EN
Read the Instructions for Use carefully before
using the appliance.
SMART DISPLAY
This optional function can be used to save energy. To activate /deactivate
the Smart Display, press and hold Fast Cool and Vacation buttons at
the same time for 3 seconds until an audible signal sounds. To temporary
reactivate the display, press any button. Remember that this function does not
disconnect the appliance from the power supply, but only reduce the power
consumed by external display (see the Instructions for Use).
19514529000
QUICK START GUIDE
CS GBBG
Printed in Italy 04/16 - Whirlpool
®
Registered trademark/TM Trademark of Whirlpool group of companies - © Copyright Whirlpool Europe s.r.l. 2015. All rights reserved - http://www.whirlpool.eu
ON/STANDBY
To put the product in Stand-by, press and hold the button for 3 seconds.
All the icons turn off except On/Standby indicator
. To reactivate the
appliance press once (briefly) this button. (see the Instructions for Use)
FAN
The Fan improves temperature distribution inside the product, allowing better
preservation of stored food. By default, the fan is switched on and the Fan
symbol is visible on control panel.
To switch off the Fan press and hold Fast Cool
and ON/Standby
buttons at the same time for 3 seconds until an audible signal sounds and Fan
icon will turn off as confirmation that the fan has been switched off.
To switch on the Fan, repeat the same procedure. As a confirmation audible
signal sounds turns on and the Fan symbol turns on.
Note: Reasons why switch off the fan look for “ENERGY-SAVING TIPS” in the
Instructions for Use.
FAST COOL button
Using Fast Cool function it is possible to increase the cooling capacity in the
refrigerator compartment. The use of this function is recommended when
placing a very high quantity of food in the refrigerator compartment. Press the
Fast Cool button to activate Fast Cool function. When activated, the Fast
Cool indicator turns on. The function is automatically disabled after 6 hours, or
can be manually disabled by pressing Fast Cool button again.
ALARMS TABLE
ALARM TYPE Signal Cause Cure
Door open alarm
The acoustical alarm is activated. The Alarm Indicator
blinks and the Door
Open Alarm indicator still visible until the door is closed
(even if other alarms have been reset)
The door has remained open for more than 2 minutes. Close the door or press the Stop Alarm to mute the acoustical alarm.
Malfunction. The letter “F” blinks on the display (°C). Product malfunction. Contact the After-sales Service.
1
2
5
6
7
9
10
13
16
17
8
11
X
3
4
18
15
X
12
1. Control panel
2. Main LED ‘s lighting*
3. Fan
4. Optional lighting in Multi-flow*
5. Shelf divider*
6. Multi-flow cold air area*
7. Bottle rack *
8. Sensor cover
9. Rating plate with commercial name
10. Cooler compartment(best for meat and fish)*
11. Area shelves
12. Fruits and vegetables crisper
13. Crisper divider*
14. Door reversibility kit*
15. Egg tray*
16. Bottle separator*
17. Door trays
18. Door seal
* Available on selected models
HOW TO START THE APPLIANCE
After plugging the appliance to the mains, it starts the
operation automatically. After starting the appliance,
wait at least 4-6 hours before placing food into the
appliance. When the appliance is connected to the
power supply, the display lights up and all the icons
appear on the display for approximately 1 second.
The default (factory) values of the fridge compartment
settings light-up.
HOW TO REVERSE THE DOOR SWING
- see enclosed Instructions for Use (Version_1)
Is recommended to reverse door swing by two
persons. There is not foreseen door reversibility for:
- models with integrated handle
- models with glass panel on the door.
Specifications, technical data and images may
vary from model.
To receive the assistance call the number shown on
the warranty booklet or follow the instruction on the
web site www.hotpoint.eu
VACATION button
This function can be activated to reduce the energy consumption of
the appliance during a prolonged period of time.
Before activating the feature, all perishable food should be removed
from the refrigeration compartment and make sure that the door
is closed properly, since the refrigerator will maintain a suitable
temperature to prevent the formation of unpleasant odors (+12°C).
To activate/ deactivate press the Vacation mode button for 3
seconds. When the function is enabled, the related symbol will
light up and the temperature of the refrigerator compartment will be
set to a higher setpoint (the temperature display will show the new
temperature setpoint of +12°C). Changing the temperature setpoint
will automatically deactivate the function.
TEMPERATURE DISPLAY
KKHU
TEMPERATURE button
Press the temperature button to change the temperature:
the value changes cyclically between 8°C ad 2°C.
Note: Displayed set points correspond to the average
temperature throughout the whole refrigerator.
DOOR OPEN ALARM indicator
(see the below alarms table)
ALARM indicator
(see the below Alarms Table)
STOP ALARM button
Press in case of alarm to mute the acoustic alarm.
UKSKRUROPL
1
