Hitachi CG 10DL Technical Data And Service Manual

Brand: Hitachi

Model: CG 10DL

Type: Technical Data And Service Manual

This manual is also suitable for

Hitachi CG 10DL is a cordless, lightweight, and versatile gardening tool that combines the functionality of both a shrub shear and a grass shear. Its powerful 10.8 V lithium-ion battery provides ample power for various gardening tasks, while its compact design and ergonomic handle ensure comfortable use. The tool comes equipped with both a shrub shear blade and a grass shear blade, allowing you to effortlessly trim hedges, prune garden trees, and mow lawns.

[NEW FEATURES]

This product performs both shrub shearing and

grass shearing functions.

A 10.8 V lithium-ion battery (Model BCL1015) is

included.

A low charge warning lamp is included.

A large work area can be covered on a single charge.

A soft grip handle is attached.

The handle is thin along its circumference.

A large-size protector is attached.

An adjuster is included for adjusting shearing height.

LIST Nos.

CH 10DL: H832

CG 10DL: H833

Mar. 2009

This product includes a 10.8 V lithium-ion battery.

This new product offering the features below will be released to increase market share and sales of the

Gardening Tool Series.

(1) The main body of this product accepts both a shrub shear blade and a grass shear blade.

(2) A newly developed 10.8 V/1.5 Ah, lithium-ion battery is included.

(3) A low charge warning lamp is included.

(4) A large work area can be covered on a single charge.

(5) A soft grip handle is attached.

(6) The handle is thin along its circumference.

Shrub shear

x For trimming hedges and pruning garden trees

Grass shear

x For mowing lawns

International Sales Division

MARKETING OBJECTIVE

APPLICATIONS

SELLING POINTS

SPECIFICATIONS AND PARTS ARE SUBJECT TO CHANGE FOR IMPROVEMENT.

PRODUCT NAME

Hitachi 10.8 V Cordless Shrub Shear

Model CH 10DL, CH 10DL (CG)

Hitachi 10.8 V Cordless Grass Shear

Model CG 10DL

Shrub shear

Grass shear

REMARKS:

x For more information about HANDLING INSTRUCTIONS, visit our website at:

http://www.hitachi-koki.com/manual_view_export/

x This TECHNICAL DATA AND SERVICE MANUAL utilizes symbols to denote the company names and

model names of our competitors. The symbols utilized herein are as follows:

Competitors

Symbols Utilized

Company Name Model Name

BBOSCH Isio

C B&D SSC1000

CONTENTS

Page

SELLING POINTS ------------------------------------------------------------------------------------------------------------- 1

SPECIFICATIONS --------------------------------------------------------------------------------------------------------------4

COMPARISON WITH SIMILAR PRODUCTS---------------------------------------------------------------------------- 6

1. Comparison Specifications

------------------------------------------------------------------------------------------------------------ 6

PRECAUTIONS ON SALES PROMOTION ------------------------------------------------------------------------------ 7

1. Handling Instructions

--------------------------------------------------------------------------------------------------------------------- 7

2. Precautions on Efficient Use of the Charger and Battery

----------------------------------------------------------- 9

REPAIR GUIDE---------------------------------------------------------------------------------------------------------------- 10

1. Precautions on Disassembly and Reassembly

------------------------------------------------------------------------- 10

2. Precautions on Disassembly and Reassembly of the Battery Charger

----------------------------------- 13

STANDARD REPAIR TIME (UNIT) SCHEDULES-------------------------------------------------------------------- 14

Assembly Diagram for CH 10DL

Assembly Diagram for CG 10DL

-1-

Shrub shear blade Grass shear blade

Crank holder

Crank cam (for shrubs)

Blade case

Blade

Blade cover

Crank holder

Crank cam (for grass)

Blade

x UC 10SFLx BCL 1015

This product performs both shrub shearing and grass shearing

functions.

This excellent product can accommodate a shrub shear blade or a grass shear blade in its main body.

The shrub shear blade can be attached to the main body to trim hedges and prune garden trees.

The grass shear blade can be attached to the main body to mow lawns and is particularly effective in

edging lawns near stones or walls.

A 10.8 V lithium-ion battery (Model BCL1015) is included.

The newly developed Type BCL 1015 Lithium-ion Battery (10.8 V, 1.5 Ah) can be fully charged by the

Model UC 10SFL Charger in about 40 minutes.

The Type BCL 1015 is equipped with an overdischarge protection circuit, overload protection circuit, battery

overheat protection circuit and voltage monitoring circuit for each cell to prevent shorter battery life due to

overdischarge (overuse) or overcharge (excessive charging). This battery is safe thanks to these protection

circuits.

Precautions on using the Type BCL 1015 Lithium-ion Battery

The Type BCL 1015 Lithium-ion Battery is equipped with a protective function that automatically stops

output to prolong battery life. The motor may stop automatically in any of cases (1), (2) and (3) below, even

with the switch being held down during operation. This is because the protective function is activated. It is

not faulty.

Protective function Cause of trouble Countermeasure

(1)

Overdischarge

protection circuit

Battery voltage is decreased to about 6 V.

Charge the battery immediately

in such case.

(2)

Overload

protection circuit

Heavy-duty work

Release the switch and eliminate

the cause of the overload problem.

(3)

Battery overheat

protection circuit

Continuous operation

or heavy-duty work

Remove the battery from the tool

and cool it down.

SELLING POINTS

The shrub shear blade and grass shear blade come

standard with the Model CH 10DL (CG).

The grass shear blade is optional for the Model CH 10DL.

The shrub shear blade is optional for the Model CG 10DL.

-2-

Low charge warning lamp

(red LED)

x When the lamp lights,

recharge the storage

battery immediately.

Soft grip handle

Shrub shear Grass shear

A low charge warning lamp is included.

You can confirm remaining storage

battery power by operating the tool main

body under no load.

In case of low remaining storage battery

power, the low charge warning lamp (red

LED) lights up.

When the low charge warning lamp lights,

recharge the storage battery immediately.

A large work area can be covered on a single charge.

Product name

HITACHI

CH 10DL/CG 10DL

Shrub shear/Grass shear

One charge work area

44m

/15m

32m

/7m

*1: It is different according to the working condition.

A soft grip handle is attached.

The soft, antislip handle is made of elastomer resin to afford a firm grip.

The handle is thin along its circumference.

The handle is easy to grip and user friendly because it offers the shortest circumferential length in its class*.

Product name

HITACHI

CH 10DL/CG 10DL

Circumferential length of

storage battery

compartment (mm)

115 135

A large-size protector is attached.

A large-size chip receiver that covers the entire length of the blade collects cut branches and leaves,

thereby making it easy to perform cleanup after work. A safely usable, large-size protector is attached.

*According to data compiled

in March 2008 by Hitachi Koki.

-3-

pprox. 10 mm

pprox. 25 mm

djuste

pprox. 17 mm

djuste

An adjuster is included for adjusting shearing height.

When the adjuster is attached to the bottom of the main body, the shearing height can be adjusted in three

steps. You can easily adjust the shearing height for mowing lawns.

(a) When using the main body without the adjuster

(b) When the adjuster is attached to the main body with high-ribbed surface facing up

x Shearing height adjustments

-4-

1. Specifications

Model name CH 10DL (CG) /CH 10DL CG 10DL

Capacity

(shearing width)

190mm

(146mm for the USA)

170mm

No-load rotation speed

(at 20 qC, fully charged)

1,100 min

-1

Motor description DC magnet motor

Switch description Microswitch

Overall length x overall height

x overall width

491 x 133 x 165 mm

(with Model BCL1015 inserted)

333 x 133 x 170 mm

(with Model BCL1015 inserted)

Weight

1.3 kg

(with Model BCL1015 inserted)

1.2 kg

(with Model BCL1015 inserted)

Outer frame

Main body : ABS resin and elastomer

Storage battery : Polycarbonate resin

Charger : ABS resin

Type of battery Sealed cylindrical lithium-ion storage battery

Nominal voltage DC 10.8 V

Nominal life Charging/discharging: approximately 1,000 times

Nominal capacity 1.5 Ah

Charging time

Approx. 40 minutes

(with Charger UC 10SFL at ambient temperature of 20 °C (68 °F))

Battery

(Type

BCL 1015)

Charging

temperature

0 °C to 50 °C (32 °F to 122 °F)

Charger

(Model UC 10SFL)

x Overcharge prevention system:

(1) Stop current detection

(2) Battery surface temperature detection (thermostat or therrmistor)

x Input capacity: 35W

x The maximum allowable temperature of the Type BCL 1015 battery is

50 °C (122 ° F)

x Indication method: Pilot lamp indicates the charging state.

x Pilot lamp: On

---------------------------------During charging

Off---------------------------------Charging completed

SPECIFICATIONS

-5-

2. Charger/Standard Accessory Combination and Package Weight

Combination

Model name

(auxiliary symbol)

Storage

battery

Charger Standard accessories

Package

weight

(kg)

Approximate

package

dimensions

[depth x width x height (mm)]

CH 10DL(CG)

Grass blade, chip receiver,

adjuster, blade case, blow case

2.6 216 x 576 x 246

CH 10DL

Chip receiver, blade case,

blow case

2.5 216 x 576 x 246

CG 10DL

BCL 1015 UC 10SFL

Adjuster, blade cover,

blow case

2.6 216 x 576 x 246

3. Optional Accessories

(1) Storage battery

The following accessory should be purchased as a spare storage battery.

Model

name

Capacity Cooling

Remaining

power indicator

Code number

BCL1015

1.5Ah

Not

supported

None

331-067 (For Europe,Aust,NZ)

331-065 (For the USA and Canada)

(2) Blade

Shrub shear blade set

(Including blade case, crank cam (shrub) and

blade box)

Grass shear blade set

(Including blade cover, crank cam (grass) and

blade box)

Code No.330881

Code No.331257

(For the USA and Canada)

Code No.330887

-6-

1. Comparison of Specifications (Superior specifications:

)

HITACHI

CH10DL CG10DL

Manufacturer name

model name

Item

Shrub Shear Grass Shear Shrub Shear Grass Shear Shrub Shear Grass Shear

Battery voltage

10.8 3.6 7.2

Battery capacity

1.5 1.0 1.2

Battery description

---

Li-ion (outer package) Li-ion (inner package) Li-ion (inner package)

Shearing width

190

(146 for the USA )

170 115 80 115 100

Number of strokes

min

-1

1,100 1,000 800

Weight

1.3 1.2 0.6 0.5 1.1 1.0

Charging time

minute

40 300 420

Operating time

(practical) per charge

minute

40 30 40 30 40 30

Work area covered on

a single charge

44 15 32 7 36 3.3

Battery protection

circuit

---

Provided Not provided Not provided

Circumferential length

of switch section

115 135 125

Main body dimensions

165 x 491 x 133 170 x 335 x 133 75 x 360 x 110 83 x 280 x 110 75 x 475 x 130 75 x 370 x 130

Large-size protector

---

Provided Not provided Not provided

Handle bilayer

molding

---

Provided Provided Provided

Blade

mounting/demounting

---

Screws Tool-less Tool-less

Adjuster (shearing

height adjustment)

---

Provided

Not

provided

Not

provided

Vibration value

(Instruction

Manual/measured

value) [under no load]

m/s

1.3/1.5 --- / 0.8 --- / 1.37 2.5 / ---

Noise value

(Instruction

Manual/measured

value) [under no load]

dB (A)

84/72 87/76 82 / 67 82 / 67 81 / 75 81 / 77

Dimensions

(depth x width x height)

300 x 510 x 200 145 x 370 x 135 130 x 320 x 155

Cubic volume

30 7.2 6.4

Packing

Packing style

---

Blow case Steel can Cardboard box

*1: It is different according to the working condition.

COMPARISON WITH SIMILAR PRODUCTS

-7-

1. Handling Instructions

In the interest of promoting the safest and most efficient use of the Model CH 10DL/CG 10DL Cordless

Shrub Shear/Grass Shear by all our customers, it is very important when concluding a sale that the

salesperson carefully ensure that the buyer seriously recognizes the importance of the Handling

Instructions, and fully understands the precautions listed on the Caution Plate and Nameplate attached to

each tool.

A. Handling Instructions

Salespersons must be thoroughly familiar with the contents of the Handling Instructions in order to offer

appropriate advice to customers. In particular, customers must fully understand the precautions on using

cordless tools, which differ from those of ordinary electric power tools.

(1) Before use, ensure that the battery is fully charged.

A new battery is not fully charged. Even for batteries fully charged at the factory, long periods of

inactivity such as during shipment will cause a loss of battery charge. Customers must be instructed to

fully charge the battery prior to use.

(2) When charging a storage battery, only use the exclusive Model UC 10SFL charger provided with

the tool.

Given the newly designed rapid-charging feature (needing about 40 minutes), the use of other battery

chargers is hazardous.

(3) Connect the charger only to an AC power outlet.

Using any other power source (DC outlet, fuel powered generator, etc.) will cause the charger to

overheat and burn out.

(4) Do not use any voltage-increasing equipment (transformer, etc.) between the power source and

charger.

Note that using the charger at voltage higher than that indicated on the unit will result in malfunction.

(5) Conduct battery charging under ambient temperature from 0°C to 40°C (32°F to 104°F).

Special temperature-sensitive devices are employed in the charger to permit rapid charging. Ensure

that customers are instructed to use the charger in the indicated ambient temperature range. At

temperature under 0°C (32°F), the thermostat will not function properly, and the storage battery may be

overcharged. At temperature over 40°C (104°F), the storage battery cannot be sufficiently charged. The

optimum temperature range is from 20°C to 25°C (68°F to 77°F).

(6) The battery charger should not be used continuously.

At high ambient temperature, charging more than three storage batteries in succession will cause the

temperature of transformer coils to rise, possibly melting in the temperature fuse inserted inside the

transformer. After charging one battery, wait at least 15 minutes before charging the next battery.

(7) Do not attempt to disassemble the storage battery or charger.

Special devices, such as a thermostat, are built into the storage battery and charger to permit rapid

charging. Incorrect parts replacement and/or wiring will cause malfunctions that could result in fire or

other hazards. Instruct the customer to take these units to an authorized service center for necessary

repair or replacement.

PRECAUTIONS ON SALES PROMOTION

-8-

(8) Disposal of the storage battery (Type BCL 1015)

Ensure that all customers understand that the Type BCL 1015 Storage Battery should be returned to the

Hitachi power tool sales outlet or an authorized service center when the battery can no longer be

recharged or repaired. If thrown into a fire, the battery may explode.

B. Caution Plate

(1) The following cautions are listed on the Nameplate attached to the main body of the Type CH 10DL/CG

10DL.

[ For Europe ]

[ For the USA and Canada ]

-9-

(2) The following cautions are listed on the Nameplate attached to the Type BCL 1015 Storage Battery.

[ For Europe ]

[ For the USA and Canada ]

(3) The following cautions are listed on the Nameplate attached to the Type UC 10SFL Storage Battery.

[ For the USA and Canada ]

2. Precautions on Efficient Use of The charger and battery

(1) Battery possibly not rechargeable immediately after use

If the Type BCL 1015 Battery is exposed to direct sunshine for an extended period or becomes very

hot immediately after being used in the Model CH 10DL/CG 10DL, the pilot lamp may not light up

even though the battery is connected to the charger. The Type BCL 1015 Battery is rechargeable

when its temperature is within the range specified in the table below. Customers should be advised to

place a hot battery in a shaded area with good airflow and allow for sufficient cooling before

recharging. The cooling time required before charging varies from a few minutes to about 10 minutes,

depending on the load, duration of use and ambient temperature.

Battery temperature

Battery

Model UC 10SFL Charger

Type BCL 1015

0 to 50qC

-10-

Nut Holders (5)[5]

Nut M4 (4)[4]

Housing (1)[1]

1. Precautions on Disassembly and Reassembly

The numbers in parentheses ( ) below denote item numbers in the Model CH 10DL part price list.

The numbers in brackets [ ] below denote item numbers in the Model CG 10DL part price list.

Before making repairs, be sure to remove the storage battery (Model BCL 1015) from the main body.

Note that performing the following procedures with the storage battery mounted in place runs the risk of

sudden motor operation, thereby posing a safety hazard.

1. Removing the Blade Set

Before removing the Blade Set (CH) (38), Blade Set (CG) (48)[24] be sure to set the Blade Case (37),

Blade Cover (170) (46)[34] in position.

Remove the four Machine Screws M4x12 (8)[8] from the main body. The Blade Set (CH) (38), Blade Set

(CG) (48)[24] can then be removed together with the Bottom Cover (30)[35], with the Crank Case (27)[28],

Dust Felt (28)[29] attached.

2. Removing the Protector

Remove the two Machine Screws M4x12 (8)[8] that secure the Protector (6)[6]. The Protector (6)[6] can

then be removed from the main body.

3. Disassembling the Blade Assembly (CH)

(1) Remove the three U-nuts M4 (33).

(2) From top to bottom, sequentially remove the holder plate, blade (A), blade (B), and Distance Piece (34).

4. Removing Housing (B)

Remove the six Tapping Screws (w/Flange) D4x24 (black) (9)[9], and then remove housing (B), which is a

part of the Housing (1)[1]. When removing housing (B), hold down the controller portion of the Housing

(1)[1] in which the battery is to be placed. This facilitates the removal of housing (B) with the built-in parts

retained within housing (A).

Next, grasp the Motor DC 10.8 V (17)[17] and lift it out from housing (A). The entire power supply section

the Motor DC 10.8 V (17)[17], Switch (13)[13], and Controller (C) (16)[16]) can then be removed with ease.

5. Removing the Nuts

The Nut Holders (5)[5] are used to set and prevent the

Nut M4 (4)[4] from coming off the Housing (1)[1]. Use a

standard screwdriver or similar tool to pull off the Nut

Holders (5)[5] in order to remove the Housing (1)[1].

6. Disassembling the Power Supply Section

When removing the white and red internal wires from the Motor DC 10.8 V (17)[17], use a soldering gun to

remove the solder and then perform disassembly.

Internal Wires (14)[14] are used to solder the Switch (13)[13] and Controller (C) (16)[16] to their terminals,

respectively.

When removing the white and black internal wires from the Switch (13)[13], use a soldering gun to remove

the solder and then perform disassembly.

NOTE: Do not disassemble the Switch (13)[13] and Controller (C) (16)[16].

Disassembl

Procedure

REPAIR GUIDE

-11-

• Wiring diagram

Concave

Convex

Concave

Perform reassembly by reversing the order of the disassembly procedure. However, note the following

precautions:

1. Making Power Supply Section Wiring Connections

(1) Be sure to make wiring connections according to the wiring diagram. Pay attention to the colors of

Internal Wires (14)[14] and the terminals to be soldered.

(2) When soldering the white and red internal wires to the Motor DC 10.8 V (17)[17], pay attention to the

polarities of the Motor DC 10.8 V (17)[17]. The area around the plus (+) terminal of the Motor DC 10.8

V (17)[17] is marked red.

(3) When soldering the white, red and black internal wires to the terminals of the Switch (13)[13], pay

attention to the mounting direction.

(4) When connecting the Controller (C) (16)[16] to the Switch (13)[13], pay attention to the colors of

Internal Wires (14)[14] and the direction of soldering.

(5) Next, have on hand the assembly consisting of the Motor DC 10.8 V (17)[17], Controller (C) (16)[16]

and Switch (13)[13], and place this assembly within housing (A), which is a part of the Housing (1)[1].

In this case, align the concave part of the Motor DC 10.8 V (17)[17] with the convex part of housing (A).

Also make sure that the concave part of the Controller (C) (16)[16] is aligned with the convex part of the

Housing (1)[1].

Internal Wire (white)

Solder

Internal Wire (white)Solder

Internal Wire (red)

Switch (13)[13]

Internal Wire (black)

Controller (C) (16)[16]

Moto

DC 10.8 V

(17)[17]

(Red)

(white)

(white) -(black)

Reassembl

Procedure

Plus (+) terminal

Red mark

Concave

Minus (-) terminal

• Motor polarities

• Incorporating the controller (C)

-12-

Internal Wire (black)

Internal Wire (white)

Lock-off button

Internal Wire (red)

Switch (13)[13]

Trigger (12)[12]

Motor

DC 10.8 V (17)[17]

Controller (C) (16)[16]

LED

• Wiring diagram

Shrub shear

Grass shear

Next, position the LED so as to fit it into the hole in the Housing (1)[1].

Here, be careful not to catch any LED Internal Wires (14)[14] on adjacent parts.

Also make sure that the internal wires connecting the Controller (C) (16)[16] to the Switch (13)[13] are

incorporated in order of red, black and white.

(6) Incorporate the Lock-off Button (3)[3] and Trigger (12)[12] into the corresponding positions in the

Housing (1)[1].

2. Reassembling the Gears

(1) When incorporating the First Gear (20)[20], apply grease (Hitachi Motor Grease No. 29) to the outer

circumference of Shaft (B) (19)[19], insert Shaft (B) (19)[19] into the Washer D15 (18)[18] and the First

Gear (20)[20], and then complete reassembly so that the retaining groove section and locking flat

section of Shaft (B) (19)[19] mate with the rib and flat portion of housing (A). Here, make sure that the

Washer D15 (18)[18] is incorporated into position.

(2) When incorporating the Final Gear (21)[21], apply grease (Hitachi Motor Grease No. 29) to the outer

circumference of Shaft (A) (23)[23], insert Shaft (A) (23)[23] into the Washer D15 (18)[18] and Final

Gear (21)[21], and then complete reassembly so that the retaining groove section and locking flat

section of Shaft (A) (23)[23] mate with the rib and flat portion of housing (A).

3. Reassembling the Housing

(1) When installing housing (B), which is a part of the Housing (1)[1], make sure that no internal wire is

loose or caught.

(2) Properly position housing (B), which is a part of the Housing (1)[1], and tighten the six Tapping Screws

(w/Flange) D4x20 (black) (9)[9] (while being careful not to catch any internal wires).

4. Reassembling the Blade Set

(1) Make adjustments so that the oval

section of the crank of the Blade Set (CH)

(38)/Blade Set (CG) (48)[24] is as shown

in the right figure.

The figure shows the oval section with the

upper and lower blades being staggered.

-13-

Gear

Shaft (A) (23)[23]

Center hole in

Crank Holder (22)[22]

If the hexagonal portion of the Crank Holder (22)[22]

does not properly engage with the gear groove section,

fine-tune the Crank Holder (22)[22] until it properly

es with the

ear

roove section.

Make fine adjustments

so that the hexagonal

portions engage with

each other.

Crank Holder (22)[22]

Crank Holder (22)

Crank Cam Ass’y (24)

Blade Case (37)

Blade Ass’y (CH) (36)

Blade Cover (170)

(46)[34]

Crank Holder (22)[22]

Crank Cam Ass’y (39)[25]

(for grass)

Blade (CG) (42)[30]

(2) Next, attach the Crank Cam Ass’y (24)[25] and Crank Holder (22)[22] of the main body to the Blade Set

(CH) (38)/Blade Set (CG) (48)[24]. (Be sure to use the Crank Holder (22) [22] on the main body.)

(3) When mounting the Blade Set (CH) (38)/Blade Set (CG) (48)[24], align the center hole in the Crank Holder

(22)[22] with Shaft (A) (23)[23] of the main body, and then insert Shaft (A) (23)[23] into the center hole.

(4) To prevent the Blade Set (CH) (38)/Blade Set (CG) (48)[24] from coming off the main body, install the

reversed Bottom Cover (30)[35] over the blade assembly, and then tighten the four Machine Screws

M4x12 (8)[8] to secure it in place.

x Housing gear chamber of Housing (1)[1]: Hitachi Motor Grease No. 29 (15 g)

x Pinion section of Motor DC 10.8 V (17)[17]: Hitachi Motor Grease No. 29

x Outer circumferences of Shaft (A) (23)[23] and Shaft (B) (19)[19], teeth and both end faces of First

Gear (20)[20] and Final Gear (21)[21], blade sliding section, crank cam section, and blade holder

sliding section: Hitachi Motor Grease No. 29

x Both surfaces of Washer D15 (18)[18]: Hitachi Motor Grease No. 29

x Dust Felt (28)[29]: Cosmo Turbine Super 68 (Cosmo Oil)

x Tapping Screws (w/Flange) D4x24 (black) (9)[9] ----------------------- 1.96±0.49 N

•m (20±5 kgf•cm)

x Machine Screws M4x12 (8)[8] ----------------------------------------------- 1.18±0.2 N

•m (12±2 kgf•cm)

Precautions on Disassembly and Reassembly of the Battery Charger

For details of charger (Model UC 10SFL) disassembly/reassembly and related precautions, refer to the

Model UC 10SFL Technical Data and Service Manual.

Lubricant A

lication Points and Descri

tions

Screw Ti

htenin

Tor

ues

-14-

MODEL

Variable

Fixed

10 20 30 40 50 60 min.

Work Flow

CH 10DL

CG 10DL

General assembly

Bottom Cover

Blade Ass'y

(CH)

Crank Case

Crank Cam

Ass'y

Housing

Lock-off Button

Trigger

Switch

Controller (C

)

Crank Holder

Final Gear

First Gear

Shaft (A)

Shaft (B)

Motor DC

10.8V

STANDARD REPAIR TIME

(

UNIT

)

SCHEDULES

Model CH 10DL

CORDLESS SHRUB SHEAR

LIST NO. H832

(E1)

2009㨯3㨯10

CH10DL

TU01677

ᒻޓޓޓฬ

࿑ޓޓޓ⇟

ዤޓᐲ

30%

Rev.1

501

601

502

PART

CH 10DL

DESCRIPTION REMARKS

1 330-882 HOUSING 1

2 324-306 SPRING (A) 1

3 324-298 LOCK-OFF BUTTON 1

4 330-056 NUT M4 10

5 329-837 NUT HOLDER 2

6 330-879 PROTECTOR 1

7 949-423 WASHER M4 (10 PCS.) 6

8 949-217 MACHINE SCREW M4X12 (10 PCS.) 6

9 301-653

TAPPING SCREW (W/FLANGE) D4X20 (BLACK) 6

10 NAME PLATE 1

11 324-307 SPRING (B) 1

12 324-299 TRIGGER 1

13 320-786 SWITCH 1

14 330-058 INTERNAL WIRE 1

* 15 331-067 BATTERY BCL 1015 (EUROPE, AUS, NZL) 1

* 15 331-065 BATTERY BCL 1015 (USA, CAN) 1

16 329-839 CONTROLLER (C) 1

17 330-880 MOTOR DC 10.8V 1

18 329-835 WASHER D15 2

19 329-832 SHAFT (B) 1

20 330-055 FIRST GEAR 1

21 329-831 FINAL GEAR 1

22 329-833 CRANK HOLDER 1

23 329-830 SHAFT (A) 1

24 330-878 CRANK CAM ASS'Y 1 INCLUD. 25, 26

25 PIN (B) 1

26 CRANK CAM (A) 1

27 CRANK CASE 1

28 DUST FELT 1

29 323-211 MACHINE SCREW M4X8 (BLACK) 4

30 330-883 BOTTOM COVER 1

* 31 LABEL (USA) 1

* 32 LABEL (EURO) 1

33 319-931 U-NUT M4 3

34 996-689 DISTANCE PIECE 3

35 949-217 MACHINE SCREW M4X12 (10 PCS.) 3

* 36 BLADE ASS'Y (CH) 1 INCLUD. 33, 34, 35

* 36 BLADE ASS'Y (CH) 1 INCLUD. 33, 34, 35 FOR USA, CAN

37 330-884 BLADE CASE 1

* 38 330-881 BLADE SET (CH) 1 INCLUD. 4, 24, 27-29, 32, 36, 37, 601

* 38 331-257 BLADE SET (CH) 1 INCLUD. 4, 24, 27-29, 31, 36, 37, 601

FOR USA, CAN

39 330-886 CRANK CAM ASS'Y 1 INCLUD. 40, 41

40 CRANK CAM (B) 1

41 PIN (B) 1

* 42 BLADE (CG) 1

* 42 BLADE (CG) 1 FOR USA, CAN

43 323-211 MACHINE SCREW M4X8 (BLACK) 4

* 44 LABEL (EURO) 1

* 45 LABEL (USA) 1

- 2 - 3 - 09

*ALTERNATIVE PARTS

ITEM

NO.

USED

CODE NO.

PART

CH 10DL

DESCRIPTION REMARKS

46 328-030 BLADE COVER (170) 1

47 330-057 BLADE BOX 1

* 48 330-887 BLADE SET (CG) 1 INCLUD. 4, 27, 28, 39, 42, 45-47

* 48 331-258 BLADE SET (CG) 1 INCLUD. 4, 27, 28, 39, 42, 44, 46, 47

FOR USA, CAN

49 328-023 ADJUSTER 1

3 - 09 - 3 -

*ALTERNATIVE PARTS

NO.

USED

CODE NO.

ITEM

NO.

Page is loading ...

Hitachi CG 10DL Technical Data And Service Manual

Brand: Hitachi

Model: CG 10DL

Type: Technical Data And Service Manual

This manual is also suitable for

Download PDF

report

Hitachi CG 10DL Technical Data And Service Manual

This manual is also suitable for

Hitachi CG 10DL Technical Data And Service Manual

Related papers

Other documents