warranty.

Cracks in plastic components, surface rust on hardware and chips on powder coated materials are not

considered defects in material as long as they do not affect the functionality or structural integrity of the

part or component.

It is the owner's responsibility to maintain the swing set. This includes but is not limited to staining and

sealing the lumber as needed and regular inspection to be sure all hardware is tight. Instructions for

proper maintenance can be found on PlayNation's website. Imperfections or conditions that develop

because of a failure to properly maintain the swing set are not covered by this warranty.

PLAYNATION WARRANTY 2015

PlayNation will, at its discretion, replace any above ground part within the stated warranty period that is

defective in workmanship or materials. This decision is subject to verification of the defect, which, at

PlayNation's discretion, may be accomplished by submitting photographs or by delivery of the defective

part to PlayNation. PlayNation Play Systems, Inc. • 190 Etowah Industrial Ct. • Canton, GA 30114 •

770-704-9300 Monday to Friday 9AM-5PM EST. Any warranty claim must include proof of purchase,

including the date of purchase. In addition, within the first 30 days from the date of purchase,

PlayNation will replace any parts discovered to be missing from or damaged in the original packaging.

This warranty is valid only if the product is used for the purpose for which it was designed and installed

at a residential, single-family dwelling. This warranty is void if the product is used in a commercial,

institutional or multi-family setting. This warranty does not cover normal wear and tear or (a) products

that have been damaged by acts of God and/or nature, negligence, misuse or accident; (b) products

that have been modified or repaired by unauthorized persons; (c) the cost of labor; or (d) the cost of

shipping any replacement product or part.

PLAYNATION DISCLAIMS ALL OTHER REPRESENTATIONS AND WARRANTIES OF ANY KIND, EXPRESSED,

IMPLIED, STATUTORY OR OTHERWISE, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY

AND FITNESS FOR A PARTICULAR PURPOSE. PLAYNATION WILL NOT BE LIABLE FOR ANY INCIDENTAL OR

CONSEQUENTIAL DAMAGES. This warranty is non-transferable and does not extend to the owners of the

product subsequent to the original purchaser. Some states do not allow limitations on implied

warranties or exclusion of incidental or consequential damages, so these restrictions may not be

applicable to you. This warranty gives you specific legal rights. You may also have other rights which vary

from state to state.

IMPORTANT SAFETY GUIDELINES

This product is recommended for use by children ages 3-11. This product is intended for residential

use only and not intended for use in any public setting. A safety surface such as mulch or recycled

tire should be used under the play set to prevent injury from falls. Also a 6 foot safety zone should be

used around the entire play set.

As with any home project, good judgment and respect for power tools will greatly reduce the risk

of injury. PlayNation recommends you follow all tool manufacturers’ safety guidelines. Always wear

eye protection and safety gloves to prevent injury. In several phases of construction two people may

be required for lifting and securing of lumber. While the play set is being constructed, please keep

children off the equipment until the project is complete. Bolts and screw heads should be checked

regularly for tightness. The ground ladder, rope ladder, slide, swings and other areas where children

spend a majority of their playtime should be checked more frequently.

PlayNation shall not be liable for incidental, indirect or consequential damages or injuries that result

from the building and/or playing on our play sets. Adult supervision is recommended anytime a play

set is being used.

WEIGHT LIMITS FOR PLAYNATION PLAYSETS

• FORT PLATFORMS: 800 LBS. TOTAL WEIGHT

• SWING BELT: 225 LBS.

• GLIDER SWINGS: 70 LBS. PER CHILD. UP TO 140 LBS TOTAL WEIGHT.

• TRAPEZE: 125 LBS.

• FULL BUCKET SWING/ HALF BUCKET SWING: 50 LBS.

• HEAVY DUTY TODDLER BUCKET SWING: 85 LBS.

• INFANT SWING: 35 LBS.

• TIRE SWING: 125 LBS. TOTAL WEIGHT

• ROPE LADDER: 75 LBS.

• ROCK WALL: 150 LBS.

• CLIMBING RAMP: 150 LBS.

• MONKEY BARS: 175 LBS.

• ALL SLIDES: 150 LBS.

PlayNation recommends that the weight limits for all components must not be exceeded. Failure to

adhere to these and other safety guidelines could result in damage to the play set and injury to the

users.

THIS PAGE INTENTIONALLY LEFT BLANK

PlayNaon manufactures the

nest quality products that

are designed for outstanding

strength and durability. We

back our products with an

unparalleled warranty. In the

unlikely event that you will need

to contact us about covered

repairs, we must have a valid

Warranty Registraon on le.

Where did you buy this product?:

Store Store City Store StateDate of

Purchase

Name: Email:

Address:

Street City State Zip

Please select

your age?

18-30

31-40

41-50

51+

How old are

your children?

2-3

4-5

6-7

8+

How would

you rate the

quality of

this product?

Would you recommend this product to friends & family? Yes No

Your registraon informaon:

Comments:

Excellent

Average

Above Average

Below Average

Poor

3 EASY WAYS TO REGISTER

OPTION 1

OPTION 2

OPTION 3

Fax this completed form to:

(800) 880-3300 OR

Mail this completed form to:

PlayNaon Playsets

190 Etowah Industrial Court

Canton, GA 30114

Complete the online registraon form at:

hp://www.playnaon.com/register

Scan this QR Code

with your smart

phone to complete

the form using your

phone

WARRANTY REGISTRATION

- RUSSET RACER -

THIS PAGE INTENTIONALLY LEFT BLANK

IMPORTANT – PLEASE READ

Congratulations! You have just purchase one of the finest residential wooden swing sets available today. As

with any wooden product that spends its entire life outside, in varying elements, it is important to know what to

expect with your new swing set so that your family can enjoy it for many years.

As your swing set acclimates to its new environment, natural characteristics of the wood can show in the form

of checks, or “cracks” in the lumber. In almost all cases this is normal and it will not affect the structural

integrity of your play set and is not covered under warranty.

KEEPING YOUR PLAYSET LIKE NEW

MUST DO’s

The following owner responsibilities are crucial to the safety, integrity and aesthetic appeal of your

swing set and may affect the warranty if not adhered to.

WITHIN 60 DAYS

• Check and tighten Hex Bolts/T-nuts, Carriage Bolts/Lock-nuts, and Lag Screws within the first 60 days and

then twice annually – once before each season and then once during the season.

WITHIN 90 DAYS

• Apply a sealant or semi-transparent stain with sealant within the first 90 days of owning the swing set. If

applicable state laws allow, an oil based product will penetrate and protect the lumber better than a water

based product. Because climate conditions can vary drastically from region to region, we suggest asking the

product covering specialists at any number of specialty paint stores or home improvement centers for a

product that would work best for your local environment. ** TIP – while the set is new, take a small board from

your swing set to the store with you so they can color match the tint of the stain or sealant. Be sure to replace

the board when you get home.

SEASONAL REMINDERS

• If your area experiences regular snowfall, remove your fabric tarp/canopy to avoid stretching, sagging or

tearing of the material. Store it inside, folded up, and it will be as good as new when winter is over.

• If your area experiences extremely cold temperatures, remove swing belts and other pliable features to

prolong the lifespan of these play activities.

OTHER TIPS

• Spray swing hangers with Pam, Mazola or olive oil to stop squeaking; do not use petroleum based products

such as WD-40 or motor oil.

• To repel yellow jackets and wasps, use a cotton ball and dab interior wooden corners underneath the play set

deck with a liquid dish soap. Avoid using insecticides.

• To speed up the slide wipe the center of slide with wax paper every 2 - 3 weeks.

For additional safety and maintenance guidelines, please visit our website.

IMPORTANT DOCUMENTS

CUSTOMER MUST READ AND RETAIN

Please go to the following links and read important SAFETY information prior

to using your new play structure.

http://www.playnation.com/safety-and-maintenance.html

http://www.playnation.com/manuals.html (Click on your specific model)

http://www.playnation.com/warranty.html

NOTE: Your children’s safety is our #1 concern. Observing the following statements

and warnings reduces the likelihood of serious injury. Please review these safety rules

regularly with your children.

WARNING:

Children must NOT use this play set until it has been

completely assembled and inspected by an adult to

ensure it has been properly installed.

PlayNation Play Systems, Inc.

190 Etowah Industrial Court

Canton, GA. 30114

Model: 702D

(BOXES: 701-1, 701-2, 702, Tire

Swing Box & Slide Boxes)

REV: 2.3.2015

Safety Guidelines……………………………………….......……...........................Pages 3-6

Leveling Fort, General Information and Denitions............................................Pages 6-8

How to Install T-Nuts, Board Identication, Predrill Lag Screw Directions and

Swing Beam Loading........................................................................................Pages 9-13

Site Plan, Required Tool List and Kit Contents......………………………........Pages 14-15

Hardware, Lumber and Accessory Checklists……………………………….....Pages 16-27

Assembling the Ladder…………………………………..………...…..................... Steps 1-3

Assembling the Rock Wall.................................................................................. Steps 4-6

Framing the play set…………………………..…………………………..……...... Steps 7-15

Installing Rock Wall Boards……………………....……………….…………...…...... Step 16

Installing Tarp Boards and the Deck…………...…..……..……...….……......... Steps 17-23

Swing Beam Assembly……………………..……............................................. Steps 24-30

Tire Swing, Completing Rock Wall…….……………………..……................… Steps 31-33

Installing the Rope Ladder…...……………………….………........................... Steps 34-35

Mounting Slide………………………………………………….......................…........ Step 36

Securing Tarp……………...…………………………….…....................................... Step 37

Attaching Steering Wheel, Telescope and Safety Handles….....………......... Steps 38-40

Hanging Swings, Tic Tac Toe, Name Plate…………......…….…….……......... Steps 41-44

Flag Kits…………………………………………………………………….......………. Step 45

Ground Stakes……………....……………….................................................……... Step 46

PLEASE READ OWNER’S MANUAL CAREFULLY

BEFORE STARTING ASSEMBLY!

TABLE OF CONTENTS

2

Safety and Maintenance Tips for Your New Play Set:

NOTE: Your children’s safety is our #1 concern. Observing the

following statements and warnings reduces the likelihood of serious

or fatal injury. Please review these safety rules regularly with your

children.

• This play set is designed for the use of 4 occupants who have a combined weight not

exceeding 800 pounds on the elevated oor, 3 occupants who have a combined weight

of 425 pounds on the swing area, for a total Unit capacity of 7 occupants who have a

combined weight of 1225. (This weight does not include any picnic table area(s).)

• On-site adult supervision is required.

• Teach children not to walk close to, in front of, behind, or between moving swings or

other moving playground equipment.

• Teach children to sit in and never stand on swings

• Teach children not to twist the chains and ropes and not to loop them over the swing

beam, since this may reduce the strength of the chain or rope.

• Teach children not to jump from swings or other playground equipment in motion.

• Teach children not to push empty seats. The seat may hit them and cause serious

injury.

• Teach children to sit in the center of the swings with their full weight on the seats.

• Teach children not to use the equipment in a manner other than intended.

• Teach children to always go down slides feet rst. Never slide headrst.

• Teach children to look before they slide to make sure no one is at the bottom.

• Teach children to never run up a slide, as this increases their chances of falling.

• The parents should have the children dress appropriately with well-tting shoes. Loose

clothing such as scarves and ponchos should not be worn. Always take off, tie up or

tuck in cords and drawstrings on children’s clothing. These things can get caught on

playground equipment and strangle a child.

• Teach children not to climb when the equipment is wet.

• Teach children to never jump from a fort deck. They should always use the ladder,

ramp or slide.

• Teach children to never crawl or walk across the top of monkey bars or swing beam.

• Teach children to never crawl on top of a fort roof or on the outside of a tube slide.

• Verify that any suspended climbing ropes, chains, or cables are secured at both ends

and that they cannot be looped around an adult hand.

• Teach children not to attach items to the playground equipment that are not specically

designed for use with the equipment, such as, but not limited to, jump ropes, clothesline,

pet leashes, cables and chain as they may cause a strangulation hazard.

• Teach children to never wrap their legs around swing chain.

• Teach children to never slide down the swing chain.

• Teach children to remove their bike or other sports helmet before playing on the

playgound equipment.

• Teach children to NEVER look at the sun or other bright light through any accessory

such as but not limited to a telescope, periscope or binoculars.

WARNING: Children must NOT use this play set until it has been

completely assembled and inspected by an adult to insure it has been

properly installed and the swing beam legs are anchored.

3

Safety and Maintenance Tips for Your New Play Set:

(continued)

Playgrounds should be inspected on a regular basis. If any of the following conditions are noted,

they should be removed, corrected, or repaired immediately to prevent injuries.

• Hardware that is loose, worn or that has protrusions or projections.

• Exposed equipment footings.

• Scattered debris, litter, rocks, or tree roots.

• Splinters, large cracks, and decayed wood components.

• Deterioration and corrosion on structural components, which connect to the ground.

• Missing or damaged equipment components, such as handholds, guardrails, swing seats.

• Check all nuts and bolts twice monthly during the usage season and tighten as required.

(But not so tight that you crack the wood) We recommend you check the swing beam and

hardware often due to wood expansion and contraction. It is particularly important that this

procedure be followed at the beginning of each season.

• Remove plastic swing seats and take indoors or do not use when the temperature drops below

32°F. Reinstall swings and other swing equipment at the beginning of the usage season.

• Oil all metallic moving parts monthly during the usage period.

• Check all coverings for bolts and sharp edges twice monthly during usage season to be certain

they are in place. Replace when necessary. It is especially important to do this at the beginning

of each new season.

• Check swing seats, ropes, cables and chains monthly during usage season for evidence of

deterioration. Replacement should be made of any swing seat that has developed cracks in the

plastic seats. Ropes, cables and chains should be removed and replaced if excessive wear is

found. Contact us for warranted replacement parts.

• Swing chains, rings, ropes, etcetera should always be fastened to a rotating swing hanger.

NEVER attach a chain, ring, rope, etcetera to a stationary hanger such as but not limited to an

eye bolt. Severe wear could occur leading to an injury.

• For rusted areas on metallic members such as monkey bars, hand supports brackets, etc.;

sand and repaint, using a non lead-based paint meeting the requirements of Title 16 C.F.R. Part

1303. These requirements are available at: http://www.cpsc.gov/

• Inspect wood parts monthly. The grain of the wood sometimes will lift in the dry season

causing splinters to appear. Light sanding may be necessary to maintain a safe playing

environment. If you are treating your play set with stain regularly, it will help prevent severe

checking/splitting and other weather damage.

• Once or twice a year, depending on your climate conditions, you must apply some type of

protection (sealant) to the wood of your unit. Prior to the application of sealant, lightly sand any

“rough” spots on your set. Please note this is a requirement of your warranty.

• Creating and maintaining the play set on a level location is very important. As your children

play, your play set will slowly dig its way into the soil, and it is very important that it settles

evenly. Make sure the play set is level and true once each year or at the beginning of each play

season.

• Twice a month during the usage season rake the playground protective surfacing materials to

prevent compaction and maintain appropriate depths. Replace the protective surfacing materials

as required.

• Disposal Instructions: When the play set is no longer desired, it should be disassembled and

disposed of in such away that no unreasonable hazards will exist at the time the play set is

discarded.

4

Play Set Surfacing Recommendations:

Below are some of the recommendations that the U.S. Consumer Product Safety

Commission (CPSC) offers from its Handbook for Public Playground Safety. The guide

can be downloaded in full at www.cpsc.gov/cpscpub/pubs/325.pdf

1. Protective Surfacing - Since almost 60% of all injuries are caused by falls to the

ground, protective surfacing under and around all playground equipment is the most

critical safety factor on playgrounds.

Certain manufactured synthetic surfaces also are acceptable; however, test data on

shock absorbing performance should be requested from the manufacturer.

Asphalt and concrete are unacceptable. They do not have any shock absorbing

properties. Similarly, grass and turf should not be used. Their ability to absorb shock

during a fall can be reduced considerably through wear and environmental conditions.

Certain loose-ll surfacing materials are acceptable. Surfacing materials are acceptable,

such as the types and depths shown in the table.

Fall Heights and Materials

Type Of Material 6 in. depth 9 in. depth 12 in. depth

Double-Shredded bark mulch 6’ Fall Height 10’ Fall Height 11’ Fall Height

Wood Chips 6’ Fall Height 7’ Fall Height 12’ Fall Height

Fine Sand 5’ Fall Height 5’ Fall Height 9’ Fall Height

Shredded Tires* 10-12’ Fall Height N/A N/A

Fine Gravel 6’ Fall Height 7’ Fall Height 10’ Fall Height

*This data is from tests conducted by independent testing laboratories on a 6-inch depth of uncompressed shredded tire samples

produced by four manufacturers. The tests reported critical heights, which varied from 10 feet to greater than 12 feet. It is

recommended that persons seeking to install shredded tires as a protective surface request test data from the supplier showing the

critical height of the material when it was tested in accordance with ASTM F1292.

It should be recognized that all injuries due to falls cannot be prevented no matter what

surfacing material is used.

5

2. Fall Zones - A fall zone, covered with a protective surfacing material, is essential

under and around equipment where a child might fall. This area should be free of other

equipment and obstacles onto which a child might fall. Stationary climbing equipment

and slides should have a fall zone extending a Minimum of 6’ in all directions from the

perimeter of the equipment.

Swings should have a fall zone extending a minimum of 6’ from the outer edge of the

support structure on each side. The fall zone in front and back of the swing should

extend out a minimum distance of twice the height of the swing as measured from the

ground to the top of the swing support structure.

LEVELING YOUR FORT DURING ASSEMBLY

• Complete the steps which will be the basic frame of the fort. {i.e. four corner posts with

base (sand box boards) and deck supports}

• Position in the most level area chosen for the play set, keeping in mind the location

and size of the swing beam, ladder, slides, etc. that extend off the fort.

• Once the frame is in the nal position, check for vertical and horizontal levelness to

determine which side(s) will need to be dug into the ground to level the play set.

• With a shovel, score the ground around the outside edges of the sandbox boards on

the ‘high’ side of the fort. This is the area that will be dug in. Make sure to score deep

enough; the scored lines will be your digging template.

• Push the frame off and away from the scored area, far enough to dig and remove dirt

to reach the appropriate depth.

• Dig a channel along the scored line(s) for the base of the fort (corner post and

sandbox boards) to rest into. Dig the channel(s) to the same level depth. The bottom

of the channel(s) should be level to each other so your frame doesn’t teeter or rock

because the channel(s) are uneven.

• Once you have removed enough grass and dirt, slide/push the frame into the

channel(s). Place a level on the vertical and horizontal boards of the frame to determine

if enough soil, or too much, was removed.

• Repeat this process until the basic frame is plumb and level and in its nal position

before completing the rest of the assembly.

• Measure to make sure fort is square.

Important: if you require a channel depth of more than 6”, then we

recommend you have your play set area professionally graded before

completing assembly.

Example Play area:

= Area to be scored and

channeled for levelness

The diagonal measure-

ments should be the

same from corner post to

corner post. If not, adjust

corner posts so that the

distance is equal.

Side View of

Playset Frame

(Grade is the

Slanted Line)

6

General Info to Review Before Installation

• Depending on your experience, assembly of the playset can take as little as 6 hours

up to 24 hours, depending on size, after inventory of parts; therefore, we recommend

you set aside a full two days for assembly.

• Identify all of the parts for your play set. Empty each box and lay out boards so you

can see each part. Your instruction book will have detailed drawings that will make it

easy for you to recognize individual parts. Keep all hardware and metal parts separate

from wooden pieces.

• After everything is laid out, check carefully to ensure all parts are present. Make sure

there are no broken boards.

• Find an area to sort your hardware. It is best to open the hardware on a solid surface

so that you do not lose any pieces in the grass. This will save time and familiarize you

with all the different pieces in the hardware bag.

• Important note: Wood has some natural defects such as knots, surface cracks, etc…

We reject parts that are structurally defective. We use a high quality lumber in our

structures; however, you should inspect each part for splinters or rough spots and sand

them smooth to prevent injury.

• After familiarizing yourself with all of the components, read all instructions thoroughly.

Reading instructions after you have studied the parts will help you understand the

installation process, and help to eliminate unnecessary mistakes.

• Pay close attention to the diameter and length of each bolt and screw.

• Never tighten hardware completely at rst. It helps to have some adjustment for bolt

alignment while you are attaching parts together. After everything is square, tighten

each joint.

• After the main unit is assembled it is critical that the oor is level and square. If the

main frame is not level, the walls and oor will be out of square.

• After you complete installation, make sure every bolt, screw, and nut is tight, and every

board is secure. Wood will expand and contract with the seasons.

• Place the set on level ground, not less than 6 feet from any structure or obstruction

such as a fence, garage, house, overhanging branches, laundry lines, or electrical

wires.

7

Counter-Sunk Hole

Through Hole

This page is a list of denitions and explanations used throughout our

instructions to aid you in the assembly of your play set.

Offset Holes- Throughout the installation procedures we will refer to parts with offset

holes. This refers to the orientation of the holes on the board. An offset hole is one that

is closer to one side than it is the other or in other words, it is not centered on the board.

In the procedures you will be instructed to attach the boards with the holes offset up or

with the holes offset down. This refers to which side of the board the hole/holes should

be closer to. Offset holes up= hole/holes will be closer to the top of the board. Offset

holes down= hole/holes will be closer to the bottom of the board. Note: some parts do

not have offset holes, but instead the holes are on center. Therefore there will not be

any reference on how to offset these parts.

EXAMPLE OF OFFSET HOLES UP

EXAMPLE OF OFFSET HOLES DOWN

Counter-sunk holes - Many of the parts that will be used have counter-sunk holes. A

counter-sunk hole is one that surrounds one side of a through hole, but does not extend

through the wood it’s self. When using a counter-sunk hole the bolt will be inserted

through the through hole and either the head of the bolt and washer or nut and washer

will occupy the counter sunk hole.

Lag Screws- Lag screws are used in the construction of our play sets to enhance

the structural integrity of the unit. There will not be predrilled holes in the post for lag

screw installation. Lag screws are self-tapping, though if you are using a manual socket

wrench it may be advantageous to pre-drill a hole rst. Instructions for this are provided

on a separate page in the front of the manual. Be sure to tighten the lags completely

when driving them in by hand. Power tools such as a heavy duty impact driver or large

power drill should have enough torque to drive in the lag screws, but make sure not to

over tighten as this can cause the threads to “strip out” in the post.

8

Common Installation Practice Installing T-nuts

When installing T-nuts into the wood, use a smooth faced hammer to set the face of the

T-nut ush into the wood.

Insert the barrel of the T-nut into the

predrilled hole. Using a smooth faced

hammer, drive the T-nut until the face

of the T-nut is ush to the wood.

This picture shows the T-nut inserted

and installed ush to the wood.

This picture shows an end view of the T-nut

installed ush to the wood.

WARNING: DO NOT EMBED THE TOP

OF THE T-NUT INTO THE

FACE OF THE WOOD

Cross Section end view, you are looking at an X-ray view

of the post and T-nut. The barrel of the T-nut is in the

corner post the line is the face of the wood.

Corner Post

T-nut

Flush (Correct)

9

A

T-NUT

CORNER POST

BOARD YOU ARE

ATTACHING TO

CORNER POST.

WASHER

HEX HEAD BOLT

FRONT SIDE OF

CORNER POST

BACK SIDE OF

CORNER POST

T-NUT

FLANGE

IS HERE.

BOARD YOU

ARE ATTACHING

TO CORNER POST.

WASHER

HEX HEAD BOLT

CROSS SECTION VIEW

OF BOARD, CORNER

POST AND FASTENERS.

CORNER POST

DETAIL A

SCALE 2 : 1

FLANGE

SHAPED END

WITH TEETH

TEETH

BARREL

SHAPED

END GOES

INTO HOLE IN

CORNER POST.

T-NUT DETAILS

THREADS ON

INSIDE OF

BARREL .

HOW A T-NUT WORKS

THE FIRST STEP IN OUR ASSEMBLY INSTRUCTIONS IS TO INSERT T-NUTS INTO THE CORNER

POSTS. A T-NUT IS A FASTENER WHICH IS THREADED ON THE INSIDE AND IT FUNCTIONS

JUST LIKE A STANDARD HEX NUT. YOU INSERT THE T-NUTS INTO THE PREDRILLED HOLES IN

THE CORNER POSTS.

THE T-NUT HAS A BARREL SHAPED END WHICH GOES INTO THE HOLE IN THE CORNER POST.

THE T-NUT ALSO HAS AN FLANGE SHAPED END WITH TEETH. THE TEETH PENETRATE INTO THE

CORNER POST WOOD TO PREVENT THE T-NUT FROM SPINNING WHEN YOU TIGHTEN THE

HEX HEAD BOLT.

SHOWN BELOW YOU WILL SEE THE T-NUT IS HAMMERED INTO THE CORNER POST ON THE

BACK SIDE. THE BOARD IS BEING ATTACHED ON THE FRONT SIDE OF THE CORNER POST.

10

Page is loading ...

Playnation Russet Racer Assembly Manual

Related papers

Other documents