Friedrich WS10D30A User manual

WM-ServMan (4-10)

WallMaster

®

R-410A Models

2010

Service Manual

115-Volt: WS08C10A, WS10C10A, WS12C10A

230-Volt: WS10C30A, WS13C30A, WS15C30A

Cool Only

115-Volt: WE10C33A, WE13C33A, WE15C33A

Cool with Electric Heat

230-Volt: WY09C33A, WY12C33A

Heat Pump with Electric Heat Back Up

Wa

l

M

a

s

t

e

r

Money

Fa n

Timer Operation

Set Hr.

Stop

Start

Temperature

Fa n

Cool

Po we r

Cooler

Warmer

Only Speed Saver

®

Heat

Air Conditioners and Heat Pumps

Thru-the-wall

Table Of Contents

Important Safety Information ....................................................................................................................2-4

Introduction ..................................................................................................................................................4

WallMaster Model Number Code and Serial Number Identication ............................................................5

Performance Data / Sleeve and Chassis Dimensions .................................................................................6

Electrical Data ..............................................................................................................................................7

How to Operate the Electronic WallMaster Room Air Conditioner ...........................................................8-9

Remote Control .........................................................................................................................................10

Electronic Control: Testing, Error Codes, Rebooting ...........................................................................11-12

Electronic Control Heat Pump Operation ...................................................................................................13

Coil Sensors ...............................................................................................................................................13

Components Testing .............................................................................................................................13-14

Refrigeration System Sequence of Operation ...........................................................................................15

R-410A Sealed System Repair Considerations .........................................................................................16

Sealed System Refrigeration Repairs / Charging .................................................................................17-20

Hermetic Components Check ....................................................................................................................21

Reversing Valve Description/Operation .....................................................................................................22

Testing the Coil and Reversing Valve ...................................................................................................23-24

Compressor Checks .............................................................................................................................25-26

Compressor Replacement ....................................................................................................................27-28

Routine Maintenance ............................................................................................................................29-30

Performance Test Data Sheet ....................................................................................................................31

Troubleshooting ....................................................................................................................................32-41

Wiring Diagrams ...................................................................................................................................42-44

Installation Accessories .............................................................................................................................45

Installation Instructions for “WSD” Sleeve ............................................................................................46-47

Installation Instructions for Bafe Adapter Kit ............................................................................................48

Seal Gasket Installation Instructions ..........................................................................................................49

Installation Instructions for Internal Drain Kit (IDK) ....................................................................................50

Assembly and Installation Instructions for Drain Kit (DK) ..........................................................................51

Installation Instructions for Sub-Base ........................................................................................................52

Installation Instructions for Architectural Grille Model AG-48-49 ..........................................................53-54

Warranty ....................................................................................................................................................55

Technical Assistance ..................................................................................................................................56

1

IMPORTANT SAFETY INFORMATION

The information contained in this manual is intended for use by a qualied service technician who is familiar

with the safety procedures required for installation and repair, and who is equipped with the proper tools and

test instruments required to service this product.

Installation or repairs made by unqualied persons can result in subjecting the unqualied person making

such repairs as well as the persons being served by the equipment to hazards resulting in injury or electrical

shock which can be serious or even fatal.

Safety warnings have been placed throughout this manual to alert you to potential hazards that may be

encountered. If you install or perform service on equipment, it is your responsibility to read and obey these

warnings to guard against any bodily injury or property damage which may result to you or others.

PERSONAL INJURY OR DEATH HAZARDS

ELECTRICAL HAZARDS:

Unplug and/or disconnect all electrical power to the unit before performing inspections, •

maintenance, or service.

Make sure to follow proper lockout/tag out procedures.•

Always work in the company of a qualied assistant if possible. •

Capacitors, even when disconnected from the electrical power source, retain an electrical charge •

potential capable of causing electric shock or electrocution.

Handle, discharge, and test capacitors according to safe, established, standards, and approved •

procedures.

Extreme care, proper judgment, and safety procedures must be exercised if it becomes necessary •

to test or troubleshoot equipment with the power on to the unit.

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read

and obey all safety messages.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury,

and tell you what will happen if the instructions are not followed.

This is a safety Alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol with the word “WARNING”

or “CAUTION”. These words mean:

You can be killed or seriously injured if you do not follow instructions.

You can receive minor or moderate injury if you do not follow instructions.

A message to alert you of potential property damage will have the

word “NOTICE”. Potential property damage can occur if instructions

are not followed.

WARNING

CAUTION

NOTICE

2

Do not spray or pour water on the return air grille, discharge air grille, evaporator coil, control panel, •

and sleeve on the room side of the air conditioning unit while cleaning.

Electrical component malfunction caused by water could result in electric shock or other electrically •

unsafe conditions when the power is restored and the unit is turned on, even after the exterior is dry.

Never operate the A/C unit with wet hands.•

Use air conditioner on a single dedicated circuit within the specied amperage rating. •

Use on a properly grounded outlet only.•

Do not remove ground prong of plug.•

Do not cut or modify the power supply cord.•

Do not use extension cords with the unit.•

Follow all safety precautions and use proper and adequate protective safety aids such as: gloves, •

goggles, clothing, adequately insulated tools, and testing equipment etc.

Failure to follow proper safety procedures and/or these warnings can result in serious injury or death. •

REFRIGERATION SYSTEM HAZARDS:

Use approved standard refrigerant recovering procedures and equipment to relieve pressure before •

opening system for repair.

Do not allow liquid refrigerant to contact skin. Direct contact with liquid refrigerant can result in minor •

to moderate injury.

Be extremely careful when using an oxy-acetylene torch. Direct contact with the torch’s ame or hot •

surfaces can cause serious burns.

Make sure to protect personal and surrounding property with re proof materials.•

Have a re extinguisher at hand while using a torch.•

Provide adequate ventilation to vent off toxic fumes, and work with a qualied assistant whenever •

possible.

Always use a pressure regulator when using dry nitrogen to test the sealed refrigeration system for •

leaks, ushing etc.

Make sure to follow all safety precautions and to use proper protective safety aids such as: gloves, •

safety glasses, clothing etc.

Failure to follow proper safety procedures and/or these warnings can result in serious injury or death. •

MECHANICAL HAZARDS:

Extreme care, proper judgment and all safety procedures must be followed when testing, •

troubleshooting, handling, or working around unit with moving and/or rotating parts.

Be careful when, handling and working around exposed edges and corners of sleeve, chassis, and •

other unit components especially the sharp ns of the indoor and outdoor coils.

Use proper and adequate protective aids such as: gloves, clothing, safety glasses etc.•

Failure to follow proper safety procedures and/or these warnings can result in serious injury or death.•

3

PROPERTY DAMAGE HAZARDS

FIRE DAMAGE HAZARDS:

Read the Installation/Operation Manual for this air conditioning unit prior to operating.•

Use air conditioner on a single dedicated circuit within the specied amperage rating. •

Connect to a properly grounded outlet only.•

Do not remove ground prong of plug.•

Do not cut or modify the power supply cord.•

Do not use extension cords with the unit.•

Failure to follow these instructions can result in re and minor to serious property damage.•

WATER DAMAGE HAZARDS:

Improper installation maintenance, or servicing of the air conditioner unit, or not following the above •

Safety Warnings can result in water damage to personal items or property.

Insure that the unit has a sufcient pitch to the outside to allow water to drain from the unit. •

Do not drill holes in the bottom of the drain pan or the underside of the unit. •

Failure to follow these instructions can result in result in damage to the unit and/or minor to serious •

property damage.

4

INTRODUCTION

This service manual is designed to be used in conjunction with the operation and installation manuals provided

with each unit.

This service manual was written to assist the professional HVAC service technician to quickly and accurately

diagnose and repair any malfunctions of this product.

This manual, therefore, will deal with all subjects in a general nature. (i.e. All text will pertain to all models).

IMPORTANT:

It will be necessary for you to accurately identify the unit you are

servicing, so you can be certain of a proper diagnosis and repair.

(See Unit Identication.)

Return

Air Grille

Decorative

Front

WSD

Sleeve

6

543

21

BA

76

5

3

C

SW

#

L

E

D

O

M

B01A70

Airflow

Rotate

Discharge

Grille

1" Diameter Plug

5

FRIEDRICH WALLMASTER MODEL NUMBER CODE

W S 08 C 1 0 A

1st DIGIT - FUNCTION

W = Thru-The-Wall, WallMaster Series

2nd DIGIT - TYPE

S = Straight Cool

E = Electric Heat

Y = Heat Pump

3rd & 4th DIGITS - APPROXIMATE BTU/HR (Cooling)

Heating BTU/HR capacity listed in Specications/Performance Data Section

5th DIGIT - ALPHABETICAL MODIFIER

6th DIGIT - VOLTAGE

1 = 115 Volts

3 = 230-208 Volts

7th DIGIT

0 = Straight Cool & Heat Pump Models

3 = 3 KW Heat Strip, Nominal

8th DIGIT

Major Change

AKAX00001

A = JanD = Apr G = JulK = Oct

B = FebE = May H = AugL = Nov

C = MarF = Jun J = SepM = Dec

PRODUCT LINE

X = WallMaster

MONTH MANUFACTURED

WallMaster Serial Number Identification Guide

SERIAL NUMBER

YEAR MANUFACTURE

D

PRODUCTION RUN NUMBER

AK = 2010

AA = 2011

AB = 2012

AC = 2013

AD = 2014

AE = 2015

AF = 2016

AG = 2017

AH = 2018

AJ = 2019

6

2010 PERFORMANCE DATA

Sleeve / Chassis Dimensions

27" Sleeve

Height (inches) 16 3/4 16 3/4 16 3/4

Width (inches)272727

Depth (inches) 16 3/4 16 3/4 16 3/4

Friedrich WSC

Sleeve

Fedders A

Sleeve

Fedders B Sleeve*

Sleeve Dimensions

WidthMax. Depth

WSD Sleeve 16 3/427 16 3/4237 1/2 9/16 17 1/4 27 1/415 5/16

Chassis 15 3/4 26 1/22122-----

Depth

with

Front

Minimum

Extension

Into Room

Minimum

Extension

Outside

Height

TTW Finished Hole

Height WidthDepth

Model

WALLMASTER

Specifications

WallMaster Heat Pump heating information (shown in red) indicates heat pump heating performance. WallMaster Electric Heat heating information (shown in red)

indicates electric heat strip performance. For WallMaster Heat Pump electric heating performance refer to corresponding WallMaster Electric Heat model.

Estar

Model

Cooling

Capacity Btu

Heating

Capacity Btu

Volts

Rated

Cooling

Amps Cooling Watts

Heating

Amps

Heating

Watts

Energy

Efciecy Ratio

EER

Moisture

Removal

Pints/HR

Room

Side Air

Circulation

CFM Sleeve

Net Weight

Lbs

WALLMASTER

Cool only

WS08C10A 7800 NA 115 7.1 788 NA NA 9.9 1.2 250 WSD 93

WS10C10A 9700 NA 115 10.0 1032 NA NA 9.4 2.4 257 WSD 103

WS12C10A 11900 NA 115 11.8 1266 NA NA 9.4 3.3 295 WSD 112

WS10C30A 9500/9200 NA 230/208 4.5/4.7 989/958 NA NA 9.6/9.6 1.5 300 WSD 101

WS13C30A 12600/12300 NA 230/208 6.3/6.7 1340/1309 NA NA 9.4/9.4 3.6 290 WSD 109

WS15C30A 14500/14500 NA 230/208 8.3/8.2 1706/1706 NA NA 8.5/8.5 4.2 290 WSD 119

Heat Pumps

WY09C33A 9300/9000 7300/7300 230/208 4.4/4.7 989/957 3.8/4.0 839/793 9.4/9.4 2.1 250 WSD 103

WY12C33A 12000/11800 9350/9200 230/208 6.1/6.4 1395/1372 4.8/5.1 1062/1010 8.6/8.6 2.6 275 WSD 111

Cool with Electric Heat

WE10C33A 9500/9200 11000/9100 230/208 4.5/4.7 989/958 16.0/14.7 3550/2950 9.6/9.6 1.5 300 WSD 121

WE13C33A 12600/12300 11000/9100 230/208 6.3/6.7 1340/1309 16.0/14.7 3550/2950 9.4/9.4 3.6 290 WSD 107

WE15C33A 14500/14500 11000/9100 230/208 8.3/8.8 1706/1706 16.0/14.7 3550/2950 8.5/8.5 4.2 290 WSD 116

DEFROST CONTROL: Initiated at 30°F (outdoor coil temperature for two

consecutive minutes) and terminated at 43°F (outdoor coil temperature). During

defrost, the compressor stops and the electric heat starts, then operates wit

h

the fan to maintain indoor comfort. The unit remains in electric heat mode.

DEFROST DRAIN: Drain automatically opens at approximately 50°F to prevent

condensate from freezing inside drain pan.

Note: all models will produce condensate. If condensate disposal is desired, an

optional drain kit is available.

As an partner, Friedrich Air Conditioning Co. has determined that the selected

(

) meet the guidelines for energy efﬁciency.

All models use

environmentally

friendly R-410A

refrigerant.

R-410A

WS08C10A 57 23 55 60 129 167 65 98 11 31 154 462 7.1 32.0 32.5 257 1085 15

WS10C10A 53 27 53 53 134 177 63 98 10 36 145 500 10.0 40.0 37.0 260 1080 15

WS12C10A 54 26 52 55 128 169 60 106 11 28 145 500 11.8 57.0 45.0 300 1380 15

WS10C30A 55 25 55 60 123 165 66 100 14 28 155 440 4.5 18.5 39.0 300 1400 15

WS13C30A 51 29 51 51 134 179 59 100 8 40 138 535 6.3 26.0 40.0 280 1300 15

WS15C30A 45 35 45 46 135 181 54 101 9 40 130 545 8.3 41.0 49.0 250 1345 15

WY09C33A 54 26 54 54 123 164 65 101 12 22 150 450 4.4 3.8 20.0 40.5 251 1335 20

WY12C33A 51 29 51 51 127 147 58 101 12 26 145 475 6.1 4.8 33.0 265 1330 20

WE10C33A 56 24 56 56 128 150 58 110 4 24 153 477 4.5 16.0 18.5 39.0 260 1455 20

WE13C33A 46 34 46 46 128 174 55 99 9 34 135 500 6.3 16.0 26.0 40.0 240 1350 20

WE15C33A 45 35 45 46 135 181 54 101 9 40 130 545 8.3 16.0 41.0 43.0 250 1345 20

*Rating Conditions: 80 degrees F, room air temp. & 50% relative humidity, with 95 degree F, outside air temp & 40% relative humidity, all systems use R410A

Dischar

ge

Temp

Suction

Temp

Liquid

Temp

Super

Heat

Evap

CFM

Motor

RPM

Locked

Rotor Amps

Charge in

OZ.

BREAKER

FUSE

60 Hertz

Amps

Sub-

Coolin

g

OPERATING

PRESSURES

ELECTRICAL RATINGS

R410A

Suction

Dischar

ge

Amps

Cool

Amps

Heat

WALLMASTER

EVAPORATOR AIR TEMP.

DEG. F

EVAPORATOR TEMP.

DEG. F

CONDENSER

TEMPERATU

DEG. F

RE

Discharge Air

Temp. Drop

F.

T(in)

T(out)

COOLING

PERFORMANCE

DATA*

7

Wire Size Use ONLY wiring size recommended for single outlet branch circuit.

Fuse/Circuit Breaker Use ONLY the correct HACR type and size fuse/circuit breaker. Read electrical ratings on unit’s

rating plate. Proper circuit protection is the responsibiity of the homeowner.

Grounding Unit MUST be grounded from branch circuit through service cord to unit, or through separate

ground wire provided on permanently connected units. Be sure that branch circuit or general

purpose outlet is grounded.

Receptacle The eld supplied outlet must match plug on service cord and be within reach of service cord.

Do NOT alter the service cord or plug. Do NOT use an extension cord. Refer to the table above

for proper receptacle and fuse type.

The consumer - through the AHAM Room Air Conditioner Certication Program - can

be certain that the AHAM Certication Seal accurately states the unit’s cooling and

heating capacity rating, the amperes and the energy efciency ratio.

ELECTRICAL DATA

ELECTRIC SHOCK HAZARD

WARNING

Turn off electric power before service or

installation.

All electrical connections and wiring MUST be

installed by a qualied electrician and conform to

the National Electrical Code and all local codes

which have jurisdiction.

Failure to do so can result in personal injury or

death.

Not following the above WARNING could result in re or

electically unsafe conditions which could cause moderate

or serious property damage.

Read, understand and follow the above warning.

NOTICE

FIRE HAZARD

*HACR: Heating Air Conditioning and Refrigeration

Plug/Outlet/Circuit Rating

Model Numbers

Circuit Rating

Breaker or T-D Fuse

Plug Face

(NEMA#)

Wall Outlet

Appearance

WS08C10A, WS10C10A,

WS12C10A

125V - 15A 5 - 15P

WS10C30A, WS13C30A,

WS15C30A

250V - 15A 6 - 15P

WE10C33A, WE13C33A,

WE15C33A, WY09C33A,

WY12C33A

250V - 20A 6 - 20P

6

WARMER – Touch the

button to raise the room air temperature.

7

Press both the

and

buttons at the same time to switch

the temperature from Fahrenheit (°F) to Celsius (°C). Repeat

Step 7 to switch from °C back to °F.

To adjust fan speed

8

Touch the Fan Speed button to see the current setting. Touch

it again to change speed. F1 is the lowest setting (SLEEP

SETTING / LOW), F2 is MEDIUM, and F3 is HIGH.

To activate Smart Fan (WS cool-only models)

9

There is a fourth option, SF, when selecting the fan speed. This is

the SMART FAN function. SMART FAN DOES NOT OPERATE

IN CONJUNCTION WITH THE FAN ONLY MODE.

To activate Smart Fan (WY/WE heat-cool models)

9

Press the Smart Fan button to activate the Smart Fan. The light

will indicate that this feature is in use.

Smart Fan will adjust the fan speed automatically to maintain the

desired comfort level. For example, if the outside doors in your home

are opened for an extended period of time, or more people enter a

room, Smart Fan may adjust to a higher fan speed to compensate

for the increased heat load. This keeps you from having to adjust

the fan speed on your own.

To set the hour clock

10

Touch the Set Hour button to see t he c urrent s etting. The

.)ylno ruoh( emit etamixorppa eht si deyalpsid si taht rebmun

Use the

and buttons to change the settings. BE SURE

TO SET A.M. AND P. M. ACCORDINGLY. (P. M. is indicated by

a red light in the upper left corner of the display).

ELECTRONIC CONTROL OPERATION

Temp/Hour

Cool

Money Saver

®

Fan Only

Clock

Start Time

Stop Time

Power

Fan

Speed

Mode

PM

Timer

On/Off

Set

Hour

Figure 1: WS Model cool-only control panel

Temp/Hour

Power

PM

Cool

Fan Only

Heat

Clock

Start Time

Stop Time

Smart

Fan

Speed

Mode

Timer

On/Off

Money

Saver

Set

Hour

2 3

4

1

6

5

7

9

8

10 11 12

14

13

Figure 2: WY/WE Model heat-cool control panel

Figure 1: WS Model cool-only control panel Figure 2: WY/WE Model heat-cool control panel

If the air conditioner is installed and plugged into a proper receptacle,

it is ready to go. The rst time the unit is started, the compressor will

delay for three minutes. See Automatic Component Protection on the

following page.

Touch the Power button once. The unit will automatically be in

Cool mode with the temperature set at 75°F (24°C) and the fan

speed at F1, the sleep setting.

When you rst turn the unit on, it will be in the Cool mode with constant

fan.

On WS cool-only models, touch the Mode button once to activate

the MoneySaver® (See item 14 for MoneySaver instructions on

WY/WE models).

MoneySaver® is a feature that cycles the fan with the compressor

so that the fan does not run all the time. This saves energy and

improves dehumidication. MoneySaver® will also run to test

the temperature if the off cycle is too long. Or you may prefer

constant fan for more air movement. (To return to constant fan,

touch the Mode button two more times).

On WY/WS heat-cool models, touch the Mode button once to

activate the Fan Only feature. The Fan Only setting will circulate

air in the room without the compressor coming on.

In order to run the fan by itself, do the following:

Continuing from MoneySaver® mode, touch the Mode button

once to activate the Fan Only feature (WS cool-only models).

To adjust temperature

Use the Mode button to select either the Cool or MoneySaver®

function (or Heat for WY/WE heat-cool models)

COOLER – Touch the button to lower the room air

temperature.

1

2

3

4

5

To start unit

To set mode of operation

8

To set the timer

NOTE: Set the HOUR CLOCK (Set Hour) before attempting to set

timer functions.

You can set the Start Time and Stop Time a minimum of one hour

apart, and a maximum of 23 hours apart.

11

After setting the time, press the Set Hour button once (Start

light on). Use the

and

eht taht emit eht tceles ot snottub

unit will START.

12

After selecting the Start Time, press the Set Hour button once.

(Stop Light on). Use the

and

buttons to select the time

that the unit will STOP. After selecting the stopping time, press

the Set Hour button once.

13

Press the Timer On/Off button (light turns on) to activate the

timer function. To deactivate this function, press the Timer On/

Off button once again (light turns off). Once the on and off times

have been selected, they will remain in memory and cycle daily

until changed.

NOTE: If the unit is unplugged or the power is interrupted, the HOUR

must be reset or the Timer On/Off will not function when desired.

To Activate Money Saver (WY/WE models)

14

Press the Money Saver button to activate the Money Saver

feature. The light will indicate the Money Saver is in use.

MoneySaver

®

is a feature that cycles the fan with the com pres

sor so that the fan does not run all the time. This saves energy

i fidim uh ed sevorpmi dnarevaSyenoM .noit ac

®

will also run to test

the temperature if the off cycle is too long. Or you may prefer

,naf tnatsnoc ot nruter oT( .tnem evom ria erom rof naf tnats noc

touch the Mode button two more times).

9

CHECKING ROOM TEMPERATURE

1. Check the room temperature at the electronic control

pad by pressing at the same time, the Fan Speed

button and the Temp/Hour button (see gures 1

and 2).

2. The indoor temperature will display for 10 seconds.

Indoor temperature can be viewed in all modes, including

the Test Mode. The display can be changed back to

the SET temperature by pressing any key (except the

Power (on/off button) or it can do so automatically after

10 seconds have elapsed.

Using the remote control

To start unit

1

POWER - Press the Power button once. The unit will automatically

start in the mode and fan speed it was last left on.

To set mode of operation

2

COOL - Press the Cool button to automatically switch the operat-

ing mode to COOL.

3

FAN ONLY - Press the Fan Only button if you want to run the

fan only.

4

HEAT (WY/WE m odels only) - P ress t he Heat b utton to

automatically switch the operating mode to HEAT.

5

MoneySaver

®

- Press the Money Saver

®

button to activate

the MoneySaver

®

feature. This feature cycles the fan with the

compressor so that the fan does not run all the time.

To adjust temperature

6

WARMER - Press the

Warmer button to raise the temperature sett

tt

ing.

7

COOLER - Press the

Cooler button to lower the temperature se

To adjust fan speed

8

FAN SPEED - Press the Fan Speed button to see the current

setting. Press again to change the fan speed. F1 is the lowest

setting (SLEEP / LOW), F2 is MEDIUM, F3 is HIGH, and SF is

the SMART FAN setting.

To set the hour clock

9

SET HOUR CLOCK - Press the Set Hr. button once to see the

current clock setting. Continue pressing the button until you

arrive at the current time (Hour only). Minutes are not shown on

the display. Make sure that the A.M. / P. M. setting is correct.

To set the timer

NOTE: You can set the START and STOP times a minimum of one

hour apart, and a maximum of 23 hours apart.

10

TIMER START - Press Start to view the current start time for cool-

ing. Continue pressing the START button until you arrive at the start

time you desire. The start time for cooling will then be set.

11

TIMER STOP - Press the Stop button. Continue pressing the

STOP button until you arrive at the stop time you desire. The

stop time for cooling will then be set.

12

TIMER ON / O FF - P ress t he O n/Off button (under Timer

Operation .remit eht )ffo thgil( etavitcaed ro )no thgil( etavitca ot )

Once the on and off times have been selected, they will remain

in memory and cycle daily until changed.

NOTE: If the unit is unplugged or the power is interrupted, the Set Hr.

function must be reset or the Timer On/Off function will not work.

WY/WE heat-cool model remote control

Figure 3

Money

F a n

Timer Operation

Set Hr.

Stop

Start

Temperature

F a n

Cool

On/Off

Power

Cooler

Warmer

Only Speed Saver

®

Heat

10

ELECTRONIC CONTROL PANEL

ACTIVATING TEST MODE

Activate Test Mode by pressing at the same time, the Mode

button and the Temp/Hour button (see gures 4 and 5).

The LEDs for Set/Hour: “Star t Time” and “Stop Time” will

blink 1 bps while Test Mode is active.

Test Mode has a duration of 90 minutes. Test Mode can be

activated under any function, including Off.

Test Mode is cancelled by pressing the Power (on/off)

button, unplugging the unit, or when the 90 minutes times

out.

Test Mode settings are factory default of:

Unit operation On, MoneySaver On, Cool Mode, 60

degrees F, speed fan on High. “Timer” and “Set Hour”

features are non-functional.

Test Mode overrides the three minute compressor Lock-

out, all delays for fan motor start, speed change, and when

switching modes.

TESTING THE ELECTRONIC CONTROL

Figure 4: “WS” Cooling only models

Electronic Control Panel

Figure 5: “WE”/”WY” heat/cool models

Electronic Control Panel

Error Code Mode is used to display all error codes

stored since reset. It is a sub-mode of Test Mode. Unit

must be in Test Mode to enter the Error Code function.

Activating Error Code Mode: Press the TIMER On/Off”

button (see gures 4 and 5). The LED for the TIMER On/

Off will ash 1 bps (beats per second) while Error Code

Mode is active. Pressing the Temp/Hour button will

display “00”. Consecutive presses will scroll through all

error codes stored. Press the Temp/Hour button to

see the reverse order of the error codes. When the end

of the stored error codes is reached the temperature Set

Point will appear. (Each error code is listed once)

Exiting Error Code Mode: press the Timer On/Off

button.

Clearing Error Codes: Error codes are cleared

from the memory by exiting from Error Code Mode.

MEMORY

The electronic control has a memory to retain all

functions and settings, as set up by the user, in the event

of a power failure. For example: once power is restored

to the unit, there is a two second delay before the fan

comes on and approximately three minutes delay before

the compressor is activated providing that the mode was

set for cooling and the set point temperature has not

been met in the room.

ERROR CODE MODE

Temp/Hour

Cool

Money Saver

®

Fan Only

Clock

Start Time

Stop Time

Power

Fan

Speed

Mode

PM

Timer

On/Off

Set

Hour

Temp/Hour

Power

PM

Cool

Fan Only

Heat

Clock

Start Time

Stop Time

Smart

Fan

Speed

Mode

Timer

On/Off

Money

Saver

Set

Hour

2 3

4

1

6

5

7

9

8

10 11 12

14

13

11

Automatic component protection

Your unit is equipped with Automatic Component Protection.

To protect the compressor of the unit, there is a three minute delay

if you turn the unit off or if power is interrupted. The fan will not be

affected. Also, if you switch from Cool mode to Fan Only mode, and

switch back to Cool mode, there is a three-minute delay before the

compressor comes back on.

ERROR CODES LISTING FOR “WS” MODELS

E1 SHORT CYCLE SITUATION: Dened as a

compressor that starts and stops more frequently

than it should (more than 6 times per hour).

E2 KEYBOARD STUCK ERROR: If any key button

is stuck or pressed for 20 seconds or more, the

unit considers it stuck. If a key is stuck it will be

ignored until released. If the “Mode” key is stuck,

the unit’s function will default to Cool mode.

E3 FROST PROBE OPEN: Normal operation is

allowed. Replace probe.

E4 FROST PROBE SHORT: Normal operation is

allowed. Replace probe.

E5 INDOOR PROBE OPEN: Control assumes

indoor ambient temperature is 90 degrees F and

unit will operate. Replace probe.

E6 INDOOR PROBE SHORT: Control assumes

ambient temperature is 90 degrees F and unit

will operate. Replace probe.

(See note and other infomation below)

ERROR CODES LISTING FOR “WE/WY” MODELS

E1 SHORT CYCLE SITUATION: Dened as a

compressor that starts and stops more frequently

than it should (more than 6 times per hour).

E2 KEYBOARD STUCK ERROR: If any key button

is stuck or pressed for 20 seconds or more, the

unit considers it stuck. If a key is stuck it will be

ignored until released. If the “Mode” key is stuck,

the unit’s function will default to Cool mode.

E3 AMBIENT (INDOOR) AIR PROBE OPEN

OR SHORT: Control will assume ambient

temperature is 90 degrees F when in Cool mode

and 60 degrees F when in Heat mode. Unit will

operate (see note below).

E4 EVAPORATOR TEMPERATURE PROBE

OPEN OR SHORT: Normal operation is allowed.

Replace probe (see note below).

E5 CONDENSER TEMPERATURE PROBE

OPEN OR SHORT: Normal operation is allowed.

Replace probe.

E7 MOTOR OPERATION

E9 HEAT PUMP FAILURE

NOTE: All error codes display for probes open or shorted will

allow unit to operate. Unit may ice up if faulty components

are not replaced.

Indoor Coil Frost Probe Sensor:

Outdoor Coil Frost Probe Sensor (on WY models):

Disables the compressor at 30 degrees F. Compressor

resumes operation when temperature reaches 43 +/- 5

degrees F.

Indoor Air Probe Sensor:

REBOOT THE CONTROL PANEL

Reboot the control panel as follows: With the unit on,

simultaneously hold down the Mode button and the

Temperature Arrow button for approximately 10

seconds. If the panel will reboot, you will hear the fan come

on and the temperature window will read 60 degrees. If this

happens, all you need to do is turn the unit off for about 10

seconds and then turn it back on to nish the reboot cycle.

If the panel does not reboot, you will most likely need to

replace the electronic control.

Disables compressor at 30 degrees F+/- 3 degrees F.

Compressor resumes operation when indoor coil temperature

reaches 55 degrees F.

Control range is 60 degrees F to 90 degrees F +/- 3

degrees F.

12

13

ELECTRONIC CONTROL

OPERATION

Heat Pump Models

If the indoor ambient air themister reads 55 degrees or

lower, the control will turn off the compressor and turn

on the electric heat and continue fan operation until temp

setting is satised. Then revert to standard heat pump

operation.

If the compressor is time delayed, the control will:

1. Turn on the electric heat until the compressor is not time

delayed.

2. When the compressor’s 3 minute time delay is over,

turn off the electric heat, wait 5 seconds, then turn on the

compressor.

Defrost:

If the outdoor coil thermister reads 30 degrees or lower

for 2 minutes continuously, the control will turn off the

compressor and turn on the electric heat and continue fan

operation.

Positioning of the Coil Sensors (Thermisters) is critical to

proper operation of the Electronic Control.

Ensure that sensors are positioned as indicated in the

illustrations below.

If the outdoor coil thermister reaches 43 degrees and

the compressor has waited the standard delay time of

180-240 seconds, the control will:

1. Turn off the backup electric heat

2. Wait 5 seconds

3. Turn on the compressor

4. Continue fan operation.

ELECTRIC SHOCK HAZARD

WARNING

Disconnect power to the unit before

servicing. Failure to follow this warning

could result in serious injury or death.

COIL SENSORS

FAN MOTOR - TEST

1. Make sure the motor has cooled down.

2. Disconnect the fan motor wires from the control board.

3. Test for continuity between the windings also, test to

ground.

4. If any winding is open or grounded replace the motor.

Fan Motor

FAN MOTOR

A single phase permanent split capacitor motor is used to drive

the evaporator blower and condenser fan. A self-resetting

overload is located inside the motor to protect against high

temperature and high amperage conditions. (See Figure 23)

ELECTRIC SHOCK HAZARD

WARNING

Disconnect power to the unit before

servicing. Failure to follow this warning

could result in serious injury or death.

COMPONENTS TESTING

Heating Element

HEATING ELEMENT

(“WE” &”WY” Models)

All “WE” and “WY” models are equipped with a 3.3 KW

heating element.

The heating element has two heater limit switches

(bimetal thermostats) connected in series with it. The

Primary limit located near the bottom, will open the

circuit when the temperature reaches 130°F +/-5°. The

Secondary is a high limit switch near the top of the

element. It is designed to open the circuit at 165°F +/-8°.

Should the fan motor fail or filter become clogged etc.,

the high limit switch will open and interrupt the power to

the heater before reaching an unsafe temperature

condition.

Test the heater element for continuity below 130°F.

Not actual element - for reference only

14

CAPACITORS

ELECTRIC SHOCK HAZARD

WARNING

Turn off electric power before servicing.

Discharge capacitor with a 20,000 Ohm 2 Watt

resistor before handling.

Failure to do so may result in personal injury,

or death.

Many motor capacitors are internally fused. Shorting the

terminals will blow the fuse, ruining the capacitor. A 20,000

ohm 2 watt resistor can be used to discharge capacitors

safely. Remove wires from capacitor and place resistor

across terminals. When checking a dual capacitor with

a capacitor analyzer or ohmmeter, both sides must be

tested.

Capacitor Check with Capacitor Analyzer

The capacitor analyzer will show whether the capacitor is

“open” or “shorted.” It will tell whether the capacitor is within

its micro farads rating and it will show whether the capacitor

is operating at the proper power-factor percentage. The

instrument will automatically discharge the capacitor when

the test switch is released.

Capacitor Connections

The starting winding of a motor can be damaged by a

shorted and grounded running capacitor. This damage

usually can be avoided by proper connection of the running

capacitor terminals.

From the supply line on a typical 230 volt circuit, a 115 volt

potential exists from the “R” terminal to ground through a

possible short in the capacitor. However, from the “S” or

start terminal, a much higher potential, possibly as high as

400 volts, exists because of the counter EMF generated

in the start winding. Therefore, the possibility of capacitor

failure is much greater when the identied terminal is

connected to the “S” or start terminal. The identied

terminal should always be connected to the supply line, or

“R” terminal, never to the “S” terminal.

When connected properly, a shorted or grounded running

capacitor will result in a direct short to ground from the “R”

terminal and will blow the line fuse. The motor protector

will protect the main winding from excessive temperature.

DRAIN PAN VALVE

During the cooling mode of operation, condensate which

collects in the drain pan is picked up by the condenser

fan blade and sprayed onto the condenser coil. This as-

sists in cooling the refrigerant plus evaporating the water.

During the heating mode of operation, it is necessary that

water be removed to prevent it from freezing during cold

outside temperatures. This could cause the condenser

fan blade to freeze in the accumulated water and prevent

it from turning.

To provide a means of draining this water, a bellows type

drain valve is installed over a drain opening in the base

pan. This valve is temperature sensitive and will open

when the outside temperature reaches 40°F. The valve

will close gradually as the temperature rises above 40°F

to fully close at 60°F.

Drain Pan Valve

COMPONENTS TESTING (Continued)

Suction

Line

Evaporator

Coil

Metering

Device

Refrigerant

Strainer

Discharge

Line

Condenser

Coil

Compressor

Refrigerant Drier

Liquid

Line

A good understanding of the basic operation of the

refrigeration system is essential for the service technician.

Without this understanding, accurate troubleshooting of

refrigeration system problems will be more difcult and time

consuming, if not (in some cases) entirely impossible. The

refrigeration system uses four basic principles (laws) in its

operation they are as follows:

1. “Heat always ows from a warmer body to a cooler

body.”

2. “Heat must be added to or removed from a substance

before a change in state can occur”

3. “Flow is always from a higher pressure area to a lower

pressure area.”

4. “The temperature at which a liquid or gas changes state

is dependent upon the pressure.”

The refrigeration cycle begins at the compressor. Starting

the compressor creates a low pressure in the suction line

which draws refrigerant gas (vapor) into the compressor.

The compressor then “compresses” this refrigerant, raising

its pressure and its (heat intensity) temperature.

The refrigerant leaves the compressor through the discharge

Line as a hot High pressure gas (vapor). The refrigerant

enters the condenser coil where it gives up some of its

heat. The condenser fan moving air across the coil’s nned

surface facilitates the transfer of heat from the refrigerant to

the relatively cooler outdoor air.

When a sufcient quantity of heat has been removed from

the refrigerant gas (vapor), the refrigerant will “condense”

(i.e. change to a liquid). Once the refrigerant has been

condensed (changed) to a liquid it is cooled even further by

the air that continues to ow across the condenser coil.

The WallMaster design determines at exactly what point (in

the condenser) the change of state (i.e. gas to a liquid)

takes place. In all cases, however, the refrigerant must be

totally condensed (changed) to a Liquid before leaving the

condenser coil.

The refrigerant leaves the condenser Coil through the liquid

line as a warm high pressure liquid. It next will pass through

the refrigerant drier (if so equipped). It is the function of the

drier to trap any moisture present in the system, contaminants,

and large particulate matter.

The liquid refrigerant next enters the metering device. The

metering device is a capillary tube. The purpose of the

metering device is to “meter” (i.e. control or measure) the

quantity of refrigerant entering the evaporator coil.

In the case of the capillary tube this is accomplished (by

design) through size (and length) of device, and the pressure

difference present across the device.

Since the evaporator coil is under a lower pressure (due to

the suction created by the compressor) than the liquid line,

the liquid refrigerant leaves the metering device entering the

evaporator coil. As it enters the evaporator coil, the larger

area and lower pressure allows the refrigerant to expand

and lower its temperature (heat intensity). This expansion is

often referred to as “boiling”. Since the unit’s blower is moving

indoor air across the nned surface of the evaporator coil,

the expanding refrigerant absorbs some of that heat. This

results in a lowering of the indoor air temperature, hence the

“cooling” effect.

The expansion and absorbing of heat cause the liquid

refrigerant to evaporate (i.e. change to a gas). Once the

refrigerant has been evaporated (changed to a gas), it is

heated even further by the air that continues to ow across

the evaporator coil.

The particular system design determines at exactly what

point (in the evaporator) the change of state (i.e. liquid to a

gas) takes place. In all cases, however, the refrigerant must

be totally evaporated (changed) to a gas before leaving the

evaporator coil.

The low pressure (suction) created by the compressor

causes the refrigerant to leave the evaporator through the

suction line as a cool low pressure vapor. The refrigerant then

returns to the compressor, where the cycle is repeated.

REFRIGERATION SYSTEM SEQUENCE OF OPERATION

15

• R-410A pressure is approximately 60% higher than R-22 pressure.

• R-410A cylinders must not be allowed to exceed 125 F, they may leak or rupture.

• R-410A must never be pressurized with a mixture of air, it may become

ammable.

• Servicing equipment and components must be specically designed for use with R-410A and

dedicated to prevent contamination.

• Manifold sets must be equipped with gauges capable of reading 750 psig (high side) and 200

psig (low side), with a 500-psig low-side retard.

• Gauge hoses must have a minimum 750-psig service pressure rating

• Recovery cylinders must have a minimum service pressure rating of 400 psig, (DOT 4BA400

and DOT BW400 approved cylinders).

• POE (Polyol-Ester) lubricants must be used with R-410A equipment.

• To prevent moisture absorption and lubricant contamination, do not leave the refrigeration

system open to the atmosphere longer than 1 hour.

• Weigh-in the refrigerant charge into the high side of the system.

• Introduce liquid refrigerant charge into the high side of the system.

• For low side pressure charging of R-410A, use a charging adaptor.

• Use Friedrich approved R-410A lter dryers only.

The following is a list of important considerations when working with R-410A equipment

R-410A SEALED SYSTEM REPAIR CONSIDERATIONS

Do not puncture, heat, expose to ame or incinerate.

Only certied refrigeration technicians should

service this equipment.

R410A systems operate at higher pressures than

R22 equipment. Appropriate safe service and

handling practicces must be used.

Only use gauge sets designed for use with R410A.

Do not use standard R22 gauge sets.

WARNING

Refrigeration system under high pressure

16

Proper refrigerant charge is essential to proper unit operation.

Operating a unit with an improper refrigerant charge will

result in reduced performance (capacity) and/or efciency.

Accordingly, the use of proper charging methods during

servicing will insure that the unit is functioning as designed

and that its compressor will not be damaged.

Too much refrigerant (overcharge) in the system is just as bad

(if not worse) than not enough refrigerant (undercharge). They

both can be the source of certain compressor failures if they

remain uncorrected for any period of time. Quite often, other

problems (such as low air ow across evaporator, etc.) are

misdiagnosed as refrigerant charge problems. The refrigerant

circuit diagnosis chart will assist you in properly diagnosing

these systems.

An overcharged unit will at times return liquid refrigerant

(slugging) back to the suction side of the compressor eventually

causing a mechanical failure within the compressor. This

mechanical failure can manifest itself as valve failure, bearing

failure, and/or other mechanical failure. The specic type of

failure will be inuenced by the amount of liquid being returned,

and the length of time the slugging continues.

Not enough refrigerant (undercharge) on the other hand, will

cause the temperature of the suction gas to increase to the point

where it does not provide sufcient cooling for the compressor

motor. When this occurs, the motor winding temperature will

increase causing the motor to overheat and possibly cycle open

the compressor overload protector. Continued overheating of

the motor windings and/or cycling of the overload will eventually

lead to compressor motor or overload failure.

Sealed Refrigeration System contains refrigerant

and oil under high pressure.

Proper safety procedures must be followed,

and proper protective clothing must be worn

when working with refrigerants.

Failure to follow these procedures could

result in serious injury or death.

WARNING

HIGH PRESSURE HAZARD

Unplug and/or disconnect all electrical power

to the unit before performing inspections,

maintenances or service.

Failure to do so could result in electric shock,

serious injury or death.

WARNING

RISK OF ELECTRIC SHOCK

R-410A SEALED REFRIGERATION SYSTEM REPAIRS

SEALED SYSTEM REPAIRS TO COOL-ONLY MODELS REQUIRE THE INSTALLATION OF A LIQUID LINE DRIER.

SEALED SYSTEM REPAIRS TO HEAT PUMP MODELS REQUIRE THE INSTALLATION OF A SUCTION LINE DRIER.

IMPORTANT

EQUIPMENT REQUIRED:

1. Voltmeter

2. Ammeter

3. Ohmmeter

4. E.P.A. Approved Refrigerant Recovery System

5. Vacuum Pump (capable of 200 microns or less

vacuum.)

6. Acetylene Welder

7. Electronic Halogen Leak Detector capable of

detecting HFC (Hydrouorocarbon) refrigerants.

8. Accurate refrigerant charge measuring device such

as:

a. Balance Scales - 1/2 oz. accuracy

b. Charging Board - 1/2 oz. accuracy

9. High Pressure Gauge - (0 to 750 lbs.)

10. Low Pressure Gauge - (-30 to 200 lbs.)

11. Vacuum Gauge - (0 - 1000 microns)

12. Facilities for owing nitrogen through refrigeration tubing

during all brazing processes.

EQUIPMENT MUST BE CAPABLE OF:

1. Recovering refrigerant to EPA required levels.

2. Evacuation from both the high side and low side of the

system simultaneously.

3. Introducing refrigerant charge into high side of the

system.

4. Accurately weighing the refrigerant charge introduced

into the system.

17

Refrigerant Charging

NOTE: Because the Wallmaster system is a sealed system,

service process tubes will have to be installed. First install a

line tap and remove refrigerant from system. Make necessary

sealed system repairs and vacuum system. Crimp process

tube line and solder end shut. Do not leave a service valve in

the sealed system.

18

3. Install a process tube to sealed system.

4. Make necessary repairs to system.

5. Evacuate system to 200 microns or less.

6. Weigh in refrigerant with the property quantity of R-410A

refrigerant.

7. Start unit, and verify performance.

8. Crimp the process tube and solder the end shut.

Proper safety procedures must be followed,

and proper protective clothing must be worn

when working with a torch.

Failure to follow these procedures could

result in moderate or serious injury.

Proper safety procedures must be followed,

and proper protective clothing must be worn

when working with liquid refrigerant.

Failure to follow these procedures could

result in minor to moderate injury.

WARNING

CAUTION

BURN HAZARD

FREEZE HAZARD

Proper safety procedures must be followed,

and proper protective clothing must be worn

when working with a torch.

Failure to follow these procedures could

result in moderate or serious injury.

WARNING

BURN HAZARD

Method Of Charging / Repairs

The acceptable method for charging the WallMaster system

is the Weighed in Charge Method. The weighed in charge

method is applicable to all units. It is the preferred method to

use, as it is the most accurate.

The weighed in method should always be used whenever

a charge is removed from a unit such as for a leak repair,

compressor replacement, or when there is no refrigerant

charge left in the unit. To charge by this method, requires the

following steps:

1. Install a piercing valve to remove refrigerant from the

sealedsystem. (Piercing valve must be removed from the

system before recharging.)

2. Recover Refrigerant in accordance with EPA regulations.

Undercharged Refrigerant Systems

An undercharged system will result in poor performance

(low pressures, etc.) in both the heating and cooling

cycle.

Whenever you service a unit with an undercharge of

refrigerant, always suspect a leak. The leak must be

repaired before charging the unit.

To check for an undercharged system, turn the unit on,

allow the compressor to run long enough to establish

working pressures in the system (15 to 20 minutes).

During the cooling cycle you can listen carefully at the exit

of the metering device into the evaporator; an intermittent

hissing and gurgling sound indicates a low refrigerant

charge. Intermittent frosting and thawing of the evaporator

is another indication of a low charge, however, frosting

and thawing can also be caused by insufcient air over

the evaporator.

Checks for an undercharged system can be made at

the compressor. If the compressor seems quieter than

normal, it is an indication of a low refrigerant charge.

Overcharged Refrigerant Systems

A check of the amperage drawn by the compressor

motor should show a lower reading. (Check the Unit

Specication.) After the unit has run 10 to 15 minutes,

check the gauge pressures. Gauges connected to system

with an undercharge will have low head pressures and

substantially low suction pressures.

of the evaporator will not be encountered because the

refrigerant will boil later if at all. Gauges connected to

system will usually have higher head pressure (depending

upon amount of over charge). Suction pressure should be

slightly higher.

Compressor amps will be near normal or higher.

Noncondensables can also cause these symptoms. To

conrm, remove some of the charge, if conditions improve,

system may be overcharged. If conditions don’t improve,

Noncondensables are indicated.

Whenever an overcharged system is indicated, always

make sure that the problem is not caused by air ow

problems. Improper air ow over the evaporator coil may

indicate some of the same symptoms as an over charged

system.

An overcharge can cause the compressor to fail, since it

would be “slugged” with liquid refrigerant.

The charge for any system is critical. When the compressor

is noisy, suspect an overcharge, when you are sure that

the air quantity over the evaporator coil is correct. Icing

ELECTRIC SHOCK HAZARD

WARNING

Turn off electric power before service or

installation.

Extreme care must be used, if it becomes

necessary to work on equipment with power

applied.

Failure to do so could result in serious injury or

death.

Sealed Refrigeration System contains refrigerant

and oil under high pressure.

Proper safety procedures must be followed,

and proper protective clothing must be worn

when working with refrigerants.

Failure to follow these procedures could

result in serious injury or death.

WARNING

HIGH PRESSURE HAZARD

19

Page is loading ...

Friedrich WS10D30A User manual

Friedrich WS10D30A User manual

Related papers

Other documents