GB15
YOUR SAFETY AND THAT OF OTHERS IS PARAMOUNT
This manual and the appliance itself provide important safety warnings, to be read and observed at all
times.
All safety warnings give specific details of the potential risk present and indicate how to reduce risk of
injury, damage and electric shock resulting from improper use of the appliance. Carefully observe the
following instructions:
- The appliance must be disconnected from the power supply before carrying out any installation work.
- Installation and maintenance must be carried out by a qualified technician, in compliance with the
manufacturer’s instructions and local safety regulations. Do not repair or replace any part of the
appliance unless specifically stated in the user manual.
- Regulations require that the appliance is earthed.
- The power cable must be long enough for connecting the appliance, once fitted in its housing, to the
power supply socket.
- For installation to comply with current safety regulations, an all-pole disconnect switch with
minimum contact gap of 3 mm must be utilized.
- Do not use multiple plug adapters or extension leads.
- Do not pull the power supply cable in order to unplug the appliance.
- The electrical components must not be accessible to the user after installation.
- Do not touch the appliance with any wet part of the body and do not operate it when barefoot.
- This appliance is designed solely for use as a domestic appliance for cooking food. No other type of
use is permitted (e.g. heating rooms). The Manufacturer declines any liability for improper use or
incorrect setting of the controls.
- The appliance is not intended for use by persons (including children) with any physical, sensory or
mental impairment, or without experience and knowledge of the appliance, unless supervised or
previously instructed in its use by those responsible for their safety.
- The accessible parts of the appliance may become very hot during use. Young children should be
kept away from the appliance and supervised to ensure that they do not play with it.
- During and after use, do not touch the heating elements or interior surfaces of the appliance - risk of
burns. Do not allow the appliance to come into contact with cloths or other flammable materials until
all the components have cooled sufficiently.
- At the end of cooking, exercise caution when opening the appliance door, letting the hot air or steam
exit gradually before accessing the oven. When the appliance door is shut, hot air is vented from the
aperture above the control panel. Do not obstruct the vent apertures.
- Use oven gloves to remove pans and accessories, taking care not to touch the heating elements.
- Do not place flammable materials in or near the appliance: a fire may break out if the appliance is
inadvertently switched on.
- Do not heat or cook sealed jars or containers in the appliance. The pressure that builds up inside
might cause the jar to explode, damaging the appliance.
- Do not use containers made of synthetic materials.
- Overheated oils and fats catch fire easily. Always remain vigilant when cooking foods rich in fat and oil.
- Never leave the appliance unattended during food drying.
- If alcoholic beverages are added when roasting or cooking cakes and sweets (for example, rum, cognac,
wine), remember that alcohol evaporates at high temperatures. As a result, there is a risk that vapours
released by the alcohol may catch fire upon coming into contact with the electrical heating element.
IMPORTANT SAFETY INSTRUCTIONS
This is the danger symbol, pertaining to safety, which alerts users to potential risks to themselves
and others.
All safety warnings are preceded by the danger symbol and the following terms:
DANGER
Indicates a hazardous situation which, if not avoided, will cause serious injury.
WARNING
Indicates a hazardous situation which, if not avoided, could cause serious injury.
GB16
Scrapping of household appliances
- This appliance is manufactured with recyclable or reusable materials. Scrap the appliance in
accordance with local regulations on waste disposal. Before scrapping, cut off the power cords so that
the appliances cannot be connected to the mains.
- For further information on the treatment, recovery and recycling of household electrical appliances,
contact your competent local authority, the collection service for household waste or the store where
you purchased the appliance.
Unpack the oven and make sure that the oven has not been damaged during transport and that the oven
door closes properly. In the event of problems, contact the dealer or your nearest After-sales Service. To
prevent any damage, only remove the oven from its polystyrene foam base at the time of installation.
PREPARING THE HOUSING UNIT
• Kitchen units in contact with the oven must be heat resistant (min 90°C).
• Carry out all cabinet cutting work before fitting the oven in the housing and carefully remove all
wood chips and sawdust.
• After installation, the bottom of the oven must no longer be accessible.
• For correct appliance operation, do not obstruct the minimum gap between the worktop and the
upper edge of the oven.
ELECTRICAL CONNECTION
Make sure the power voltage specified on the appliance dataplate is the same as the mains voltage. The
dataplate is on the front edge of the oven (visible when the door is open).
• Power cable replacement (type H05 RR-F 3 x 1.5 mm
2
) must be carried out by a qualified electrician.
Contact an authorized service centre.
GENERAL RECOMMENDATIONS
Before use:
- Remove cardboard protection pieces, protective film and adhesive labels from accessories.
- Remove the accessories from the oven and heat it 200°C for about an hour to eliminate the smell of
the protective grease and insulating materials.
During use:
- Do not place heavy objects on the door as they could damage it.
- Do not cling to the door or hang anything from the handle.
- Do not cover the inside of the oven with aluminium foil.
- Do not pour water into the inside of a hot oven; this could damage the enamel coating.
- Never drag pots or pans across the bottom of the oven as this could damage the enamel coating.
- Make sure that the electrical cables of other appliances do not touch hot parts of the oven or become
trapped in the door.
- Never expose the oven to atmospheric agents.
Disposal of packaging materials
The packing material is 100% recyclable and is marked with the recycle symbol ( ). The various parts of
the packing must therefore be disposed of responsibly and in full compliance with local authority
regulations governing waste disposal.
Scrapping the product
- This appliance is marked in compliance with European Directive 2002/96/EC, Waste Electrical and
Electronic Equipment (WEEE).
- By ensuring this product is disposed of correctly, you will help prevent potential negative
consequences for the environment and human health, which could otherwise be caused by
inappropriate waste handling of this product.
- The symbol on the product or on the accompanying documentation indicates that it should not be
treated as domestic waste but must be taken to an appropriate collection centre for the recycling of
electrical and electronic equipment.
INSTALLATION
SAFEGUARDING THE ENVIRONMENT
GB17
Energy saving
- Only pre-heat the oven if specified in the cooking table or your recipe.
- Use dark lacquered or enamelled baking moulds as they absorb heat far better.
- Switch the oven off 10/15 minutes before the set cooking time. Food requiring prolonged cooking will
continue to cook even once the oven is switched off.
- oven, which is intended to come into contact with foodstuffs, complies with European Regulation
( ) n. 1935/2004 and has been designed, manufactured and sold in conformity with the safety
requirements of the “Low Voltage” directive 2006/95/CE (which replaces 73/23/CEE and subsequent
amendments), the protection requirements of “EMC” 2004/108/CE.
Oven not working:
• Check for the presence of mains electrical power and if the oven is connected to the electrical supply.
• Turn off the oven and restart it to see if the fault persists.
Before calling the After-Sales Service:
1. See if you can solve the problem yourself with the help of the suggestions given in the
“Troubleshooting guide”.
2. Switch the appliance off and then on again it to see if the problem has been eliminated.
If the fault persists after the above checks, contact the nearest After-sales Service.
Always specify:
• a brief description of the fault;
• the type and exact model of the oven;
• the service number (number after the word Service on the rating plate), located on the right hand
edge of the oven cavity (visible when the oven door is open). The service number is also indicated on
the guarantee booklet;
• your full address;
• your telephone number.
If any repairs are required, contact an authorised After-sales Technical Service (to guarantee the use of
original spare parts and correct repair).
Exterior of the oven
IMPORTANT: do not use corrosive or abrasive detergents. If any of these products accidentally
comes into contact with the appliance, clean immediately with a damp cloth.
• Clean the surfaces with a damp cloth. If it is very dirty, add a few drops of washing up detergent to the
water. Finish off with a dry cloth.
DECLARATION OF CONFORMITY
TROUBLESHOOTING GUIDE
AFTER-SALES SERVICE
CLEANING
WARNING
- Do not use steam cleaners.
- Only clean the oven when it is cool to the touch.
- Disconnect the appliance from the power supply.
GB18
Oven interior
IMPORTANT: do not use abrasive sponges or metallic scrapers or scourers. Over time, these can ruin
enamelled surfaces and the oven door glass.
• After every use, allow the oven to cool then clean it preferably while it is still warm in order to remove
built-up dirt and stains caused by food residues (e.g. food with a high sugar content.
• Use proprietary oven detergents and follow the manufacturer’s instructions to the letter.
• Clean the door glass with a suitable liquid detergent. The oven door can be removed to facilitate
cleaning (see MAINTENANCE).
• The top heating element of the grill (see MAINTENANCE) can be lowered (some models only) to clean
the roof of the oven.
N.B: during prolonged cooking of foods with a high water content (e.g. pizza, vegetables, etc.)
condensation may form on the inside of the door and around the seal. When the oven is cold, dry the
inside of the door with a cloth or sponge.
Accessories:
• Soak the accessories in water with washing up detergent immediately after use, handling them with
oven gloves if still hot.
• Food residues can be easily removed using a brush or sponge.
Cleaning the rear wall and catalytic side panels of the oven (if present):
IMPORTANT: do not use corrosive or abrasive detergents, coarse brushes, pot scourers or oven
sprays which could damage the catalytic surface and ruin its self-cleaning properties.
• Operate the oven empty with the fan-assisted function at 200°C for about one hour.
• Next, leave the appliance to cool down before removing any food residue with a sponge.
REMOVING THE DOOR
To remove the door:
1. Open the door fully.
2. Lift the catches and push them forwards as far as they will go (Fig. 1).
3. Close the door as far as it will go (A), lift it up (B) and turn it (C) until it is released (D) (Fig. 2).
To refit the door:
1. Insert the hinges in their seats.
2. Open the door fully.
3. Lower the two catches.
4. Close the door.
MAINTENANCE
WARNING
- Use protective gloves.
- Ensure the oven is cold before carrying out the following operations.
- Disconnect the appliance from the power supply.
Fig. 1 Fig. 2
GB19
MOVING THE TOP HEATING ELEMENT (SOME MODELS ONLY)
1. Remove the side accessory holder grilles.
2. Pull the heating element out a little (Fig. 3) and lower it (Fig. 4).
3. To reposition the heating element, lift it up, pulling it slightly towards you, making sure it comes to
rest on the lateral supports.
REPLACING THE OVEN LAMP
To replace the rear lamp (if present):
1. Disconnect the oven from the power supply.
2. Unscrew the lamp cover (Fig. 5), replace the lamp (see note for lamp type) and screw the lamp cover
back on.
3. Reconnect the oven to the power supply.
To replace the side lamp (if present):
1. Disconnect the oven from the power supply.
2. Remove the side accessory holder grilles, if present.
3. Use a screwdriver to prise off the lamp cover.
4. Replace the lamp (see note for lamp type).
5. Refit the lamp cover, pushing it on firmly until it clicks into place.
6. Refit the side accessory holder grilles.
7. Reconnect the oven to the power supply.
N.B:
- Only use 25-40W/230V type E-14, T300°C incandescent lamps, or 20-40W/230V type G9, T300°C
halogen lamps.
- Lamps are available from our After-sales Service.
IMPORTANT:
- If using halogen lamps, do not handle with bare hands since fingerprints can damage them.
- Do not use the oven until the lamp cover has been repositioned.
Fig. 3 Fig. 4
Fig. 5 Fig. 6 Fig. 7 Fig. 8
GB20
FOR ELECTRICAL CONNECTION, SEE THE PARAGRAPH ON INSTALLATION
1. Control panel
2. Upper heating element/grill
3. Cooling fan (not visible)
4. Dataplate (not to be removed)
5. Lamp
6. Fan
7. Turnspit (if present)
8. Lower heating element (not visible)
9. Door
10. Position of shelves (the number of shelves is indicated on the front of the oven)
11. Rear wall
N.B.:
- During cooking, the cooling fan may switch on at intervals in order to minimise energy consumption.
- At the end of cooking, after the oven has been switched off, the cooling fan may continue to run for a
while.
ACCESSORIES SUPPLIED
A. WIRE SHELF: the wire shelf can be used to grill food or as a support for pans, cake tins and other
ovenproof cooking receptacles.
B. BAKING TRAY: for cooking all bread and pastry products, but also roasts, fish en papillotte, etc.
C. DRIP TRAY: the drip tray is designed to be positioned under the wire shelf in order to collect fat or as
an oven tray for cooking meat, fish, vegetables, focaccia, etc.
ACCESSORIES NOT SUPPLIED
Other accessories can be purchased separately from the After-sales Service.
INSTRUCTIONS FOR OVEN USE
Fig. A Fig. B Fig. C
GB21
INSERTING WIRE SHELVES AND OTHER ACCESSORIES IN THE OVEN
The wire shelf and other accessories are provided with a locking mechanism to prevent their unintentional
removal.
1. Insert the wire shelf horizontally, with the raised part “A” upwards (Fig. 1).
2. Angle the wire shelf when it reaches the locking position “B” (Fig. 2).
3. Return the wire shelf to the horizontal position and push it in fully to “C” (Fig. 3).
4. To remove the wire shelf proceed in reverse order.
The other accessories, like the drip tray and baking tray, are inserted in exactly the same way. The
protrusion on the flat surface enables the accessories to lock in place.
CONTROL PANEL DESCRIPTION
1. FUNCTION SELECTOR KNOB: on/off and function selector knob
2. THERMOSTAT KNOB: selecting the temperature
3. CONTROL KNOB FOR FRONT LEFT HOTPLATE 0 1 ... 10 *
4. CONTROL KNOB FOR REAR LEFT HOTPLATE 0 1 ... 10 *
5. CONTROL KNOB FOR REAR RIGHT HOTPLATE 0 1 ... 10 *
6. CONTROL KNOB FOR FRONT RIGHT HOTPLATE 0 1 ... 10 *
N.B.:the knobs are retractable. Press the knobs in the middle and they pop up.
7. ELECTRONIC PROGRAMMER
8. THERMOSTAT LED
* The multizone function can only be switched on for the double and triple hotplates of the cooktop.
(See cooktop functions table).
OVEN OPERATION
• Turn the selector knob to the required function.
The oven light switches on.
• Turn the thermostat knob clockwise to the required temperature.
The thermostat led lights up, switching off again when the oven reaches the selected temperature.
At the end of cooking, turn the knobs to “0”.
COOKTOP OPERATION
The oven control panel features 4 adjustable knobs for cooktop operation. The cooktop control knobs are
marked with a numerical scale corresponding to different power settings, and a series of function symbols.
• Turn the control knob of the relevant hotplate clockwise to the desired power setting (see the
instructions supplied with the cooktop).
Fig. 1
Fig. 2 Fig. 3
3 5 6 84 1 7 2
GB22
USING THE ELECTRONIC PROGRAMMER
Using the oven for the first time
Setting the time of day and the tone of the acoustic signal.
Upon connection of the oven to the mains power supply, AUTO and 0.00 flash on the display. To set the
time of day, press buttons - and + at the same time: the two central dots flash. Set the time of day using the
buttons + and -. Having selected the desired value, press the middle button. The display shows “ton 1”. To
select the desired tone, press button –. Having selected the preferred tone, press the middle button. To
change the time of day, proceed as described above.
Setting the timer
To set the timer, long-press the middle button: the display shows 0.00 and the bell symbol flashes. Set the
timer using the button + (the maximum programmable value is 23 hours and 59 minutes). The countdown
begins after a few seconds. The display shows the time of day and the bell remains lit, confirming the timer
has been set. To view the countdown and change it if necessary, press the middle button again.
Setting cooking time
After selecting the cooking mode and temperature using the knobs, press the middle button: the display
shows 0.00 and the bell symbol flashes. Press the middle button again: on the display and 0.00 appear
in sequence and AUTO flashes. Set cooking time using the buttons + and - (the maximum programmable
value is 10 hours). After a few seconds the display shows the time of day and AUTO remains lit, confirming
the setting. To view the remaining cooking time and change it if necessary, press the middle button for 2
seconds and then press it again a second time. At the end of the set time, the symbol switches off, the
alarm sounds and AUTO flashes on the display. Press any button to deactivate the alarm. Return the
functions and temperature knob to zero and press the middle button for two seconds to end cooking.
Delaying cooking end time
After selecting cooking time, press the middle button: the display shows , cooking end time and AUTO
flashing in sequence. Press the button + to view the desired cooking end time (cooking can be delayed by
a maximum of 23 hours and 59 minutes). After a few seconds the display shows the time of day, the symbol
switches off and AUTO remains lit, confirming the setting. To view cooking end time and change it if
necessary, press the middle button and then press it again twice. At the end of the countdown, the symbol
lights up and the oven proceeds with the selected cooking mode.
1. Button - : to decrease the value shown on the display
2. Button : for selecting the various settings:
a. Timer
b. Cooking time
c. Cooking end time setting
3. Button + : to increase the value shown on the display
A. The symbol
indicates that the timer function is in operation
B. The AUTO symbol confirms the setting has been made
A
U
T
O
2 31
A
B
GB23
COOKTOP FUNCTIONS TABLE (depending on model)
COOKTOP CONTROL KNOBS
GENTLE HEAT
To allow dough to rise, to soften butter taken from the fridge, to keep baby
bottles or food warm, also for making yoghurt, melting chocolate, etc.
This function is only available when the residual heat indicator is on. For this
function, make sure the residual heat indicator of the desired hotplate is on.
Turn the knob to . To deselect the function, change the position of the
knob.
HEAT
MAINTENANCE
To maintain a constant temperature of 60° until the end of cooking. To select
this function, turn the knob to .
FAST BOIL
This function is used to bring water to the boil rapidly and remains on for a
preset time. At the end of the preset time, the cooktop automatically returns
to the maximum power setting. This function can be selected even during
cooking. Caution: before selecting this function, make sure the pot is
positioned on the selected hotplate in order to avoid any damage to the
cooktop surface. The stated performance values for this function are those
guaranteed for all glass ceramic cooktops. For this function, place the pot on
the selected hotplate and turn the knob to . To deselect, change the
position of the knob.
MULTIZONE
The multizone symbol on the knobs is activated only for the hotplates of the
cooktop provided with double or triple zone. These functions extend the
heating area of the cooktop to allow the use of large, oval or rectangular
pots. To switch on the double zone (if present), turn the knob to the “double
zone” symbol and then back anticlockwise to select the desired power level.
To switch on the triple zone (if present), turn the knob to the “triple zone”
symbol and then back anticlockwise to select the desired power level. The
residual heat indicator remains on to indicate that the cooktop is switched
on. Switch off by turning the knob to “0”.
GB24
OVEN FUNCTION DESCRIPTION TABLE
FUNCTIONS KNOB
OFF To stop cooking and switch off the oven.
LAMP To switch the oven light on/off.
CONVENTIONAL
To cook any kind of dish on one shelf only. Use the 2nd shelf. Preheat the
oven to the required temperature. The thermostat led turns off when the
oven is ready and food can be placed in it.
CONVECTION
BAKE
For baking cakes with liquid filling (sweet or savoury) on a single shelf. This
function can also be used for cooking on two shelves. Switch the position of
the dishes to cook food more evenly. Use the 2nd shelf to cook on one shelf
only, and the 2nd and 4th to cook on two shelves. Preheat the oven before
cooking.
GRILL
To grill steak, kebabs and sausages; to cook vegetables au gratin and toast
bread. Place food on the 4th shelf. When grilling meat, use the drip tray to
collect the cooking juices. Position it on the 3rd shelf, adding approx. half a
litre of water. Preheat the oven for 3-5 min. During cooking the oven door
must remain closed.
TURBO GRILL
To roast large joints of meat (legs, roast beef, chickens). Position the food on
the middle shelves. Use the drip tray to collect the cooking juices. Position it
on the 1st/2nd shelf, adding approx. half a litre of water. It is advisable to turn
the meat over during cooking for more even browning. The oven does not
have to be preheated. During cooking the oven door must remain closed.
DEFROST
To speed up defrosting of food. Place food on the middle shelf. Leave food in
its packaging in order to prevent it from drying out on the outside.
GB25
COOKING TABLE
Recipe
Function Preheating Shelf (from
bottom)
Temp.
(°C)
Time
(min)
Accessories and notes
Leavened cakes
Yes 2 150-175 35-90 Cake tin on wire shelf
Yes 2-4 150-170 30-90
Shelf 4: cake tin on wire shelf
(switch levels halfway
through cooking)
Shelf 2: cake tin on wire shelf
Filled pies
(cheesecake,
strudel, apple pie)
Yes 2 150-190 30-85
Drip tray/ baking tray or cake
tin on wire shelf
Yes 2-4 150-190 35-90
Shelf 4: cake tin on wire shelf
(switch levels halfway
through cooking)
Shelf 2: cake tin on wire shelf
Biscuits / Tartlets
Yes 2 160-175 20-45 Drip tray / baking tray
Yes 2-4 160-170 20-45
Shelf 4: wire shelf (switch
levels halfway through
cooking)
Shelf 2: drip tray / baking tray
Choux buns
Yes 2 175-200 30-40 Drip tray / baking tray
Yes 2-4 170-190 35-45
Shelf 4: oven tray on wire
shelf (switch levels halfway
through cooking)
Shelf 2: drip tray / baking tray
Meringues
Yes 2 100 110-150 Drip tray / baking tray
Yes 2-4 100 130-150
Shelf 4: oven tray on wire
shelf (switch levels halfway
through cooking)
Shelf 2: drip tray / baking tray
Bread / Pizza /
Focaccia
Yes 2 225-250 12-50 Drip tray / baking tray
Yes 2-4 225-250 20-45
Shelf 4: oven tray on wire
shelf (switch levels halfway
through cooking)
Shelf 2: drip tray / baking tray
Frozen pizza
Yes 2 250 10-15
Drip tray / baking tray or wire
shelf
Yes 2-4 250 10-20
Shelf 4: oven tray on wire
shelf (switch levels halfway
through cooking)
Shelf 2: drip tray / baking tray
Savoury pies
(vegetable pie,
quiche)
Yes 2 175-200 45-55 Cake tin on wire shelf
Yes 2-4 175-190 45-60
Shelf 4: cake tin on wire shelf
(switch levels halfway
through cooking)
Shelf 2: cake tin on wire shelf
GB26
Vols-au-vent / Puff
pastry crackers
Yes 2 175-200 20-30 Drip tray / baking tray
Yes 2-4 175-200 20-40
Shelf 4: oven tray on wire
shelf (switch levels halfway
through cooking)
Shelf 2: drip tray / baking tray
Lasagne / Baked
pasta / Cannelloni /
Flans
Yes 2 200 45-55 Oven tray on wire shelf
Lamb / Veal / Beef /
Pork 1 Kg
Yes 2 200 80-110
Drip tray or oven tray on wire
shelf
Chicken / Rabbit /
Duck 1 Kg
Yes 2 200 50-100
Drip tray or oven tray on wire
shelf
Turkey / Goose
3 Kg
Yes 1/2 200 80-130
Drip tray or oven tray on wire
shelf
Baked fish / en
papillote (fillet,
whole)
Yes 2 175-200 40-60
Drip tray or oven tray on wire
shelf
Stuffed vegetables
(tomatoes,
courgettes,
aubergines)
Yes 2 175-200 50-60 Oven tray on wire shelf
Toast Yes 4 200 3-5 grill
Fish fillets / steaks Yes 4 200 20-30
Shelf 4: wire shelf (turn food
halfway through cooking)
Shelf 3: drip tray with water
Sausages / Kebabs
/ Spare ribs /
Hamburgers
Yes 4 200 30-40
Shelf 4: wire shelf (turn food
halfway through cooking)
Shelf 3: drip tray with water
Roast chicken
1-1.3 Kg
- 2 200 55-70
Shelf 2: wire shelf (turn food
two thirds of the way
through cooking if
necessary)
Shelf 1: drip tray with water
Roast Beef rare
1 Kg
- 2 200 35-45
Oven tray on wire shelf (turn
food two thirds of the way
through cooking if
necessary)
Leg of lamb /
Shanks
- 2 200 60-90
Drip tray or oven tray on wire
shelf (turn food two thirds of
the way through cooking if
necessary)
Roast potatoes - 2 200 45-55
Drip-tray / baking tray (if
necessary, turn food two
thirds of the way through
cooking)
Vegetable gratin - 2 200 20-30 Oven tray on wire shelf
Recipe
Function Preheating Shelf (from
bottom)
Temp.
(°C)
Time
(min)
Accessories and notes
GB27
Lasagna & Meat Yes 2-4 200 50-100
Shelf 4: oven tray on wire
shelf (switch levels two thirds
of the way through cooking
if necessary)
Shelf 2: drip tray or oven tray
on wire shelf
Meat & Potatoes Yes 2-4 200 45-100
Shelf 4: oven tray on wire
shelf (switch levels two thirds
of the way through cooking
if necessary)
Shelf 2: drip tray or oven tray
on wire shelf
Fish & Vegetables Yes 2-4 175 30-50
Shelf 4: oven tray on wire
shelf
Shelf 2: drip tray or oven tray
on wire shelf
Recipe
Function Preheating Shelf (from
bottom)
Temp.
(°C)
Time
(min)
Accessories and notes
GB28
How to read the cooking table
The table indicates the best function to use for any given food, to be cooked on one or more shelves at the
same time. Cooking times start from the moment food is placed in the oven, excluding pre-heating (where
required). Cooking temperatures and times are purely for guidance and will depend on the amount of food
and type of accessory used. Use the lowest recommended values to begin with and, if the food is not
cooked enough, then move on to higher values. Use the accessories supplied and preferably dark coloured
metal cake tins and oven trays. You can also use pans and accessories in pyrex or stoneware, but bear in
mind that cooking times will be slightly longer. To obtain best results, carefully follow the advice given in
the cooking table for the choice of accessories (supplied) to be placed on the various shelves.
Cooking different foods at the same time
Using the “CONVECTION BAKE” function, you can cook different foods which require the same cooking
temperature at the same time (for example: fish and vegetables), using different shelves. Remove the food
which requires less cooking time and leave food which requires longer cooking time in the oven.
Desserts
- Cook delicate desserts with the conventional function on one shelf only. Use dark coloured metal
cake tins and always position them on the wire shelf supplied. To cook on more than one shelf, select
the forced air function and stagger the position of the cake tins on the shelves, aiding optimum
circulation of the hot air.
- To check whether a raising cake is cooked, insert a wooden toothpick into the centre of the cake. If
the toothpick comes out clean, the cake is ready.
- If using non-stick cake tins, do not butter the edges as the cake may not rise evenly around the edges.
- If the cake “sinks” during cooking, set a lower temperature the next time, perhaps reducing the
amount of liquid in the mixture and mixing more gently.
- For sweets with moist fillings (cheesecake or fruit pies) use the “CONVECTION BAKE” function. If the
base of the cake is soggy, lower the shelf and sprinkle the bottom of the cake with breadcrumbs or
biscuit crumbs before adding the filling.
Meat
- Use any kind of oven tray or pyrex dish suited to the size of the piece of meat being cooked. For roast
joints, it is best to add some stock to the bottom of the pan, basting the meat during cooking for
added flavour. When the roast is ready, let it rest in the oven for another 10-15 minutes, or wrap it in
aluminium foil.
- When you want to grill meat, choose cuts with an even thickness all over in order to achieve uniform
cooking results. Very thick pieces of meat require longer cooking times. To prevent the meat from
burning on the outside, lower the position of the wire shelf, keeping the food farther away from the
grill. Turn the meat two thirds of the way through cooking.
To collect the cooking juices it is advisable to place a drip-tray with half a litre of water directly under the
grill on which the meat is placed. Top-up when necessary.
Turnspit (only in some models)
Use this accessory to evenly roast large pieces of meat and poultry. Place the meat on the turnspit rod, tying
it with string if chicken, and check that it is secure before inserting the rod in the seat located on the front
wall of the oven and resting it on the respective support. To prevent smoke and to collect cooking juices,
it is advisable to place a drip-tray with half a litre of water on the first level. The rod has a plastic handle
which must be removed before starting to cook, and used at the end of cooking to avoid burns when
taking the food out of the oven.
Pizza
Lightly grease the trays to ensure the pizza has a crispy base. Scatter the mozzarella over the pizza two
thirds of the way through cooking.
RECOMMENDED USE AND TIPS
Bauknecht, Polar and Ignis are registered trademarks of the Whirlpool group of companies.
Printed in Italy
09/2010
5019 400 00257
DE GB
Copyright Whirlpool Europe s.r.l. 2010. All rights reserved
http://www.bauknecht.eu
/