Professional Table
Tools Required: Phillips screwdriver, ruler, and drill with 1/16" bit (tools not included)
Assembly Instructions
Figure 3
MODEL X-3-XB, MODEL X-4-XB,
MODEL XI-3-XB, MODEL XI-4-XB,
MODEL XII-3-XB, MODEL XII-4-XB
Parts Included:
A 1pc Leg Frame
Unfold leg frame (A). Insert rear extension tubes (C) into
back tubes of leg frame with mounting brackets facing out.
Slide tubes in as far as they will go and then loosely hand-
tighten height adjustment knobs (F). See
Figure 1
.
Insert front extension tubes (D) into front tubes of leg
frame with the curved black caps facing front and back. See
Figures 1 & 2
. Set each tube at a height of approximately 4"
and then loosely hand-tighten height adjustment knobs.
Place tabletop (B) with preferred side down on a
carpeted or protected floor to prevent scratching. Turn the
assembled base frame upside down and place on tabletop
with front guide tracks (G) placed (but not screwed in yet)
under the front extension tubes. See
Figure 3.
1
2
B 1pc Tabletop C 2pcs Rear Extension Tubes
E 2pcs Floor Glides
(Already installed
into legs)
F 4pcs Height
Adjustment Knobs
H 12pcs 1/2"
Wood Screws
To Assemble:
Unpack parts and inspect to confirm that all are present.
G 2pcs Front Guide Tracks
3
D 2pcs Front Extension Tubes
(Shipped in
separate box)
Figure 2
B
C
C
C
F
G G
D
D
D
Page 1 of 2
Assembled table Figure 1
Professional Table
Assembly Instructions
TIP
5
6
7
©2015 ALVIN & COMPANY, INC. • P.O. Box 188, Windsor, CT 06095-0722
Phone: 860-243-8991 • Toll-Free: 800-444-2584 • Fax: 860-242-8037 • Toll-Free Fax: 800-777-2896
www.alvinco.com
LIT-A15138 11/15
Drop all extension tubes down to their lowest positions. Lift
the tabletop up until the front extension tubes disengage from
the front guide tracks, then move the left leg frame in until it
is flush against the rear frame assembly. Next, move the right
leg frame in flush against the left leg frame. Gently lower the
tabletop down flush against the folded legs. The table is now
ready for storage.
To Fold Table:
For 24" x 36" Tabletop
Center base frame until
A dimensions are equal
Front
Back
1"
3¾"
1½"
1½"
1"
3¾"
A A
For 36" x 48" Tabletop
Front
Back
10½" 10½"
2"
9¾"
2"
9¾"
A A
Center base frame until
A dimensions are equal
For 31" x 42" Tabletop
Front
Back
5½" 5½"
2"
6¾"
2"
A A
Center base frame until
A dimensions are equal
6¾"
Page 2 of 2
Position the frame and front guide tracks using the
dimensions to the left, according to the size of your
tabletop. Be sure to center the frame from left to right.
Mark front guide track and rear extension tube bracket hole
locations with a pencil or awl.
Using a 1/16" bit, drill pilot holes 1/4" deep only. Use care
not to drill through the table top.
Wrap masking tape 1/4" from drill bit end to determine drilling depth.
Attach rear extension tube brackets and front guide tracks
to tabletop using 1/2" wood screws (H). See
Figures 4 & 5
.
Tighten securely but use care not to strip.
Carefully return table to upright position. Adjust tabletop to
desired height and angle using height adjustment knobs.
You’re finished and your table is ready to use.
Figure 4 Figure 5
4
H
H
x4
x2
-
1
-
2
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Alvin Professional Spacesaver X1-4-XB User manual
-
-
-
-
-
-
-
-
-
