Tyan THUNDER I7525 User manual

Brand: Tyan

Model: THUNDER I7525

Type: User manual

This manual is also suitable for

Thunder i7525 S2676

Thunder i7525 (S2676) User’

s Manual

http://www.tyan.com

Thunder i7525

///

S2676

Revision 1.00

be reproduced or translated without prior written consent from TYAN Computer Corp.

All registered and unregistered trademarks and company names contained in this manual are

property of their respective owners including, but not limited to the following.

TYAN, Thunder i7525 and (S2676) are trademarks of TYAN Computer Corporation.

Intel, Xeon, and combinations thereof are trademarks of Intel Corporation.

Phoenix, PhoenixBIOS are trademarks of Phoenix Technologies.

Microsoft and Windows are trademarks of Microsoft Corporation.

Linux is a trademark of Linus Torvalds.

IBM, PC, AT and PS/2 are trademarks of IBM Corporation.

ATI, ATI RAGE is a trademark of ATI Technologies Incorporated.

SMSC is a trademark of SMSC - Standard Microsystems Corporation.

Portable Document Format (PDF) is a trademark of Adobe Corporation.

Information contained in this document is furnished by TYAN Computer Corporation and has been

reviewed for accuracy and reliability prior to printing. TYAN assumes no liability whatsoever, and

disclaims any express or implied warranty, relating to sale and/or use of TYAN products including

liability or warranties relating to fitness for a particular purpose or merchantability. TYAN retains

the right to make changes to product descriptions and/or specifications at any time, without notice.

In no event will TYAN be held liable for any direct or indirect, incidental or consequential damage,

loss of use, loss of data or other malady resulting from errors or inaccuracies of information

contained in this document.

Thunder i7525 (S2676) Table of Contents

http://www.tyan.com

Table of Contents

Before you begin…...........................................................................................................................................................Error! Bookmark not defined.

Chapter 1: Introduction................................................................................................................................................................................................1

1.1 – Congratulations!..............................................................................................................................................................................................1

1.2 – Hardware Specifications .................................................................................................................................................................................1

1.3 – Board Diagram................................................................................................................................................................................................3

Chapter 2: Choose Proper Parts For Your System....................................................................................................................................................4

2.1 – Central Processor Unit (CPU) Considerations................................................................................................................................................4

2.2 – Memory Considerations..................................................................................................................................................................................4

2.3 – Chassis/Enclosure Considerations..................................................................................................................................................................5

2.4 – Power Supply Considerations.........................................................................................................................................................................5

Chapter 3: Board Installation.......................................................................................................................................................................................7

3.1 –Key Component View.......................................................................................................................................................................................8

3.2 – Jumper Settings & Definitions.......................................................................................................................................................................11

3.3 – Mounting the Motherboard............................................................................................................................................................................17

3.4 – Installing the Processor and Heatsink...........................................................................................................................................................17

3.4 – Installing the Memory....................................................................................................................................................................................20

3.5 – Memory Installation Procedure......................................................................................................................................................................20

3.6 – Attaching Drive Cables..................................................................................................................................................................................21

3.7 – Installing Add-In Cards..................................................................................................................................................................................23

3.8 – Connecting External Devices........................................................................................................................................................................25

3.9 – Installing the Power Supply...........................................................................................................................................................................25

3.10 – Finishing Up ................................................................................................................................................................................................26

Chapter 4: BIOS Setup................................................................................................................................................................................................27

4.1 – Main BIOS Setup..........................................................................................................................................................................................28

4.2 – Main Submenu Standard / Native IDE ............................................................................................................................................................1

4.3 – Advanced BIOS Features...............................................................................................................................................................................3

4.4 – Security Menu...............................................................................................................................................................................................16

4.5 – Power Menu..................................................................................................................................................................................................18

4.6 – Boot Menu.....................................................................................................................................................................................................19

4.7 – Exit Menu......................................................................................................................................................................................................21

Chapter 5: Diagnostics...............................................................................................................................................................................................22

5.1 Beep Codes.....................................................................................................................................................................................................22

5.2 Flash Utility ......................................................................................................................................................................................................22

Appendix I: Glossary....................................................................................................................................................................................................1

Appendix II: Post Error Code for BIOS........................................................................................................................................................................7

Appendix III: SMDC Information................................................................................................................................................................................12

Technical Support..................................................................................................................................................................................................13

Thunder i7525 (S2676) Before you begin…

iii

http://www.tyan.com

Before you begin…

Check the box contents!

The retail motherboard package should contain the following:

1x Thunder i7525 (S2676) motherboard

1x 34-pin floppy drive cable

1x 80-pin Ultra-DMA-133/100/66/33 IDE cable

1x 68-pin Ultra 320 SCSI cable (Optional)

1x Thunder i7525 (S2676) User’s Manual

1x Thunder i7525 (S2676) Quick Reference

1x TYAN driver CD

1x I/O shield

1 x Serial ATA driver diskette

SCSI Driver Disk (Optional)

1 x Serial ATA power cable

2 x Serial ATA cables

If any of these items are missing, please contact your vendor/dealer for replacement before

continuing with the installation process.

Thunder i7525 (S2676)

http://www.tyan.com

Chapter 1: Introduction

1.1 – Congratulations!

You have purchased one of the most powerful Intel Xeon



-based workstation solutions in a

standard SSI EEB v3.5 form factor.

Based on the Intel E7210 chipset, the Thunder i7525 (S2676) features some state-of-the-art

technologies such as dual/single 800 MHz FSB Xeon



processor support, multiple PCI-Express

buses, dual channel DDR2 memory design, onboard PCI-Express Gigabit Ethernet port, Serial-

ATA IDE ports, and multiple USB2.0 (Universal Serial Bus) ports. By doubling the capability of

existing AGP8x designs with transfer rates of 4.0 Gigabytes per second over a x16 PCI Express

lane for graphics controllers, the onboard x16 PCI-Express slot supports a high performance

graphics infrastructure for high-end gaming or multimedia.

Visit Tyan’s website at http://www.tyan.com. There, you can find information on all of Tyan’s

products with up-to-date FAQs, a list of worldwide distributors, Tyan software utilities, the latest

drivers, memory compatibility listings, and BIOS setting explanations.

1.2 – Hardware Specifications

Processors

- Dual mPGA604 ZIF sockets

- Supports single or dual Intel Xeon



processors (Nocona)

- 800MHz Front-Side Bus

- Dual onboard 4-phase VRD10.1 complaint

voltage regulation design

Chipset

- Intel E7525 chipset

§ E7525 MCH (North Bridge)

§ ICH5R (South Bridge)

§ PXH (PCI-X hub)

- SMSC LPC47B397 Super I/O chip

Expansion Slots

- One x16 PCI-Express high-performance

Graphics slot

- One PCI-X 64-bit 133/100/66MHz (3.3-

Volt) slot

- Two PCI-X 64-bit 100/66MHz (3.3-volt)

slots

- One PCI 32-bit 33MHz (5-Volt) slots

- Total of six usable slots

Memory

- Eight 240-pin 1.8-Volt DDR2 400 DIMM

sockets

- Dual channel memory bus

- Supports ECC or non-ECC memory

- Up to 16GB of Registered DDR2 DIMM

modules

Integrated LAN

- Broadcom BCM5751 PCI Express Gigabit

Ethernet Controller

System Hardware Health Monitor

- Total four 3-pin fan headers with

tachometer monitoring and five of them

with PWM control

- Chassis intrusion header

- Temperature and voltage monitoring

- Watchdog timer

BIOS

- Phoenix BIOS 4Mbit flash ROM

- Supports ACPI 1.0b, PnP, DMI 2.0

- Auto configuration of IDE devices

- Multiple boot options

- Power Management: ACPI S1, S3, S4 and

S5 modes

Other Integrated I/O Interfaces

- One floppy connector for up to two drives

- One UART serial port connector

- One ECP/EPP/SPP parallel connector

- Four USB2.0 ports (2 front USB ports via

an optional cable)

- PS/2 mouse & keyboard ports

Form Factor

- SSI EEB 3.5 footprint (12”x13”,

Thunder i7525 (S2676)

http://www.tyan.com

Integrated Audio

- Intel ICH5R AC’97 compliant audio link

- Analog Device AD1981B CODEC

- Line-in, Line-out, Mic-in rear vertical jacks

and a front panel audio header

- One 4-pin CD-ROM audio input header

- One 4-pin Auxiliary header

Integrated Mass Storage Port

- Two ICH5-S integrated SATA ports up to

1.5 Gbit/s with SATA RAID 0,1 under

Windows

- Two bus-master UDMA ATA100/66/33

Parallel IDE channels support up to 4

ATA/ATAPI complaint devices

305x330mm)

- EPS12V V3.51 power connectors

- Rear I/O

§ Stacked PS/2 mouse and keyboard

connectors

§ One parallel connector

§ One GbE RJ45 connector

§ Four stacked USB connectors

§ Stacked audio connector for MIC,

Line_out and Line_in.

Regulatory

- FCC Class B (Declaration of Conformity)

- European Community CE (Declaration of

Conformity)

Note: TYAN reserves the right to add support or discontinue support for any OS with or without

notice.

Software Specifications

OS (Operating System) Support

Microsoft Windows XP

Microsoft Windows 2000 advanced Server

Microsoft Windows Server 2003

Microsoft Windows NT4.0

Red Hat 8.0, 9.0

SuSE Server 8.0

Other distributions of Linux pending validation

TYAN reserves the right to add support or discontinue support for any OS with or without

notice.

Thunder i7525 (S2676)

http://www.tyan.com

1.3 – Board Diagram

The above picture is purely representative. Due to engineering updates and new board

revisions, certain components may change and or be repositioned. The picture above may

or may not look exactly like the board you received.

The following page includes details on the vital components of this motherboard.

Thunder i7525 (S2676)

http://www.tyan.com

Chapter 2: Choose Proper Parts For Your System

Before you installing a system with this motherboard, make sure your major system parts meet

the following basic guidelines and requirements:

2.1 – Central Processor Unit (CPU) Considerations

§ Process Type and Package

Thunder i7525 (S2676) board supports Intel Xeon



processors in 604-pin Pin Grid

Array package.

§ Front Side Bus (FSB)

The processor host bus, or called Front Side Bus (FSB), always operates at 800 MHz.

Choose Intel Xeon



800 MHz FSB processors for Thunder i7525 (S2676) board.

The system will not be operational when installing Intel Xeon



533 or 400 MHz FSB

processors.

§ Single/Dual Processor System

Thunder i7525 (S2676) board supports single or dual Intel Xeon



processors.

Single Processor System:

When only install a single processor on Thunder i7525 (S2676) board, the processor

must be installed on the CPU1 ZIF (Zero-Insertion-Force) socket.

Dual Processor System:

Thunder i7525 (S2676) board supports dual processor configurations only in which both

processors operate with the same FSB frequency, core frequency, and have the same

internal cache sizes. Mixing processors operating at different FSB frequency, core

frequency, or cache sizes may cause system non-operation or damages on processors

and/or the motherboard.

2.2 – Memory Considerations

§ Memory Type

Thunder i7525 (S2676) board supports up to four 240-pin 1.8-Volt DDR2 400

Registered ECC DIMM modules. The DDR2-400 memory modules can be using

256Mb, 512Mb and 1Mb memory chips.

DDR-I or Unbuffered DDR memory modules are not supported by Thunder i7525

(S2676) design.

Visit Tyan’s web site for the memory recommendation list.

§ Memory Installation

Thunder i7525 (S2676) is based on Intel’s E7525 Tumwater chipset, which supports

144-bit wide dual memory channels in memory interleaved scheme. System requires

minimum two memory modules, as a pair, to boot up the system.

You must install two memory modules at a time, as a pair, stating from DDR2-DIMM1

and DDR2-DIMM2 (marked as MMX1 and MMX2, respectively). Each memory module

in a pair must be in the same capacity, speed, and configuration.

Thunder i7525 (S2676)

http://www.tyan.com

2.3 – Chassis/Enclosure Considerations

§ Motherboard size

Thunder i7525 (S2676) board is in the board size of 12” (W) x13” (L).

§ Motherboard and CPU Heat-sink Mounting Holes

There are six motherboard-mounting holes and eight CPU heat-sink mounting holes on

Thunder i7525 (S2676) board design. The motherboard and CPU mounting hole

locations follow SSI EEB v3.51 (A Server System Infrastructure specification for Entry

Pedestal Servers and Workstations) specifications. Ensure that your chassis supports

those 6 motherboard-mounting holes to secure the motherboard.

Thunder i7525 (S2676) supports Intel’s CEK (Common Enabling Kit) for securing Intel’s

Xeon



800 MHz FSB processors in the chassis. Two CEK springs for the dual

processors are pre-assembled with the motherboard or enclosed in the motherboard

accessory package. The CPU heat-sinks must be mounted down to the chassis base

pan with stand-offs. Any additional chassis standoffs, besides the 6 motherboard-

mounting holes and 8 CPU heat-sink mounting holes, should be removed to preventing

from short-circuit or motherboard damage.

§ Others

As a system integrator, the air-flow/thermal, EMI/EMC, shock/vibration, and system

packing should be also considered for choosing a proper enclosure.

2.4 – Power Supply Considerations

§ Power connectors

Thunder i7525 (S2676) board supports EPS/12V power supply unit (PSU) with three

power connectors listed below.

EPS/12V Power Connectors

24-pin system power connector 8-pin CPU power connector

(split CPU power planes)

§ Split processor power planes

Thunder i7525 (S2676) board supports dual Intel’s 800 MHz FSB Xeon



processors,

which could reach up to 140 Watts per processor. (Check Intel’s web for the processor

specifications.) By following SSI EEB v3.51 specifications, Thunder i7525 (S2676) is

designed with two separate voltage regulator circuits to provide the power for both

onboard processors in separate power rail. Using a power supply with a combined

CPU power plane from the CPU power connector is not allowed and may cause the

system to fail to power up or damage to the power supply.

§ Power requirements

Check your power supply specifications to ensure sufficient power currents for each

power rail based on your system configuration.

The major system components/parts power sources are listed below as reference:

Thunder i7525 (S2676)

http://www.tyan.com

Components/Parts Main Power Source Power Connectors

CPU1 +12V_CPU1 8-pin CPU power connector

CPU2 +12V_CPU2 8-pin CPU power connector

Memory (Normal) +12V 24-pin and 6-pin power connectors

Memory

(Suspend to RAM)

+5Vstandby 24-pin power connector

System logic +3.3V 24-pin and 6-pin power connectors

x16 PCI-Express

Graphic card

+12V and +3.3V 24-pin and 6-pin power connectors

x8 PCI-Express +12V and +3.3V 24-pin and 6-pin power connectors

32-bit PCI +12V, +5V and +3.3V 24-pin and 6-pin power connectors

Cooling fans +12V 24-pin and 6-pin power connectors

IDE/SATA hard drives +12V and +5V From PSU

CDROM/DVD drives +12V and +5V From PSU

Thunder i7525 (S2676)

http://www.tyan.com

Chapter 3: Board Installation

How to install our products right…. the first time!

The first thing you should do read this user’s manual. It contains important information that will

make configuration and setup much easier. Here are some precautions you should take when

installing your motherboard:

(1) Ground yourself properly before removing your motherboard from the antistatic bag.

Unplug the power from your computer power supply and then touch a safely grounded

object to release static charge (i.e. power supply case). For the safest conditions,

TYAN recommends wearing a static safety wrist strap.

(2) Inspect the mounting holes pattern of the Thunder i7525 (S2676) to match your chassis

standoff locations and remove the additional standoffs.

(3) Hold the motherboard by its edges and do not touch the bottom of the board, or flex the

board in any way.

(4) Avoid touching the motherboard components, IC chips, connectors, memory modules

and leads.

(5) Place the motherboard on a grounded antistatic surface or on the antistatic bag that the

board was shipped in.

(6) Inspect the board for damage.

(7) Check the jumper settings and connector locations as described in next sections.

In last sections of this chapter, we will cover the details on how to install your motherboard into

your chassis, as well as installing the processor, memory, disk drives and cables.

Note: DO NOT APPLY POWER TO THE BOARD IF IT HAS

BEEN DAMAGED

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

Thunder i7525 (S2676)

http://www.tyan.com

3.1 –Key Component View

Thunder i7525 (S2676)

http://www.tyan.com

Fig. 3-1 Thunder i7525 (S2676) Key Component View

Thunder i7525 (S2676)

http://www.tyan.com

This jumper diagram is representative of the latest board revision available at the time of

publishing. The board you receive may or may not look exactly like the above diagram.

The board parts are not to scale.

Thunder i7525 (S2676)

http://www.tyan.com

3.2 – Jumper Settings & Definitions

Jumper /

Connector

Function

P1 24-pin system power connector

P3 8-pin CPU power connector

P7 CD-ROM audio input connector

P10 Keyboard/Mouse

P11 Auxiliary audio input connector

P20 Primary IDE Connector

P21 Secondary IDE Connector

P23 Audio

P29 SCSI LED

P11 Auxiliary audio input connector

P20 Primary IDE connector

P21 Secondary IDE connector

P23 Reserved

P24 Front USB Header

J3 TPM Disable

J9 External LAN connector

J10 Rear USB connector

J11 Rear IEEE1394 connector

J12 Front IEEE1394 connector

J32 Floppy Drive connector

J86 Front Panel connector

J102 PS/2 Wake up 1-2: No PS/2 wake up

3-4: PS/2 wake up

J104 BIOS write protect Install: BIOS write protected

J106 LCD connector

J107 Remote Thermal Sensor

J108 Clear CMOS

J109 PSU PC98 Connector

J110 FAN 1Connector

J111 FAN 2 Connector

J112 FAN 4 Connector

J113 FAN 3 Connector

J114 SPDIF

J137 LAN Disable

Note: All fans may be monitored from BIOS.

Jumper Example

OPEN - Jumper OFF Without jumper cover

CLOSED - Jumper ON With jumper cover

To indicate the location of pin-1

Thunder i7525 (S2676)

http://www.tyan.com

3.2.1 - Clear CMOS Switch

J108

You can reset the CMOS settings by Closing

header J108, if you have forgotten your

system/setup password or need to clear

system BIOS settings.

- Power off system and disconnect

both power connectors from

the motherboard

Close J108 for several seconds to

Clear CMOS

- Remove Jumper

Reconnect power & power on system

3.2.2 - Fan Connector

Pin1: GND

Pin2: +12V

Pin3: Tachometer

This 3-pin fan connector supports tachometer monitoring.

There are three 3-pin fan connectors on Thunder i7525 (S2676) board. Use these connectors

to connect chassis and processor cooling fans to your motherboard. Cooling fans can keep

the system stable and reliable for its product’s life.

3.2.3 - Front Panel Header

Normally, a chassis has some control or signal wires can be connected onto a motherboard for

hard drive LED, Power LED, power button, and reset button,

The front panel header (marked as “j86”) has been implemented on Thunder i7525 (S2676) board

for such purposes.

Thunder i7525 (S2676)

http://www.tyan.com

Front Panel Header

(J86)

Function PIN # PIN # Function

HDD LED+ 1 2 LED_GRN

HDD LED# 3 4 LED_YEL

GND1 5 6 FP_PBTN#

FP_RESET 7 8 GND2

+5V 9 10 FP_SLP#

IRRX 11 12 GND3

GND4 13 14 Key

IRTX 15 16 IR_PWR

RSVD1 17 18 RSVD2

J86

Thunder i7525 (S2676)

http://www.tyan.com

3.2.4 - Front USB Connector (USB2)

Front USB Header (P24)

Functio

Power 1 2 Power

USB6- 3 4 USB7-

USB6+ 5 6 USB7+

GND 7 8 GND

Key 9 10 Reserve

3.2.5 – External HDD LED Input Header (P29)

P29

P24

Thunder i7525 (S2676)

http://www.tyan.com

Pin# Function

1 NC

2 LED2-

3 LED2-

4 NC

P29

Thunder i7525 (S2676)

http://www.tyan.com

3.2.6 - Serial ATA Connectors (SATA0 & SATA1)

SATA0/SATA1 (from Intel’s FW82801ER/ICH5R South Bridge chip):

User can connect up to two serial ATA hard disks to run IDE mode or configure both drives to a

RAID under Windows. The RAID level 0 or level 1 function is supported for Microsoft’s Windows

XP and Windows 2000 operating systems.

Serial ATA connectors

For informatio n regarding the setup of SATA/RAID, you may search the contents of the

driver CD that shipped with your motherboard or visit our website at:

HTTP://WWW.TYAN.COM/

SATA1

SATA2

Thunder i7525 (S2676)

http://www.tyan.com

3.3 – Mounting the Motherboard

Before installing your motherboard, make sure your chassis has the necessary motherboard

support studs installed. These studs are usually metal and are in gold or silver color. Usually, the

chassis manufacturer will pre-install the support studs. Remove the unused or additional studs,

which may scratch the motherboard or cause short-circuit with the components on the bottom

side. If you’re unsure of stud placement, simply lay the motherboard inside the chassis and align

the screw holes of the motherboard to the studs inside the case. If there are any studs missing,

you will know right away since the motherboard will not be able to be securely installed. Some

chassis’ include plastic studs instead of metal. Although the plastic studs are usable, TYAN

recommends using metal studs with screws that will fasten the motherboard more securely in

place.

3.4 – Installing the Processor and Heatsink

Your Thunder i7525 (S2676) supports the latest processor technologies from Intel. Check the

following page on TYAN’s website for latest processor support:

http://www.tyan.com

The following diagrams will detail how to install your processor:

The diagram is provided as a visual guide to help you install socket processors and may not be an

exact representation of the processors you have.

1. Lift the lever on the socket until it is approximately 90

or as far back as possible to the

socket.

2. Align the processor with the socket. There are keyed pins underneath the processor to

ensure that the processor’s installed correctly.

3. Seat the processor firmly into the socket by gently pressing down until the processor

sits flush with the socket.

4. Place the socket lever back down until it locks into place.

5. Your processor is installed.

Take care when installing the processor as it has very fragile connector pins below the

processor that can bend and break if inserted improperly.

Heatsink Installation

After you are done installing the processor, you should proceed to installing the heatsink.

Heatsink will ensure that the processor not overheat and continue to operate at maximum

Page is loading ...

Tyan THUNDER I7525 User manual

Brand: Tyan

Model: THUNDER I7525

Type: User manual

This manual is also suitable for

Thunder i7525 S2676

Download PDF

report

Tyan THUNDER I7525 User manual

This manual is also suitable for

Tyan THUNDER I7525 User manual

Related papers

Other documents