Electrolux EWG147540W User manual

Brand: Electrolux

Model: EWG147540W

Category: Washing machines

Type: User manual

EWG 147540 W

EN Washing Machine User Manual

Electrolux. Thinking of you.

Share more of our thinking at www.electrolux.com

CONTENTS

Safety information 2

Safety instructions 3

Product description 4

Control panel 6

First use 8

Personalisation 8

Daily use 9

Helpful hints and tips 12

Washing programmes 14

Consumption values 17

Care and cleaning 17

What to do if… 20

Technical data 23

Installation 23

Building in 28

Environment concerns 31

Subject to change without notice.

SAFETY INFORMATION

Before the installation and use of the appliance, carefully read

the supplied instructions. The manufacturer is not responsible

if an incorrect installation and use causes injuries and dam-

ages. Always keep the instructions with the appliance for fu-

ture reference.

CHILDREN AND VULNERABLE PEOPLE SAFETY

• This appliance can be used by children aged from 8 years and

above and persons with reduced physical, sensory or mental

capabilities or lack of experience and knowledge if they have

been given supervision or instruction concerning use of the

appliance

in a safe way and understand the hazards involved.

• Do not let children play with the appliance.

• Children of less than 3 years should kept away unless

continuously supervised.

• Keep all packaging away from children.

• Keep all detergents away from children.

• Keep children and pets away from the appliance door when

it is open.

• If the appliance has a child safety device, we recommend

you activate it.

GENERAL SAFETY

• Before maintenance, deactivate the appliance and discon-

nect the mains plug from the mains socket.

• Do not change the specification of this appliance.

2 electrolux

• Obey the maximum load volume of 7 kg (refer to the “Pro-

gramme chart” chapter).

• If the supply cord is damaged, it must be replaced by the

manufacturer, its service agent or similarly qualified persons

in order to avoid a hazard.

• The operating water pressure (minimum and maximum)

must be between 0,5 bar (0,05 MPa) and 8 bar (0,8 MPa)

• The ventilation openings in the base (if applicable) must not

be obstructed by a carpet.

• The appliance is to be connected to the water mains using

the new supplied hose-sets. Old hose sets must not be

reused.

SAFETY INSTRUCTIONS

INSTALLATION

• Remove all the packaging and the transit

bolts.

• Keep the transit bolts. When you move

the appliance again you must block the

drum.

• Do not install or use a damaged appli-

ance.

• Do not install or use the appliance where

the temperature is less than 0 °C or

where it is exposed to the weather.

• Obey the installation instruction supplied

with the appliance.

• Make sure that the floor where you install

the appliance is flat, stable, heat resistant

and clean.

• Do not install the appliance where the ap-

pliance door can not be fully opened.

• Always be careful when you move the

appliance because it is heavy. Always

wear safety gloves.

• Make sure that there is air circulation be-

tween the appliance and the floor.

• Adjust the feet to have the necessary

space between the appliance and the

carpet.

Electrical connection

Warning! Risk of fire and electrical

shock.

• The appliance must be earthed.

• Make sure that the electrical information

on the rating plate agrees with the power

supply. If not, contact an electrician.

• Always use a correctly installed shock-

proof socket.

• Do not use multi-plug adapters and ex-

tension cables.

• Make sure not to cause damage to the

mains plug and to the mains cable.

Should the appliance power supply cable

need to be replaced, this must be carried

out by our Service Centre.

• Connect the mains plug to the mains

socket only at the end of the installation.

Make sure that there is access to the

mains plug after the installation.

• Do not pull the mains cable to disconnect

the appliance. Always pull the mains

plug.

• Do not touch the mains cable or the

mains plug with wet hands.

• Only for UK and Ireland. The appliance

has a 13 amp mains plug. If it is necessa-

ry to change the fuse in the mains plug,

use a 13 amp ASTA (BS 1362) fuse.

•

This appliance complies with the E.E.C.

Directives.

electrolux 3

Water connection

• Make sure not to cause damage to the

water hoses.

• The appliance is to be connected to the

water mains using the new supplied

hose-sets. Old hose sets must not be

reused.

• Before you connect the appliance to new

pipes or pipes not used for a long time,

let the water flow until it is clean.

• The first time you use the appliance,

make sure that there is no leakage.

USE

Warning! Risk of injury, electrical

shock, fire, burns or damage to the

appliance.

• Use this appliance in a household envi-

ronment.

• Obey the safety instructions on the deter-

gent packaging.

• Do not put flammable products or items

that are wet with flammable products in,

near or on the appliance.

• Do not touch the glass of the door while

a programme operates. The glass can be

hot.

• Make sure that you remove all metal ob-

jects from the laundry.

• Do not put a container to collect possible

water leakage under the appliance. Con-

tact the Service to ensure which acces-

sories can be used.

CARE AND CLEANING

Warning! Risk of injury or damage to

the appliance.

• Do not use water spray and steam to

clean the appliance.

• Clean the appliance with a moist soft

cloth. Only use neutral detergents. Do

not use abrasive products, abrasive

cleaning pads, solvents or metal objects.

DISPOSAL

Warning! Risk of injury or suffocation.

• Disconnect the appliance from the mains

supply.

• Cut off the mains cable and discard it.

• Remove the door catch to prevent chil-

dren and pets to get closed in the appli-

ance.

SERVICE

• Contact the Service to repair the appli-

ance. We recommend only the use of

original spare parts.

PRODUCT DESCRIPTION

Your new appliance meets all modern requirements for effective treatment of laundry

with low water, energy and detergent consumption. Its new washing system allows

total use of detergent and reduces water consumption so saving energy.

4 electrolux

1 2 7 8 9

Detergent dispenser drawer

Control panel

Door opening handle

Rating plate

Drain pump

Front adjustable feet

Water drain hose

Mains cable

Water inlet valve

Back adjustable feet

DETERGENT DISPENSER DRAWER

Compartment for detergent used for

prewash and soak phase or for stain re-

mover used during the stain action phase (if

available). The prewash and soak detergent

is added at the beginning of the wash pro-

gramme. The stain remover is added dur-

ing the stain action phase.

Compartment for powder or liquid de-

tergent used for main wash. If using liquid

detergent pour it just before starting the

programme.

Compartment for liquid additives (fabric

softener, starch).

Follow the product manufacturer’s recom-

mendations on quantities to use and do not

exceed the «MAX» mark in the detergent

dispenser drawer. Any fabric softener or

starching additives must be poured into the

compartment before starting the wash pro-

gramme.

CHILD SAFETY DEVICE

Make sure that children or pets do not

climb into the drum. To prevent children

and pets becoming trapped inside the

drum the machine incorporates a special

feature. To activate this device, rotate the

button (without pressing it) inside the door

clockwise until the groove is horizontal. If

necessary use a coin.

electrolux 5

To disable this device and restore the pos-

sibility of closing the door, rotate the button

counterclockwise until the groove is vertical.

CONTROL PANEL

Below is a picture of the control panel. It shows the programme selector dial as well as

the buttons, pilot lights and the display. These are presented by relevant numbers on

the following pages.

1 2 3 4 5 6 7 8 9

Programme selector dial

TEMPERATURE button

SPIN button

EASY IRON button

EXTRA RINSE button

DELAY START button

Display

START/PAUSE button

TIME MANAGER buttons

PROGRAMME SELECTOR DIAL

It allows you to switch the appliance on/off

and/or to select a programme.

TEMPERATURE

This button allows you to increase or de-

crease the washing temperature.

SPIN REDUCTION

By pressing this button you can change the

spin speed of the selected programme.

EASY IRON

By selecting this option the laundry is gently

washed and spun to avoid any creasing. In

this way ironing is easier. Furthermore the

machine will perform some additional rinses

in some programmes. On cotton pro-

grammes the maximum spin speed is re-

duced automatically.

EXTRA RINSE

This appliance is designed to save energy.

If it necessary to rinse the laundry using an

extra quantity of water (extra rinse), select

this option. Some additional rinses will be

performed. This option is recommended for

people who are allergic to detergents, and

in areas where the water is very soft.

6 electrolux

DELAY START

The programme can be delayed from 30

min - 60 min - 90 min, 2 hours and then by

1 hour up to a maximum of 20 hours by

means of this button.

START PAUSE

This button allows you to start or to inter-

rupt the selected programme.

TIME MANAGER

These buttons allows you to modify the

programme duration automatically pro-

posed by the appliance.

DISPLAY

7.1 7.3 7.5 7.6 7.7 7.8

7.9

7.107.117.12

7.2 7.4

The display shows the following informa-

tion:

7.1: Temperature value

7.2: Temperature icons

, Cold .

During the washing cycle the display shows

the temperature icon animated to indicate

that the appliance has started the heating

phase of the water in the tub.

7.3: Spin value

7.4: Spin speed icons.

•

No spin

•

Rinse Hold

•

Night Cycle

During the spinning phase the spiral is ani-

mated.

No spin option eliminates all the spin pha-

ses and increases the number of rinses for

some programmes.

Rinse Hold: by selecting this option the

water of the last rinse is not emptied out to

prevent the fabrics from creasing. When the

programme has finished the display shows

three blinking 0.00, the icon 7.10 is still vi-

sualized, the light of button 8 is off and the

door is locked to indicate that the water

must be emptied out. To empty out the wa-

ter, please read the paragraph «At the end

of the programme».

Night Cycle: by selecting this option, the

machine will not drain the water of the last

rinse, so as not to wrinkle the laundry. As all

spinning phases are suppressed, this

washing cycle is very noiseless and it can

be selectionned at night or in times with a

more economical power rate. On some

programmes the rinses will be performed

with more water. When the programme has

finished, the display shows three blinking

0.00, the icon 7.10 is still visualized, the

light of button 8 is off and the door is

locked to indicate that the water must be

emptied out. To empty out the water,

please read the paragraph «At the end of

the programme».

7.5: Option icons.

•

Extra Rinse

•

Easy Iron

•

Sensitive

(if available).

7.6: Child safety lock

(see «Personali-

sation» paragraph).

7.7: Soil degree icons

•

Intensive

electrolux 7

•

Normal/Daily

•

Light/Quick

•

Super Quick

7.8:

•

Duration of the selected programme

After selecting a programme, the duration

is displayed in hours and minutes (for ex-

ample 2.05). The duration is calculated

automatically on the basis of the maxi-

mum recommended load for each type of

fabric. After the programme has started,

the time remaining is updated every mi-

nute.

• End of programme

When the programme has finished three

flashing zeros is displayed, the icon 7.10

disappears and the door can be opened.

•

Incorrect option selection

If an option which is not compatible with

the set wash programme is selected, the

message Err is displayed at the bottom

of the display for a few seconds and the

integrated red light of button 8 start flash-

ing.

• Alarm codes

In the event of operating problems, some

alarm codes can be displayed, for exam-

ple E20 (see paragraph «What to do

if...»).

•

Delay Time value

7.9: Clock icon

After the programme has started, the dura-

tion is displayed and the clock icon is ani-

mated.

7.10: Door locked icon

After you have pressed button 8 and the

machine has started, this icon is lighted on

and only the phase running icon stays on.

When the programme has finished, three

flashing zero (0.00) are displayed and this

icon disappears.

7.11: Washing programme phase icons

•

Prewash

•

Wash

•

Rinses

•

Drain

•

Spin

By selecting the wash programme, the

washing programme phase icons corre-

sponding to the various phases making up

the programme are shown in the upper part

of the display. After having pressed button

8 only the icon of the running phase stays

on.

7.12: Delay icon

The selected delay set by pressing the rele-

vant button appears on the display for a

few seconds, then the duration of the previ-

ously selected programme is displayed. The

relevant icon is lighted on. The delay time

value decreases by one unit every hour and

then, when 1 hour remains, the time de-

creases every minute.

FIRST USE

• Ensure that the electrical and water

connections comply with the installa-

tion instructions.

• Remove the polystyrene block and

any material from the drum.

• Before the first wash, run a cotton

cycle at the highest temperature

without any laundry in the machine,

to remove any manufacturing residue

from the drum and tub. Pour 1/2 a

measure of detergent into the main

wash compartment and start the

machine.

PERSONALISATION

ACOUSTIC SIGNALS

The machine is provided with an acoustic

device, which sounds in the following ca-

ses:

• at the end of the cycle

• if there is a fault.

By pressing the 4 and 5 buttons simultane-

ously for about 6 seconds, the acoustic

signal is deactivated (except if there is a

fault). By pressing these 2 buttons again,

the acoustic signal is reactivated.

8 electrolux

CHILD SAFETY LOCK

This device permits you to leave the appli-

ance unattended and not to worry that chil-

dren might be injured by or cause damage

to the appliance. This function remains ena-

bled also when the washing machine is not

working.

There are two different ways to set this op-

tion:

1. Before pressing button 8: it will be im-

possible to start the machine.

2. After pressing button 8: it will be im-

possible to change any other pro-

gramme or option.

To enable or disable this option press si-

multaneously for about 6 seconds buttons

5 and 6 until on the display, the icon

ap-

pears or disappears.

DAILY USE

Load the laundry

Open the door by carefully pulling the door

handle outwards. Place the laundry in the

drum, one item at a time, shaking them out

as much as possible. Close the door.

Make sure that no laundry stays between

the seal and the door. There is a risk of wa-

ter leakage or damage to the laundry.

Measure out the detergent and the fab-

ric softener

Pull out the dispenser drawer until it stops.

Measure out the amount of detergent re-

quired, pour it into the main wash compart-

ment

or in the appropriate compartment

if the selected programme/option it requires

(see more details in «Detergent dispenser

drawer»).

If required, pour fabric softener into the

compartment marked

(the amount used

must not exceed the «MAX» mark in the

drawer). Close the drawer gently.

SELECT THE REQUIRED PROGRAMME

BY TURNING THE PROGRAMME

SELECTOR DIAL (1)

Turn the programme selector dial to the re-

quired programme. The washing machine

will propose a temperature and automati-

cally select the maximum spin value provi-

ded for the programme you have chosen.

You can change these values by operating

the corresponding buttons. The green pilot

light of the button 8 starts to flash.

The selector dial can be turned either clock-

wise or counterclockwise. Turn to position

to reset programme/Switching the ma-

chine off.

At the end of the programme the selec-

tor dial must be turned to position

to switch the machine off.

electrolux 9

Caution! If you turn the programme

selector dial to another programme

when the machine is working, the red

pilot light of button 8 will blink 3 times

and the message Err is displayed to

indicate a wrong selection. The

machine will not perform the new

selected programme.

SELECT THE TEMPERATURE BY

PRESSING BUTTON 2

By selecting a programme, the appliance

proposes automatically a default tempera-

ture.

Press this button repeatedly to increase or

decrease the temperature, if you want your

laundry to be washed at a different temper-

ature.

REDUCE THE SPIN SPEED BY

PRESSING BUTTON 3

By selecting a programme, the appliance

proposes automatically the maximum spin

speed provided for that programme.

Press button 3 repeatedly to change the

spin speed, if you want your laundry to be

spun at a different speed.

SELECT THE AVAILABLE OPTIONS BY

PRESSING BUTTONS 3, 4 AND 5

Depending on the programme, different

functions can be combined. These must be

selected after choosing the desired pro-

gramme and before pressing button 8.

When these buttons are pressed, the corre-

sponding icons appear on the display.

When they are pressed again, the icons

disappear. If an incorrect option is selected,

the integrated red pilot light of the button 8

flashes for 3 times and the Err message

appears on the display for a few seconds.

For the compatibility among the wash-

ing programmes and the options see

chapter «Washing Programmes».

SELECT THE DELAY START BY

PRESSING BUTTON 6

Before you start the programme, if you wish

to delay the start, press the button 6 re-

peatedly, to select the desired delay. The

corresponding icon 7.12 will appear on the

display in the upper part of the display.

The selected delay time value (up to 20

hours) will appear on the display a few sec-

onds, then the duration of the programme

will appear again.

You must select this option after you have

set the programme and before you press

button 8.

You can cancel or modify the delay time at

any moment, before you press button 8.

Selecting the delayed start:

1. Select the programme and the required

options.

2. Select the delay start by pressing the

button 6.

3. Press button 8:

– the machine starts its hourly count-

down.

– The programme will start after the

selected delay has expired.

Cancelling the delayed start after having

pressed button 8:

1. Set the washing machine to PAUSE by

pressing button 8.

Press button 6 once until the symbol

’ is displayed

3. Press button 8 again to start the pro-

gramme.

Important! The selected delay can be

changed only after selecting the washing

programme again.

The Delay Start can not be selected with

DRAIN programme.

START THE PROGRAMME BY

PRESSING BUTTON 8

To start the selected programme, press the

button 8, the green pilot light of the button

8 stops blinking. The icon 7.10 appears on

the display to indicate that the appliance

starts operating and the door is locked.

To interrupt a programme which is running,

press the button 8: the green pilot light

starts to blink.

To restart the programme from the point at

which it was interrupted, press the button 8

again. If you have chosen a delayed start,

the machine will begin the countdown.

If an incorrect option is selected, the red pi-

lot light of the button 8 blinks for 3 times

the message Err is displayed for few sec-

onds.

10 electrolux

SELECT THE TIME MANAGER OPTION

BY PRESSING BUTTONS 9

By pressing these buttons repeatedly, the

duration of the washing cycle can be in-

creased or decreased. The icon 7.7 will ap-

pear on the display to indicate the chosen

degree of soil. This option is available only

with Cotton, Synthetic and Delicate pro-

grammes.

Washing cy-

cle

Soil

Level

icon

Type of fabric

Intensive Heavy soiled items

Normal Normal soiled items

Daily Daily soiled items

Light Slightly soiled items

Quick Very slightly soiled

items

Super Quick

Items used or worn

for a short time

1) We recommend you to reduce the load sizes (see

Washing programmes table).

Important! The Time Manager cannot be

selected with the programmes

The availability of these soil level icons

change according to the type of fabric as

shown in the following chart.

Fabric Soil Level

Cottons

95°/90°C X X X X X X

60°C/50°C X X X X X X

40°C X X X X X X

30°C X X X X X X

Cold X X X X X X

Synthetics

60°C/50°C X X X X

40°C X X X X

30°C X X X X

Cold X X X X

Delicates

40°C X X X X

30°C X X X X

Cold X X X X

ALTERING AN OPTION OR A RUNNING

PROGRAMME

It is possible to change some options be-

fore the programme carries them out .

Before you make any change, you must

PAUSE the appliance by pressing the but-

ton 8 (if you wish to change the Time Man-

ager option, you must cancel the running

programme and make your selection

again).

Changing a running programme is possible

only by resetting it. Turn the programme se-

lector dial to

and then to the new pro-

gramme position. Start the new programme

by pressing the button 8 again. The wash-

ing water in the tub will be not emptied out.

INTERRUPTING A PROGRAMME

Press the button 8 to interrupt a pro-

gramme which is running, the correspond-

ing green pilot light starts blinking.

Press the button again to restart the pro-

gramme.

CANCELLING A PROGRAMME

Turn the selector dial to

to cancel a pro-

gramme which is running.

You can select now a new programme.

OPENING THE DOOR

After the programme has started (or during

the delay time) the door is locked, if you

need to open it, set first the machine to

PAUSE by pressing the button 8.

If the icon 7.10 after a few minutes disap-

pears from the display, the door can be

opened.

If the icon 7.10 does not go off, this means

that the machine is already heating or that

the water level is too high. Do not try to

force the door!

If you cannot open the door but you need

to open it you have to switch the machine

off by turning the selector dial to

. After a

few minutes the door can be opened (pay

attention to the water level and temper-

ature!).

After closing the door, it is necessary to se-

lect the programme and options again and

to press button 8.

electrolux 11

AT THE END OF THE PROGRAMME

The machine stops automatically. Three

blinking zeros (

) appear on the dis-

play. The pilot light of button 8 goes off.

Some acoustic signals sound for a few mi-

nutes.

If you set a programme or an option that

ends with water left in the tub, the icon 7.10

remains displayed. The door is still locked.

The water must be emptied out before

opening the door. During this time the drum

continues to turn at regular intervals until

water drain.

Follow the below instructions to empty out

the water:

Turn the programme selector dial to

2. Select the draining or spinning pro-

gramme.

3. Reduce the spin speed if needed, by

pressing the relevant button.

4. Press button 8.

At the end of the programme, after a few

minutes, the icon 7.10 disappears. The

door can be opened. Turn the programme

selector dial to

to switch the machine

off.

Remove the laundry from the drum and

carefully check that the drum is empty. If

you do not intend to carry out another

wash, close the water tap. Leave the door

open to prevent the formation of mildew

and unpleasant smells.

Stand by : once the programme has finish-

ed after a few minutes the energy saving

system will be enabled. The brightness of

the display is reduced. By pressing any but-

ton the appliance will come out of the ener-

gy saving status.

HELPFUL HINTS AND TIPS

SORTING OUT THE LAUNDRY

Follow the wash code symbols on each

garment label and the manufacturer’s

washing instructions. Sort the laundry as

follows: whites, coloureds, synthetics, deli-

cates, woollens.

TEMPERATURES

95° or 90°

for normally soiled white cot-

tons and linen (e.g. tea cloths,

towels, tablecloths, sheets...)

60°/50°

for normally soiled, colour fast

garments (e.g. shirts, night

dresses, pyjamas....) in linen,

cotton or synthetic fibres and

for lightly soiled white cotton

(e.g. underwear)

40°-30°-

Cold

for delicate items (e.g. net cur-

tains), mixed laundry including

synthetic fibres and woollens

bearing the label «pure new

wool, machine washable, non-

shrink»

BEFORE LOADING THE LAUNDRY

Never wash whites and coloureds together.

Whites may lose their «whiteness» in the

wash.

New coloured items may run in the first

wash; they should therefore be washed

separately the first time.

Make sure that no metal objects are

left in the laundry (e.g. hair clips, safety

pins, pins).

Button up pillowcases, close zip fasteners,

hooks and poppers. Tie any belts or long

tapes.

Remove persistent stains before washing.

Rub particularly soiled areas with a special

detergent or detergent paste.

Treat curtains with special care. Remove

hooks or tie them up in a bag or net.

MAXIMUM LOADS

Recommended loads are indicated in the

washing programme charts.

General rules:

• Cotton, linen: drum full but not too

tightly packed;

• Synthetics: drum no more than half full;

• Delicate fabrics and woollens: drum

no more than one third full.

Washing a maximum load makes the most

efficient use of water and energy.

For heavily soiled laundry, reduce the load

size.

12 electrolux

LAUNDRY WEIGHTS

The following weights are indicative:

bathrobe 1200 g

quilt cover 700 g

man’s work shirt 600 g

sheet, man’s pyjamas 500 g

tablecloth 250 g

pillow case, towelling towel,

night dress, man’s shirt

200 g

tea cloth, ladies’ briefs, nap-

kin, blouse, men’s under-

pants

100 g

REMOVING STAINS

Stubborn stains may not be removed by

just water and detergent. It is therefore ad-

visable to treat them prior to washing.

Blood: treat fresh stains with cold water.

For dried stains, soak overnight in water

with a special detergent then rub in the

soap and water.

Oil based paint: moisten with benzine

stain remover, lay the garment on a soft

cloth and dab the stain; treat several times.

Dried grease stains: moisten with turpen-

tine, lay the garment on a soft surface and

dab the stain with the fingertips and a cot-

ton cloth.

Rust: oxalic acid dissolved in hot water or a

rust removing product used cold. Be careful

with rust stains which are not recent since

the cellulose structure will already have

been damaged and the fabric tends to hole.

Mould stains: treat with bleach, rinse well

(whites and fast coloureds only).

Grass: soap lightly and treat with bleach

(whites and fast coloureds only).

Ball point pen and glue: moisten with

acetone

, lay the garment on a soft cloth

and dab the stain.

Lipstick: moisten with acetone as above,

then treat stains with methylated spirits.

Treat any residual marks with bleach.

Red wine: soak in water and detergent,

rinse and treat with acetic or citric acid,

then rinse. Treat any residual marks with

bleach.

Ink: depending on the type of ink, moisten

the fabric first with acetone

, then with

acetic acid; treat any residual marks on

white fabrics with bleach and then rinse

thoroughly.

Tar stains: first treat with stain remover,

methylated spirits or benzine, then rub with

detergent paste.

DETERGENTS AND ADDITIVES

Good washing results also depend on the

choice of detergent and use of the correct

quantities to avoid waste and protect the

environment.

Although biodegradable, detergents contain

substances which, in large quantities, can

upset the delicate balance of nature.

The choice of detergent will depend on the

type of fabric (delicates, woollens, cottons,

etc.), the colour, washing temperature and

degree of soiling.

All commonly available washing machine

detergents may be used in this appliance:

• powder detergents for all types of fabric

• powder detergents for delicate fabrics

(60°C max) and woollens

• liquid detergents, preferably for low tem-

perature wash programmes (60°C max)

for all types of fabric, or special for wool-

lens only.

The detergent and any additives must be

placed in the appropriate compartments of

the dispenser drawer before starting the

wash programme.

If using liquid detergents, a programme

without prewash must be selected.

Your appliance incorporates a recirculation

system which allows an optimal use of the

concentrated detergent.

Follow the product manufacturer’s recom-

mendations on quantities to use and do

not exceed the «MAX» mark in the de-

tergent dispenser drawer.

DEGREES OF WATER HARDNESS

Water hardness is classified in so-called

“degrees” of hardness. Information on hard-

ness of the water in your area can be ob-

tained from the relevant water supply com-

pany, or from your local authority.

1) do not use acetone on artificial silk

electrolux 13

A water softener must be added when

water has a medium-high degree of

hardness (from degree of hardness II).

Follow the manufacturer’s instructions.

The quantity of detergent can then al-

ways be adjusted to degree of hard-

ness I (= soft).

Level

Charac-

teristic

Degrees of water

hardness

German

°dH

French

°T.H.

1 soft 0-7 0-15

Level

Charac-

teristic

Degrees of water

hardness

German

°dH

French

°T.H.

2 medium 8-14 16-25

3 hard 15-21 26-37

4 very hard > 21 > 37

WASHING PROGRAMMES

Programme

Maximum and Minimum Temperature

Cycle Description

Maximum Spin Speed

Maximum Fabrics Load

Type of Laundry

Options

Detergent Com-

partment

Cottons

90° - Cold

Main wash - Rinses

Maximum spin speed 1400 rpm

Max. load 7 kg - Red. load 3 kg

White and coloured cotton (normally soiled items).

SPIN REDUCTION

RINSE HOLD

NO SPIN

NIGHT CYCLE

EASY IRON

EXTRA RINSE

TIME MANAGER

Cottons + Prewash

90° - Cold

Prewash - Main wash - Rinses

Maximum spin speed 1400 rpm

Max. load 7 kg - Red. load 3 kg

White or coloured cottons with prewash phase

(heavily soiled items).

SPIN REDUCTION

RINSE HOLD

NO SPIN

NIGHT CYCLE

EASY IRON

EXTRA RINSE

TIME MANAGER

Synthetics

60° - Cold

Main wash - Rinses

Maximum spin speed 900 rpm

Max. load 3 kg - Red. load 1.5 kg

Synthetic or mixed fabrics normally soiled items.

SPIN REDUCTION

RINSE HOLD

NO SPIN

NIGHT CYCLE

EASY IRON

EXTRA RINSE

TIME MANAGER

Synthetics + Prewash

60° - Cold

Prewash - Main wash - Rinses

Maximum spin speed 900 rpm

Max. load 3 kg - Red. load 1.5 kg

Synthetic or mixed fabrics with prewash phase

(heavily soiled items).

SPIN REDUCTION

RINSE HOLD

NO SPIN

NIGHT CYCLE

EASY IRON

EXTRA RINSE

TIME MANAGER

14 electrolux

Programme

Maximum and Minimum Temperature

Cycle Description

Maximum Spin Speed

Maximum Fabrics Load

Type of Laundry

Options

Detergent Com-

partment

Delicates

40° - Cold

Main wash - Rinses

Maximum spin speed 700 rpm

Max. load kg 3 - Red. load kg 1.5

Delicate fabrics normally soiled delicate items.

SPIN REDUCTION

RINSE HOLD

NO SPIN

NIGHT CYCLE

EXTRA RINSE

TIME MANAGER

Spin

Drain and long spin

Maximum spin speed 1400 rpm

Max. load 7 kg

Separate spin for hand washed garments and after

programmes with the Rinse Hold or Night cycle option

selected. You can choose the spin speed by pressing

the relevant button to adapt it to the fabrics to be

spun.

SPIN REDUCTION

Drain

Draining of water

Max. load 7 kg

For emptying out the water of the last rinse in pro-

grammes with the Rinse Hold or Night cycle option

selected.

Rinses

Maximum spin speed 1400 rpm

Max. load 7 kg

With this programme it is possible to rinse and spin

cotton garments which have been washed by hand.

The machine performs 3 rinses, followed by a final

long spin. The spin speed can be reduced.

SPIN REDUCTION

RINSE HOLD

NO SPIN

NIGHT CYCLE

EXTRA RINSE

EASY IRON

Mix 20°

20°

Main wash - Rinses - Spin

Maximum spin speed 900 rpm

Max. load 3 kg

Special programme for cotton, synthetic and mixed

fabrics with light soil.

Set this programme to decrease the energy con-

sumption.

Make sure that the detergent is for low temperature in

order to have good washing results.

SPIN REDUCTION

RINSE HOLD

EXTRA RINSE

Silk

30° - Cold

Main wash - Rinses

Maximum spin speed 700 rpm

Max. load 1 kg

Delicate washing programme suitable for silk and

mixed synthetic items.

SPIN REDUCTION

RINSE HOLD

NO SPIN

NIGHT CYCLE

electrolux 15

Programme

Maximum and Minimum Temperature

Cycle Description

Maximum Spin Speed

Maximum Fabrics Load

Type of Laundry

Options

Detergent Com-

partment

Handwash

40° - Cold

Main wash - Rinses

Maximum spin speed 1000 rpm

Max. load 2 kg

Special programme for delicate fabrics with «hand

washing» care symbol.

SPIN REDUCTION

RINSE HOLD

NO SPIN

NIGHT CYCLE

Wool

40° - Cold

Main wash - Rinses

Maximum spin speed 1000 rpm

Max. load 2 kg

Washing programme for machine washable wool as

well as for hand washable woollens and delicate fab-

rics. Note: A single or bulky item may cause imbal-

ance. If the appliance doesn’t perform the final spin

phase, add more items, redistribute the load manually

and then select the spinning programme.

SPIN REDUCTION

RINSE HOLD

NO SPIN

NIGHT CYCLE

Cottons Eco + Prewash

90 °- 40°

Prewash - Main wash - Rinses

Maximum spin speed 1400 rpm

Max. load 7 kg

White or coloured cottons with prewash phase.

This programme can be selected for normally soiled

cotton items with stains. The temperature will de-

crease and the washing time will be extended.

SPIN REDUCTION

RINSE HOLD

NO SPIN

NIGHT CYCLE

EASY IRON

EXTRA RINSE

Cottons Eco

90° - 40°

Main wash - Rinses

Maximum spin speed 1400 rpm

Max. load 7 kg

White and fast coloured cotton.

This programme can be selected for slightly or nor-

mally soiled cotton items. The temperature will de-

crease and the washing time will be extended. This al-

lows to obtain a good washing efficiency so saving

energy.

SPIN REDUCTION

RINSE HOLD

NO SPIN

NIGHT CYCLE

EASY IRON

EXTRA RINSE

= OFF

For cancelling the programme which is running or to

switch the machine off .

1) If you select the Super Quick option by pressing button 9, we recommend that you reduce the maximum load as

indicated. (Red. load = reduced load). Full loading is possible however with somewhat reduced cleaning results.

2) If using liquid detergents, a programme without PREWASH must be selected.

3) The appliance performs the short heating phase if the water temperature is below 20°C. The appliance can show

the temperature setting as “cold”.

4) STANDARD PROGRAMMES for the Energy Label consumption values. According to regulation 1061/2010,

these programmes are respectively the «standard 60° C cotton programme» and the «standard 40° C cotton

programme». They are the most efficient programmes in terms of combined energy and water consumption for

washing normally soiled cotton laundry.

16 electrolux

Set this programme to have a good washing results and decrease the energy consumption. The time of the

washing programme is extended.

The washing temperature of the washing phase may differ from the temperature declared for the set pro-

gramme.

CONSUMPTION VALUES

The data of this table are approximate. Different causes can change the data: the

quantity and type of laundry, the water and ambient temperature.

Programmes Load

(kg)

Energy con-

sumption

(kWh)

Water con-

sumption (li-

tre)

Approximate

programme

duration (mi-

nutes)

Remaining

moisture

(%)

Cottons 60 °C 7 1.2 53 140 52

Cottons 40 °C 7 0.7 53 130 52

Synthetics 40 °C 3 0.5 40 80 35

Delicates 40 °C 3 0.55 55 65 35

Wool/Hand wash

30 °C

2 0.25 58 50 30

Standard cotton programmes

Standard 60 °C

cotton

0.84

191

Standard 60 °C

cotton

3.5 0.77 36

172

Standard 40 °C

cotton

3.5

0.50

38 160 52

1) At the end of spin phase.

Off Mode (W) Left On Mode (W)

0.10 0.98

The information given in the charts above are in compliance with the EU Commission regulation

1015/2010 implementing directive 2009/125/EC.

CARE AND CLEANING

Warning! You must disconnect the

appliance from the electricity supply,

before you can carry out any cleaning

or maintenance work.

DESCALING

The water we use normally contains lime. It

is a good idea to periodically use a water

softening powder in the machine. Do this

separately from any laundry washing, and

according to the softening powder manu-

facturer's instructions. This will help to pre-

vent the formation of lime deposits.

AFTER EACH WASH

Leave the door open for a while. This helps

to prevent mould and stagnant smells form-

ing inside the appliance. Keeping the door

open after a wash will also help to preserve

the door seal.

MAINTENANCE WASH

With the use of low temperature washes it

is possible to get a build up of residues in-

side the drum.

We recommend that a maintenance wash

be performed on a regular basis.

To run a maintenance wash:

electrolux 17

• The drum should be empty of laundry.

• Select the hottest cotton wash pro-

gramme.

• Use a normal measure of detergent,

must be a powder with biological proper-

ties.

EXTERNAL CLEANING

Clean the exterior cabinet of the appliance

with soap and water only, and then dry

thoroughly.

Important! Do not use methylated spirits,

solvents or similar products to clean the

cabinet.

CLEANING THE DISPENSER DRAWER

The detergent dispenser drawer should be

cleaned regularly.

The washing powder and additive dispens-

er drawer should be cleaned regularly.

Remove the drawer by pressing the catch

downwards and by pulling it out.

Flush it out under a tap, to remove any

traces of accumulated powder.

To aid cleaning, the top part of the additive

compartment should be removed. Clean all

parts with water.

Clean the chamber of dispenser drawer

with a brush.

WASHING DRUM

Rust deposits in the drum may occur due

to rusting foreign bodies in the washing or

tap water containing iron.

Important! Do not clean the drum with

acidic descaling agents, scouring agents

containing chlorine or iron or steel wool.

1. Remove any rust deposits on the drum

with a cleaning agent for stainless steel.

2. Run a washing cycle without any wash-

ing to clean off any cleaning agent resi-

dues.

Programme: Short Cotton Programme

at maximum temperature and add ap-

prox. 1/4 measuring cup of detergent.

DOOR SEAL

Check from time to time the door seal and

eliminate eventual possible objects that

could be trapped in the fold.

DRAIN PUMP

The pump should be inspected regularly

and particularly if:

• the appliance does not empty and/or

spin;

• the appliance makes an unusual noise

during draining due to objects such as

safety pins, coins etc. blocking the

pump;

• a problem with water draining is detected

(see chapter “What to do if...” for more

details).

18 electrolux

Warning! Before unscrewing the pump

cover, switch the appliance off and

remove the mains plug from the

socket.

Proceed as follows:

1. Unplug the appliance.

2. If it is necessary, wait until the water

has cooled down.

3. Place a container close to the pump to

collect any spillage.

4. Release the emergency emptying hose

(B), place it in the container and re-

move its cap cover

5. When no more water comes out, un-

screw the pump cover (A) by turning it

anti-clockwise and remove the filter.

Use pliers, if necessary. Always keep a

rag nearby to dry up any water spill-

ages when removing the cover.

Clean the filter under a tap, to remove

any traces of fluff.

6. Remove foreign bodies and fluff from

the filter seat and from the pump impel-

ler.

Check carefully whether the pump im-

peller rotates (it rotates jerkily). If it

doesn’t rotate, please contact your

Service Centre.

7. Put the cap back on the emergency

emptying hose and place the latter

back in its seat.

8. Replace the filter into the pump by in-

serting it correctly into the special

guides. Screw the pump cover firmly by

turning it clockwise.

Warning!

When the appliance is in use and depend-

ing on the programme selected there can

be hot water in the pump.

electrolux 19

Never remove the pump cover during a

wash cycle, always wait until the appliance

has finished the cycle, and is empty. When

refitting the pump cover, ensure it is se-

curely retightened so as to stop leaks and

young children being able to remove it.

CLEANING THE WATER INLET

FILTERS

If you notice that the machine is taking lon-

ger to fill, check that the filter in the water

inlet hose is not blocked.

1. Turn off the water tap.

2. Unscrew the water inlet hose.

3. Clean the filter in the hose using a hard

bristle brush.

4. Screw the hose back onto the tap.

5. Un

screw the hose from the machine.

Keep a rug nearby because some wa-

ter may flow.

6. Clean the filter in the valve with a stiff

brush or with the piece of cloth.

7. Screw the hose back to the machine

and make sure the connection is tight.

8. Turn on the water tap.

FROST PRECAUTIONS

If the machine is installed in a place where

the temperature could drop below 0°C,

proceed as follows:

1. Turn off the water tap.

2. Unscrew the inlet hose.

3. Place the end of the emergency empty-

ing hose and that of the inlet hose in a

bowl placed on the floor and let water

drain out.

4. Screw the water inlet hose back on and

reposition the emergency emptying

hose after having put the cap on again.

5. When you intend to start the machine

up again, make sure that the room

temperature is above 0°C.

EMERGENCY EMPTYING OUT

If the water is not discharged, proceed as

follows to empty out the machine:

1. pull out the plug from the power sock-

et;

2. close the water tap;

3. if necessary, wait until the water has

cooled down;

4. place a bowl on the floor and place the

end of the emergency emptying hose

into the bowl. Remove its cap. The wa-

ter should drain by gravity into the

bowl. When the bowl is full, put the cap

back on the hose. Empty the bowl. Re-

peat the procedure until water stops

flowing out;

5. clean the pump if necessary as previ-

ously described;

6. replace the emergency emptying hose

in its seat after having plugged it;

7. screw the pump again.

Important! Every time you drain the water

through the emergency emptying hose you

must pour 2 litres of water into the main

wash compartment of the detergent drawer

and then run the drain programme. This will

activate the ECO Valve device avoiding

that part of the detergent remains unused

at next washing.

WHAT TO DO IF…

Certain problems are due to lack of simple

maintenance or oversights, which can be

solved easily without calling out an engi-

neer. Before contacting your local Service

20 electrolux

Page is loading ...

Electrolux EWG147540W User manual

Brand: Electrolux

Model: EWG147540W

Category: Washing machines

Type: User manual

Download PDF

report

Electrolux EWG147540W User manual

Electrolux EWG147540W User manual

Related papers

Other documents