Alpine WA01082 User manual

Brand: Alpine

Model: WA01082

Type: User manual

Alpine WA01082 is a forearm rollator designed to provide ambulatory assistance to those who need extra support. It features adjustable handrails and hand grips for customized comfort, and easy-to-use hand brakes for added safety. The rollator also includes a convenient seat that can be used for resting or taking a break on the go. With its sturdy construction and reliable performance, the Alpine WA01082 is an ideal mobility aid for those seeking independence and mobility.

USER MANUAL

PRODUCT CODE WA01082

FOREARM ROLLATOR

P. 1

PRODUCT CODE WA01082

NOTES

Check all parts for shipping damage. In case of shipping damage,

Do NOT use. Contact Dealer further instruction.

SAFETY SUMMARY

To ensure the safe operation of the Alpine Forearm Rollator, these

instructions MUST be followed:

General warning

• DO NOT install or use this equipment without rst reading and understanding

• the instructions. If you are unable to understand the Warnings, Cautions or

Instructions, contact a healthcare professional, dealer or technical personnel

before attempting to install this equipment–otherwise, injury or damage may

occur.

• User should always consult with their physician or therapist to determine

proper adjustment and usage.

• This equipment is NOT intended to be self-propelled while seated.

• A physical/occupational therapist should assist in the height adjustment of

the rollator for maximum support and correct brake activation, the xture of

the screw and the position of the quick release/assembly kits.

• Always ensure screws are fastened to the connector, so that the connector

can’t move when forced. Ensure the correct position of the quick release/

assembly kits, and they will not fall even with opposite force. Ensure all snap

buttons fully protrude through adjustment holes. Ensure the braking system

is eective when brake handle is locked or released.

• Care should be taken to ensure that ALL handles, height adjustment locks,

wheels, brakes or any other functional or moving parts are in good working

order before operation.

• All wheels MUST be in contact with the oor at ALL TIMES during use. This will

ensure the upright rollator is properly balanced. The brakes MUST be in the

locked position BEFORE using the seat.

P. 2

PRODUCT CODE WA01082

General warning

• When using the rollator in a stationary position, the hand brakes MUST be locked.

• DO NOT put your full weight on the linkage component nor use it as a handle

to carry the Walker. It is designed only for the purpose of connecting the two

armrest supports, neither for supporting the user nor carrying the Walker.

• DO NOT go up or down inclines greater than 15% or diagonally across inclines

greater than 5% when using as a traditional upright rollator with armrest

locked in horizontal position.

• DO NOT ride the rollator with all your weight on the armrests or lean

disproportionately on one of the armrests.

FAILURE TO FOLLOW THESE WARNINGS CAN LEAD TO INJURY.

Stability warning

• The Rollator can provide ambulatory assistance to an individual weighing up

to 300 lbs. (136kg), INCLUDING the weight of the contents in the bag.

• The Rollator bag has a weight limitation of 10 lbs. (4.5kg)

Folding or assembling warnings

• After unfolding or assembling rollator, make sure the seat tubing is securely

locked at both side slots, and the quick release/assembly kits are in their

correct position. All screws must be tightly locked without movement.

• DO NOT hang an additional weight on either side of the frame. This may cause

the rollator unbalanced when it is fully unfolded, resulting in injury or damage.

Installation warning

• Periodically check the rollator and attachments are properly and securely

locked in place BEFORE using.

P. 3

PRODUCT CODE WA01082

OPENING/FOLDING THE ROLLATOR

OPENING

Note: Refer to the FOLDING/ASSEMBLY WARNINGS in the SAFETY SUMMARY of this

instruction sheet.

Notes: For clearer display, the bag is not attached to the rollator.

1. Install the hand grip with brake & armrest component to the top of the side tube, and rotate

the black lever by 90 degrees and then lock it to the slot, as shown in Figure 1.

2. Open the rollator by pushing the side

frames outwards, as shown in Figure 2.

FIGURE 2

FIGURE 1

3. Lower the seat and push it down until both

seat rails are fully locked into the plastic

slots, as shown in Figure 3.

FIGURE 3

P. 4

PRODUCT CODE WA01082

OPENING/FOLDING THE ROLLATOR

4. Press the snap button and adjust it to the appropriate position. Make sure the snap button

protrudes through the hole on the linkage component, as shown in Figure 4.

FIGURE 4

5. Before using, test the rollator by grasping

the side frames and attempt to pushing

slightly inward with some force. The

rollator will remain locked in OPEN position

when the seat is completely open and

table, as shown in Figure 5.

FIGURE 5

P. 5

PRODUCT CODE WA01082

OPENING/FOLDING THE ROLLATOR

FOLDING

Note: For clearer display, the bag is not attached to the rollator.

1. Press the snap button and adjust it to the appropriate position. Make sure the snap button

protrudes through the hole on the linkage component, as shown in Figure 6.

2. Lift the band on the middle of the seat and push both the side frames inwards until the

rollator is completely closed, as shown in Figure 7.

FIGURE 6

FIGURE 7

P. 6

PRODUCT CODE WA01082

ADJUSTING HANDRAIL/ HAND GRIP/ BRAKE CABLES

Notes: Refer to the INSTALLATION WARNINGS in the SAFETY SUMMARY of this instruction

sheet.

1. Release the knob and adjust the height handrails upward or downward to the desired

height. Ensure both handrails are at the same height and the knob is locked after height

adjustment, as shown in gure 8.

2. Open the quick-release lever, adjust the hand grip to the appropriate angle and fasten the

lever. Ensure the quick-release lever is locked after angle adjustment, as shown in Figure 9.

FIGURE 8 FIGURE 9

USING HAND BRAKES

1. Pull the top portion of the brake handles UP towards

the hand grips, as shown in Figure 10.

FIGURE 10

LOCKING HAND BRAKES

1. Push DOWN on the bottom

portion of the brake handle

until an audible “click” is heard,

as shown in Figure 11.

FIGURE 11

PRODUCT CODE WA01082

CABLE ADJUSTER UNIT

If the tension of the brake handle is STILL too loose/tight, perform the following adjustments:

1. Figure Use ngers or a 10 mm wrench to turn the larger locking nut until loosened. Then

use ngers or pliers to turn barrel adjuster nut and try the brake. If this does not correct

the problem, repeat turning the barrel adjuster nut until the brake functions as expected.

Then tighten the locking nut until it presses tightly against the housing to prevent the

barrel adjuster nut from loosening. As shown in Figure 12.

2. Use ngers or a 10 mm wrench to turn the larger locking nut until loosened. Then use

ngers or pliers to turn barrel adjuster nut and try the brake. If this does not correct the

problem, repeat turning barrel adjuster until the brake functions as expected.

Then tighten the locking nut until it presses tightly against the xed plate to prevent the

barrel adjuster nut from loosening. As shown in Figure 13.

CARE AND MAINTENANCE

1. Ensure that ALL attaching hardware is

secured at ALL times.

2. Check the seat rails locked into the plastic

slots securely. If not, push down the seat

again.

3. Check the wheels are locked and installed

properly.

4. Make sure the quick release kit is locked.

5. Replace any broken, damaged or worn

items immediately.

CARE OF WHEELED ACCESSORIES

1. Clean wheels with warm water and

neutral cleanser. Dry with clean rag.

2. Lubricate with 3-in-l oil periodically if

wheels begin to squeak.

FIGURE 12 FIGURE 13

0333 015 5000 | CareCo UK Limited , Hubert Road, Brentwood, Essex, CM14 4JE

Alpine WA01082 User manual

Alpine WA01082 User manual

Alpine WA01082 User manual

Other documents