2. CTA
  3. PAD-PARAWPCL
PAD-PARAWPCL

CTA PAD-PARAWPCL Owner's manual

  • Hello! I've reviewed the instruction manual for the CTA Digital PAD-CHKWDC Premium Thin Profile Floor Stand with Digital Password Combination Security Enclosure. This document covers the assembly, cable routing, and security features of the product. I am ready to answer any questions you have about setting up this floor stand and using its features.
  • How do I assemble the floor stand base?
    How do I route the cable?
    How do I attach the enclosure to the VESA plate?
Premium Thin Profile Floor Stand w/
Digital Password Combination Security Enclosure
PAD-CHKWDC
INSTRUCTION - MANUAL
CONTENTS:
INSTALLATION:
1. Assembling floorstand base :
A
J
x1
M5 Allen Key
3. Attaching enclosure to VESA plate :
1A. Align the base plate (B) with the thin VESA profile (A) and screw in
the allen screws (D) with the allen key (J) turning it clockwise until secure-
ly tightened.
3A. Align enclosure (C) holes to VESA plate (A) holes. Turn in Screws
M5 X6 (D) above using provide tool (J) while holding hex nut (E) From
behind with fingers. Shown Above.
C
x1
E
x4
M5 Nut
x4
M5 Nut
M5 x 10
D
x4
M5 x 10
x4
B
x1
x1
x1
I
F
x4
M6
2. Cable routing :
G
I
4. Setting up the foam adapters :
4A. Identify the double sided adhesives (G). Peel away the backing
on both sides. Adhesive four of them behind the foam pieces (I) as
illustrated. They are to adhese the foam to the enclosure. Peel away
the back on the next four and place them on top of the foam pieces
as illustrated. These are to attach the foam to the tablets and ensure
security.
x1
H
x1
G
A
B
J
x4
D2C.Insert the cable through
the cutouts at floorstand head
and take it out in the cutout of
the back of the base.
2A. Plug one end of the tablet
cord into device, and route the
other end through hole in the
back as shown above.
2B. Cable route from enclosure
to the hole at the top of the body
as shown above.
J
C
A
D
888-733-4448
6A. When installing device into the enclosure, identify where the camera is.
Then simply remove and pop out the cover prior to mounting or setting up
tablet to properly expose camera.
6. Removing Enclosure Back Opening Covers :
7. Locking Enclosure :
7A. Once tablet is inserted, close the front cover securely.
7B. After, turn the digital lock 90ยบ degrees clockwise.
This will lock the tablet in place.
**See following page
for digital lock usage
and setup
8A. Identify the lock chart port on the bottom side as illustrated. Plug in provided
charging cable (H) from one end to another to properly charge digital lock.
8. Charge the lock :
H
**Tablet shown for
illustration only,
NOT INCLUDED.
**Tablet shown for
illustration only,
NOT INCLUDED.
9A. Tilt up/down for preferred angles as needed. Rotate left and right for
preferred orientation.
9. Adjusting angles & orientation :
**Tablet shown for
illustration only,
NOT INCLUDED.
**Tablet shown for
illustration only,
NOT INCLUDED.
C
I
C
I
5. Inserting Tablet into Enclosure :
5A. With the enclosure open, insert tablet into the foam adapters (I). Make
sure the adhesives have been placed ahead of time or tablet will fall out.
Plug your tablet into any cables/wires you have routed to the enclosure.
After tablet is secure, close the top and lock into place.
888-733-4448
/