Magnadyne Stereo Receiver M5100CD User manual

Brand: Magnadyne

Model: Stereo Receiver M5100CD

Category: Car media receivers

Type: User manual

This manual is also suitable for

Installation and

Operation Manual

M5100CD

Waterproof

AM/FM/WB and CD Stereo Receiver

EJECT

ELAPSE

SHIFT

POWER

MARINE CD RECEIVER

PULL OPEN

4 X 50W

DISPBAND

MONO

TRK

TUNE

MUTE

5 INT4 RDM3 RPT2 PGM1 MEM

TRK

TUNE

SEL

LOUD

DIM

MODE

AS/PS

SCAN

SHIFT

PGM

A Registered Trademark of Magnadyne Corporation

US Patent Number D 500,303 S

M5100CDUMFinal 2/1/05 4:58 PM Page 1

Location and Function of Controls at a Glance

56 7 8 9 10

18192021

2223

11 1312

EJECT

ELAPSE

SHIFT

POWER

MARINE CD RECEIVER

PULL OPEN

4 X 50W

DISPBAND

MONO

TRK

TUNE

MUTE

5 INT4 RDM3 RPT2 PGM1 MEM

TRK

TUNE

SEL

LOUD

DIM

MODE

AS/PS

SCAN

SHIFT

PGM

Your new M5100CD entertainment system has been designed to give you many years of listening pleasure.

Take a moment to read through this manual and become familiar with the operations and features of this

outstanding product.

It is advisable to keep this manual in your vehicle so it is readily available for reference. Be sure to fill out

and send in your warranty card to ensure that you receive the full benefits of warranty repair in the unlikely

event that your system will need service. We are confident that you will thoroughly enjoy your new mobile

entertainment system.

Introduction

1. Power: Turns the unit On/Off.

2. Dimmer/Loud Button:

Loud Button: Enhances high frequency and low frequency sound quality.

Dimmer Button: Press and hold this button to change the brightness of the LCD display backlight.

3. Mode Button: Changes sequentially through the following sources:

Radio Tuner > CD > CD Changer (optional) > Auxiliary > Radio Tuner.

4. Volume Buttons: Adjusts the Volume, Bass, Treble, Balance and Fader.

5. Track/Tune Up and Down Buttons: Adjusts the radio frequency, sets the clock, and changes CD tracks.

6. Multi-Function Button 1/MEM:

Radio:

Recalls a memorized radio station, and programs a radio station into memory

(See Radio Operation for more information).

CD: Programs a CD track into memory (See CD Operation for more information).

7. Multi-Function Button 2/PGM:

Radio: Recalls a memorized radio station, and programs a radio station into memory

(See Radio Operation for more information).

CD: Enters CD track program mode (See CD Operation for more information).

M5100CDUMFinal 2/1/05 4:58 PM Page 2

8. Multi-Function Button 3/RPT:

Radio:

Recalls a memorized radio station, and programs a radio station into memory

(See Radio Operation for more information).

D: Continuously repeats the same track (See CD Operation for more information).

9. Multi-Function Button 4/RDM:

Radio: Recalls a memorized radio station, and programs a radio station into memory

(See Radio Operation for more information).

Plays all tracks on the current disc in random order (See CD Operation for more information).

10. Multi-Function Button 5/INT:

Radio: Recalls a memorized radio station, and programs a radio station into memory

(See Radio Operation for more information).

Plays the first several seconds of each track on the current disc

(See CD Operation for more information).

11. Band Button: Selects the radio band in the following order: FM1, FM2, FM3, AM, WX.

12. Mono Button: Changes FM radio reception from Mono to Stereo.

13. Display Button: Displays either the clock or radio frequency. (See setting the clock for more

information).

14. EQ Button: Selects preprogrammed equalizer settings in the following order: POP (Pop), JAZ (Jazz),

CLA (Classical), JAM (Jam), ROC (Rock) and FLA (Flat).

15. Shift and Scan Button:

Shift Button: Enables the unit to scroll through the CD's (using Track/Tune Up and Down Buttons)

when a CD Changer is connected.

Scan Button

Scans through the strong stations in the current radio band.

16. Elapse and AS/PS Button:

Radio: Automatic memory storing and preset scan (See Radio operation for more information).

Displays elapsed time of current CD track or time remaining on the current CD.

17. Eject Button: Ejects the disc from the CD slot when the CD door is open.

18. Play/Pause and Mute Button:

Radio/Aux In:

Mutes audio level.

Starts CD play function or pauses CD play function.

19. CD Slot: Located behind the Waterproof CD Cover; insert discs here.

20. Display Area: Displays Radio, CD and Clock functions.

21. Reset Button: Resets control logic of CPU in the event of a lockup. See General Operations/Reset

button for more details.

22. Waterproof CD Cover: To access the CD Slot, press down the tab on the top of the cover.

23. Audio Mode Selection Button: Selects the desired audio mode in the following order: Volume, Bass,

Treble, Balance and Fader.

Location and Function of Controls at a Glance

M5100CDUMFinal 2/1/05 4:58 PM Page 3

Radio Operation

Listening to the Radio

Push the “POWER” button (1) once to turn the unit on.

2. Press the “BAND” button (11) to select a radio

band: FM1, FM2, FM3, AM or WX (weather band).

3. AM or FM Station Selection

Automatic Seek Station Selection: Press the

TRK/TUNE DN or TRK/TUNE UP button (5) to

automatically seek the next strong station.

Scan Station Selection: Press the button

(15) to automatically scan through strong

stations in the current radio band. The radio

will pause for 5 seconds at each strong station.

Each frequency will flash in the display. Press

the scan button again to hold the current station.

Manual Station Selection: Press the TRK/TUNE

DN or TRK/TUNE UP button for more than 3

seconds to manually select stations, and “MAN”

will appear in the display. Use either button to

manually seek up and down the frequency scale.

Note: If either button is not pressed for several

seconds, the unit will return to Automatic Seek

“AUTO” will appear in the display.

Weather Band Station Selection (WX)

Press the “BAND” button until WX appears on

the display, then use the TRK/TUNE DN or

TRK/TUNE UP button to manually seek the stations.

SHIFT

SCAN

Sound Controls

Programming the Radio

You can program up to 15 FM radio stations and 5 AM

radio stations.

Manual Station Recall Programming

Press the “BAND” button (11) to select a radio

band: FM1, FM2, FM3 or AM.

2. Select the desired station.

3. Press and hold one of the five station recall buttons

(6-10), the button number and “CH” will appears in

the display area. Release the button.

4. Repeat the Steps 1-3 to memorize additional

stations as desired.

Automatic Station Store

Press the “BAND” button (11) to select a radio

band: FM1, FM2, FM3 or AM.

2. Press the button (16) for more than 2

seconds, the radio will then search the current

frequency and check the signal strength until the

five

strongest stations are stored into the correspond-

ing preset number button. When completed, the

system will scan the stored stations automatically.

Preset Scan

Press the button (16) to scan the preset

stations. The radio will hold at that preset number

for several seconds, then will scan again. To stop

scanning when a desired station is reached press

the button again.

Adjusting the Main Volume, Bass Treble, Balance

and Fader.

1. Press the button (23) to select the desired

audio mode. The audio modes will be displayed in

the following order: Volume, Bass, Treble,

Balance and Fader.

2. Press the Main Volume or buttons (4) to

adjust the sound of the audio mode selected.

Note: The Bass and Treble levels can only be adjusted

when the EQ setting is set to the “FLAT” setting.

Initial Volume Level

To program the Initial Volume Level, adjust the

volume to the desired level, then press the

“POWER” button for more than 3 seconds. The

next time the unit is turned on, the volume will be

at this initial level.

Adjusting the Audio Beep

Press the button for more then 2 seconds

to turn beep On/Off. When the beep is on the

icon will be displayed.

Adjusting the Loud Feature

Press the LOUD button (2) to increase the bass

and treble output, “LOUD” will then be displayed.

Press the button again to release this function.

Mute

In Radio/Aux In mode, press the button (18)

mute audio level. Press the button again to

release this function.

SEL

AS/PS

ELAPSE

AS/PS

M5100CDUMFinal 2/1/05 4:58 PM Page 4

Select a Disc

1. Load your CD Changer with compact discs per

the manufacturer's operating instructions.

2. Press the SHIFT button (15) to enter Shift

Mode. “SHIFT” will then appear in the display,

indicating the CD Changer is active.

3. Press the TRK/TUNE DN or TRK/TUNE UP (5)

button to scroll through the CD’s loaded in the CD

Changer. If there isn’t any operation for several

seconds, the unit will exit Shift Mode automatically.

Notes on CD-Rs and CD-RWs:

•

The unit cannot play a CD-R and CD-RW that is

not finalized. (Please refer to the manual of your

CD-R/CD-RW recorder or CD-R/CD-RW software

for more information on the finalizing process).

• This unit will not play MP3 music or WMA music

recorded on any CD-R or CD-RW disc.

• Be sure to only use discs with the following labels

in this unit:

General Operations

Setting the Clock

1. Press DISP button (13) for more than 3 seconds

until the clock shown in the display area is flashing.

2. Press the TRK/TUNE DN button to adjust the

hours

3. Press the TRK/TUNE UP button to adjust the

minutes.

Display Priority

Clock Display Priority

Press and hold DISP button (13) while pressing

the TRK/TUNE DN button to select Time Priority.

Pressing the DISP button while in Time Priority

will temporarily display selected station frequency.

In CD Mode:

When the display priority is set to “Time”, the

time will be displayed.

Pressing DISP button will temporarily display CD

track number, time remaining or elapsed time

depending on current CD display option selected.

After 5 seconds the display will return to the clock.

Frequency Display Priority

Press and hold DISP button while pressing the

TRK/TUNE UP button to select Frequency

Priority. Pressing DISP button while in Frequency

Priority will temporarily display clock.

In CD Mode:

When the display priority is set to “Frequency”,

the CD track number will be displayed.

Pressing the DISP button will temporarily display

the clock. After 5 seconds the display will return

to the CD display.

Selecting a Mode

Press the MODE button (3) to step sequentially

through the following sources: Radio Mode to

Radio Tuner > CD > CD Changer (optional) >

Auxiliary > Radio Tuner.

Illumination Dimmer

Press LOUD/DIMMER button (2) for more than 2

seconds to adjust the brightness of the LCD

display backlight.

Reset Button (20)

The Reset Button (21) is located behind the

Waterproof CD Cover (22) and above the CD Slot.

Activate the reset button with either a ballpoint

pen tip or paper clip for the following reasons:

• After initial installation of the unit is completed.

• When the function buttons do not operate.

• Error symbol in the display.

If there is a disc in the slot when the reset button

is pressed the disc will be ejected.

CD Changer Operation (Optional)

SCAN

M5100CDUMFinal 2/1/05 4:58 PM Page 5

Inserting and Ejecting a Disc

Pull the tab at the top of the CD Door, and the

door will open. Push a disc into the CD Slot (19),

label side up, and the disc will begin to play.

The disc will eject automatically when the CD

Door is opened.

Select Tracks

Press the TRK/TUNE DN or TRK/TUNE UP button

(5) to move to the previous track or next track.

The track number appears in the Display Area.

Fast Forward and Fast Reverse

Press and hold the TRK/TUNE DN or TRK/TUNE

UP button (5) to fast forward or fast reverse. Disc

play starts from when you release the button.

Pause Disc Play

Press the button (18) to pause the CD player.

Press it again to resume play.

Repeat the Same Track

Press the button (8) to continuously

repeat the same track. Press it again to stop

repeat.

Play All Tracks in Random Order

Press the button (9) to play all tracks

on the current disc in random order. Press it

again to stop random play.

Intro Scan

Press the button (10) to play the first 10

seconds of each track. Press it again to cancel the

function and listen to the track.

Program CD Tracks

Use the Program function to select up to 32 CD

tracks to play in any order. The Program function

allows you to select a track number for each spot

in the playing sequence. A CD must be inserted to

use the Program function.

1. Press the button (7) to enter Program

mode. PGM starts flashing and the “P-01”

appears in the display.

2. Press the TRK/TUNE DN or TRK/TUNE UP button

to choose a track number. Then press the

button (7) to memorize it. Select the next

track and it will memorized as “P-02”.

Repeat these steps to program tracks in the

desired order. Then press the button to

play the CD in programmed order. When you

have programmed 32 tracks, “FULL” will appear

in the display.

• When the CD is played in programmed order,

press the button to begin programmed

play, then press it again to exit the PGM mode.

• When the CD is playing in programmed order,

pressing the button will clear all the pro-

grammed content and “CLR” will appear in the

display.

• If you don’t press the button (7) to carry

out program setting, press the button

(8), “NO-P” will appear in the display.

Track/Time Display

To display the running time/remaining time of a

track, press the ELAPSE button (16).

CD Player Operation

3 RPT

5 INT

1 MEM

2 PGM

1 MEM

2 PGM

AS/PS

1 MEM

4 RDM

M5100CDUMFinal 2/1/05 4:58 PM Page 6

Waterproof Wired Remote General Operations (Optional)

1. Power Button: Press and release the POWER

button (1) to turn on/off the unit.

To program the initial volume level, adjust the

volume to the desired level, then press the

POWER button for more than 3 seconds. The

next time the unit is turned on, the volume will be

at this initial level.

2. Band Button: Press the BAND button (2) to

sequentially step through the following bands:

FM1, FM2, FM3, AM and WX.

3. Shift/Scan Button:

For Radio Operation

Press the SHIFT/SCAN button (3) to scan through

the strong stations in the current radio band. The

radio will pause for five seconds at each strong

station while flashing the frequency, then will con-

tinue to scan. Pressing the SHIFT/SCAN button

again will stop the scanning, and play the current

station.

For CD Changer (CDC) Operation

Press the SHIFT/SCAN button (3) to enter Shift

Mode. “SHIFT” will then appear in the display,

indicating the CD Changer is active. To change

the current CD, press the TRK/TUNE DN or

TRK/TUNE UP button (5) to scroll through the

CDs loaded in the CD Changer. If there isn’t any

operation for several seconds, the unit will exit

Shift Mode automatically.

4. Mute Button:

For Radio Operation

Press the button (4) to activate the audio

mute function and “MUTE” will appear in the dis-

play. Press the button once again to release mute

function and the unit will return to the last vol-

ume position before it was muted.

For CD/CD Changer Operation

Press the button (4) to pause the CD/CDC

player. Press it again to resume play.

5. Volume Buttons: Press the button to in-

crease or the button decrease the volume

level.

6. Manual/Search Tuning and Track Selection

Buttons:

For Radio Station Selection

• Press and release the TRK/TUNE DN or

TRK/TUNE UP button (6) to search up or down

to the next strong station. Continue to press

and release the buttons until the desired station

is located.

• Press and hold the TRK/TUNE DN or TRK/TUNE

UP button for more than 3 seconds to activate

Manual Tuning Mode (MAN will appear in the

display). In Manual Tuning Mode you can

quickly advance up or down the radio station

scale by pressing and holding down the

TRK/TUNE DN or TRK/TUNE UP buttons (6).

• After several seconds of non-use, the button

(6) tuning function will revert back to Search

Mode (AUTO will appear in the display).

Station Selection for Weather Band Operations

Press the TRK/TUNE DN or TRK/TUNE UP button

(6) to select channels CH1 – CH7.

Select Tracks for CD or CD Changer Operation

Press the TRK/TUNE DN or TRK/TUNE UP button

(6) to move to the previous track or next track.

Press and hold the TRK/TUNE DN or TRK/TUNE

UP button (6) for more than 3 seconds to activate

fast rewind or fast forward of the disc. Disc play

starts from when you release the button.

7. Mode Button: Press the MODE button (7) to step

sequentially through the following sources:

Radio Tuner > CD > CD Changer (optional)

> Auxiliary > Radio Tuner.

8. Display Area: This area displays Radio/CD func-

tions, along with all other activated functions (8).

MUTE

VOLUME

MUTE

123

POWER BAND SHIFT/SCAN

MODE

STEREO COMMANDER

VOLUME

MUTE

TRK

TUNE

TRK

TUNE

M5100CDUMFinal 2/1/05 4:58 PM Page 7

Installing the Unit

1. Using the foam adhesive backer of the remote as

a template, determine the mounting location on

the mounting surface and mark the three hole

locations.

2. Remove the foam adhesive backer and drill two

3/8" and one 5/8" mounting holes in the marked

positions.

3.Remove the backer to the foam adhesive backer

and adhere it to the back of the remote.

4. Feed the remote wire through the 5/8" hole in the

mounting surface and attach the remote to the

mounting surface using the supplied screws.

5. Attach the remote wire to the unit according to

the wiring diagram on Page 11.

Note: The Wired Remote comes with an extension

cord so the remote can be mounted a far distance

from the receiver.

This unit is a wired remote control made using a modified controller or similar layout. It is capable of

operating the specified functions on the M5100CD receiver. The body, buttons, controls and display are

UV and water-resistant. It includes a LCD and an illumination circuit.

Take a moment to read through this section and become familiar with the operations and features of this

outstanding product. It is advisable to keep this manual in your vehicle so it is readily available for refer-

ence. Be sure to fill out and send in your warranty card to ensure that you receive the full benefits of war-

ranty repair in the unlikely event that your system will need service.

Waterproof Wired Remote Introduction

Installation Procedures

Mounting Surface

Foam Adhesive

Backer

Mounting Surface

Mark & Drill Holes

Screws

Wire to Unit

Mounting Surface

M5100CDUMFinal 2/1/05 4:58 PM Page 8

tep 1: The radio chassis is designed to be “Panel

Mounted” through a opening in the mounting panel.

See the installation part of this manual for panel

mounting.

Step 2:

Bring all wiring for the connection of the

unit (including the antenna) through the mounting

hole. Connect the wiring as follows:

Yellow Wire: Connect this wire to a constant +12

volt power source (a power source that is not con-

trolled by the ignition key).

Red Wire(w/Fuse): Connect this wire to a switched +12

volt power source (a power source turned on and off

by the ignition key). The fuse has a rating of .5A.

Blue Wire: Connect this wire to the (+) power

antenna activation circuit. If no power antenna

exists, tape-off the end of this wire to prevent short-

ing out of the unit.

Black Wire: Connect this wire to the frame of the

vehicle (ground). This wire is the chassis grounding

wire for the unit.

White Wire: Connect this wire to the Left Main

Speaker (+) positive terminal or wire.

White Wire with Black Stripe: Connect this wire to the

Left

Main

Speaker (-) negative terminal or wire.

Green Wire: Connect this wire to the Left Remote

Speaker (+) positive terminal or wire.

Gre

en Wire with Black Stripe: Connect this wire to the

Left

Remote

Speaker (-) negative terminal or wire.

Gray Wire: Connect this wire to the Right Main

Speaker (+) positive terminal or wire.

Gra

y Wire with Black Stripe: Connect this wire to the

Right

Main

Speaker (-) negative terminal or wire.

Purple Wire: Connect this wire to the Right Remote

Speaker (+) positive terminal or wire.

Purple

Wire with Black Stripe: Connect this wire to the

Right

Remote

Speaker (-) negative terminal or wire.

Red/White RCA Connectors: Two sets of line out

cables are provided for connections to external

amplifiers.

Note: This unit is designed to connect to (4) four

speakers. If the installation only requires (2) two

speakers, use the White and Gray wire sets to con-

nect the speakers.

Wiring

WARNING!

Any wires left unconnected must be taped-off

or capped off to prevent shorting.

DO NOT connect speaker ground wires together.

DO NOT connect speaker ground wires to the

chassis of the vehicle.

DO NOT connect front and rear speaker wires

together.

FAILURE TO FOLLOW ANY OF THESE WARN-

INGS WILL RESULT IN DAMAGE TO THIS

UNIT AND VOIDS THE WARRANTY.

M5100CDUMFinal 2/1/05 4:58 PM Page 9

Wiring Diagram

M5100CD

White Wire

White Wire with Black Stripe

Left

Front

Speaker

Green Wire

Green Wire with Black Stripe

Left

Rear

Speaker

Gray Wire

Gray Wire with Black Stripe

Purple Wire

Purple Wire with Black Stripe

Right

Front

Speaker

Right

Rear

Speaker

Power Antenna

(Switched

+12v out)

Blue Wire

Ground (B-)

Black Wire

Yellow Wire

Red Wire

Battery

(+12v in)

Ignition

Switch (+12v in )

Antenna Socket

Red

Right Channel

White

Left Channel

RCA Connectors

Set 2

Connect to Line Input

of Optional Amplifier

Connect to Line Input

of Optional Amplifier

Red

Right Channel

White

Left Channel

RCA Connectors

Set 1

M5100CDUMFinal 2/1/05 4:58 PM Page 10

Auxiliary Connection

M5100CD

VCR

White RCA (Left)

Video Game

Audio Out From

VCR / TV /

Video Game

Auxiliary Audio Input

RCA with Yellow Cables

Red RCA (Right)

CD Changer Connection

M5100CD

CD Changer

(Optional)

8-Pin Din Connector

Male to Male 8-Pin Din Cable

(Supplied with CD changer)

Wired Remote Connection

M5100CD

Wired Remote

(Optional)

Female 8-Pin

Mini Din Connector

Male 8-Pin

Mini Din Connector

M5100CDUMFinal 2/1/05 4:58 PM Page 11

Remove Transportation Screws

Before installing the unit, remove the two

screws shown in the illustration below.

Note: If this unit is to be installed in a boat or a

spa, you should use the two pieces of plastic

film (30 mm X 20 mm) supplied to seal the two

holes after removing the screws.

Installing the Unit

1. Using the mounting paper template supplied

with the unit, determine the mounting location

and then stick the template on the location.

2. Cut and remove the hatching area on the tem-

plate. Then drill four 1/8" mounting holes in the

exact position according to the mounting paper.

3. Use the glue paper to stick the two mounting

brackets to the back of the mounting surface.

The screw holes of the brackets must respec-

tively aim at the mounting holes in order to fix

the unit to the mounting surface.

4. Open the two pieces of rubber cover on the unit to

display the four screw holes then using four screws

(M4X30) to mount the unit to the dashboard.

Installation

Mounting Surface

Template

Mounting

Holes

Mounting

Location

Mounting Surface

Mounting

Brackets

Mounting

Surface

Rubber Cover

Screws

Mounting Surface

Rubber

Cover

Remove screws

before installation

M5100CDUMFinal 2/1/05 4:58 PM Page 12

SYMPTOM CAUSE SOLUTION

No power The ACC Power Supply is not Both the red and yellow

connected. wires require power from the

power source.

The fuse is blown. Replace the fuse.

Disc cannot be loaded, Presence of disc inside the player. Remove the disc in the player, and

played or ejected replace it with another disc.

Disc was inserted upside down. Insert the compact disc with the

label facing up.

Compact disc is extremely dirty or Clean the disc or try playing a

disc is defective. another disc.

Temperature inside the unit is Allow the unit to cool off,

too high. then try again.

Condensation. Leave the player off for an hour, then

try playing it again.

No sound Volume is set at the minimum level. Adjust volume to the desired level.

Speaker wiring is not properly connected. Check the wiring connection.

Sound skips The installation angle is more Adjust the installation angle to less

than 30 degrees. than 30 degrees.

Compact disc is extremely dirty or Clean the disc or try playing a

disc is defective. another disc.

The operation keys The built-in microcomputer Press the RESET button.

do not work is not operating properly Front panel is not properly fixed

due to noise. into its place.

The radio does not work The antenna cable is not connected. Insert the antenna cable firmly.

The radio station automatic

The signals are too weak. Select a station manually.

does not work

Trouble Shooting

Before going through the trouble shooting table below, check the wiring connection. If the problem persist,

consult your nearest service dealer.

Installation

Mounting Surface

Washer

Nut

Sheet Metal

Screw

Metal Strap

M5100CDUMFinal 2/1/05 4:58 PM Page 13

Warranty

ONE (1) YEAR LIMITED WARRANTY

Magnadyne Corporation or its authorized agents will within one year from the date of sale to you,

repair, replace or refund the retail sales price of said product or any part thereof, at the option of

the Magnadyne Corporation or its authorized agents, if said product or part is found defective in

materials or workmanship, when properly connected and operating on the correct power require-

ments designated for the specific product. This warranty and Magnadyne Corporation or its autho-

rized agents obligations hereunder do not apply where the product was; damaged while in the pos-

session of the consumer, subjected to unreasonable or unintended use, not reasonably main-

tained, utilized in commercial or industrial operations, or serviced by anyone other than

Magnadyne Corporation or its authorized agents, or where the warning seal on the product is bro-

ken or the power and/or plugs are detached from the unit. Magnadyne Corporation or any of its

authorized agents will not assume any labor costs for the removal and reinstallation of any prod-

uct found to be defective, or the cost of transportation to Magnadyne Corporation or its authorized

agents. Such cost are the sole responsibility of the purchaser.

This warranty does not cover the cabinet appearance items or accessories used in connection with

this product, or any damage to recording or recording tape, or any damage to the products result-

ing from improper installation, alteration, accident, misuse, abuse or acts of nature.

MAGNADYNE CORPORATION OR ITS AUTHORIZED AGENTS SHALL NOT BE LIABLE TO

ANYONE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES OR CLAIMS EXCEPT THOSE

ACCORDED BY LAW. NO EXPRESSED WARRANTY OR IMPLIED WARRANTY IS GIVEN

EXCEPT THOSE SET FORTH HEREIN. NO IMPLIED WARRANTY SHALL EXTEND BEYOND

ONE YEAR FROM THE DATE OF SALE.

This warranty extends only to the original purchaser of the product and is not

transferable. Some states do not allow limitations on how long an implied warranty lasts, and

some states do not allow the exclusion or limitation of incidental or consequential damages,

so the above limitations or exclusion may not apply to you. This warranty gives you specific

legal rights, and you may have other rights that vary from state to state.

Defective merchandise should be returned to the original point of purchase or secondly, to:

Magnadyne Corporation, 1111 W. Victoria Street, Compton CA 90220

www.magnadyne.com

Return Authorization must be obtained before sending, or merchandise may be refused.

Specifications

GENERAL

Power Supply

Requirements:

DC 12 Volts, Negative

Ground

Chassis Dimensions:

178 mm (W) x 165 (D) x

50 (H)

Tone Controls:

Bass: 100 Hz ±10 dB

Treble: 10 kHz ±10 dB

Maximum Output Power:

4 x 50 watts

Current Drain:

15 Ampere (Max.)

CD PLAYER

Signal to Noise Ratio:

> 55 dB

Channel Separation:

> 50 dB

Frequency Response:

40Hz – 18 kHz

FM RADIO

Frequency Coverage:

87.5 to 107.9 MHz

Sensitivity (S/N=30dB):

3µV

Stereo Separation:

> 30dB

AM RADIO

Frequency Coverage:

530 to 1720 kHz

Sensitivity (S/N=20dB):

32 dBu

M5100CDUMFinal 2/1/05 4:58 PM Page 14

A Registered Trademark of Magnadyne Corporation

M5100CDUMFinal 2/1/05 4:58 PM Page 16

Magnadyne Stereo Receiver M5100CD User manual

Brand: Magnadyne

Model: Stereo Receiver M5100CD

Category: Car media receivers

Type: User manual

This manual is also suitable for

Download PDF

report

Magnadyne Stereo Receiver M5100CD User manual

This manual is also suitable for

Magnadyne Stereo Receiver M5100CD User manual

Related papers

Other documents