1
M A N U A L
N I - 7 0 7 5 0 2
2
C O N T E N T S O F T H E P A C K A G E 4
T E C H N I C A L S P E C I F I C AT I O N S
4
R A N G E O F A P P L I C AT I O N S
4
H A R D W A R E I N S TA L L AT I O N
5
R O U T E R C O N F I G U R AT I O N
6
3
T ha n k y o u f o r b u y i n g t h i s X R t e c h n o l o g y r o u t e r. T h e
e X t e n d e d R a n g e t e c h n o l o g y e x t e n d s y o u r w i r e l e s s
c o v e r a g e t o u p t o t h r e e t i m e s m o r e t h a n t h a t o f a
s t a n d a r d 5 4 M b p s p r o d u c t .
I f y o u w a n t t o i n t e r c o n n e c t s e v e r a l P C s f o r s h a r e d
I n t e r n e t a c c e s s , y o u w i l l n e e d a n a d d i t i o n a l c o m p o n e n t
t o c o n n e c t t h e P C s . T h i s r o u t e r a l l o w s y o u t o s e t u p a
w i r e l e s s n e t w o r k , q u i c k l y a n d e f f i c i e n t l y.
4
C O N T E N T S O F T H E P A C K A G E
Before starting the installation first check that all necessary parts are present. The
box should contain:
- 4 Port wir
eless router
- Power adapter 9V~ 800mA / 7.2VA
- CD with full manual
- User manual
T E C H N I C A L S P E C I F I C AT I O N S
- 802.11g wireless protocol
- Supports: IEEE 803.3, IEEE 803.3u, IEEE 802.11b, and IEEE 802.11g
- Supports: WEP/WPA/WPA2/802.1X data encryption
- Supports: 64/128/152 bit WEP encryption security
- Maximum wireless data transfer speed: 54 Mbps
- eXtended Range Technology
- Web Based Management
- Supports: Dynamic IP, Static IP, PPPoE
- 1 x WAN, 4 x LAN RJ-45 UTP ports
- Built-in NAT and DHCP server
- Supports: VPN pass through
- Independent of operating system
R A N G E O F A P P L I C AT I O N S
This router allows you to set up a wireless broadband Internet connection on
multiple computers. Op top of a shared Internet connection, you can also set up
a network between several PCs. Connect the ADSL modem to the WAN port of the
5
router and after a few seconds the WAN LED will light up. You can now connect the
PCs. Once the PCs have been started up, the relevant LED will light up.
H A R D W A R E I N S TA L L AT I O N
As soon as you have connected the router to the power adapter, the power LED
(Green) will light up and the link/act LEDs will flash once. The other LEDs (Green)
will light up as soon as one of the UTP ports are connected to the computer. When
data is transferred from one computer to another the LEDs will start to flash.
L E D I N D I C A T O R S
Name LED Action Description
PWR
OFF No Po
wer
ON Po
wer ON
SYS
ON Router is starting up
Flashing Router is r
eady to use
OFF Har
dware Error (reset the router)
WLAN
OFF Wir
eless connection is disabled
Flashing Wir
eless connection is enabled
WAN, 1-4
OFF Ther
e is no network connection between computer
and router
ON Ther
e is a network connection between computer and
router
Flashing Ther
e is data activity on the network
6
OV E RVIE W OF C O NNE C T ION S AT T H E BA C K OF T HE R O UTE R
R O U T E R C O N F I G U R AT I O N
After you have correctly connected the router, you can start to configure it. For
some providers you will need addition information, such as your username and a
password.
Start up the Internet browser and enter the following address in the address bar
http://192.168.1.1 and press “Enter”
The following screen is displayed. To access the router enter “admin” for username
and “password” for password and then click “OK”
7
After clicking “OK” the router setup screen is displayed.
8
Click on “Quick Setup” and then click on “Next”. Select your Internet connection,
and after your provider has given you a username and password, which is needed
for cable connections, select the PPPoE option.
If you already have an ADSL connection with an ADSL modem then select ‘Dynamic
IP”. The IP address is automatically allocated by your provider which the router will
then use.
If you have Dynamic IP click on “Next” to go directly to the
“Quick Setup – Wireless” screen
9
If you have a PPPoE connection, enter your username in the “Account name” field
and the password you were given by your provider in the “Password” field. Then
click on “Next”.
After clicking on “Next” the “Quick Setup - Wireless” screen is displayed.
If there is nothing you want to change, click on “Next”.
1 0
After you have clicked on “Finish” you will return to the “Router status” screen.
Now that the router has been set up it is important that the wireless function of the
router is protected. If you do not protect the router then the people around you will
be able to use your Internet connection.
In the main screen of the router, click the “Wireless”
“Wireless Settings” option
and the following screen is displayed. Enable the “Enable Wireless Security”
function.
1 1
Select WPA-PSK/WPA2-PSK for security type.
For the “PSK Passphrase” function enter your own network key and make a note of
the key as you will need it to make a wireless client connection
with the router.
After you have entered all the details, click on “Save”.
The following message appears: “Selecting the incorrect country may cause inter
-
ference with other devices and violate the applicable law” Click “OK”.
Click ‘OK’ again to restart the router.
Use this space to write down your router’s settings.
W I R E L E S S S E T T I N G S
SSID: ………………………......................…..
PSK Passphrase: ……………………………..
NB
To get the most out of your router, please see the complete manual on the CD-ROM.
1 2
I CI DU.CO M
W A R R A N T Y
Unless specified otherwise, all items sold under the ICIDU name are covered by
a two-year warranty. No warranty or support is provided for the software and
rechargeable batteries that are provided. Claims under warranty can be made only
via the dealer from whom the item was purchased.
Specifications can be changed without notice.
All ICIDU products comply with current European safety and environmental stand
-
ards and legislation. For further details, visit our website www.icidu.com
ICIDU is a registered trademark. All other brand names and rights in connection
with them are and remain the property of the rightful owner.
© Copyright 2007 ICIDU
All rights expressly reserved
/